Search Documents

By D. L. Garthwaite, F. M. Stewart, F. K. Krebill

Pressure has been maintained in the Elk Basin Ten-deep reservoir since the initiation of inert gas injection in Sept., 1949. Oil is being produced under conditions favorable for gravity drainage, including high angle of dip, appreciable structural closure, and fairly good per~neability. Results being obtained are high per cent recovery of oil-in-place, sustained field productivity, reduced operating problems, and recovery of plant products. The high recovery has been calculated by alpplication of the gravity drainage theory described in an earlier AIME paper.' It is also confirmed from field performance by comparing nil recovery to date with gas cap spuce voided. GENERAL INFORMATION The Elk Basin field lies in Park County, Wyo., and Carbon County, Mont., approximately 50 miles east of Yellowstone Park. Located at the northern end of the Big Horn Basin. the field is situated on an elongated asymmetrical anticline (Fig. 1). The pressure maintenance project covered by this paper involves the Embar-Tensleep reservoir in this multi-pay field. Discovered in Nov., 1942, it has a proved productive area of over 6,300 acres. It consists of the 210-ft thick Tensleep sandstone of Pennsylvanian Age overlain by 40 ft of Embar dolomite of Permian Age. The two formations apparently are in communication with each other and are produced as a common source of supply. As 98 per cent of the reserves are contained in the Tensleep sandFtone, in this paper the Embar-Tensleep reservoir will he called simply the Tensleep. The reservoir is found at an average depth of 4,900 it, is approximately 7 miles long and 2 miles wide, and has a maximum oil productive closure of 2,330 ft. The strata dip an average of 21" on the west flank and 45" on the east. There are presently 132 Tensleep wells in the field drilled on 40-acre spacing; of these, 17 are shut in because of high gas-oil ratio (GOR) and eight are gas injection wells. Rock characteristics and related information for the pay section follow: Porosity, avg 10.7 per cent Permeability (air) from cores, avg 118 mds Permeability from PI'S 91 mds Connate water, avg 8 per cent Initial pressure (-400 ft) 2,234 psia Pressure April 1954 (-400 ft) 1.327 psia At high structural positions much of the better sandstone has connate water content of only 2 to 5 per cent as indicated by the coring of wells with oil in nearby Tensleep fields. In special imbibition tests, samples readily imbibed oil but repelled water. In tests on crushed samples, the sand grains rapidly settled in oil and carbon tetrachloride but formed a stable unsinking floc in water. This information indicates that the Tensleep sand is preferentially oil wet. The oil produced averages 29' API gravity and has a high sulfur content. Extensive sampling and testing have established the fact that characteristics of reservoir oil in this field vary greatly with structure, see Fig. 2. Additional detail on the variation of oil characteristics with structure at Elk Basin may be found in Reference 2. At original reservoir pressure the oil was undersatu-rated with gas, the bubble point being 1,250 psi at the crest but only 500 psi at the lowest elevation sampled. As noted on Fig. 2, other fluid properties—reservoir volume factor. solution ratio, gravity, viscosity, and hydrogen sulfide content—likewise vary greatly. These variations complicate mathematical analysis, for it is necessary to average these characteristics in order to enter them into reservoir engineering expressions. To further complicate analysis, sand-face pressure also varies greatly because of the increase in fluid head down structure. As an approximation, average properties under initial conditions may be read from Fig. 2 at the -450-ft elevation.

Jan 1, 1956

By Rolf Pollak, Jan Tegtrneier, Gerhard Keller, Horst Gerhardt, Wolfgang Müller, Dieter Tetzner

INTRODUCTION Under certain geological and mining conditions mining near the surface results in an intensive destruction of the overlying rock strata. If the system of mine openings remains filled with air after having completed all mining activities because the flooding of the mines depending on the morphology of the mining area does not exceed a certain level, this circumstance might result in dangers for the public. This is particularly true where uncontrollable air- ways occur within the destroyed rock or if former uranium mining areas are concerned. In these areas radon emanation resulting in undue radon concentration should be taken into account. This circumstance can be counteracted by suitable measures of ventilation. In the following the example of a uranium deposit in the Erzgebirge Mountains (Saxon Ore Mountains) is used to illustrate how statements about the ground flow through overlying rock can be made on the basis of systematic investigations. Finally comparisons with experience gained in coal mining yield orientation data which are used as input quantities in ventilation network calculations and in project preparation of mine fans. Last not least it is proved that endangering the population by radon can be excluded by installing an appropriate fan. INITIAL SITUATION From 1946 to 1989 the uranium deposit of Schlemal-Alberode was mined starting from superficial zones down to depths of 1,800 m. The total output amounted to 80,000 t of uranium, i.e. Schlemal Alberode is one of the largest uranium deposits in the world. The mine openings comprise a cavity of 40 million m3. Al- though thin seams (0.2 to 0.3 m) and steep to semi-steep veins (60 - 70 degrees on average) were extracted using the method of overhand cut-and-fill there were also deposit sections with larger thicknesses and poor ore zones, respectively, where especially after the war until about 1955 large openings were formed due to missing filling. Due to this uncontrolled, relatively "wild" mining considerable subsidence of the surface and fractures in the border zone of the subsidence area occurred. The town of Oberschlema was destroyed and an area of 0.14 km2 was damaged by mining involving a maximum subsidence of 6 m in the centre - called deformation area. The rehabilitation work for the deposit area of Schlemal Alberode involves the flooding of the openings up to a level of the Markus-Semmler-Sohle as long-term preventive measure. Fig. 1 shows the flooding level of October 1996. The level of the -540 m drift will probably be reached in June 1997. From that point of time a general rearrangement of the ventilation has to be made because the central return air ventilation via shaft 373 will no longer be possible. This shaft has no connection with the superficia1 system of mine openings. A new return air ventilation system based on shaft 382 as return air shaft will be designed (Fig. 1). The capacity of the future mine fan system will e.g. be determined by the flow conditions in the deformation area mentioned above. For this reason investigations were carried out in a test drift 13a on the level of the Markus-Semmler-Sohle in the stretching zone of the subsidence trough for several days (Fig. 2 and 3). INFLUENCE OF THE OPERATING CONDITIONS OF THE MAIN MINE FAN ON THE RADIATION SITUATION ON SURFACE The beginning of flooding in 1991 was also the beginning of the investigations into the options of future ventilation due to the reduction of the mining area. The first analyses of radon emanation made in May 1991 showed that only about 20 % of the total radon emanation result from systematically ventilated mine workings. This means that despite of existing dams the air streams through the majority of mine openings of the deposit. The analysis of the individual radon inflows illustrates the special problematic nature of the deposit involving all possible effects on the surface. The shutdown of the main mine fan over the long period between 2.10. and 6.10.1991 showed the essential influence of the operating conditions of the fans on the whole radiation situation on surface. Fig. 4 shows the comparison of the radon concentration level and its daughters during a 'normal" weekend with the level during long-term shutdown in the old 'Casino" of the papermill of Niederschlema. This papermill as well as the 'Casino" are situated in the outcropping zone of the deposit section of Niederschlema. The -60 m level was driven as the upper level in this area, from which the panels were driven to about 20 m below the surface. Also below the "Casino" there is such a panel in the vein 'Glirck", whose roof is directly situated below the building in a depth of 39 m. Directly next to it there is the raise 2 of the panel 'Namenlos" in a depth of 27 m. The graphics clearly shows the immediate increase in radon concentration as well as in the daughter concentration after the shutdown of the fans. The elimination of the artificially generated negative pressure results in the reversal of the convection direction due to the natural ventilating pressure. The interface structure allows the mine airto pass through aero- dynamic connections to the surface. Neglecting the meteorological parameters the concentrations of radon and its daughters in- creased by about 350 % as compared to a 'normal" weekend during longterm shutdown (i.e. in 4 days). Furthermore it could be noticed that a stationary state between the radon and its daughters has not been established in the period

Jan 1, 1997

By Koichi Nishimura

Japan's coal reserves are estimated at 8,583 million tons (according to the materials on X World Energy Conference,. 1976). Japan is a long island country in the shape of an elongated cashew nut whose top is pointing to the north and its lower tip is pointing to the west. And her major coal fields are located in the two extreme far parts of Hokkaido in the north and Kyushu in the south. On the other hand, Japan's major industrial center are located in the central part of the country far from either coal-producing areas. This fact places coal a great geographical disadvantage in comparison with petroleum whose refining bases are concentrated on the coastal regions virtually next to major industrial centers.

Jan 1, 1982

By W. A. Backofen, D. L. Holt

Push-pull fatigue tests have been carried out at 4.2°K, 77oK, and room temperature on two poly crystalline materials of widely different stacking-fault energy (?): pure copper (? - 70 ergs per sq cm) and the Cu-8 wt pct A1 alloy (? - 2.8 ergs per sq cm). Constant stress-amplilude was imposed and measurement was made of the plastic-strain amplitude (ep) at saturation. Lives extended from 104 to 106 cycles. Designating lives at the various temperatures by NRT, N77, and N4.2. the ratios N77/NNT and N4.2/N77 ranged from 3.5 to 18 under the condition of common Ep . Metallo-graphic examination revealed different crack morphology in Cu-8 Al fatigued at room temperature, and at 77" and 4.2oK. At room temperature, cracks lay in or near grain and lain boundavies; at 77o and 4.2oK. cvacks were transcrystalline. Tests on single crystals of Cu-8 A1 showed that such a change in the cracking mode in polycrystallitle material accounted for a factor of- about 3.25 in N77/NRT . The longer life at lower tewperatztre (conslant cp) has heels attributed to two deuelopinents: a reduced production of the dislocation tangles and subgrain boundaries which serve as paths of rapid cracking, and suppression of oxygen chetni-sorption at the crack tip It was concluded that in both materials the luller accounted for an extension of the life at 4.2oK beyond that at room temperature by a factor of 15. XV ECENT experiments on the fatigue of Cu-A1 alloys in the so-called high-cycle range (greater than lo4 cycles) have emphasized the importance of stacking-fault energy (y) as a quantity affecting crack propagation rate and fatigue life.1,2 It was found in comparisons at essentially fixed plastic-strain amplitude that crack growth rate decreased by a factor of about 5 over the composition range from copper (? - 70 ergs per sq cm) to Cu-8 wt pct Al (? - 2.8 ergs per sq cm). The argument was made that, when stacking-fault energy is high, cross slip and climb are favored, so that dislocation tangles and/or subgrain boundaries form more readily under cyclic loading. Since the boundaries and tangles act as paths of rapid crack propagation ,3, 4 life is shortened as a result. However, when stacking-fault energy is reduced (as by alloying), cross slip and climb become more difficult, with the result that substructure formation is retarded and growth rate is also reduced. A purpose of the present work was to investigate the substructure effect in relation to temperature. As temperature is lowered, ? is varied only slightly (if at all), but decreased thermal activation can interfere with cross slip and climb. Thus substructure formation could be curtailed and life increased. Fatigue life in the high-cycle range is also known to be strongly influenced by environment. Working with copper, Wadsworth and Hutchings observed that life in a vacuum of 10-8 mm Hg exceeded life in air by a factor of 20.5 They isolated oxygen as the agent that furthered cracking. While the details are still unclear, a requirement in any mechanism of oxygen-accelerated cracking is that there be chemisorption at the crack tip. That could prevent welding on the compression half cycle,= interfere with reversal of slip,1, 6 or aid in breaking metal-metal bonds at the crack tip.5'7 In the work being reported here, temperature was lowered by immersion in liquid nitrogen and helium, which also served to reduce both the oxygen concentration and chemisorption rate. A possible effect upon life, i.e., a lengthening, had to be recognized. Several researchers have determined fatigue lives at low temperatures presenting their results in the form of stress amplitude (S) vs cycles in life (N) curves.8-11 Such curves reflect, primarily, the fact that metal is strengthened by lowering temperature; effects of substructure and changing environment tend to be masked. The difficulty can be overcome by comparisons based on identical plastic-strain amplitudes, and in the present work the dependence of life on both plastic strain and stress amplitude was established. EXPERIMENTAL Materials. The principal materials were polycrystal-line copper (? - 70 ergs per sq cm)" and the Cu-8 wt pct Al alloy (? - 2.8 ergs per sq cm),I3 the latter being near the limit of solubility of aluminum in copper and having, therefore, the lowest stacking-fault energy in the CU-Al system. Specimens were machined from 0.118-in.-diam cold-swaged rods of high-purity (99.999 pct) copper and the Cu-8 Al alloy, the latter produced initially in a graphite boat by induction vacuum melting a mixture of 99.999 pct Cu and 99.99 pct Al. The machined specimens were annealed to produce mean grain diameters of about 0.070 mm in copper and 0.190 mm in the alloy. Specimen dimensions are given in Fig. 1. Values of the tensile yield stress, ultimate strength, uniform strain (determined by the Considgre construction), and reduction of area, for both materials at 4.2oK, 77oK, and room temperature, are listed in Table I. The tensile apparatus in which these results were obtained has already been described.14 Apparatus. Specimens were fatigued in push-pull with a machine that is illustrated schematically in Fig. 2. The specimen is first soldered into the top grip (1) with Woods metal, and the grip is then screwed into the inner tube (2) which is connected to the drive rod of the Goodmans vibration genera-

Jan 1, 1968

By R. W. Snyder, W. H. Guilinger, B. S. Gottfried

Two numerical methods are presented JOT solving the equations Jor one-dimensional, multiphase /low in porous media. The case oF variable physical properties is included in the Formulation, although gravity and capillarity are ignored. Both methods are analyzed mathematically, resulting in upper and lower bounds for the ratio of time step to mesh spacing. The methods are applied to two- and three-phase waterflooding problems in laboratory-size cores, and resulting saturation and pressure distributions and production histories are presented graphically. Results oJ the tuo-phase flow problem are in agreement with the predictions of the Buckley-Leuerett theory. Several three-phase flow problems are presented which consider variations in the water injection rate and changes in the initial oil-and ujater-saturation distributions. The results are different physically from the two- phase case; however, it is shown that the Buckley-Lez~erett theory can accurately predict fluid interlace velocities and displacing-fluid frontal snturations for three-phase flow, providing the correct assumptions are made. The above solutions are used as a basis JOT et~aluuting the numerical methods with respect to machine time requirements and allowable time step for a fixed mesh spacing. INTRODUCTION Considerable progress has been made in recent years in obtaining numerical solutions of the equations for two-phase flow in porous media. Douglas, Blair and Wagner2and McEwenll present different methods for solving the one-dimensional case for incompressible fluids with capillarity (the former using finite differences, the latter with an approach based upon characteristics). Fayers and Sheldon4 and Hovanesian and Fayers8 have extended these studies to include the effects of gravity. West, Garvin and Sheldon, l4 in a pioneer paper, treat linear and radial systems with both capillarity and gravity and they also include the effects of compressibility. Douglas, Peaceman and Rachford3 consider two-dimensional, two-phase, in compressible flow with gravity and capillarity and Blair and Peaceman1 have extended this method to allow for compressible fluids. No one, however, has examined the case of three-phase flow, even for the relatively simple case of one-dimensional flow of incompressible fluids in the absence of gravity and capillarity. In obtaining a numerical technique for simulating forward in situ combustion laboratory experiments, Gottfried5 has developed a method for solving the one-dimensional, compressible flow equations with any number of flowing phases. Gravity and capillarity are not included in the formulation. The method has been used successfully, however, for two- and three-phase problems in a variable-temperature field with sources and sinks. This paper examines the algorithm of Gottfried more critically. Two numerical methods are presented for solving the one-dimensional, multi-phase flow equations with variable physical properties. Both methods are analyzed mathematically, and are used to simulate two- and three-phase waterflooding problems. The numerical solutions are then taken as a basis for comparing the utility of the methods.

Jan 1, 1967

By R. W. Carpenter, J. C. Ogle

It is possible, by using pack-rolling instead of conventional rolling, to reduce a number of metals to thicknesses of 2µm or less. Such thinfoils are generally made at room temperature without intermediate annealing. In addition, pack-rolled foils fail by developing pinholes at thicknesses near 2µm instead of developing the shear cracks usually observed in cold-rolled ductile metals. This paper presents the results of a general investigation of the deformation substructure and texture developed in copper and iron pack -rolled from 130 to about 2µm thickness. Electron microscopy showed that in both metals a fine (0.2 to 0.5?µ m) deformation subgrain structure formed during pack-rolling; in neither case was this substructure grossly different from substructures formed during conventional rolling. The deformation texture formed in pack-rolled iron was quite similar to usual bcc textures; however, in the case of copper, the cube texture was stable during pack-rolling and the normal copper deformation texture was unstable. It is shown analytically that the constraining pack induced a large hydrostatic pressure in the foils during pack-rolling. The pinhole failure mechanism is attributed to the presence of the large hydrostatic pressure during pack-rolling; this strongly suppressed the growth of shear cracks. The stability of the cube texture in copper is also probably due to the unusuul stress distribution developed during pack-rolling. EXPERIMENTS at several laboratories have shown that very thin foils of the common structural metals and many of the rare earths can be made by "pack-rolling". 1-3 The technique was originally developed to make specimens for nuclear scattering experiments and foils for X-ray filters. It is also useful for making experimental laminar metallic composite bodies and foils thin enough for direct examination by ultra-high voltage electron microscopy without the need for special thinning techniques. Pack-rolling in the present context means a three-layer pack, with the material to be rolled into foil comprising the center layer. The outer two layers, which constrain the foil during reduction, are ordinarily austenitic stainless steel. Typically, a 130 µm (0.005 in.) metal strip can be reduced to a final thickness of 2 µm or less by this process. This is accomplished at room temperature, without intermediate annealing. It has been observed that foils produced by this process do not exhibit at any stage of their reduction the severe work-hardening found in strip rolled by conventional cold-rolling methods. Neither is the failure characteristic the same."&apos; Conventionally cold-rolled ductile metal strip fails by developing shear cracks on planes whose normals nearly bisect the angle between the rolling direction and normal to the rolling plane; these are planes of maximum shear stress. In pack-rolling this mechanism has not been observed; failure occurs by the formation of pinholes on the foil surface (penetrating the foil). If pack-rolling is continued the hole density increases. These differences in behavior imply the existence of appreciably different substructure in pack-rolled foils compared to substructure in conventionally rolled material, or perhaps that the geometry of pack-rolling has an effect on the foil behavior. This paper describes an investigation of deformation substructure and texture in some specimens of pack-rolled copper and iron, and some considerations of the stress distribution in the foils during rolling that result from the geometry of pack-rolling. EXPERIMENTAL DETAILS Three different materials were used for pack-rolling in the present work: soft copper sheet (99.8 pct Cu, 0.03 pct 0, electrolytic tough pitch) and two types of iron, Ferrovac E* and Armco iron. Each was "Crucible Stccl Co. initially in the form of 130 µm annealed strip with grain size ranges of approximately 10 to 40 µm. The initial texture of the copper (determined as noted below) was the normally observed cube type (001)[100]; there was evidence of a small amount of material in the cube-twin orientation reported by Beck and Hu.4 The initial texture of the Ferrovac E was similar to that reported for recrystallized iron by Kurdjumov and sachs,5 who list the principal orientations as {111}<112>, {001}<110> 15degfrom RD and a weak component {112}(110) 15 deg from RD. The starting texture of the Armco iron was not determined. Pack-Rolling Procedure. A four-high mill was used for all specimens. The work roll and backing roll diameters were 1.625 and 5.25 in., respectively. The peripheral roll speed of the work rolls was about 2.5 in. per sec. All foils were initially reduced from 130 to 100 µm by conventional straight rolling and then inserted into a pack, without any intermediate annealing, for further reduction. The pack consisted of an 0.033 in. (838 µm) thick 3 by 6 in. polished sheet of austenitic stainless steel, folded to make a 3 by 3 in. jacket. After folding, the jacket was given a small reduction to close the fold tightly before insertion of the foil. During pack-rolling a constant change in roll spacing was made every third pass. The roll-spacing change corresponded to a 5 pct reduction in thickness for a new pack. This approached a 10 pct reduction when the pack had decreased to about half its original thickness. At this point the deformed pack was discarded and a new one

Jan 1, 1970

By Robert F. Chaiken

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,000° C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau&apos;s first field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the. 1900&apos;s and was surface mined in the 1940&apos;s. In the winter of 1961~62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but, not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report, although considered part 2, is actually the last of a five-part series that describes the Calamity Hollow Mine Fire Project. It was written last because it involved the analysis of a substantial body of data describing in detail the results of a continuous 4-month burnout operation. The first report, part 1, describes the design and construction of the field installation. Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and part 5 describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration, which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is suffIcient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water injection-fume exhaustion quenching procedure are planned.

Jan 1, 1989

By C. E. Wood, E. P. Barrett, T. L. Joseph

The invention of the Bessemer converter process in 1856 added great impetus to the manufacture of steel and is one of the outstanding contributions to process metallurgy. Although the process of refining pig iron by passing air through the molten metal bears the name of Henry Bessemer, it should be mentioned in passing that William Kelley of Eddysville, Ky., worked on the process as early as 1847. Kelley was granted a patent on the process in 1857, inasmuch as he was able to prove priority in discovery.&apos; After considerable litigation in 1865 the respective interests of Kelley and Bessemer were combined. On Sept. 10, 1856, Robert Mushet of England obtained his first patent on the application of manganese to cast steel. Mushet anticipated trouble in purifying iron by passing currents of air through it: His patent specified that steel made in this way often contained flaws and was red short or cold short. Mushet understood the refining of pig iron into steel well enough to realize the difficulties likely to be cncountered from oxidation of the iron. Mushet was not only an inventor; he was also an investigator. He understood the principle of selective oxidation which takes place in the converter process, and he realized therefore that the remedy for over-oxidation was attainable if a suitable metal could be found at a reasonable cost and in sufficient quantities. His first experiments were made in small crucibles holding a few ounces of metal. Later his work was conducted on a larger scale and with complete success. Manganese had been used in making steel a quarter of a century before the converter

Jan 1, 1927

By H. Hu

Observations were made on the recrystallization of a 70 pct cdd-rolled silicon-iron crystal with an initial orientation of (113) [332]. Its polygonization and recrystallization characteristics were studied. Results indicated that re crystallization tendency of the deformed crystal is much weakened by the polygonization of the matrix. Complete recrystallization in such specimens is achieved by the growth of recrystallized grains of sufficient size and of the right orientations in relation to the matrix. Evidence was also furnished which suggests that the difference in the re-crystallization tendency is a result of the difference in the severity of lattice bending rather than the difference in orientation of the deformation texture. DUNN and Koh1,2 have made an extensive study on the rolling and annealing textures in silicon-iron crystals. Their results indicated that the recrystallization tendency can be widely different in crystals with different orientations. A particularly interesting example of their results was a crystal with an initial orientation of (113) [332], which developed a deformation texture of (001) [110] after 70 pct cold-rolling. Recrystallization in this crystal took long time anneals at high temperatures. Other crystals having different orientations recrystallized very rapidly. Wiener and corcoran3 have observed the retention of the (100) [011] deformation texture in a low-temperature annealed specimen of a commercial silicon-iron alloy, corresponding to areas of light-etching low-angle boundaries in the annealed struc-

Jan 1, 1960

By J. W. Horne, W. B. Shirey

"INTRODUCTION The United States Bureau of Mines in cooperation with the State of Colorado at the University of Colorado has conducted experiments to determine the amount and composition of the noncondensable gases evolved when crude shale oil is distilled under pressure.Hydrogen sulphide is one of the components found in the complex mixture of gases produced by the distillation of shale oil under pressure. This paper deals with the apparatus and method used in determining the amount of hydrogen sulphide evolved in the laboratory experimental cracking stills.The study required a complete extraction of all the hydrogen sulphide from the gas stream after it left the water-cooled distillate condensers and before the as stream entered the charcoal absorber for removing the light naphtha. In devising the method it was necessary to take into account a constant variation of velocity, pressure, and percentage of sulphide in the total gas stream coming from the still.Ordinarily, the quantitative determination of hydrogen sulphide in Gas is made by analyzing small samples taken at regular intervals. This estimation can be accomplished by use of the Bunte gas burette as modified by Tutriler,4 or by a similar method. In the industries where the flow of as is constant end of uniform composition, this practice is sufficiently accurate for plant control. For experimental work where many variables have to be taken into consideration, as in the case at hand, these methods are not applicable."

Oct 1, 1931

By M. L. Rudee, R. A. Huggins

Samples of iron containing nitrogen or carbon have been given treatments similar to those used in cold-work peak (CWP) measurements and examined by transmission electron microscopy. It was observed that the unusual and nonreproducible behavior of the carbon CWP can be explained by a strong tendency for carbon to form grain boundary precipitates at temperatures below those used for CWP measurements. These precipitates dissolved at the temperatures used in the CWP measurements. There was no evidence for nitrogen precipitation at grain boundaries. There was no indication of precipitation along dislocations in either carburized or nitrided samples given treatments similar to those of CWP measurements. Although it is possible that subelectron-microscopic clustering had occurred, this observation supports the theories of the CWP that are based on continuous atmospheres rather than on individual precipitates. In an earlier paper,&apos; the present authors developed a new distribution function to predict the occupation of sites for interstitial impurity atoms around a dislocation. When this distribution was applied to the case of carbon and nitrogen in iron, it predicted that, if the temperature dependence of the concentration of solute atoms in the matrix was controlled by the presence of equilibrium carbide or nitride precipitates, the tendency for nitrogen to segregate to dislocations would be greater than that for carbon even though their binding energies to dislocations are identical. The cold-work internal-friction peak (CWP) is considered by most authors to be produced by the interaction of interstitial impurities with dislocations. Many investigators have studied the CWP in iron containing carbon and nitrogen and have observed a significant difference between its behavior in the two cases. In this paper a series of experiments will be reported that were initiated to determine whether the application of the new distribution function would explain the observed differences between the carbon and nitrogen CWP. Although it was found that the distribution function, pev se, did not explain the differences, the differences became clear, and some insight into the mechanism of the CWP was realized. Before reporting the present experiments, the literature pertaining to the differences between the carbon and nitrogen CWP in iron and the various mechanisms proposed for the CWP will be reviewed. LITERATURE REVIEW Snoek2 first observed the CWP in iron specimens containing nitrogen, but also reported a weak and unreliable peak in carburized samples. Later, Ke3 established that the CWP height was proportional to the degree of deformation. The presence of nitrogen alone would produce a peak of the same size as found in a sample containing both nitrogen and carbon, and KG concluded that the CWP was caused by nitrogen. In a discussion of G&apos;s paper it was reported that Dijkstra had investigated the CWP in samples that contained only carbon. He found it to be much smaller than the nitrogen peak and "unstable". KG et al.4 charged specimens of iron with both carbon and nitrogen. They observed that the carbon CWP was much smaller than that observed in nitrided samples, but that aging at 300°C caused the carbon peak to increase. A similar treatment produced no change in a nitrogen peak. Annealing at higher temperatures caused the height of the CWP in both the nitrogen and carbon samples to decrease. This behavior was also observed by Kamber et al. 5 who found that the activation energy for the annealing of the CWP was identical with the activation energy for the self-diffusion of iron. They concluded that the annihilation of dislocations by climb caused the reduction in the CWP height. Kamber et al. studied the "unstable" carbon peak in detail. They measured both the Snoek and CWP during various aging treatments. In carburized samples, aging at 100°C caused the Snoek peak to disappear, although the CWP peak remained small. However, a subsequent treatment for 5 hr at 240°C caused the CWP to reach a maximum. They proposed that an additional location for the carbon, other than whatever site produced the CWP, is present. In nitrided samples the CWP was completely developed as soon as a measurement was made; additional sites are not present. No explanation of either the additional site or the difference in the behavior of carbon and nitrogen was offered. petarra5 performed a systematic study of the effect of composition on the CWP. Using three kinds of "pure" iron, he showed that there was a residual CWP when the carbon and nitrogen concentrations had been reduced to less than that detectable by Snoek-peak measurements. He observed the same general annealing behavior and composition dependence as previous investigators, with the following exceptions. On first measuring the carbon CWP, it was found to be identical with the residual peak, and essentially independent of the carbon content. If the CWP was measured a second time in the same sample, it increased in size, but was still only about one-fourth the size of a CWP in a sample of the same iron nitrided to the same composition. On the other hand, a series of annealing experiments showed that the nitrogen CWP was not al-

Jan 1, 1967

Pisolitic iron ores (also known as channel iron deposits) are an important resource of medium-grade iron ore in the Hamersley Province of Western Australia. They are a special case of transported pisolitic ferricrust, differing from normal transported ferricrust only in the exceptionally high iron and low alumina content. The pisoids typically range up to 5 mm in diameter with abundant particles of ferruginised fossil wood up to 15 mm in maximum diameter preserved in the sediment. Field observations indicate that pisoliths are commonly initiated by the action of raindrops on iron-rich soil. Pisolites form by the impact of raindrops forming coated beads of ferruginous soil, which after dehydration obtain additional coatings during successive showers. Thick deposits of pisolite that are transported and deposited primarily by sheetwash form in the distal regions of the pediment. A size range limited to particles that may be transported by extremely shallow water characterises the abundant fossil wood fragments. The absence of fine sedimentary layering in pisolitic iron ores is explained by the action of soil-forming processes after deposition, while the major coarse bedding features derive from successive erosional and depositional events in the evolution of the pediment. They are not deposited in channels by rivers which, in arid to semi-arid conditions, typically deposit quartz sands and gravels with characteristic point bars and current bedding, abundant ferruginous granules, but rarely pisoids. However, they may fill abandoned river channels.

Jan 1, 2007

By G. P. Tiwari

Recrystallization and grain growth in thoria dispersed nickel and nichrome were recently studied by Webster as a function of temperature and deformation. The unexpected part of these results was that specimens which had received heavier deformation developed greater resistance to recrystallization. Retardation of recrystallization was accompanied by the formation of voids around thoria dispersion. To explain these results, Webster suggested that the formation of void around the particles increased the effective size of thoria particles. This resulted in greater impediment to the grain-boundary migration and as a consequence the recrystallization of the matrix is retarded. In the present note an alternative and more probable explanation for the effect of voids on recrystallization is presented. The exact mechanism of void formation in thoria dispersed nickel or nichrome is not known. However, it is reasonably certain that it must be preceded by the stress concentration in the matrix around thoria dispersion during the deformation.&apos;&apos; The resulting stress concentration must be sufficient enough to supply the surface energy for the new surfaces created. Further, the decrease in the strain energy of the matrix surrounding the potential void nucleus must be larger than the surface energy of the newly created surface. The release of strain energy due to formation of crack results in a strain free cylinder of the material around the voids.13 If the void formation is not localized, at few points only (as is the case here), this process may lead to considerable amount of release of strain energy of the matrix. The pattern of recrystallization behavior of single phase homogeneous matrix as well as the matrix having a second phase dispersion is same except for the fact recovery and recrystallization are more clearly delineated.14 In general, the recrystallization temperature is lowered (i.e., recrystallization is easier) with increase in the amount of cold work. This is due to the increase in stored energy in the matrix with increasing amount of deformation. If somehow there is a relaxation of strain energy in the matrix, the recrystallization should become difficult because of the decrease in the amount of stored energy available for recrystallization. Since the formation of voids leads to a decrease in the strain energy of matrix, the recrystallization of the matrix would be inhibited due to the formation of voids during deformation prior to recrystallization. It has been observed by earlier workers15&apos;16 that the presence of preexisting voids in a matrix retards the recrystallization. The essential issue here is how do the voids act to produce this effect. If the voids influence recrystallization only by blocking the grain boundary migration, then the effect should be maximum when they are present almost exclusively along grain boundary. These conditions are obtained during high temperature deformation. However, the voids produced due to creep along grain boundary are not able to prevent recrystallization17 suggesting that they are not effective in blocking grain boundary movement. Recently it was shown by Davies and Williams that the voids can act as sinks for vacancies." As a result the processes dependent on vacancy diffusion like recovery, recrystallization, dislocation climb, and so forth, will be hindered. This fact may be responsible for inhibition of recrystallization during subsequent deformation and annealing cycles. It is to be noted here that there is a large difference between the density of voids in creep experiments and the other experiments where retarding effect of voids on recrystallization is seen. The voids in former may number up to l04 to l05 per sq cm whereas in latter cases the voids density is typically around 1010 to 1013 per sq cm. It appears that the decrease in supply of vacancies in creep is insufficient to adversely affect the recrystallization due to low void population. The author is grateful to P. Das Gupta and S. P. Ray for helpful discussions. Author&apos;s Reply D. Webster Tiwari appears to have misunderstood the nature of grain boundary-particle interactions. Tiwari (quoting Cahn) states that second phase particles become more effective as they become smaller, therefore as the voids in TDNiC make the thoria particles effectively bigger their ability to resist grain boundary movement is impaired. This particle size argument was originally proposed in the form of an equation by Zener 20 years agol9 and is not necessarily valid as is discussed below. However, assuming it is valid, it predicts a greater boundary restraining effect by smaller particles simply because their combined cross sectional area is greater at a constant volume. If the number of particles remains the same and their effective size increases, as in the present case, Zener&apos;s equation predicts a greatly reduced grain size. This is because the effect

Jan 1, 1970

By L. A. Panek, A. J. Barry, John A. McCormick

"INTRODUCTION During recent years, roof bolting has become widely accepted as a systematic method of supporting both coal- and metal-mine roofs. Today, over 2 million roof bolts are installed monthly. Most of the information on bolt installation procedure reported to date (1,2,3,4,5,6) 3/ has been obtained by trial and error by individual groups or operators. To insure good roof control, experience and field tests have indicated that roof bolts should be installed immediately after the exposure of new roof, and they should be preloaded enough to minimize sag of the roof over the opening. The question of the proper initial preload for roof bolts is under study, although it is a general practice to impose an initial load on a bolt of approximately 10,000 pounds. This created a problem of measuring bolt loads at installations in underground mines, which was partly solved by using a commercial-type torque wrench; a device that permits a direct reading of the torque applied to the nut on a roof-bolt assembly from which the corresponding load can be determined by referring to specifications furnished by the manufacturers. However, considerable apprehension was expressed regarding the accuracy of this measuring procedure because of variations in the manufacture of roof-bolting materials and the degree of care exercised in making bolt installations. In the process of loading a bolt, only a small part of the effort is expended in producing strain in the bolt - the larger part of the effort is used in overcoming frictional effects in the nut-bolt-washer assembly. These frictional effects are subject to many factors, such as condition of threads, type of lubrication, if any, the finish on the nut and bearing plate, and the alinement of the bearing plate on the bolt. The object of this investigation was to determine the accuracy with which the load developed in a slotted-type roof bolt installed in a conventional manner in shale or sandstone roof rock can be determined from the torque applied to the nut.This report is the first of a series relating to basic research in roof bolting in underground mines. A future report will cover results obtained using expansion-type bolts under similar conditions. Other reports will consider the efficiency of bolt anchorages, the long period stability of bolts, and the design of safe and efficient roof-bolting systems."

May 1, 1953

By D. A. Beattie

Three novel dextrin polymers of varying functional group chemistry but similar molecular weight have been used to depress talc in single and mixed mineral studies. The mixed mineral system was a model sulphide ore consisting of talc, pentlandite, and chalcopyrite. Adsorption isotherms for the three polymers on both valuable and gangue mineral phases were determined to give initial clues as to the ability of the polymers to depress talc. Flotation testing revealed a distinct hierarchy of effectiveness of the polymers in the depression of talc in the single mineral system (MP Dextrin > CM Dextrin > Dextrin TYM), reflecting the observed adsorption affinity and adsorbed amount of the polymers on talc. However, a different order of effectiveness was observed for talc depression in the mixed mineral system (CM Dextrin > MP Dextrin > Dextrin TYM). Competition between the valuable and gangue mineral phases for uptake of MP Dextrin is responsible for its observed decrease in efficiency in mixed mineral flotation. All three polymers were found to be reasonably selective in their action, although at high dosages the polymers began to affect the flotation of the valuable minerals.

Jan 1, 2006

By F. N. Rhines, A. H. Grobe

At elevated temperatures the oxide of silver is unstable in the air at atmospheric pressure, consequently no external oxide scale forms upon pure silver under conditions of high-temperature annealing. When small quantities of certain alloying elements are present in the silver, the formation of a thin external scale is possible1 and in addition there may form a subscale composed of the oxide of the solute element precipitated within the body of the silver. Norbury2 and Leroux and Raub3 have reported internal oxidation (subscaleiormation) in alloys of silver with 2, 7.5, and 30 per cent of copper. The presence of the subscale is believed to be responsible, at least in part, for the objectionable "fire mark" in Sterling silver.4 Several other alloys of silver, after oxidizing heat-treatments, are known to exhibit undesirable polishing characteristics that may be the result of internal oxidation. Except for the absence of an external scale of silver oxide, it is to be anticipated that silver alloys will prove to be very similar in their oxidation behavior to the alloys of copper, the oxidation characteristics of which have been studied in some detai1.5,6 The present research confirms this anticipation. The oxidation of a series of 20 dilute alloys of silver has been studied metallographically; some types of subscale not encountered among the copper alloys have been found. Instances of internal oxidation in alloys of most of the metals of the 1-6 and VIII groups of the periodic system are on record, but evidence of this type of oxidation in alloys of the metals of the intermediate groups is lacking. A number of the metals of the intermediate group, among them cadmium, lead, tin, and zinc, appear to provide the conditions essential to subscale formation; i.e., they form oxides with a relatively low negative free energy of formation, they dissolve other metals that form more stable oxides, and, presumably, oxygen will diffuse through them. In a study of 40 alloys of these white metals only a few cases of internal oxidation have been found. The probable reasons for this difference in behavior will be discussed presently. Experimental Procedure Silver.—The silver alloys employed in the oxidation studies were prepared in heats of 30 grams each from high-purity silver (99.993 per cent Ag)* and the purest avail-

Jan 1, 1942

By A. H. Grobe, F. N. Rhines

At elevated temperatures the oxide of silver is unstable in the air at atmospheric pressure, consequently no external oxide scale forms upon pure silver under conditions of high-temperature annealing. When small quantities of certain alloying elements are present in the silver, the formation of a thin external scale is possible1 and in addition there may form a subscale composed of the oxide of the solute element precipitated within the body of the silver. Norbury2 and Leroux and Raub3 have reported internal oxidation (subscaleiormation) in alloys of silver with 2, 7.5, and 30 per cent of copper. The presence of the subscale is believed to be responsible, at least in part, for the objectionable "fire mark" in Sterling silver.4 Several other alloys of silver, after oxidizing heat-treatments, are known to exhibit undesirable polishing characteristics that may be the result of internal oxidation. Except for the absence of an external scale of silver oxide, it is to be anticipated that silver alloys will prove to be very similar in their oxidation behavior to the alloys of copper, the oxidation characteristics of which have been studied in some detai1.5,6 The present research confirms this anticipation. The oxidation of a series of 20 dilute alloys of silver has been studied metallographically; some types of subscale not encountered among the copper alloys have been found. Instances of internal oxidation in alloys of most of the metals of the 1-6 and VIII groups of the periodic system are on record, but evidence of this type of oxidation in alloys of the metals of the intermediate groups is lacking. A number of the metals of the intermediate group, among them cadmium, lead, tin, and zinc, appear to provide the conditions essential to subscale formation; i.e., they form oxides with a relatively low negative free energy of formation, they dissolve other metals that form more stable oxides, and, presumably, oxygen will diffuse through them. In a study of 40 alloys of these white metals only a few cases of internal oxidation have been found. The probable reasons for this difference in behavior will be discussed presently. Experimental Procedure Silver.—The silver alloys employed in the oxidation studies were prepared in heats of 30 grams each from high-purity silver (99.993 per cent Ag)* and the purest avail-

Jan 1, 1942

By A. H. Grobe, F. N. Rhines

AT elevated temperatures the oxide of silver is unstable in the air at atmospheric pressure, consequently no external oxide scale forms upon pure silver under conditions of high-temperature annealing. When small quantities of certain alloying elements are present in the silver, the formation of a thin external scale is possible&apos; and in addition there may form a subscale composed of the oxide of the solute element precipitated within the body of the silver. Norbury2 and Leroux and Raub3 have reported internal oxidation (subscale forma¬tion) in alloys of silver with 2, 7.5, and 30 per cent of copper. The presence of the subscale is believed to be responsible, at least in part, for the objectionable "fire mark" in Sterling silver.4 Several other alloys of silver, after oxidizing heat-treatments, are known to exhibit undesirable polishing characteristics that may be the result of internal oxidation. Except for the absence of an external scale of silver oxide, it is to be anticipated that silver alloys will prove to be very similar in their oxidation behavior to the alloys of copper, the oxidation characteristics of which have been studied in some detail5,6 The present research confirms this anticipation. The oxidation of a series of 20 dilute alloys of silver has been studied metallographically; some types of subscale not encountered among the copper alloys have been found. Instances of internal oxidation in alloys of most of the metals of the I-b and VIII groups of the periodic system are on record, but evidence of this type of oxidation in alloys of the metals of the intermediate groups is lacking. A number of the metals of the intermediate group, among them cadmium, lead, tin, and zinc, appear to provide the conditions essential to subscale formation; i.e., they form oxides with a relatively low negative free energy of formation, they dissolve other metals that form more stable oxides, and, presumably, oxygen will diffuse through them. In a study of 4o alloys of these white metals only a few cases of internal oxidation have been found. The probable reasons for this difference in behavior will be discussed presently. EXPERIMENTAL PROCEDURE Silver.-The silver alloys employed in the oxidation studies were prepared in heats of 30 grams each from high-purity silver (99.993 per cent Ag)* and the purest avail-

Jan 1, 1942

By Antonio Augusto Gorni, Kenji Camey, José Herbert Dolabela da Silveira

Recently several studies have been developed on the use of microalloyed steels with low Mn content (below 1%) in the controlled rolling of heavy plates for the manufacture of pipes. However, this novel concept of alloy has peculiarities in its thermomechanical processing. Lower Mn contents should lead to the acceleration of NbCN precipitation kinetics during rolling, leading to a reduction in the soluble Nb content in austenite that delays its recrystallization by drag effect. This fact, plus the heavy and fast passes applied under virtually isothermal conditions in a heavy plate rolling mill with high power, increases the risk of partial recrystallization during the finishing stage of the controlled rolling, since strain hardening of austenite becomes significant and the interaction between precipitation and recrystallization is increasingly delayed. The objective of this study was to analyze the evolution of mean flow stress during the finishing stage of controlled rolling in these low Mn, high Nb microalloyed steels, in order to better understand the metallurgical mechanisms acting during this process and identify conditions that allow full compliance with the requirements of this product class.

Oct 1, 2019

By Ellis Clark

The greater portion of the brown ore in the vicinity of Easton, along the north slope of the Lehigh Mountain or Durham range of hills, is obtained from mines instead of from open cuts or quarries, as is the case in the ore-beds in the western part of Northampton County, in Lehigh County, and in Berks County. The reasons for this method of procedure are various, and the principal causes of the shaft and regular mine system of working being adopted instead of the open air cuts, are: First, the large amount of stripping that would be necessary, as the richer and more valuable portions of the ore do not appear to be found as near the surface as those in other portions of the Kittatinny valley; second, the occurrence of the ore in regular beds, interstratified with the clay, and, to a less extent, in pockets or erratic deposits, as is the case in the mines of Lehigh County; and third, on account of many of the mines being situated at the immediate base of the Lehigh Mountain, where the surface water would be in such large quantities as to be with difficulty handled, and where the subsequent caving in of the sides of the open cut would be almost certain to expose the gneiss rock, which is water-bearing, the large quantities of water coming from which would probably drown out the ore-bed. Shafts, and a regular system of gangways and mining are therefore required by the configuration of the surface, the depth of the deposits and their geological structure. The ordinary size of the shafts is about four feet square, but where an extensive plant of pumping machinery is required the size may be increased to eight feet by six, with two compartments for the hoisting and pump-shaft respectively. A man-way, consisting of ladders with rests at intervals of twenty or thirty feet, is comprised in the pump-shaft, the wire rope being used for purposes of ascent and descent only in exceptional cases, on account of accidents which

Jan 1, 1879