Search Documents

By Carl R. Peterson

The Rapidex continuous drill and blast tunneling concept utilizes a unique spiral blasting pattern that permits efficient performance with relatively small single shots, while at the same time directing major blast fragments at right angles to the tunnel axis. The concept's self-shielding geometry permits the design of a lightly shielded machine that can stay at the tunnel face firing frequent small blasts to provide rapid, virtually continuous advance. This paper describes Phase III of the development program (supported under Bureau of Mines contract H0252047) in which the "front end" of the machine?drilling loading, and shooting components, together with the shield--was fabricated and field tested underground at the White Pine Copper mine, Michigan. One of the major accomplishments of the Phase III effort was to develop a fully remote controlled loading and initiation system in which explosive slurry is pushed, through a hose into the blasthole by a small water-driven piston carrying the blasting cap. The cap is ignited via an induction coil just prior to entry into the borehole, after which a delay permits complete -withdrawal and shielding of the loading hose. The ultimate objective of the present Bureau-sponsored program is to evaluate the feasibility of mechanizing hard rock mining operations, such as development to a point where drilling, loading, shooting, and mucking can proceed simultaneously and result in increased productivity.

Jan 1, 1977

By Synthia N. McIntosh

The U.S. Bureau of Mines investigated the feasibility of using ammonium carbamate (NH2CO2NH4) leaching to recover manganese from steel plant slag. This investigation showed that treatment of the slag in hydrogen prior to leaching enhanced manganese extraction. Up to 80 pct of the manganese and 50 pct of the iron could be extracted from a silicon steel slag that had been pretreated in hydrogen at 700° C. Two 4-h leaching stages conducted at ambient temperature with a solution containing ammonia and carbon dioxide dissolved manganese and iron as their carbamate complexes. Heating the pregnant solution to 65° to 85° C decomposed the complexes and precipitated the metals as insoluble carbonate salts. Ammonium carbamate leaching of other slags from several steelmaking plants produced lower manganese extractions, which suggests that the method cannot be applied satisfactorily to all steelmaking slags

Jan 1, 2010

By Thomas A. Davidson

The Bureau of Mines Helium Field Operations has developed a simple and accurate method for calculating the viscosity of gas mixtures. Only the composition of the mixture and the molecular weights and viscosities of the pure components in the mixture are required. The momentum fraction of a mixture is calculated from the composition. The fluidity is calculated as a quadratic function of the momentum fractions. The efficiency factor for transfer of momentum in collisions between bodies of different masses is derived and used with one empirical constant. The viscosity is the reciprocal of the fluidity. Results of the method are compared with 752 reported viscosities for 40 dilute binary systems at temperatures from -78 to 276.9°C. Using this method the average absolute deviation is 1.29%, the root-mean-square deviation is 1.99%, and the average deviation is -0.84%.

Jan 1, 2010

A mining operation can be identified as demonstrating prudent management when a number of vital characteristics are evident.All risks and opportunities that are critical to the on-going success of the operation have been identified and are being effectively managed. All significant tasks and events are plan driven. All levels of management visibly support the policies of the operation through their attitude, behaviour and actions as well as words. Supporting evidence for required activity and the outcomes is readily available. Improvement mechanisms are working to advance the key business processes. Everyone is working towards satisfying the needs of the stakeholders of the operation. When these characteristics are integrated with the satisfaction of all legislative requirements, all industry codes and optionally all relevant international management system standards then an operation is fulfilling all the requirements of a Due Diligence Process. The majority of mining operations do not show all of these characteristics and therefore unnecessarily suffer from missed profit opportunity and constant cost pressure, less than acceptable safety and health and environmental performance and consequent poor relations with employees, unions and regulators. In these operations the characteristics to be observed are quite different.Serious incidents are occurring with no sign of a rate decrease. The operation lurches from one panic ituation to another. Management are absent in their leadership, but very active in developing rules and enforcement methodologies. The operation has no history. Re-inventing the wheel with employees who come and go at an alarming rate seems to be forever occurring. All efforts are directed at controlling the business outputs with a strong emphasis on blame. Everyone is trying to look busy to avoid the ever-present cost reduction threats. To change to more prudent management utilising a Due Diligence Process is not theoretically difficult. However it does take clear direction, focussed efforts, supporting actions with appropriate tools and perhaps most importantly an internal desire and drive to become such an operation. A Due Diligence Process is about doing the important things that have to be done, providing the understanding of why they are important, demonstrating proof of activity and effectiveness, and leading the way through effective management.

Jan 1, 1998

By John C. Machisak

THE INJURY data and experience at quarries and related plants of the United States are presented in this publication under the following general sections : (A) General injury experience: Tables 1 through 3: Contain current data on the number of injuries, injury-frequency rates, location, accident agency, degree of injury, and related employment data. (B) Injury experience at different kinds of quarries: Tables 4 and 5: Contain current data on number of injuries, injury- frequency rates, location, accident agency, degree of injury, and related employment data. (C) Injury experience by States: Tables 6 through 19: Contain current data on the number of injuries, injury-frequency rates, accident agency, degree of injury, and related employment data.

Jan 1, 1959

By T. S. Grewal, S. C. Gupta, H. Natarajan, T. W. McQuade, N. Nejibulloev-Mamedov

Cigar Lake is one of the world’s largest high-grade uranium mines. The ore mined at Cigar Lake is milled at Orano Canada Inc’s (Orano) McClean Lake mill. The average Cigar Lake ore uranium grade since the start of mining activities in 2014 is 17.8% U (range 8– 28%). To achieve budgeted production of 18 M lbs U3O8/yr the required average feed tonnage to the mill is about 45 kt/yr. Arsenic, occurring as arsenides and sulpharsenides, is one of the major elements of concern associated with Cigar Lake ore. The leaching process is a sulphuric acid leach under oxidizing conditions at near atmospheric pressure. The presence of arsenic in the ore consumes oxidant in leaching as well as ferric sulphate in tailings preparation for arsenic sequestration. The average arsenic grade since the start of mining at Cigar Lake is 0.57% As. Further, the ore is hosted in a matrix of sandstone and clay, which results in poor settling in CCD. The average uranium grade for the balance of Cigar Lake Phase 1 ore is expected to drop to 12.5% U and the average arsenic grade is expected to increase to 1.6 % As, with an annual average peak of 2.5%. Therefore the tonnage throughput required to sustainably meet the production target will increase to 55 kt per year. Orano partnered with Hatch Ltd. (Hatch) to perform a gap analysis study to identify key circuits and equipment in the mill that would require debottlenecking. A METSIM mass balance model of the McClean Lake mill was generated and validated with actual mill operating data. Various feed scenarios were then studied, and the outcome was a traffic light table, which highlighted feed scenarios that exceeded installed capacity of major equipment and circuits. The results provided the basis for the PDC for the pre-feasibility study. This paper will outline the results of the gap analysis, the mass balance model, the feed scenarios and the study undertaken to prepare the McClean Lake mill for the change in ore quality from Cigar Lake.

Jan 1, 2020

By S B. Sheldon

Wall control programs tend to be expensive and consequently require financial justification in order to get approval for the expenditure required. The difficulty faced in getting this approval is that the outcomes of a wall control program are all subjective – a prediction of wall stability and what the wall would do with and without the program. Determining a net benefit is difficult and often justification of a wall control program is based on gut feel, history and a good selling campaign to build a perceived need.This paper outlines a simple solution to this problem by applying risk management principles to wall control. The process is to identify the risks to the operation associated with current wall conditions and then build a risk database for different potential scenarios for each risk. A financial impact is assigned to each risk scenario to complete the database. A consequence and likelihood analysis of each of the risks is undertaken and a formula applied to estimate the projected cost to the operation for the current risk profile. The process is repeated for the predicted wall control conditions after the application of the wall control program. A successful wall control program will reduce an operation’s risk profile so this projected cost should be less than that calculated for the current scenario. The difference in the two projected costs is the value that the wall control program has produced and this value can be used to determine the net financial benefit potential for the wall control program.This methodology can also be applied to other improvement programs that focus on risk reduction such as vibration control.

Nov 8, 2011

By A. B. Young

THERE were produced in this country in 1923 probably in the neighborhood of 12,000 or 13,000 tons of refined and crude arsenic, by far the greater portion coming as a by product of smelting operations. Early this year copper smelters were producing arsenic at the rate of about 425 tons per month and lead smelters at the rate of 7;0 tons per month. During the entire eighteen years prior to 1919, there were produced in the United States only 47,000 tons of arsenic, which amounts to only 25 per cent. of the present output. The great increased demand has come about through the augmented use of arsenates as insecticides and arsenates as weed killers. In an extract from "Mineral Resources of the United States" on "Arsenic in 1922," Messrs. Heikes and Loughlin say, "The minimum possible demand for arsenic in 1923 was estimated at the end of 1922 to be about 13,000 tons, including 2000 tons for plate glass manufacturers, 3000 tons for lead arsenate, 3500 tons for calcium arsenate, 1500 tons for weed killers, 1200 tons for Paris green, 1000 tons for sheep dips and 750 tons for proprietary mixtures. More recent information, however, indicates twice as great a demand for calcium arsenate." The latter has found great use in the last three or four years as a weapon to combat the boll weevil pest of the southern cotton belt. ~t the present writing refined white arsenic is being quoted on the New York market at from 13)d c. to 1455 c. per Ib., while the average price during the eighteen-year period just mentioned was 4.8 c.

Jan 1, 1924

By Robert L. Kranz

The U.S. Bureau of Mines (USBM) has been monitoring and studying seismic activity associated with mining in the Coeur d'Alene silver district of northern Idaho. New statistical methods of studying the stope-scale (1-to l00-m) seismicity at one Idaho silver mine are used in this report (part 1) and its companion (part 2). This report deals with methodology and its limitations. The recent concept of fractals and their seismological use is discussed and applied to mining-induced seismicity. Three types of fractal studies are addressed: spatial analyses (including temporal changes of spatial patterns), temporal analyses, and size analyses. Other statistical measures of mine seismicity are also addressed: event mean location, inter-event distance distribution skewness, temporal coefficient of variation, nearest neighbor and next event statistics, and event location planarity patterns. Each of the methodologies discussed (fractal and nonfractal) is presented using sample data from two stopes in the mine. It is shown that stope-scale, mining-associated microseismicity has a fractal nature. The usefulness of demonstrating fractality (scale invariance) for predictive or descriptive purposes depends on recognition of the factors affecting the calculation of fractal dimensions. Several methodological traps are illustrated that can lead to an incorrect conclusion.

Jan 1, 2010

By Peter J. Szabo

Introduction There has been much said recently about the sophistication of Japanese management in turning out reliable, inexpensive products, such as cars and steel. Techniques include consensus management and quality control circles. These have been touted as prime reasons for inexpensive Japanese products. An often neglected, but major factor in the equation of cheap export goods is the role played by Japanese trading companies. These venerable institutions are a vital factor in Japan's overall strategy of keeping the price of raw materials at the absolute lowest levels. This is critical to the country's economy since the nation must import more than 85% of all its coal. A country that is so desperate for imported raw materials would appear, at first glance, to be at the mercy of its suppliers. In Japan's case, however, the opposite is true. With the exception of brief' windows in 1974-75 and 1980-81, Japan has been in the driver's seat in negotiating contract terms. Due to its dominant role in world coal trade, Japan's situation can be described as a de facto monopsony. By definition, a monopsony is a market situation where the product, in this case coal, is offered by many sellers, but is sought by one buyer. This has been due to the role of Japanese trading companies in dealing with suppliers. Table I depicts trading companies by size in 1982. Mitsubishi and Mitsui are overshadowing in terms of size. The others, though less significant, play a vital role in orchestrating the marketplace. Three critical building blocks on which the strategy of the trading companies are based include intelligence networks, exceptional training of company traders, and shrewd contract negotiation practices. Intelligence Networks All success is derived from these three key components. Of the three blocks, intelligence gathering is the most important. With all the sophistication of the Central Intelligence Agency, the Federal Bureau of Investigation, Interpol, and the Surete', the Japanese trading company's method is every bit as competent and far more gentlemanly. Friendly competition is the key to survival. Although one Japanese trading company appears to be in ardent competition with its rival Japanese trading companies, when studied closely, a totally different picture emerges. The end user nominates certain trading companies as market channels and informally guarantees they will receive compensation regardless of which company wins a specific order. With this concept in mind, the pressure is off. The trading company can aim at getting the best price for the end user. Therefore, bargain, beat, and share information. Do whatever is necessary, but get the lowest price for the end user. Even with the game so gentlemanly, no victory could be assured without an adequate intelligence network. Proper intelligence is only as good as the sources drawn from. But how is one assured of getting the right information? The answer is verification. Verification is comprised of numerous independent sources each cross checked at a central processing unit in Tokyo. Each major Japanese trading company receives input, not only from its own trader, but from other trading companies as well. In addition to their own compilation, trading companies rely on the The Coal Manual, published annually in Tokyo by TEX. This manual covers every major coal producing country. Mines are located and seams identified, mining recovery, equipment lists, washing yield, railway distances

Jan 1, 1985

By Ray E. Harris

A resource of 134,400,000,000 tons of minable trona and mixed trona and halite underlies an area of about 1,300 square miles vest of Green River, Wyoming (Culbertson, in preparation)(Figure 1). In 1982, the total domestic consumption of soda ash (refined trona) was 6,667,000 short tons (Kostick, 1983), approximately 90 percent of which came from Wyoming trona. This enormous resource occurs in the Wilkins Peak Member of the Creen River Formation (Eocene). The Green River Formation is derived from sediments deposited in a large lake (Lake Gosiute) that occupied the Green River Basin in south-western Wyoming 38-54 million years ago. The Wilkins Peak Member represents a restricted, evaporite-rich cycle of deposition during which time the trona deposits were formed. A total of 42 trona beds are known, of which 25 are of sufficient thickness and extent to be considered minable (Culbertson, in preparation).

Jan 1, 1984

By Patrick J. Ryan, Johann F. Kerl, Angelos N. Findikakis

Introduction Tailings disposal methods used by the mining industry include the use of on-land impoundments, surface and underground mine backfill and marine disposal. The latter method, where applicable and under certain circumstances, can be the most economical and best environmental option. The term marine disposal is used to describe deposition of tailings in the open ocean, coastal waters, fjords and inland lakes. A major element in planning and designing a marine outfall is the assessment of its potential environmental impacts. The nature of the disposed tailings, and the physical, chemical, and biological characteristics of the receiving water body must be carefully assessed prior to deciding whether marine disposal is an acceptable option for a particular project. During the last decade, the North American mining industry has demonstrated a commitment to studying potential adverse environmental impacts of marine tailings disposal and to continue monitoring of the receiving waters. Extensive monitoring programs have been undertaken by Canadian mines. Marine tailings disposal is not used in the United States today. One of the largest U.S. mines proposing to use this option is the Quartz Hill mine of U.S. Borax in Southeastern Alaska. To assure the regulatory agencies and the public of the viability and acceptability of this option, U.S. Borax undertook an extensive program of environmental studies aimed at assessing the impact of marine tailings disposal. This program was part of the feasibility and environmental permitting studies conducted by Bechtel Civil & Minerals, Inc, on behalf of U.S. Borax. Due to the unique nature of the proposed tailings disposal system, a Board of Consultants was established. The Board assisted in planning the modeling and field program and reviewed ongoing work. This paper outlines the basic elements of the marine tailings disposal study program which can be viewed as a prototype for similar studies elsewhere. Background The Quartz Hill molybdenum deposit is located on a knoll in an elevated valley in a mountainous region of southeast Alaska, about 45 miles east of Ketchikan (Figure 1).

Jan 1, 1986

By A. L. Murray, C. A. Allen

"The Industrial Commission of Utah from a study of the accidents (especially the fatalities) occurring in connection with mining in the State was struck by the large number arising from lack of due care on the part of the employee injured or carelessness on the part of some fellow employee. Figures show that approximately 40% of the deaths are due to carelessness as against only ) 10% or 12% that can be laid to faulty conditions in the mines. With a view to reducing the number of these accidents an intensive campaign of education was inaugurated, conducted jointly by the Industrial Commission of Utah and the United States Bureau of Mines.Through the cooperation of the U. S. Bureau of Mines, Mine Rescue Car No. 11 operating in Utah has been utilized as the means of carrying on the campaign. In making the regular training visits to the mining camps of Utah the crew of car 11 was authorized to include with the courses of instruction in Mine Rescue and First Aid, safety and health rallies, foremen's safety meetings, and appeals carried on through the public schools to stimulate an awaking of personal responsibility of miners and their familiar' in safety and health endeavor. The work was placed under the direct charge of Dr. Murray who has had previous experience in similar work and brought to the campaign helpful enthusiasm. He was assisted by Bruce Johnson, fore¬man miner of Car 11, who had been safety engineer for the U. S. Smelting Company, and R. W. Clark, first aid miner of Car 11. The expense of providing posters, literature, pledge cars, buttons, rental of special educational films and incidental expenses of foremens' meetings has been born by the Industrial Commission.Plan of the Campaign.In planning the campaign the main object was to revive as much as possible, among the workers, a spirit of responsibility for safety. Any considerable reduction of preventable accidents can be accomplished only through the workers themselves who are responsible for such accidents, therefore, the more personal the application could be made to all the workers the greater the accruing results would be."

May 1, 1921

By C. N. Savage

An industrial minerals review involves an attempt to assemble field and statistical data which are obscure, elusive and incomplete. Often, when me statistical data are available, combining or lumping of commodity values conceals the value of specific items. Personal knowledge of the minerals known to occur in the area of concern, combined with whatever available published data may be compiled, together with careful use of several extrapolation methods, may yield an acceptable summary review of the industry. However, it is particularly hazardous to speculate on future trends and economic aspects because of the many unpredictable variables which may affect the industrial minerals business. Among these variables are the effects of diverse geological conditions, the impact of technological changes (including new uses for minerals not formerly considered industrial types), changing socio-economic factors (including growing environmental controversy), use of substitutes and even recycling of some of the industrial minerals (for example, building materials, lime, etc.). My main objectives are to reveal, as accurately as I can, the state of the in¬dustrial minerals situation, and the effects of possible future developments on this industry in Idaho. Where the words...industrial-tyke minerals, .are used in this discussion, reference is made to selected metallic and nonmetallic minerals and related materials, as well as rock (Table I). Industrial minerals known to be present in Idaho may be listed under general use categories as in Table 1. Some of these commodities are being marketed, have been marketed in the past, or occur in potentially marketable quantities. Mineral fuels are neither mentioned, nor are they considered important in Idaho. Based upon our present knowledge and lack of known, economically valuable occurrences of these commodities, they are considered insignificant (Idaho Bur. Mines and Geology, 1964). Information used for this study is from several sources. Most of the statisti¬cal information should be credited to the U.S. Bureau of Mines Minerals Yearbooks,

Jan 1, 1971

By J Chan, T Baumgartl, A Plante, C Peltre, P D. Erskine

Mine soils are often organic matter and carbon poor due to disturbance, topsoil stockpiling and mixing with spoil. They present an opportunity to observe the accumulation of soil carbon arising from rehabilitation or ‘green carbon’ through organic matter inputs and may be considered for carbon credits. Soil carbon is known to improve multiple soil characteristics and is viewed as an indicator of soil health.When attempting to estimate soil carbon levels in the Australian coal mining regions, both coal and black carbon (BC) need to be quantified. Coalmine soils contain coal particles that are difficult to distinguish from organic matter using standard carbon analyses. BC, a material arising from the incomplete combustion of organic matter and fossil fuels, displays some similar characteristics to coal and is ubiquitous in Australian soils due to bushfires. The presence of coal and BC complicate the determination of green carbon levels in mine soils.A method to quantify coal and BC in mine soils from the Bowen Basin using thermal analysis and multivariate curve resolution is presented. By determining BC and coal contributions it is then possible to calculate green carbon levels in rehabilitated mine soils. Calculated green carbon levels are compared with bulk density as soil quality indicators.CITATION:Chan, J, Baumgartl, T, Erskine, P D, Peltre, C and Plante, A, 2014. Distinguishing carbon fractions in coalmine rehabilitated soils, in Proceedings Life-of-Mine 2014 , pp 491–498 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Walter C. Labys

There has been considerable growth in public enterprise institutions involved in mineral commodity markets. These institutions typically consist of trading organizations (STO1s), regulatory agencies, and mixed agencies. The particular character of these institutions varies according to whether they reside in developing countries, in Eastern Europe (COMECON Countries), in industrialized countries, or in the form of international agencies. The purpose of this paper is to explain recent attempts to assess the growth of public enterprises as well as their impacts on mineral markets and trade. Some earlier analyses of market impact made by the author have been up- dated for four major mineral markets: copper, tin, bauxite and iron ore. Conclusions are drawn regarding the dynamics of market structure changes and their impacts.

Jan 1, 1986

By P. C. McWilliams

Researchers at the U.S. Bureau of Mines investigated the use of close-range photogrammetry and subsequent stereo digitizing to obtain data from rock fracture roughness profiles. The photogrammetric process yielded results that were acceptable but somewhat inferior to those obtained by a mechanical profilometer. On the basis of this study, further pursuit of photogrammetry as a data collection method in mining is proposed. Fractal geometry was investigated as a means of measuring the roughness of rock fracture profiles. Four fractal algorithms were used: divider method, modified divider method, box method, and spectral method. A comparison of the methods gave ambiguous results. Brown's modified divider method provided the best means of obtaining the fractal dimension. Shear strength estimates were obtained using the parameters of the modified divider method and Myers' Z2 measure. Because of differences in results when comparing the different ways of obtaining the fractal dimension, future users of fractals in studies of rock fractures are advised to cross-check their results carefully.

Jan 1, 2010

By Dolf Gielen

This paper discusses the results of a Western European energy and materials systems engineering study that analyses the impact of greenhouse gas (GHG) emission reduction on the future of the steel and aluminum industry. he technology selection will be significantly affected by future CO2 policies. The avail- ability of C02 removal and storage technology and the social acceptance of this strategy for GHG emission reduction is of key importance for the strategy selection. The use of coal based smelting reduction technologies is optimal in case of weak C02 policies or in case of strong C02 policies and low CO2 removal and storage costs. The selection of CCF or Corex technology depends on the penalty regime. However, if C02 removal proves to be problematic, CCF development fails and strong C02 policies are introduced, the gas based DRI production processes will become more attractive. In both cases, the energy efficiency of the iron and steel industry will further increase in the next decades. The impact of GHG emission reduction on aluminum prices and aluminum use can be significant. However contrary to common notions the aluminum production will be positively affected by GHG emission reduction, notwithstanding the currently high emissions in aluminum production. A combination of emission mitigation in production and significant GHG emission reduction effects further down the product chain cause this effect. A significant potential exists for improved materials efficiency. This potential is generally neglected in energy efficiency and CO2 reduction studies. However improved steel qualities are of similar importance for C02 emission reduction as increased energy efficiency. It remains to see if this potential will be used to its full extent in the next decades. Model calculations indicate that the impact of C02 policies on the competition with other materials will be limited. Greenhouse gas emission mitigation will have much more impact on materials production and waste handling than on materials consumption.

Jan 1, 1999

By Karl J. C. Harries

"1.1. WHAT ARE AGREEMENTS AND HOW ARE THEY FORMED?In order to have an agreement, at common law, there must be an offer, acceptance of that offer, and consideration passing between the parties. In addition, the material terms (i.e. the basics or substance) of the agreement must be discernible, preferably by means of documentation. Although these concepts may appear simple and straightforward, the law relating to them is voluminous and complex. Some brief comments are worthwhile.• Offer/acceptance: Both offer and acceptance should be in writing, but they need not be. The actions, conversations, and/or correspondence of the parties may constitute either or both of them. Notwithstanding, the local law or practice of a jurisdiction will impose some specific requirements for certain types of agreements. If these requirements are not met, the agreement may be unenforceable. For example, Ontario’s Mining Act requires transfers of unpatented mining claims to be evidenced in writing and recorded.1• Consideration: Consideration is usually thought of as being money, but it can be virtually anything, even “the premises” (i.e. the mutual covenants or promises contained in the agreement itself). In addition, if one party, relying upon the offer of another, does something to his detriment, then the doing of the act can be considered to be an acceptance of the offer and, under the legal concept of “detrimental reliance”, can also be consideration. Whether or not detrimental reliance exists will depend upon the circumstances of each case.2• Material terms: The requirement that the material terms of an agreement must be discernible does not mean that all of the terms of an agreement must be documented or even have been considered, just the basic or material ones. In addition, it will be up to a judge to decide what is material – not necessarily the parties. In order to establish the material terms, a Court may look at all relevant documentation and may hear oral evidence. It will resist “writing the agreement”"

Jan 1, 2003

By D. E. Shanks

This U.S. Bureau of Mines (USBM) research simplified an earlier hydrogen chloride (HCI) leach-sparge process developed by the USBM to recover reduction-grade alumina from domestic kaolin clay. Improvements were made by decreasing the initial leaching acid concentration from 25 to 20 pet, decreasing the leaching time from 1 to 2 h to 15 to 30 min, eliminating the solvent extraction step for Fe removal, and eliminating the step to recover the AI content of the bleedstream circuit. A 10-cycle bench-scale experiment of the simplified process showed that the ferric chloride (FeC13) concentration built up to 9.3 g/L in the recycle stream. This did not interfere with any of the unit operations or final alumina product purity because Fe forms stable soluble chloride complexes when sparged with HCI and is easily washed from the large aluminum chloride hexahydrate (ACH) crystals. The reduced leaching time and acid concentration did not decrease Al extraction.

Jan 1, 2010