Search Documents

By Y. Mudryk, D. Paudyal, K. A. Gschneidner, V. K. Pecharsky, M. Khan

"Rare earth intermetallic compounds are utilized commercially as magnetic and battery materials, electron gun electrodes, etc. Several of these intermetallics will be briefly discussed. There are many other rare earth intermetallic compounds which are not utilized industrially but have unusual properties which are of fundamental interest and may have future technological applications. Several of these materials are discussed as well.INTRODUCTIONTens of thousands of rare earth intermetallic compounds exist, but physical properties (primarily their magnetic behaviors), other than their crystal structures have been measured for only a small percentage of these materials. Among these are the commercially important compounds: Nd2Fe14B, and the SmCo5 – Sm2Co17 family – well known high strength permanent magnets; (Tb0.3Dy0.7)Fe2, Terfenol-D, a giant magnetostrictive material; LaNi5Hx a critical component of the rechargeable Ni metal hydride batteries; and LaB6 an electron emitter. There are, however, many other intermetallic compounds which are not utilized industrially, but none-the-less, exhibit interesting, and sometimes, exotic physical properties which are of fundamental interest and may have some future technological significance. These include: the giant magnetocaloric effect compounds Gd5Si2Ge2 and La(Fe13-xSix)Hy; the RCu and RAg families of ductile intermetallics; the mixed intra-lanthanide (R,R')Al2 compounds in which magnetic transitions disappear and reappear as one R is substituted for by R'; and GdNi which exhibits large dilations along two crystallographic directions and a larger contraction in the third direction at the Curie temperature resulting in zero volume change as GdNi orders magnetically via a second order phase transition.COMMERCIALLY IMPORTANT INTERMETALLICSNdFeB Permanent MagnetsThe Nd2Fe14B permanent magnets were discovered in 1984 independently in the USA and Japan. It is a ferromagnet and with proper heat treatment and processing Nd2Fe14B is the strongest near room temperature permanent magnetic material known today. This intermetallic compound is utilized as a permanent magnet in many applications, such as electric motors (e.g. the modern automobile contains up to 35 electric motors), spindles for computer hard disc drives, microphones and speaker magnets for cell phones and other audio equipment, direct drive wind turbines, actuators, and Magnetic Resonance Imaging (MRI) units. There are two kinds of NdFeB permanent magnets – bonded and sintered. The bonded magnets have a lower magnetic strength than the sintered magnet. The highest strength magnets are obtained by small substitutions of Dy (up to a maximum of 10%) for Nd, because Dy can significantly increase the coercivity and thus the energy product (a measure of the magnetic strength or hardness). The bonded magnets account for about 12% of the NdFeB market (~82 metric kt per year, containing ~20 kt/a of Nd). The NdFeB permanent magnet market is growing at a rate of about 15% per year. (Burzo & Kirchmayr, 1989; Kobayashi & Hirosawa, 2001; Coey, 2011)."

Jan 1, 2012

By N. Jovanovic, A. Vazirizadeh

"The main objective of this study is to find a solution to design a mass flow observer system with the minimum required sensors and maximum observability for a mineral processing plant. The second objective is designing a mass flow observer configuration with high reliability to manage sensor failures. This configuration will provide a robust monitoring system that increases plant availability and process measurement fault detection. Furthermore, the monitoring system is expected to improve process efficiency. In this investigation, the procedure of designing an observer system is presented along with three models to design the sensor network. The advantages and disadvantages of each models are discussed and finally the models result for an industrial case are presented and analyzed. INTRODUCTION The concepts of observability and redundancy of mass flow are directly linked with the ability to solve and estimate the mass flow. There are hundreds of streams in a process plant flowsheet, and for technical and economic reasons it is not possible to measure all mass flows. It is thus important to know for a set of measured streams, which of the unmeasured streams can be estimated. The concept of observability deals with this issue. It is also valuable to know whether a measured mass flow of streams can be estimated even if a sensor fails for some reason. Redundancy deals with this failure question. A stream is said to be observable if it can be estimated by using the measurements and/ or mass conservation equations. Also, a stream is redundant if it is observable even when its measurement is removed. Observability and redundancy analysis can be exploited for adding new measuring instruments. It can also play a useful role in efficient decomposition and data reconciliation problem (Narasimhan and Jordache 1999). The value of an observer system cannot be justified without considering its benefits. This justification is done through evaluation of data reconciliation, gross error detection and improving process performance such as outlined below:"

Jan 1, 2018

By Manoj Khandelwal, Minghui Liu, Jian Zhou, Kun Du

The waste rock and tailings backfill into the mined-out areas are the most effective method for solving the environmental pollution and surface disasters for nonferrous metals mines. In practice, the success and availability of backfill operations are dependent on the slurry fluidity and the strength properties of cement backfill. The transport of the slurry through the pipeline to the designated backfilling area relies on its eximious flow properties, while the appropriate strength of the filling body ensures the safe operation of the stope. In this paper, the effects of cement and aggregate types on the slurry fluidity and strength characteristics of cemented backfill are studied in detail, which are often ignored in other pieces of literature. Diffusivity is used as an indicator to evaluate the slurry fluidity. Various slurries whose concentrations ranging from 70%, 73%, 75%, 78%, and 80% are made with different aggregate ratios and cement-sand ratios are tested. It has been shown that slurry fluidity is inversely related to its concentration, but 78% is the “stopping point” for the deterioration of fluidity. The addition of rod-milled sand improves or worsens the cemented backfill (CB) strength depending on the amount of rob-milled sand. The uniaxial compression experiment results on 216 CB specimens produced by different combinations of influencing variables showed that CB specimens made from cement with superior mechanical properties have a higher uniaxial compressive strength (σucs). It has been also found that the effect of aggregate ratio on the CB strength is not singular, but works in conjunction with the curing time and the cement-sand ratio. The longer the curing time and the higher the cement content, the higher the CB’s σucs. To avoid the time-consuming and costly problem of obtaining the strength of the CB from indoor experiments, an SVR model capable of predicting the uniaxial compression strength of CB specimens is proposed, which is optimized by genetic algorithm (GA) and particle swarm optimization (PSO) algorithm. The results of the three performance indexes (MAPE, MSE, and R2) show the superior performance of the GA-SVR and PSO-SVR models and the agreement of the predicted results with the experimental results, which indicate that these two models can accurately predict the σucs of CB.

Feb 3, 2022

By A. Jahedsaravani, M. Massinaei, M. Zarie

Deep learning is a subset of machine learning that uses artificial neural networks for extracting high-level features from image data. In the present study, a soft sensor is proposed for the prediction of the flotation performance through froth features generated by the use of pre-trained convolutional neural networks. Several state-of-the-art convolutional neural networks (AlexNet, GoogLeNet, VGGNet, ResNet, and SqueezeNet) pre-trained on the ImageNet database are used to predict the metallurgical performance of two flotation systems. The first case study is a batch copper flotation system video-captured over a wide range of process conditions. The second case study is an industrial coal flotation column equipped with a continuous video recording system. The pre-trained networks are used to extract features from the froth images, and these features are subsequently used to predict the flotation conditions and performance. The prediction results by the pre-trained algorithms were compared with the traditional image processing algorithms. This demonstrates the ability of the pre-trained structures to generalize to images outside the ImageNet database. GoogLeNet outperforms other network architectures and provides more accurate predictions of the flotation process behavior and performance.

May 5, 2023

By S. P. Lowe

Flotation testing of Flin Flon ore was started in the Denver laboratory of Complex Ores Recoveries Co. in March, 1926. There had been a considerable amount of flotation testing previously which had shown possibilities of success, and it was felt that, with the increased knowledge of flotation and the comparatively new reagents then available, flotation held out the best prospects for a successful commercial treatment of this ore. There remained available for this experimental work a small amount of the rejects from a thorough sampling of the mine and some ore from the mine dump.

Jan 1, 1930

By T Vijayakumar, Vipul Dobhada, Rajesh Patel, Swarnadip Dey, Naveen Babu D

The most challenging scope of any bridge project in marine or inter tidal zone is to construct sub structure like well Foundation, group pile, pile cap etc. Similarly, it also affects the marine environment/ecology to a great extent. Understanding the level of difficulties and aiding to provide an environment friendly solution, various options are analysed to overcome these and found mono pile to be the best alternative in this context. Generally, the foundation type of any bridge constructed in river, marine or intertidal zone in India is preferred for group piles. For the first time, monopile is being accepted as the foundation of bridge in India at Mumbai Coastal Road Project. The diameters of the monopiles used in this project are 2.5 m and 3.2 m. Hence, the challenges involved in monopile construction and experiences to overcome it are worth to share. Here, a brief discussion on environmental, geological issues and the needs of monopile as the foundation of bridge has been discussed. Furthermore, the monopile construction stages and confirmation of monopile capacity through different load tests have been elaborated.

Sep 1, 2022

By J. Clark

The objective of this study has been to determine the state of the art in underground, thin-seam-mining systems, to identify new technology and procedures that would reduce the hazards of thin-seam mining and to recommend areas for further research. The study was carried out in two phases, the first of these being devoted to a survey of authoritative literature. Subsequently, the practices adopted in the various mining countries were analysed and comparisons made to identify machines and methods with the potential for application in the USA. Published figures on US bituminous coal reserves show the high proportion contained in thin seams and US accident statistics demonstrate that the risk is greater in thin-seam operations. A comparison has been made with the experiences of foreign operations. The Phase 11 study proceeded along two separate avenues to examine the distinctive problems associated with seam thicknesses above and below 30 in. Current systems of mining appropriate to seams greater than 30 in were elaborated and compared by means of a simulation exercise in terms of safety, production and cost. For seams below 30 in, less conventional systems, some presently disused, were studied and their potential evaluated; the research and development work necessary to make them viable has been indicated.

Jan 1, 1980

By M Badawi, Y Foucaud, C Veloso, J Laine, A C. Araujo

Iron is one of the most exchanged commodities worldwide. Its use for steelmaking explains the growing demand in the metal which remains mainly produced by the mining and the beneficiation of iron ores. Flotation is the most used mineral separation technique worldwide, processing several billion tonnes (Bt) of ore annually, including, in some cases, hematite and magnetite ores. Based on the physicalchemical properties of mineral surfaces, flotation aims to selectively adsorb molecules that render mineral surfaces either hydrophobic or hydrophilic, known as collectors and depressants, respectively. Hydrophobic particles are then recovered in the froth by the injection of gas bubbles travelling up in the cell and attaching the hydrophobic particles. However, despite the popularity and the good performances of flotation, mining industry faces new challenges of decreasing grades and increased mineralogical complexness in ores. Many flotation variables, especially when related to reagent adsorption, remain poorly understood and it becomes necessary to gain knowledge to enhance the existing processes. Molecular modelling techniques like the density functional theory or molecular dynamics simulations (ie Classical molecular dynamics or Ab initio Molecular Dynamics) currently represent powerful tools for different applications in material sciences, like catalysis or depollution purposes. They have recently been successfully applied in the flotation area, with an increasing number of publications dealing with this topic every year. These tools provide crucial information on bulk and surface properties as well as on the adsorption mechanisms of reagents on mineral surfaces, key step in the flotation process, and synergetic effect of collector mixtures. A better understanding of the adsorption mechanisms of flotation reagents, provided by molecular simulations, will help to finely choose flotation reagents, and even lead to the development of new reagents formulations. Overall, these tools enable the discovery of practical and industrial solutions to improve the flotation process, which will undoubtedly help the mining industry to face its future challenges.

Nov 8, 2021

By Forrest T. Moyer

All general measures of the safety record of the coal mining industry worsened appreciably in 1970. Injury experience for the year was 260 fatal and 11,552 nonfatal injuries at respective frequency rates of 1.00 and 44.40 per million man-hours of worktime. The fatality total was 57 higher and the rate of occurrence was 18 percent higher than the corresponding figures of 203 fatal injuries with a frequency rate of 0.85 in 1969. The worsened fatality record in 1970 resulted primarily from a major disaster (a single accident which results in the death of five men or more) on December 30, 1970, that killed 38 men. There were no major disasters in 1969. The total of 11,552 nonfatal injuries in 1970 was the highest annual total since 1960. It was 1,635 higher and the frequency rate was 6 percent higher than the corresponding totals for 1969 of 9,917 nonfatal injuries occurring at a rate of 41.76. The injury severity rate of 8,308 days lost or charged per million man-hours was 13 percent worse than that of 7,359 in 1969. Similarly, the average severity of 183 days lost or charged per injury in 1970 was 10 days or 6 percent higher than in 1969. Aggregate worktime of 260.2 million man-hours and production of 609.8 million tons in 1970 were, respectively, 10 and 7 percent higher than in 1969. An average of 144,480 men were at work on an average of 227 active days in 6,316 mines and 544 mechanical cleaning plants during 1970.

Jan 1, 1973

By Lance Rasband, Richard Hanke, John Starcevich

"The 17.4 meter (57 ft) diameter tunnel boring machine (TBM), the world’s largest at the time of her launch in 2012, locally referred to as “Bertha,” is stuck. Incapacitated due to mechanical failure approximately 36 meters (120 ft) beneath downtown Seattle, situated precariously between the deteriorating Alaskan Way Viaduct and the failing Seattle Seawall. Accessing Bertha with a vertical shaft provides the best approach to address all facets needed for repairs and will allow the full removal of Bertha’s cutter head and related inner workings. Limited area above the tunnel alignment and the physical restrictions of existing infrastructure, create significant challenges for the design of an otherwise symmetrical shaft, requiring special attention to design and layout. Consequently, the access/recovery shaft design required a combination of 3m, 2.5m, 2.2m, 1.5m and 1m diameter unreinforced drilled secant piles coupled with various ground improvement techniques and dewatering, to fully satisfy the shoring design requirements. This paper will describe the shaft installation procedures, equipment used and pitfalls encountered while undertaking access shaft construction of this magnitude.INTRODUCTIONTunneling on Seattle’s SR99 tunnel project began in July of 2013. After slowly mining through a 4.5 m (14.76 ft) thick fiber-reinforced concrete headwall and the first of three stabilized “safe havens,” Bertha would proceed along the proposed alignment through 122 meters (400 ft) of jet grout improved soil at a rate of slightly over 1.6 m (5.25 ft) per day. Once past the improved area, it was planned that “Bertha” – would be moving at a rate of about 11 m (36 ft) per day. By the end of October 2013, Bertha had mined roughly 131 m, (430 ft) averaging 1.4 m (4.6 ft) per day and had begun mining within native soils. By December 2013, tunneling had reached the 244 m mark and Bertha was averaging 3.6 m (11.8 ft) per day, achieving as much as 12.8 m (42 ft) of progress on given days. Unfortunately, on December 6th, 2013, Bertha began to stumble and all progress quickly came to a halt.It was initially reported that an obstruction had stopped Bertha in her tracks. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic pressure around the TBM, and allow visual inspection of the cutter head from within the TBM, and also to investigate for the presence of obstructions at the face of the cutter head. During this inspection, fragments of steel pipe were discovered entangled in the cutter head. The fragments were apparently from an abandoned 254 mm (10 in.) diameter monitoring well casing, previously installed by WSDOT to monitor ground water conditions for the design and planning of this tunnel project. After the steel was removed from the cutter head and cleared from Bertha’s path, tunneling resumed. It was then discovered that Bertha was only able to generate a slow crawl."

Jan 1, 2016

By W. M. G. Heeley

In the province of Alberta the coal measures dip at so many different angles, between the horizontal and the vertical, that many different systems of haulage are in use. I will, however, only touch briefly upon the general -systems in use, and devote the major portion of this paper to a discussion of endless-rope haulage and its adaptibility to various conditions in coal mines; dealing in particular with the endless-rope haulage that was installed at Brule during the month of August 1923. In coal seams that are approximately level, and newly opened, hand-putting or tramming from the face is the cheapest, but when the mine is further developed tramming is out of the question, and the use of ponies is the next consideration. The time arrives, however, when mining reaches a point where the economical haulage of coal by horses cannot be done profitably, and then some system of mechanical haulage must be installed. The installation of any system should be carefully considered before any particular type of haulage is adopted, because a great deal depends upon the grade or dip of the seam. Motor haulage is impossible to operate profitably on a grade of over 6 per cent and, while it is possible to use ponies, on short runs, up to 9 per cent, some other means of main and secondary haulage must be installed when a 9 per cent grade, is exceeded. I will, therefore, deal first with secondary haulage, because even though a main haulage is established, secondary haulage can be used to feed the main haulage.

Jan 1, 1925

By Yael Miron

Coal mines that undergo self-heatings, and specifically mines that sustain both floor heave and self-heatings, would benefit from the use of sealants to minimize air ingress to susceptible areas. The U.S. Bureau of Mines (USBM) evaluated three sealant systems for this purpose, bentonite-water mixtures, silicate gel, and guar gum gel. The guar gum-based gel was the only sealant that possessed the desired properties of elasticity, ease of preparation, adaptability to the mine, and a long life. In addition, since the gel consists mostly of water, it could quench or cool nearby heatings. Optimal formulations were determined in laboratory tests, and then tested in the USBM Safety Research Coal Mine. Two for-mulations resulted in stable gels that lasted for at least 12 months in the mine. Semicontinuous preparation of gel using an eductor was evaluated and appears feasible. Although guar gum gel is expensive, selective use to prevent heatings in specific areas would be cost-effective, both in terms of productivity and enhanced mine safety.

Jan 1, 2010

By Graham W. Marks

The general positions of the absorption maxima of aqueous solutions of the violet and green isomers of chromic sulfate the visible spectral region have long been known, but, to the knowledge of the writer, no comprehensive studies have ever been made. To gain further knowledge concerning these inorganic complexes and to investigate the possibilities of developing an analytical method for determining the concentrations of the violet and green isomers in a mixture, a more complete investigation was made in the spectral range from 325 to 850 millimicrons.

Jan 1, 1951

By Fangyu Liu

In the grand tapestry of scientific inquiry, there are individuals whose contributions resonate far beyond the confines of laboratories and lecture halls. It is with profound admiration and respect that we present this special collection of Mining, Metallurgy & Exploration, dedicated to celebrating the remarkable career of Dr. Patrick Taylor. Dr. Taylor, recently retired from the Colorado School of Mines as the Emeritus Ansell Distinguished Professor of Chemical Engineering, possesses over 45 years of expertise in mineral processing and extractive metallurgy. His remarkable journey has seen him traversing the globe, from Canada to Egypt, contributing to pyrometallurgy, hydrometallurgy, and mineral processing. Dr. Taylor’s portfolio encompasses lab work, pilot-plant projects, research, and process development across various metals, with an impressive array of authored papers, presentations, and nine patents to his name. A soughtafter consultant for over 20 companies and an esteemed expert witness, Dr. Taylor also led the Kroll Institute for Extractive Metallurgy at Colorado School of Mines. Under his guidance, more than 100 graduate students and post-docs have undertaken transformative research, while Dr. Taylor’s 45-year tenure as a university lecturer and the creation of 10 industryfocused short courses underscore his dedication to knowledge dissemination. His contributions extend to crafting professional engineering exam questions for a quarter-century and active participation in esteemed organizations like SME, TMS, ASM, and MMSA.

Sep 16, 2023

By R. R. French

The industrial minerals industry in the Atlanta, Ga., area was studied in order to better understand problems associated with exploiting mineral resources in and near metropolitan areas. A method for delineating the Atlanta urban area and its component parts was developed so that the factors affecting the location of the minerals industry could be viewed mere objectively in the urban context. Major attention is focused on the area's dominant crushed stone subindustry Demographic and socioeconomic analysis of the Atlanta, Ga., area shows that expansion of the metropolis and its environs will probably eliminate potential mineral resources from the mineral resource base in the area, and that the expanding metropolis will be the primary determinant of future mining sites. Competition for land is accentuated to varying degrees by the incompatibility of wining operations with residential and other environmental requirements. Areas of consideration are suggested to provide maximum development of land and resources for greatest economic benefits it minimum social cost. Further research is recommended to determine market locations in urban areas, optimum operating levels for industrial minerals plants, and alternatives to surface mining.

Jan 1, 1970

By C. A. Born

AMAX Inc. climax's mine-mill complex at Climax, Colorado is best known for its molybdenite production: 50,000 TPY of molybdenite flotation concentrate (95% MoS2) from mill heads containing 0.35% molybdenite. Less recognized are the byproducts that are concentrated from the tails generated in the rougher flotation circuit (see Figure 1). Climax recovers a heavy mineral concentrate by passing the rougher tailings from molybdenite flotation over Humphrey spirals (Figure 2a). This concentrate is floated using xanthate at pH 4 to remove sulfides, principally pyrite. The tails from the pyrite float are then cleaned of quartz, feldspar and light minerals by tabling (Figure 2b). Amine flotation follows at pH 1.5 and 75°C to float monazite (Figure 2c). The present circuit at Climax dries the monazite flotation tailings and utilizes high intensity cross-belt magnetic separation Figure 2d) to generate a high grade wolframite concentrate and a low-grade cassiterite product, both of which are contaminated with the mineral brannerite, (UO, TiO, UO2)TiO3. The uranium specifications have recently become difficult to meet due to the increasing percentage of brannerite reporting in the mill feed. A plant is being built utilizing hot sulfuric acid and sodium chlorate to leach this uranium from the monazite flotation tailings prior to their being fed to the wolframite- cassiterite magnetic separators. This modification is the subject of our paper.

Jan 1, 1975

By W. L. EGY, GEORGES. RICE, L. M. JONES, J. K. CLEMENT

This report has been prepared, not only for the purpose of recording the results of the first series of coal-dust tests conducted in the experimental mine of the Bureau of Mines, but also to place before the mining public a description of the mine and an account of the objects sought in its establishment. Soon after the organization of the technologic branch of the United States Geological Survey, J. A. Holmes, then chief of the branch, concluded that for the solution of various problems relating to the causes and prevention of mine explosions it would be best to carry on large-scale tests in a mine rather than in a surface gallery. The idea of utilizing the underground passage of a mine for making explosion experiments did not at' first meet with general approval among investigators in this country or abroad. Many thought a mine passage was not a proper place in which scientific tests could be conducted, as great difficulty in controlling conditions was expected. However, after all arguments for and against such an investigation had been carefully considered, plans for opening an experimental mine were definitely adopted by the Bureau of Mines in 1910, and an allotment of funds was made to carry out the project. The first endeavor was to find an existing mine suitable for the purpose, but the mines offered by owners were either worked out, were wet, had poor roofs, or presented complications of various kinds, so that it was finally decided to open a mine if a site could be obtained having natural conditions that would fill the various requirements. A most desirable location was found on property of the Pittsburgh Coal Co., near Bruceton, Pa. The president of this company, Mr. W. K. Field, the general manager, Mr. G. W. Schluederberg, and the chief engineer, Mr. E. J. Taylor, rendered every possible service in

Jan 1, 1913

By David Porter, Nathan Rouse

The implementation of presplit perimeter control in underground mining as a method to decrease dilution yields positive benefits throughout the current and future mining cycles. A case study to understand the benefits of reducing overbreak and underbreak in a cut and fill mining cycle was performed to quantify the reduction in backbreak. The study was performed in a control section of the mine where a presplit perimeter control design was utilized for a length of heading. This control heading was then compared to the existing standard blasting design within the same mining zone. The comparison included multiple aspects of the mining advance including overbreak, dilution of waste, dilution of Cemented Rock Fill, bolt counts, and cycle times. Once mining in the control section was completed and mining commenced in adjacent headings, blast damage due to blast design could be quantified.

Feb 6, 2023

By Krishna P. Sinha

An investigation was made to determine the creep behavior of oil shale at elevated temperatures. During the first phase of the investigation, work done on creep behavior of geologic materials was reviewed and triaxial creep tests on oil shale were planned. Tests at temperatures up to 250°C and axial stress up to 3000 psi were conducted at no confinement and at confining pressures equal to 1/3 and 2/3 of axial stress. Wide variations in the elastic properties as well as creep characteristics are exhibited. Creep deformation is more pronounced at elevated temperature but no definite quantitative remarks can be made regarding effect of grade of oil shale due to wide scatter and limited number of data paints. Primary creep can be described by a power law. Secondary creep seems to be an experimental function of deviatoric stress. Teritary creep was not observed within the test duration (24 hours in most tests).

Jan 1, 1983

By Tchingis Lekhatinov, Lev Filippov, Vyacheslav Severov, Alexandre Matinin, Victor Samyguin, Inna Filippova

"Comparison of flotation efficiency of the new multi-zone flotation cell (MZFC) and different conventional cells was carried out at lab and pilot scales on the various samples: high contrast pyrite tailings and old copper containing tailings. MZFC is a cell of intensive flotation, which provides optimal hydrodynamic conditions for all flotation sub processes. Enhancing of particle attachment, creation of conditions for coalescent flotation, selection of spatially separated zones according to optimal hydrodynamic conditions for flotation sub-processes are proposed as main principles to design an MZFC. The bubbles/pulp stratification was pointed out as a limiting step in the existing intensive flotation machines. Two strategies to improve bubbles/pulp stratification in the MZFC were studied: (a) impact of pulp-bubble jet to the surface of a prismatic insert inside of cell, which provides the detachment of low hydrophobic particles from bubbles, and (b) profiling the pulp/bubbles jet from the reactors due to a specific geometry of cell walls. The new continuous MZFC devices were demonstrated similar or higher efficiency in comparison with laboratory batch flotation cells for pyrite flotation. Higher flotation efficiency (82%) with pure pyrite concentrate (51.2% of sulfur) and a recovery level of 92% was obtained in MZFC when the cell with stratification by impact was used. Similar results were obtained with old Cu-containing tailings. Although MZFC had 1.5 times greater yields of concentrate than a batch flotation cell, it provided the increase of chalcopyrite recovery by 29.4% and concentrate grade by 4.8%. An original organization of pulp/bubbles stratification in the separator part of the new intensive flotation machine using variable geometry inserts allowed the best flotation selectivity with a bubble mineral loading coefficient 1.5 fold higher than the laboratory mechanical or pilot cells."

Jan 1, 2014