Search Documents

By Janusz S. Laskowski

The flotation-related properties of hexanol derivatives and mono-alkyl ethers of propylene oxide, which include many important flotation frothers (e.g. MIBC, DF-200, DF-250, DF-1012, etc.) have been studied. The obtained results show that the DFI (Dynamic Foamability Index) - CCC (Critical Coalescence Concentration) plot can be used to classify flotation frothers. The frothers characterized by low CCC and high DFI values have properties of strong flotation frothers, while those with high CCC and low DFI values are more selective. The proposed frother classification system, based on simple CCC and DFI measurements, provides, for the first time, a solid ground-work for characterization of the flotation frothers.

Jan 1, 2003

By D. Harrington

This paper is a revision of Information Circular 7380, by D. Harrington and J. H. East, Jr., published in 1946, entitled ?Safe Storage, Handling, and Use of Commercial Explosives in Metal Mines, Nonmetallic Mines, and Quarries.? Issued soon after the close of World War II, this earlier circular described the unprecedented increase in the production and use of commercial explosives during the war as a result of expanded industry and the tremendous demand f or metals and minerals. In the years following World War II, the production and use of commercial explosives in the United States have continued to rise. Hence, the Bureau of Mines presents these revised figures through 1952. In rewriting this Wormation circular, most of the text prepared by Harrington and East has been retained, with newer statistical information compiled by Seth T. Reese, Accident Analysis Branch, and V. E. Wrenn, of the same branch.

Jan 1, 1954

By Alan de Sousa

O presente trabalho tem por objetivo revisar o atual plano de lubrificação de um laminador a frio modelo Sendzimir, tendo como foco principal determinar por meios analíticos, a confiabilidade dos processos de relubrificação à graxa de mancais de rolamento. Para a determinação dos parâmetros de relubrificação do restante dos conjuntos, que não são mancais de rolamento, foi realizada a consulta dos catálogos dos fabricantes para a determinação dos intervalos e quantidades, conforme recomendação destes. Para a realização deste trabalho, foi necessária uma extensa revisão bibliográfica, de normas e literaturas referentes a este tema. No final deste, objetiva-se a obtenção de um aumento da confiabilidade dos equipamentos, além de uma redução de custo com mão de obra e lubrificante durante os períodos de relubrificação.

Oct 30, 2017

By Eduardo Spinelli Oliveira

Devido à possibilidade de se remover quantidades muito pequenas de material de cada vez, a ablação seletiva por laser tem se mostrado um método muito eficaz para remoção de finas camadas de materiais depositados sobre um substrato. Neste trabalho, um laser de femtossegundo foi utilizado para remoção de um filme fino de nitreto de titânio (TiN) depositado sobre um substrato de carboneto de tungstênio (WC), configuração comum em pastilhas de usinagem mecânica, objetivando fornecer um método eficiente para tal processo. Os limiares de ablação do filme e do substrato foram determinados, evidenciando a problemática do trabalho, remover um filme com limiar maior que o substrato. Um sistema de controle de espectrometria de emissão atômica induzida por laser (LIBS) foi testada, com a intenção de controlar em tempo real, a espécie do material ablacionado, mostrando-se muito eficiente. Os parâmetros do laser bem como da varredura de usinagem ainda estão sendo testados para definir a viabilidade do processo.

Aug 17, 2017

By Natalie Chaves de Siqueira

Aços inoxidáveis austeníticos fundidos por centrifugação, da classe HP, são comumente utilizados na indústria de óleo e gás para a fabricação de tubos usados em fornos de reforma e pirólise. Essas ligas possuem uma elevada resistência à oxidação, elevada estabilidade térmica e elevada resistência à fluência em altas temperaturas, sendo esses requisitos necessários para aplicação nos fornos. Mudanças microestruturais, conhecidas como envelhecimento, podem ocorrer durante a operação, influenciado na resistência à fluência. Desta forma, a caracterização dos estados de envelhecimento de uma liga HP torna-se necessária para avaliar a sua vida remanescente. O objetivo deste estudo é caracterizar duas condições microestruturais de uma liga HP com a microscopia eletrônica de varredura e o ensaio não destrutivo de ultrassom. O processamento do sinal ultrassônico, utilizando a Transformada Rápida de Fourier (Fast Fourier Transform – FFT), foi realizado sobre o segundo eco de fundo do sinal ultrassônico, permitindo correlacionar a análise espectral do sinal com a microestrutura do aço HP. De acordo com a metodologia proposta, os dois estados de envelhecimento foram caracterizados através do processamento do sinal ultrassônico.

Oct 30, 2017

By J. C. Barker

Alaska, with about 74% of the US continental shelf, is largely unexplored for placers in its vast shallow marine waters. Nevertheless, there are numerous occurrences of marine minerals including gold, platinum, and cassiterite. Offshore dredging has recently begun in the Nome area. State and Federal agencies are preparing additional acreage for leasing. With 76,200 km (47,300 miles) or 54% of the US coastline, Alaska is a vast, largely unexplored frontier for shallow-water marine placers. Despite the general lack of mapping and only sporadic past prospecting, many prospects are known and a major mining operation for gold has recently begun offshore of Nome. Due largely to the demonstrated success of the Nome operation, the US Minerals Management Service is preparing to conduct a lease sale of additional acreage further offshore from Nome. And future sales are being considered elsewhere by both the Federal and state leasing agencies.

Jan 1, 1990

By H. E. Powell

The magnetic susceptibilities of 34 manganese-bearing minerals were determined. The source of each sample and petrographic, spectrographic, and chemical analyses are given. Included are values for ismorphous series showing wide ranges of composition and for a few high-purity synthetic minerals.

Jan 1, 1968

By Anna Paula Littig Berger

O objetivo do presente trabalho foi estudar a influência da adição de argônio à atmosfera de redução a plasma sobre a redução de pós de hematita. Os experimentos de redução foram realizados em reator a plasma pulsado DC, sob pressão de 533 Pa, temperatura de 380ºC, tempo de 60 min, fluxo total de hidrogênio e de argônio de 400 cm3/min e variando os teores de argônio e hidrogênio. Os resultados mostram que os aglomerados de partículas após redução possuem um aspecto esponjoso. Verificou-se que o uso de uma mistura gasosa contendo 2% de Ar e 98% de H2 permite um aumento de aproximadamente 7,76% na fração de redução.

Aug 8, 2018

Throughout the 1970s, the US Bureau of Mines rode an ebb tide in Washington political circles. In rapid fire succession, the agency lost its mine health and safety enforcement responsibility (1973), a large portion of its energy research responsibility (1975), and then its fuel statistics functions plus a sizable portion of its coal R&D (1977). By 1978, johnny-come-latelies in the Energy, Labor, and Interior Departments had siphoned away from the Bureau some $125 million in program responsibilities as well as 900 of its employees. The bruising decade came to a close with a Department of Natural Resources proposal that, in its original form, would have scattered the Bureau's responsibilities to the winds. "There is no doubt in my wind," said Lindsay Norman, acting director of the Bureau of Mines (see box), "that were the Bureau to continue down the path it was on, the next step was closing the doors and going out of business." The doors are still open, but erosion of responsibilities had a devastating effect on the resources available to fulfill the Bureau's mission. Devastating, too, in terms of internal morale, considering the Bureau had six directors in a 10-year span. "When the troops are in the trenches and are being shot at," Norman said, "they need a leader-hopefully, a permanent one- that can get them advancing. This is something the Bureau did not consistently have in the 1970s." In September 1978, Roger Markle climbed aboard as director of the Bureau to rejuvenate the 70-year-old agency. He resigned only six months later* but the program Markle set in motion is being carried through by Lindsay Norman. Since Norman's appointment as acting director, he has spent considerable time on the road explaining his agency's redefined goals. At one such stop in Duluth, Norman and his two deputy directors, Charles Kenahan and Mike Kaas, answered the following questions. Lindsay, you were the principal architect in the Bureau's 1979 reorganization. How about a glimpse of what that entailed? Toward the end of the 1970s, after almost a decade of steady dismemberment, we reached what we felt was a critical point in the Bureau's history-we had the choice of redefining and strengthening our organization to meet the mineral challenges ahead, or continuing down the path toward the agency's eventual demise. We felt the Bureau's mission too important to abandon, so in 1978 with Roger Markle as director we initiated a six-month, no-holds-barred intro spection of just what the Bureau should be doing, why, and toward what ultimate national needs. And what did this self-reflection reveal? That there is, indeed, a unique federal role for the Bureau of Mines-that of a lead agency for influencing mineral decisions and pioneering tomorrow's technologic advances. Don't confuse us with policymakers, we're not. But we are policy analysts; we're scientists, engineers, and mineral professionals who can offer a sorely needed source of objective, accurate information to decision makers in both the public and private sectors. I feel there is no better brain trust in government than the Bureau when it comes to mineral expertise-of course, I'm biased. Do I understand you to say the Bureau of Mines is an advocate agency for the minerals industry? We plead no parochial interests, nor ought we, but from our viewpoint a sound minerals industry is extremely important to the broader national goals of security and a healthy economy. US dependence on foreign sources for critical minerals, the increasing noncompetitiveness of some US mineral sectors, and the array of land use issues surrounding mineral-rich lands all have much more serious implications than many otherwise informed people seem to recognize. In your estimation, how vulnerable is the US to foreign mineral suppliers? Let me make a distinction between dependency and vulnerability. The

Jan 4, 1980

By H. Marshall Farrier

In the past few years the world petroleum industry has increasingly felt the weight of changes in the principal economic factors affecting pro¬fits. As a result of, these changes, it has been necessary for many oil companies to acquire certain new facilities in order to strengthen their competitive positions and thereby protect their tremendous investments in crude oil reserves, pipe line facilities, refining operations, and marketing outlets. Principally these needs have been met by new capital outlays. A supplementary, method of acquiring needed facilities, however, has been to obtain existing facilities through complete or partial acquisition of other companies.' properties. It is this method of meeting competitive pressures with which this paper is concerned. This paper presents a statistical breakdown of the mergers and acquisitions which occurred in the oil industry between January 1, 1954, and October 1, 1959, showing the frequency' with which certain types of properties were acquired in each of the years studied. In addition, it discusses the principal economic conditions which stimulated many of these property trans¬fers, comments on the effects of these mergers on the consuming public, and indicates the types of, mergers and the rate at which they may be expected during the next three or four years. The basic data upon which the statistical analysis presented in this paper is based were taken from several published sources. Obviously they are somewhat incomplete because not all mergers and acquisitions were reported However;, a careful search was conducted through, The Wall Street, Journal, The Oil and Gas Journal, Potroleum Week, and The Oil Daily with the result that the data should be reasonably complete and comparable for each of the years studied, It is believed, therefore, that the statistical analysis which' follows provides a reasonably accurate indication of the general trend in mergers and acquisitions during the period studied.

Jan 1, 1960

By F. K. Shelton, J. C. Stah, Ruth E. Churchward

A study of the hydrometallurgy and electrowinning of cobalt from various domestic ores has been in progress at the Boulder City, Nevada, Experiment Station since February 1940. Previous reports covering certain phases of this investigation have been published. This report covers the research and pilot-plant work on the production of cobalt metal from cobalt-copper ores from the initial experimental work on crude ore through continuous operation. The ore types were from the Blackbird District, Lemhi County, Idaho. The initial tests were made with concentrated ore which was received by air mail and these experiments were expanded both in size and scope. After the laboratory was continued, improved, and extended tests were reported. Sufficiently advanced, a continuously operated plant producing 250 pounds of electrolytic cobalt per day was operated from June 15 through July 15, 1944.

Jan 1, 1948

By Brian D. Barkauskas, Terence P. Holman

A major combined nuclear and coal-fired power plant, located in on the western coast of Florida has undergone multiple upgrades in recent years to increase power output and enhance environmental controls. Construction of new elements within the existing plant structure required working in highly congested conditions and heavy crane lifts with large picking radii. The largest crane pick involved the use of an 1800 metric tonne capacity Mammoet PTC ring crane for a single long-radius, high altitude lift of a precipitator unit. Original bid tender documents had called for drilled shaft foundation support, but the presence of many critical utilities and unfavorable access for cost effective construction led specialty contractor Moretrench American Corporation to propose an alternate micropile foundation on the basis that high capacities could be achieved in the weak limestone geology and that the smaller size of micropiles would allow for more surgical installation in the utility-congested areas. This case history describes the design and construction of seventy three (73) high capacity micropiles for the value engineering alternative and the crane foundation for this critical lift. Each micropile was founded in a competent dolomitic fossiliferous limestone unit at typical depths of 23 m below existing ground surface. Strain gauge instrumented load testing was used to validate the geotechnical design parameters in the weak limestone bedrock and resulted in the finding that the entire test load was being carried in the upper half of the bond zone. Construction of the production micropiles required numerous relocations due to utility conflicts and local reanalysis and redesign of the 1.2 m thick reinforced concrete ring beam cap. Crane foundation performance was satisfactory and the effective life of this temporary foundation was only 6 months before decommissioning and demolition.

Jan 1, 2017

By F. S. Knoll

Magnetic separation employing superconducting technology is now accepted within the Kaolin processing industry, proving the value of this technology and its ability to operate reliably even at the most remote site. Developments in superconducting magnet engineering, including cryogen free operation, combined with experience in mineral processing enables new forms of Wet and Dry superconducting magnetic separation to be developed. Applying the high magnetic force advantages at 5 T else available from such magnets to other materials is now a reality. High magnetic force mineral separating system developments are reviewed allowing the mineral processor to take advantage of a technology that is no longer confined to the laboratory.

Jan 1, 1997

By D. A. Meyn, R. L. Holtz, C. S. Pande, M. A. Imam, D. J. Singh

"Various theoretical and experimental techniques used to search and develop new metal hydride systems suitable for hydrogen storage are described. The main theoretical technique under study makes the use of electronic structure of the candidate materials. Microstructural characterization techniques like transmission electron microscopy are being used to study the hydride formation. Novel processing techniques for material preparation such as those needed to produce thin films or amorphous phases are also being utilized. The techniques are illustrated with results from Pd, FeTi and Mg2Ni systems.IntroductionOf the four methods of hydrogen storage, compressed gas, cryogenic liquid, metal hydrides, and gas-solid adsorption, the metal hydride storage method is more attractive from the point of view of high volumetric density and safety. Compressed gas storage has disadvantages of extreme pressure, weight, and volume requirements, whereas storage of hydrogen as cryogenic liquid is unattractive due to the requirements of extremely low temperatures and high consumption of primary energy. Moreover, the number hydrogen atoms present in a volume of 10- 22 Cm3 (nH) in liquid hydrogen state (- 20K) is 4.2 whereas number of hydrogen atoms that can be accommodated in a free volume of 10-22 cm3 of various hydrides are as follows: LiH--5.9, TiH2--9.2, ZrH2--9.2, VH2--l0.2. High hydrogen concentration is usually associated with a large H/Metal atomic ratio but is also a function of structure."

Jan 1, 1994

By Lanre M. Oshinowo, André Bakker

"An understanding of the parameters that govern the just-suspended impeller speed, Njs, and the distribution of solids, is critical to the efficient operation of hydrometallurgical and other processes involving solid-liquid suspensions. In this paper, the distribution of solids in stirred tanks under a range of solids loadings (0.5 to 50 vol%) was predicted using CFD and validated against experimental data obtained from the literature. The multiphase flow is modeled using the Eulerian Granular Multiphase model. This paper will also review the established design parameter Njs in the context of scale-up and compare it to the quality of solids dispersion as a means of assessing correct scale-up in suspension tank design. The results of this study will describe a straightforward procedure to obtaining comprehensive information about reactor behavior with complex CFD models.The performance of hydrofoil impellers and a 45° pitched-blade turbine at suspending solids under different agitation speeds was studied. Both single and dual impeller operation have been evaluated. The settled solids fraction for speeds below N js, and the cloud height for impeller speeds above Njs were predicted. The CFD predictions are in good agreement with experimental literature data on velocity distribution and cloud height."

Jan 1, 2001

By Robert K. Linn

The New ldria Mining District is in the southern part of the Diablo mountains of the California Coast Range, 140 miles southeast of San Francisco. The district, noted primarily for quicksilver, also has become important recently as a producer of short-fiber chrysotile asbestos. Between 1853 and 1966, the New Idria district produced 568,092 flasks of quicksilver valued at about $55,600,000, 99 per cent of which was recovered from one deposit, the New Idria mine. In 1944, the district was ranked third in all-time production of North American quicksilver districts, and, since that time, the New Idria mine produced an additional 129,045 flasks, placing the district and the New Idria mine second in all-time production. The major structure of the region is the northwest-trending Coalinga anticline consisting of an asymmetric dome of sedimentary beds ranging in age from Jurassic to Quaternary and marked at its northwest end by an oval body of sheared serpentine 14 miles long by 4 miles wide. The serpentine core, rimmed by Franciscan sandstone of probable Jurassic age, was uplifted in stages between Jurassic and Quaternary time and was intruded along a ring of faults into beds of the Panoche Formation of upper Cretaceous age. The core of serpentine and Franciscan rocks is the locus of about 20 quicksilver mines that rim the faultbounded core and lie within the serpentine mass. The host rock of the most productive deposits is altered Panoche shale and sandstone that lies intermittently along the perimeter of the core. Deposits of the New Idria group of mines and those of a few other small mines lie along the northeast contact in the footwall of the New ldria thrust fault, and a few others occur on steep normal faults around the south and southwest. The chief ore mineral in all quicksilver mines is cinnabar, but minor amounts of metacinnabar and native mercury are found in some of the mines. Ore shoots were deposited in fracture zones and stockworks in altered Panoche shale and sandstone and in definite fissure veins in Franciscan sandstone. Rocks made highly amenable to fracturing by hydrothermal alteration were fractured extensively by late faults. The resulting fracture zones, located along the late faults and at changes in strike or dip of the hanging wall or footwall, are the principal controls of most ore shoots. The largest and richest ore shoots are those of the New Idria mine. The major ore bodies occur in fractured shale and sandstone beneath the New ldria thrust fault at its junction with major tear faults.

Jan 1, 1968

By R. E. Heithecker

Zwolle oil field of Sabine Parish, La., is different from most oil producing areas of the State in that the oil is obtained from marl and chalk-rock formations. The thickness of the reservoir rocks averages 500 feet; but production is not continuous throughout this thickness, as the oil apparently is localized in vertical and nearly vertical solution cavities and channelways or in porous zones of limited horizontal extent. The nature of the oil accumulation has caused two outstanding peculiarities of the field: (1) About 60 percent of the tests drilled were dry holes and (2) there were many instances of well interference. Commercial production was discovered in November 1928, after 17 years of prospecting in and around the present limits of the area now developed which has a length of about 22 miles and a maximum width of 4 miles. The field had produced 10,266,896 barrels of oil to January 1, 1934. The oil ranges in gravity from 400 to 420 A.P.I. Although the field is divided into several districts which are more or less clearly defined and separated by unproved territory the term Zwolle field", as used in this report, includes the entire area from Blue Lake on the west side, through Zwolle proper, and eastward, including the Many or Eastern extension.

Jan 1, 1934

By H. Sieber

Multilayer samples of tantalum and aluminum with the composition of Al-25Ta were prepared by cold rolling of elemental foils. The microstructure and phases were characterized by XRD, SEM and TEMISAED and the reactive phase formation was examined by DSC and DTA measurements in multilayer foils rolled for different deformation levels. The rolling procedure yields a decrease of the Ta particle size in the Al matrix and also results in the formation of a multilayer structure with a thickness of the elemental foils down to 200 nm in average. No phase formation is observed during the cold rolling procedure. While XRD and DSC measurements show no phase formation up to the melting of aluminum for samples rolled up to 40 F&R (fold and rolling) passes, in samples rolled for 50 or more F&R passes a first phase formation reaction yield an interfacial layer of TaAl3. Contrary to former studies in the investigated cold rolled Al- 25Ta multilayers the reaction starts at temperatures as low as about 340°C. The first stages of the reaction are associated with two exothermic maxima, that increase in amplitude and shift to lower temperatures with increasing number of F&R passes. At higher temperature the TaA13 reaction layer thickens very sluggishly and yields a third exothermic maxima at about 600°C. Isothermal DSC scans show the reaction is not finished for samples containing elemental particles larger than 1 pm after annealing at 550°C for 5h. In all the investigated samples no Al- Ta phase other than Tad3 was observed to grow for heat treatments up to 800°C. Multilayer samples heated up to 1400°C show a morphology consisting of small AITa2 particles embedded in a single phase TaA13 matrix. The multilayer microstructure and reaction product morphology are characterized by SEM and TEM investigations in cross-section and plan view geometry.

Jan 1, 1998

By Olusegun J. Ilegbusi

"A two-fluid model is used to calculate flow and heat transfer characteristics of a plasma jet. This model accounts for both gradient-diffusion mixing and unmixing that may result from pressure-gradient-body-force imbalance in the system. The unmixedness is considered to be essentially a Rayleigh-Taylor kind instability. Separate transport equations are solved for the plasma and ambient gas velocities, temperatures and volume fractions. The two fluids allowed to exchange mass, momentum and energy through empirical interaction parameters. The empirical coefficients are first established by comparison of predictions with available experimental data for shear flows. The model is then applied to an Argon plasma jet ejecting into stagnant air. The predicted results show the significant build-up of unmixed air within the plasma gas, even relatively far downstream of the plasma torch. By adjusting the inlet condition, the model adequately reproduces the available experimental data on the temperature profile.IntroductionPlasma jets have important applications in materials processing, some of which include spray deposition, melting and refining, heat treatment and materials synthesis. In a typical reactor, the hot plasma stream entrains a surrounding gas and the resulting heat and mass transfer and the condition of operation of the torch, determines to a large extent, the performance of the unit. The entrainment may prevent uniform mixing and produce regions of unmixed hot/cold gases and non-uniform deposits as a result of insufficient melting of deposit in cold regions. This phenomenon may also affect chemical reaction rate in plasma systems for NOx reduction in exhaust gases.The study of plasma phenomena is often conveniently divided into three parts namely, the plasma torch, the plasma jet and analysis of the particles carried in the jet. The present work concerns processes occuring in the near-field of the plasma jet i.e. just downstream of the torch."

Jan 1, 1994

Separation performance of a Floatex Density Separator (FDS) has been studied both experimentally and theoretically. Experimental results reveal that at a lower bed pressure the FDS acts like a classifier. Higher bed pressure is required to attain the concentration effect as proper development of suspension density occurs under these conditions. It is seen that the size or density alone is not able to describe the partition fully. The terminal settling velocity, which includes both the size as well as the density of the particle can be a useful descriptor of separation in a FDS. While a narrowly distributed feed offers better performance of a FDS, a wide size distribution of feed results in large scatter in the terminal settling velocity distribution and renders the separation difficult. The closely sized feed enhances the density effect in concentration. A higher teeter water flow rate also helps in carrying larger-lighter particles to the overflow by increasing the cut off terminal settling velocity as it increases the net upward force. A detailed description of separation performance in a Floatex Density Separator has also been established from theoretical considerations. Separation performance of the separator is described using a simple slip velocity model. The model has been validated com-paring the predicted FDS performance results with those experimentally measured under widely different operating conditions.

Jan 1, 2014