Search Documents

By D Craw, K A. Hunter

Deposits of the metalloids arsenic and antimony occur in quartz veins of mesothermal hydrothermalsystems in the South Island as arsenopyrite (AsFeS) and stibnite (Sb2S3). Arsenopyrite and stibnite occur in natural exposures in gold-mining areas, and additional arsenopyrite and stibnite have been exposed to the atmosphere by mining activity. At present the drinking water limits for dissolved As and Sb are 10 ppb and 3 ppb respectively. Sampling and analysis techniques are critical to determination of metalloid concentrations at these low levels. Endeavour Inlet in the Marlborough Sounds is an historic mining area (late 19th Century) with elevated As and Sb in waters emanating from mineralised rocks. Waters running out of abandoned adits have concentrations of As and/or Sb up to ppm levels. Natural waters have high Sb and low As, and the As levels increase markedly where anthropogenic activity has exposed rock. Changes in Sb/As ratio could potentially be used to quantify the anthropogenic component of metalloid mobility on mine sites on the 100-year time scale.

Jan 1, 2002

By J. L. Johnson

The U.S. Department of the Interior, Bureau of Mines, investigated recovery of concentrates containing tin, tantalum, and niobium from the Kougarok deposit on the Seward Peninsula, AK. To date, 25 million lb of tin has been delineated in occurrences containing 0.36 to 1.32 pct Sn, and the resource potential is estimated to be as high as 25 million short tons at average grades of 0.75 pct Sn, 0.025 pct Ta, and 0,025 pct Nb. Deslimed ore was concentrated to 54 pct Sn, 0.3 pct Ta, and 0.3 pct Nb, with recoveries of 74 pct Sn and 44 pct Ta/Nb using a Humphrey's* spiral followed by a Deister shaking table. Tin values in the slimes were upgraded to a 5-pct-Sn concentrate using a Bartles-Mozley separator followed by flotation. The 5- pct-Sn was further upgraded by fuming to give a concentrate containing approximately 60 pct Sn. The recovery of the two products combined was 80 pct Sn and 46 pct Ta/Nb, A flowsheet with mill-design parameters resulted from the metallurgical testing. An economic analysis was made based on the proposed process.

Jan 1, 1990

By Jessica Egan, Daniel Hodouin, Claude Bazin

"The recovery of gold by leaching is influenced by the size of the gold carrier particles and the chemical environment. Using the relationships between the leaching rate, infinite recovery and particle size for a given set of chemical conditions, it is possible to simulate gold recovery for various feed size distributions. However the use of these particle size relationships is only valid if the leaching of gold from a given size class is independent of the production history of this size class. For instance, to use these relationships it is necessary to verify that gold recovery from the leaching of the 200-270 mesh size class remains the same if the size fraction is taken from a coarse or finely ground ore sample. Several laboratory tests were carried out to answer that question. Results of the tests show that within the large error margin associated to gold content measurements, the history of the production of a size class does not affect the gold leaching from that size class. Emphasis of the discussion is put on the difficulty associated with the processing of data containing significant measurement errors as it is the case for gold assays of leaching tests.INTRODUCTIONMore than 75% of the gold produced in the world is extracted by cyanide leaching of gold ores. The ore is ground to expose the gold carriers and the ground material is reacted in an oxygenated cyanide solution that dissolves gold, leaving solids gangue minerals that are disposed to tailings ponds or returned in underground mines as paste fill. The gold contained in the solution is recovered by either the carbon in pulp process or by cementation onto zinc powder, before being melted and casted into a brick (Marsden and House, 2006)."

Jan 1, 2009

By Lloyd A. Morley

The problems associated with the presence of organic materials and of water in explosion-proof enclosures used in high voltage, high capacity applications were examined through a literature search and theoretical reasoning. Information on volatilities is presented. The conclusion is reached that explosive pressures are significantly enhanced by inclusion of these materials.

Jan 1, 1976

Arsenic (As) removal behavior from Changgoon mine tailings was investigated using Acidithiobacillus ferrooxidans (A. ferrooxidans) in well-controlled batch reactors by varying pulp density (0.5?4%, pH=1.8, temp=30oC), reaction initial pH (1.8?2.2, pulp density=0.5%, temp=30oC), and temperature (25?35oC, pulp density=0.5%, pH=1.8). The initial concentration of As in the mine tailings used for bioleaching tests was about 30000 ppm, and the size range of tailings used in this study was 63?74 µm. The reaction speed and initial cell concentration were fixed to 150 rpm and 107 cells/mL, respectively. To complement leaching experiments, pH, oxidation/reduction potential (ORP), and amount of ferrous/ferric ions in leachate were analyzed. Scanning electron microscopy and x-ray diffraction analyses were also conducted for the samples before and after leaching to see if any morphological and compositional changes in tailings took place during leaching process. The As leaching efficiency increased with decreasing pulp density, decreasing pH, and increasing temperature in the presence of A. ferrooxidans. Specifically, no significant change in As removal rate was observed when pulp density d 2% while the removal rate dramatically decreased at pulp density of 4%. Regarding pH effect, As removal rate was much more enhanced at lower pHs (i.e., 1.8 and 2.0) compared to pH 2.2. Increasing temperature was observed to tend to enhance As removal rate, showing about 20% enhanced leaching rate under 35oC compared to 25oC and 30oC at the elapsed time of 5 days. The results for As removal behavior at different conditions (i.e., pH, temperature, pulp density) were consistent with the change in pH, ORP, and ferric ion concentration in leachate, showing greater removal rate at the condition with lower pH, and higher ORP and ferric ion concentration in leachate. Furthermore, decreasing removal efficiency was likely in part due to the extent of the formation of by-product (i.e., jarosite) of ferric ions.

Feb 27, 2013

The Subtropolis mine is a room-and-pillar mine extracting the Vanport Limestone near Petersburg, Ohio. In February 2018, mine management began implementing a heading reorientation to better control the negative effects of excessive levels of horizontal stress. The conditions in the headings improved, but as expected, stressrelated damage concentrated within crosscuts. The mine operator has worked to lessen the impact of the instabilities in the outby crosscuts by implementing several engineering controls. With the implementation of each control, conditions were monitored and analyzed using observational and measurement techniques including three-dimensional (3-D) LiDAR surveys.

Jan 7, 2020

By G. G. Barbante

The oxidation behaviour of selenide matte with a substantial Cu content and low Ag differs significantly from that of high-Ag matte. Low-Ag selenide mattes display a large oxygen solubility and the upper boundary of the miscibility gap in the Ag-Cu-Se-O system is depressed to quite low Se contents. As a result, the formation of Ag metal is considerably delayed. The oxidised selenide matte, low in Se and with a relatively high oxygen content, has previously been termed oxymelt. With further oxidation, its composition enters the misciblity gap and crude Ag is formed. The sodium silicate slag captures very little of the SeO2 and the dissolved Ag2O(s) content of the slag is relatively small, with a Raoultian activity coefficient of 0.57. This value was found to be independent of the slag's Cu2O content

Jun 19, 1905

By P. R. Brenchley

Main ore pass systems should last the life of a mine, and too often expensive and hazardous remedial measures are required to repair a damaged ore pass in an attempt to extend its life. In order to maximize the life expectancy of all ore passes at Moab Khotsong, ?wearing blocks? and ?softer support? systems, combined with basic rock engineering principles, have been implemented. Failure of an ore pass can have severe financial implications, both indirectly because the ore pass cannot deliver the broken rock either from level to level or directly in the shaft ore pass system to the required level for tramming to take place, and directly due to the cost of the repair work that is required. Several factors need to betaken into consideration so that production interruptions are eliminated or minimized. Investigations of damaged ore passes at Moab Khotsong and surrounding mines revealed some interesting mechanisms of damage, and some innovative methods of reducing or eliminating the damage have been implemented at Moab Khotsong. The system design was based on 30 years, experience in main shaft rock passes. The design was to counteract scaling, hang-ups and dust problems associated with main rock passes, and the objective was to increase the life of rockpasses. These problems, including the initial design aspects to try and eliminate the repair measures, are discussed in detail.

Jan 1, 2006

By Elaine T. Cullen

Miners, like many skilled blue-collar workers, are not traditional learners. They have not always been successful in classroom-type settings, preferring to learn on the job in a hands-on environment. U.S. law requires that miners have a minimum of 8 hours of safety training annually, plus 40 hours for underground miners and 24 hours for surface miners when they enter the industry. However, miners rarely view this training time positively. In fact, it has been called “safety jail” by many, who regard it as a time to get a little extra sleep While mining has become far safer in the past 100 years, it is still a dangerous occupation. The Office for Mine Safety and Health Research, a part of the National Institute for Occupational Safety and Health (NIOSH), has funded a project for the past 4 years to address this challenge. The purpose of the research was to find a way to develop effective safety training for these people. Miners are born story tellers. They share “near miss” stories, stories about master miners they have known, and stories about how things used to be. These stories not only pass along information about what will happen if a miner fails to respect the mining environment, they also instruct listeners in the culture of mining and the values that it embraces. Stories, it seems, are a way to get safety messages across to miners, especially inexperienced ones, and using older, wiser miners in these stories is an obvious choice. This paper will discuss how a series of training videos was developed, how “master miners” and story lines were chosen, and how the resulting videos have been received in the mining industry.

The Main Seam occurs in two 'pods', termed North and South, separated by an east-west oriented 'want' zone (most probably a palaeo-channel). The seam on either side of the 'want' area reaches thicknesses of over 30 metres but the North Main Seam adjacent to the 'want' zone has been split into multiple seams of 10 to 15 m thickness. Rock types in the inter-burden of this area are characterised by inter-bedded sandstones and carbonaceous mudstones varying in thickness from 0.5 to 5 m. In the South Main Seam, an area of un-split coal exists and is characterised by few inorganic partings. Overburden in this area varies geographically from relatively thick mudstones in the south and east part of the coal deposit to inter-bedded sandstones and carbonaceous mudstones adjacent to the 'want' area. The sandstone/mudstone overburden probably represents a splay or splay-channel complex emanating from the larger 'want' area palaeo-channel. Modelling lithological variability is of use because it is one of the factors used in predicting cavability and roof support system design. The coal in both the north and south deposits were found to exhibit highly predictable quality and breakage parameters in relation to the coal geometry. Although ash yield and sulphur are mostly low and not variable, volatile matter and thus fixed carbon, varied in relation to seam thickness. In general, volatile matter (dat) decreased and moisture increased with decreasing seam thickness whereas moisture increased with decreasing seam thickness. In addition to these parameters it was found that the energy needed to crush the coal was lowest at the top and bottom of the seam and, on a whole seam basis, decreased with seam thickness. All of these parameters were found to vary in relation to the vitrain band content of the coal which itself was controlled by seam geometry. These parameters can therefore be modelled and inputted into mining plans and quality control operations.

Jan 1, 1996

By L. J. Tucker

The magnetite orebody at Pea Ridge strikes NE-SH and dips at about 800 to the SE. The ore is high grade magnetite with a strike length of over 600-m and a maximum width of over 180-m on some of the levels. The shape and the mineral content of the iron orebody have been fairly consistent so far. The iron ore and surrounding basement rocks are Precambrian in age. These rocks are usually very competent, about 400-m of sediments lie over the ore.

Jan 1, 1991

By M. A. Hermanus

This paper examines the occupational health and safety performance (OHS) of the South African mining sector against the backdrop of changes in the composition of the sector, international trends in OHS performance, and the agreement on OHS milestones and targets by mining stakeholders at the Mine Health and Safety Summit of 2003. Although OHS performance has improved, progress is slow and there is need for significant rather than incremental change if the targets are to be realized. Since 2003, fatalities and injuries are 20?25% short of annual milestones and not all commodities show consistent improvement. Statistics on occupational health impacts are unavailable, but noise and respirable dust levels are known to be high in mines, with much work lying ahead to address exposures at source. Trends in regulating and addressing OHS hazards are discussed with reference to the notion of ?systems-thinking? and the targets. Efforts to improve OHS and to respond to changes in the sector are constrained by a lack of training and consistency in risk management, guidance for junior, small and artisanal miners, and holistic approaches to risk. For example, treating risk holistically would involve taking proper account of contractors and women in the workplace, and attending to human factors and ergonomics.

Jan 1, 2007

By Paul Worsey, Seokbin Lim

There are two major types of shaped charges, conical and linear (Ref 1, 2). Conical shaped charges are used to perforate targets and are mainly used by the military as anti armor weapons and by the oil industry for oil well perforation. In contrast, linear shaped charges are primarily used to cut metal in the demolition industry with other uses including separating devices in the space industry. There is a large amount of material published on conical shaped charges because of the high level of defense industry research and funding, however in stark contrast there is very little published on linear shaped charges.

Jan 1, 2003

By Colin C. Harris, Jie Zheng

While applications of stirred media mills for fine particle production have continued to increase, there is a lack of understanding of operating behavior and power requirement. Investigations in laboratory stirred media mills have been carried out with grinding media, limestone and yttria stabilized zirconia. The torque required to rotate impellers immersed in dense particulate media with supernatant versus impeller rotational speed displays four regions marked by sharp transitions: transition from static to dynamic friction; channel- ling; dispersing; and centrifuging. Equations, including dimension- less group correlations of power and modified Reynolds number, for relating power, speed, impeller and tank dimensions and design, media size and density, solid concentration, and other relevant variables have been established. Scale-up guidelines with respect to power consumption are also proposed. The best operating conditions for grinding limestone in the laboratory stirred media mill have been identified. Complexation by the polymer during ultrafine grinding of zirconia has been found to cause extraction of yttrium into solution with possibly significant changes in the surface chemical composition of the product.

Jan 1, 1995

By J. R. Guard

Development of electrical power in coal mining has been an outstanding example of adaptbility. It has accommodated itself to new inventions, changing mining methods, increasing demands, increasing safety requirements and many other new conditions. With the appearance of the continuous miner in the mining machinery picture, those engineers interested in the application of electricity to mining have been thinking about what new comination of electrical apparatus will best suit this newcomer. It is the purpose of this paper to discuss the relative costs of supplying d-c versus a-c power to mining equipment with particular reference to continuous miner setups. Assume that a-c power will be delivered to the mine at some high voltage suitable for transmision to the various substation locations. Typical voltage for this purpose is 4000 volts. The problem then is to change the power to some kind of power suitable for driving the motors of mining equipment. For safety and other reasons the voltage to be delivered to the motor terminals must be under 600 volts.

Jan 6, 1950

By Franz Albert Nonnen

Backfill systems have been used for as long as mining activities have existed. Various backfill methods have been developed over the centuries with consideration for geological necessities, the technical means available, security requirements, and available finances. In the past, backfill systems were introduced and upgraded geographically in accordance with local experiences. In modern times, mining engineers participate in international forums for the exchange of knowledge so that backfill techniques and experiences are shared concurrently in mining areas all over the world. Mine backfilling increases the cost of mining so that great attention must be paid to choose a low-cost, reliable, and low maintenance backfill system. Some methods are described in this paper.

Jan 1, 2001

By Steven J. Schatzel, Robert B. Krog

Frictional ignitions are defined as the ignition of a flammable mixture of methane and air that is initiated by frictional heating. Ignitions created through the addition of energy from open flames and exposed electrical circuits are not included in this analysis. Energy released in a roof fall that creates a spark and ignites a methane mixture would be considered a frictional ignition. Frictional ignitions represent the majority of all ignitions in underground coal mines. Over the study period of 1983 to 2005, a total of 1993 ignitions were reported in underground bituminous coal mines in the United States, of which 1589 were frictional ignitions. Reportable ignitions to the Mine Safety and Health Administration (MSHA) are any unintentional occurrences of flame underground regardless of duration. Frictional ignitions were reported in 155 mines and 13 states. Continuous miners represented the largest source for frictional ignitions with 1090 (68.6% of all frictional ignitions). Longwall mining operations represented the highest concentration of frictional ignitions during this study period with 1365 frictional ignitions (85.9% of all frictional ignitions). The 17 mines with the most frictional ignitions were all longwall mining operations and had 1130 frictional ignitions (307 from the shearer) that represented 71.1% of the total. In 1983, mines with frictional ignitions represented 6.9% of operating underground mines and 36.6% of total underground coal production. The percentage of operating underground mines with frictional ignitions and their total production has increased steadily and in 2005 represented 9.8% of active mines and 46.2% of underground coal production. The three coalbeds with the highest number of frictional ignitions (Blue Creek, Pittsburgh No 8, and Pocahontas No 3) had 1049 ignitions that represented 66.0% of all frictional ignitions. The three states with the highest number of frictional ignitions were Alabama (710), Virginia (247), and Pennsylvania (242) that represented 75.5% of the total. Frictional ignitions peaked in 1991 with a high of 114. In 2005, only 34 frictional ignitions were reported. If only frictional ignitions that occur at the face are considered, there have been no fatalities since 1983. Since this time, there were 33 ignitions that caused 53 workers to lose a total of 2912 working days. When including ground falls, then there have been four frictional ignitions with one incident causing two fatalities and injuring eight workers. From 1983-1991, underground productivity and the number of frictional ignitions increased. However, productivity continued to increase from 1991-2000 while total frictional ignitions fell, thereby disproving this connection between productivity and frequency of frictional ignitions. Ninety percent of all frictional ignitions occurred in underground coal mines that liberated more than 393 L/s (1.2 MMcfd million cubic feet per day) of methane through the main ventilation system. Although methane production is not the determining factor for the occurrence of frictional ignitions, it is a good indicator of the anticipated frequency.

By R. C. Wang

Solid-liquid flow in different pipe geometries was investigated. This investigation was conducted by measuring delivered solids concentration and head loss. The delivered solids concentration was measured to study the effect of pipe geometry on the minimum carrying velocity above which solids do not lag behind the fluid. Head loss was measured to study the effect of pipe geometry on the friction loss. A mathematical formula was developed for determination of the minimum carrying velocity. Darcy-Weisbach's equation and Durand's equation were used for comparison of head losses of pipe shapes. Of the different pipe shapes studied, each having the same interior cross-sectional area, the rectangular pipe with the wide side oriented as the base yielded the lowest minimum carrying velocity at high solids concentrations. The minimum head loss at low velocity and high solids concentration also was attained with this pipe. Although the circular section is known to be the best for transporting liquid only, the present study suggested that pipe geometry is a factor in lowering the operating velocity and reducing head loss in solid-liquid flow.

Jan 1, 1973

By Mike Trovant, Stavros A. Argyropoulos

"A fixed grid numerical model for phase change problems is proposed. The model solves for heat transfer and fluid flow, via the coupled solution of the energy, continuity and momentum equations. In addition, the numerical scheme accounts for temperature varying thermophysical properties and determines the shrinkage profile resulting from phase and density change. Simulations are run to determine the effect of varying model parameters and wall cooling rates on the location and shape of the shrinkage void formation in cylindrical casts. Results are shown for both aluminum and magnesium.IntroductionThe mathematical modeling of phase change processes (be they solidification or melting problems) entails solving for many interrelated phenomena. A comprehensive numerical simulation of the casting of a metal, for example, would have to account for: (a) heat transfer in both the solid and liquid portions of the metal and in the mold, (b) the release of latent heat during phase change, (c) fluid flow behavior in the liquid portion of the metal, (d) temperature induced shrinkage caused by liquid contraction and solidification contraction, and (e) the development of thermal stresses with accompanying shrinkage in the solid portion of the cast and mold. A schematic of the relationships that exist between the coupled equations which govern solidification is shown in Figure 1."

Jan 1, 1994

By D. Brady

There are many examples, historical and recent, from the underground coal mining industry where during emergency response the response and ultimately the outcomes, could have been significantly improved if adequate systems had been in place for the collection and management of relevant information preceding the incident, the acquisition of information during the incident and the use of the information for risk mitigation and decision making purposes. The subject and process of knowledge management is possibly the most critical for would be rescuers of endangered coal mine workers, as it has been demonstrated at numerous coal mine incidents that a lack of or mismanagement of crucial information can be fatal for both the rescuer and/or the endangered coal mine worker. This paper will underline the scope and importance of robust knowledge management systems for emergency response within the underground coal mining industry and the process by which it is being achieved within the Queensland Mines Rescue Service and the NSW Mines Rescue Service.

Jan 1, 2012