Search Documents

By K. H. McDaniel, L. Griswold

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to supplement its two existing main fans. The third fan will operate in parallel with the two existing fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, NM, is a US Department of Energy (DOE), Carlsbad Area Office, facility that is designed to permanently dispose of US defense-generated transuranic waste in a deep, bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for modifying, supplementing or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel et al., 1997) to identify and quantify operational concerns, evaluate possible alternatives and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness and improving system performance. The fan installation project accommodates several operational and scheduling con¬straints. WIPP was scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP 's ability to declare facility readiness. Therefore, operational disruptions during the system tie-in had to be minimized. All engineering for the project has been com¬pleted, and physical modifications were begun in July 1997. The project was completed in 1998.

Jan 1, 2000

By R. R. Unterberger

Three different physical techniques have been used to see through or probe into rocks, so miners might know what is ahead or overhead. These are radar, sonar, and a unique type of sonar called nonlinear sonar. Five radar systems have been developed. The highest frequency used is 4300 MHz for detecting small fractures at close range. This gives the best resolution. For longest range (over 2000 m, or 6560 ft) we use the 30 MHz radar for finding faults ahead of mining or ranging to salt dome flanks. Two types of salt, dome and bedded, are recognized. Radar works well in dry (dome) salt, but not in bedded salt which contains small amounts of water. The dipole moment of water absorbs energy from the radar. Thus was born the 30 MHz radar system and sonar probing systems. These can probe to 100 m (328 ft) even into wet salt. All probing systems measure data in time, which are converted to distance by measuring the time of travel of radar or sonar through salt pillars of known thickness. Ranges of probing in salt are from less than 1 m (3.3 ft) to more than 2000 m (6560 ft). Uses of radar and sonar probing in mines include mapping the top of salt above a mine; mapping salt dome flanks; finding impurities in salt such as anhydrite, sandstone, or potash stringers; locating old boreholes in salt pillars; locating fractures in salt; and finding faults or water zones ahead of mining.

Jan 1, 1985

By G. Sedelnikova

This paper is aimed to elucidate the problem of copper losses in pyrometallurgical slag. Currently, flotation is used to recover copper from the slag and return the metal into the pyrometallurgical process, but the percentage of recovery frequently remains unacceptable. The process of copper leaching from the slag flotation tailings using biologically regenerated ferric sulfate is considered here as an approach to the issue. A sample of the slag flotation tailings containing 0.67% Cu and 4.99% Zn was supplied by the Urals Mining and Metallurgical Company (UGMK, Russia). The Cu and Zn speciation analysis of the sample demonstrated that Cu occurred as 58.1% oxide, 15.4% native Cu, and 18.1% secondary sulfides whereas chalcopyrite proportion was as low as 8.4%. Prevailing Zn species were refractory (58.9% Zn ferrite), and zinc oxide and silicate species made just 37.2% of the total metal content. The silicate generated silica gel that strongly hampered filtration. As demonstrated, Cu recovery is a possibility, which is apparently not the case with Zn. In this work, the stirred tank bioreactor acid leaching employing bacterial Fe3+ sulfate solutions was studied, with ferric sulfate being a product of Fe2+ biological oxidation and not the chemical reactant adding of Fe3+ sulfate. Acidithiobacillus, Sulfobacillus, and Leptospirillum bacilli were employed in Fe2+ biooxidation. Temperature, pH, Eh, S:L ratio, leaching time, and Fe3+ concentration in the source leachate as the process controls were considered. As demonstrated, the process employing biologically regenerated ferric sulfate proved to be more efficient than conventional chemical leaching. Under the optimum conditions, the proportion of Cu extracted into leachate during 2 hours was 79.1%, and that of Zn 27.2%. Precipitation of high-grade Cu sulfide served to extract the metals from the leachate, and Cu extraction was 99.7%. All in all, 23.2% Cu, 0.03% Zn, and 0.02% Fe was returned into the pyrometallurgical process. Keywords: slag flotation tailings, copper leaching

Sep 1, 2012

By John Sasadi, Karl Heinz Zepter, Leonard Sugin, Roger L. Hulette

Mt. Newman Mining Co. is now completing an expansion program, begun even before initial construction was complete, which will result in the ability to ship up to 35 million tpy of iron ore by early 1973. Located in the Pilbara region of Western Australia, the mine at Mt. Whaleback is about 700 road miles north of Perth and 265 railroad miles south of the port facilities at Port Hedland. Development of the tertiary crushing and screening facilities best illustrates the orderly, but rapid, sequence through which the capacity of the port loading terminal has been expanded. When the present program is completed, crushing and shiploading capability will reach - - 35 million tpy. Operations commenced in 1969 with 3 crusher lines in service; and despite the 5-million annual ton rating, 6.46 million tons of ore were shipped during the first full year of operation. With continuing increase in ore sales, expansion to an annual capacity of 12 million tons was authorized, and installation of two more crusher lines was begun. As a part of this program, provision for installation of a sixth crusher at some future date was included in the planning; but before construction was completed, new ore sales contracts demanded further expansion to an annual rate of 20 million tons, and the sixth crusher line was authorized. The distributing and collecting conveyors had been designed for extension in length and increase in capacity, therefore, conveyor service was provided for the additional crushers with additional belting and hardware only.

Jan 6, 1972

By E Yll÷, O HyvSrinen

Outokumpu has developed a new chloride leach process, called HydroCopper«, to treat copper concentrates. Chalcopyrite is quite refractory in leaching and in sulfate milieu an autoclave of high temperature and pressure is required. However, in the HydroCopper«-process copper sulfides can effectively be leached in atmospheric pressure using strong, aggressive chloride solution and copper (II) ions as oxidant. Copper is precipitated from the purified pregnant leach solution as copper (I) oxide, which is filtered and reduced by hydrogen gas to metallic copper powder, which is melted and cast into copper product. Sodium chloride formed in precipitation is decomposed in a chlor-alkali electrolyser, the products of which are circulated back to the process: sodium hydroxide to copper (I) oxide precipitation, chlorine gas to leaching and hydrogen gas to the reduction of copper (I) oxide. During 2003 - 2004 the performance of the HydroCopper«-process was confirmed in a demonstration plant processing one tonne of copper per day. It has been found to be applicable for different kinds of concentrates and can also tolerate a wide range of impurities. A significant advantage of the process is that gold can be leached as a chloro-complex and recovered with active carbon. HydroCopper« can economically recover copper from concentrates and process to a cast copper product. The best utilisation of the process is in most cases achieved when the plant is situated at the mine site. Higher recoveries are attained by the optimisation of the whole operation chain from the mine and the concentrator to the HydroCopper« plant.

Jan 1, 2005

To develop a business case that promotes adoption of noise controls by reducing barriers to industry acceptance and enhancing drivers that foster their implementation. Background Over 75% of the U.S. mining workforce is exposed to hazardous noise, putting them at risk of noise-induced hearing loss (NIHL). Consequently, coal miners suffer high rates of hearing impairment that increase to 70%-90% by retirement age. To address the noise problem for coal miners, researchers from the National Institute for Occupational Safety and Health (NIOSH) first determined that the continuous mining machine (CMM) ranked first among machines associated with reported coal noise overexposures. Further studies found that most CMM noise is generated by three component systems on the machine: dust collection, cutting, and conveying. Of these systems, the on-board chain conveyor was found to be a dominant noise source. Noise generated by the conveying system was addressed through the development of a urethane-coated flight bar chain. The coated chain, shown in Figure 1, has demonstrated an 8-hour time-weighted average (TWA) reduction of operator exposure by 3 dB(A). It has since been accepted by the Mine Safety and Health Administration (MSHA) as a "technologically achievable" noise control for CMM operators who are exposed to noise that exceeds the MSHA permissible exposure level. Having demonstrated the noise reduction performance of the coated chain, NIOSH has assembled information into a business case that can be used by operations considering adopting the chain at their worksite.

Dec 1, 2009

By R. B. Humphrey

Cut-and-fill mining methods at the Thompson Mine have undergone significant changes since production began in 1961. Changes have been introduced in almost all aspects of the mining operation, from the original timbered chutes and air-operated slushers to the present-day bored raises, footwall ore passes and load-haul-dump units. This paper describes the evolution of mechanized cut-and fill mining methods, highlighting the changes in design for stopes and service openings, ground support methods; hydraulic filling and ventilation systems. A mechanized stoping area is described from the initial mining concept through design, development, construction and mining cycles.

Jan 1, 1979

By Dan Witkowsky

In an increasingly environmentally conscious world, mining's importance to society has often been misunderstood and even maligned by the public. Extreme and impractical ideas have often been presented to children because of the lack of accurate, timely resource materials available to educators. In the late 1960s. two mining engineers, S.P. "Pi" Warren and C.L. "Lindy" Barker, became aware of this situation. They proposed to develop a summer field course to provide a factual overview of the minerals industry for teachers. The pair believed that teachers could become better informed to educate students, and future generations, about mining. These two Colorado Mining Association (CMA) members felt that such a course could reduce much of the misunderstanding about this vital industry. This could be done by providing a balanced perspective of mining, not only for kindergarten-through-grade-12 teachers, but also for the students they would be teaching during their careers. Students who better understood the minerals industry could better formulate an unbiased view of it. The course would seek recognized authorities from industry, academia and government who would lecture in their respective fields of expertise. The course would provide a total concept of the coal, aggregate, metals and industrial minerals industries. It would include geology, geophysics, exploration, mining, processing, marketing, product applications, economic, mining history, careers, and environmental responsiblity. When possible, site visits would permit educators to view operations and to meet the men and women who are industry leaders. Teachers would pay a small tuition fee. The balance of the program expenses for each teacher would be paid through scholarships provided by industry and individuals. The "total concept" idea obtained the support of the minerals industry. The support of CMA's Education Committee and the Colorado School of Mines (CSM) was obtained in 1968. Colorado's Commission on Higher Education approved teacher recertification credits through CSM's Office of Special Progams and Continuing Education for those successfully completing the program. The first six-week series of classes presenting the total concept of the indus¬try was held at CSM in 1969. In 1977, the CMA Education Foundation Inc. (CMAEF) was established as a Colorado nonprofit corporation. The "Total Concept of the Mining Industry" (Total Concept) course was placed under its sponsorship. CMAEF is dedicated toward this continuing education program (Table 1). In 1994, the course was streamlined to four-weeks for six hours recertification credit.

Jan 1, 1997

By Heinz Petry

In deep strip mines the job of moving overburden may be so much bigger, and more costly than the removal of coal or ore that the operation is often called dirt mining. Constant improvement in stripping machines and techniques of using them is needed to offset rising costs and to increase production in mines that are now operating, and to make it economically possible to work deeper or thinner deposits.

Jan 1, 1962

By S. Banisi, S. M. Mousavi, S. D. Tafvizi, Gh. A. Parsapour, M. Mahmoudi

Generally, regrind circuits are used to increase the degree of liberation of value minerals which are fed to flotation circuits. At the regrind circuit of the Sarcheshmeh copper complex, four ball mills are in closed circuit with their hydrocyclone clusters. In the initial design of the plant, feed and underflow percent solids, and pressure drop of the hydrocyclones were 39% and 65%, and 15psi, respectively. Over the years, due to a reduction in the feed grade from 1.17% to 0.67% and changes in the operational conditions, the feed rate to each hydrocyclone cluster has decreased from 401 to 70t/h and consequently the pressure drop, feed and underflow percent solids have reduced to 4psi, 17% and 25%, respectively. The main objective of this research was to audit the feed solids concentration and pressure drop of the hydrocyclones and make the necessary modifications based on the Plitt’s model. The results of sampling showed that water recovery to underflow was 59% which was higher than normal values. By reducing the number of operating regrind mills from 4 to 2, the feed rate to each mill increased. After this modification and taking necessary measures in the plant to implement the new operating approach, the pressure drop, feed and underflow percent solids increased to 18psi, 28% and 58%, respectively. The water recovery of the hydrocyclones underflow decreased from 59% to 12%. These changes in addition to increasing the circuit efficiency saved 1000 kWh energy and decreased ball consumption by 925 ton/year because of reduction in the number of operating ball mills. Keywords: Regrind mills, flotation, audit, troubleshooting

Jan 1, 2020

By Thomas Hyatt, Brandon Phetteplace, Camilo Alvarez

A test pile program was undertaken at a project site in Ain Sukhna, Egypt for an import/export oil jetty. Two 1219 mm diameter open ended steel pipe piles were evaluated at two separate test locations. Each test pile was dynamically tested during initial drive utilizing a Pile Driving Analyzer (PDA). Restrike testing was also performed to evaluate the time dependent soil setup. One static compression test and one static tension test was performed at each test location. A correlation of the static and dynamic load test results was established to develop a driving criteria for the piling across the two kilometer project. The constructability benefits of shorter piles will be discussed in more detail, given that the pile lengths were shortened by 9 to 10 meters on average. Lastly, the use of a four pile linear layout to perform both compression and tension tests will be covered. INTRODUCTION With the increased number of Very Large Crude Carriers (VLCC) & Ultra Large Crude Carriers (ULCC) being used to transport oil products around the world, companies and/or nations are presented with the challenge of transferring these products to and from the carriers in deep water scenarios, typically 15 to 20 meter depths, to accommodate the vessels draft. One option for loading/unloading the oil products from a VLCC or ULCC would be to transfer to/from smaller vessels several miles offshore, whereas the most economical option is to unload directly to a pipeline via a berth/jetty platform near shore. These berth platforms must be designed to withstand multiple loading scenarios while these carriers are moored and transferring their products. The use of Large Diameter Open Ended Pipes (LDOEP) piles are a common foundation choice for this offshore application. One of the drawbacks of LDOEP piles, especially across a large project site, is that there can be extreme variability in the pile driving behavior. This can be caused by either a change in soil conditions or the performance of the soil plug. Due to this variability, it is important to verify throughout the duration of the project that the piling is being installed to the correct criteria as established during the load test program. A well designed driven pile load test program, preferably with the combination of Static Load Testing (SLT) and Pile Driving Analysis (PDA), should develop a driving criteria that can allow the contractor and owner to monitor any change in driving behavior.

Jan 1, 2019

By Otis E. Perkins

This paper is one of a series being prepared for the United States Bureau of Mines to disseminate technical information retarding the methods used in mining nonmetallic minerals. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. This paper deals particularly with methods and costs of dredging, classifying materials, and transportation at the plant of the Ross Island Sand & Gravel Co. of Portland, Ore. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of Harold Blake, general manager of the company, and of A. V. Kramer, cashier in charge of the plant office.

Jan 1, 1933

By M. Werner

Mining in the Coeur d'Alene Mining District has been going on for over 100 years with a long- term continuation very likely. Mining is presently carried out at depths below the -5000' horizon. As mining continues at ever increasing depths, higher in-situ rock stresses and subsequent rock deformation is encountered making mining costly and hazardous. To provide access for men and materials in such areas, a wooden raise preparation structure is typically built. Although these structures provide adequate support and access, they have proved to be very costly to construct and maintain.

Jan 1, 1986

By Zhen Lei

In Alberta, Canada, heavy industrial projects are constructed using a prefabrication approach: spools and pipes are produced in the factory, and are assembled into modules that are transported to the industrial plants for installation by mobile cranes. Planning the onsite mobile crane operations is critical to the project budget and schedule. However, due to the large magnitude of industrial projects, manual heavy lift planning is tedious, and the results are not particularly responsive to site changes. This paper introduces an integrated mobile crane management system developed by PCL Industrial Management Inc., in collaboration with the University of Alberta, which investigates crane location selection and path checking for field module assembly. The project information is stored in a database, and the proposed system retrieves data, performs the calculations, and records the results back to the database; the calculations involve automatically selecting locations for the mobile crane, considering the crane capacity, lifting range and utilization. Lift paths for modules are checked for feasibility based on selected locations, satisfying the site and crane configuration constraints, and crane walking paths are planned if needed. The designed system is tested in an industrial project to validate the effectiveness of the system.

Aug 1, 2013

By Zhitong Sui

Based on several case studies on the precipitating behavior of valuable nonferrous metal compounds (VNMC) in molten slags a green technology for the recovery of VNMC from molten slags was proposed. This technology involves three steps: (I) The selective enrichment of the dispersed VNMC into the designed mineral phase in the molten slag; (2) The selective coarsening of the designed mineral phase to a critical grain size in the molten slag; (3) The selective separation from tailing of the grown mineral phase in the solidified slag by dressing or hydrometallurgy processes. This is a clean and low cost technique and has a great capacity to deal with a large quantity of slags. The utilization of the recovered VNMC such as Titanium, Boron, Vanadium compounds was summarized as examples of application. It was confirmed by experiments that the precipitating behavior of the designed mineral phases like Perovskite(CaTiO3), Suanite(2MgO*B2O3) and Sincosite(CaOoV2O5*P2O5) in molten slags is obviously affected by operation factors such as temperature, chemical composition, heat-treatment, additives and so on. The precipitating kinetics and mechanism of the VNMC from molten slags during solidification processes were also investigated.

Jan 1, 2003

By Thornton L. Neathery

The low-grade talc deposits in Tallapoosa County, Alabama, are associated with a mafic-ultramafic rock complex that is part of a widely distributed schist and gneiss group. These rocks form a synform structure overlying Inner Piedmont lithology. Paragenetic sequence of the Tallapoosa talc is interpreted as enstatite-anthophyllitetalc. Talc occurs as massive boulders formed by the alteration of enstatite-anthophyllite and as finely disseminated discrete particles in the enclosing saprolite matrix. Weathered rock reaches depths as great as 60 feet. The quality and quantity of the talc, however, are variable. Mineral analyses of the talc-bearing samples, by petrographic grain count, indicate a talc content of 16 to 26 percent. Most of the talc occurs as plates or scales that are moderately stained with limonite. Fibrous talc also occurs in the deposits and is often mistaken for anthophyllite asbestos which is intimately associated with the talc. The size, shape, and occurrence of the talc deposits precludes any method of min¬ing other than open-cut. A small-scale mining operation began in the district in 1969. Potential capacity of the operation is 5, 000 tons per year. Inferred reserves, based on field investigations, are placed at approximately 8 million tons. Approved for publication by the State Geologist, Geological Survey of Alabama.

Jan 1, 1970

By R. C. Hartviksen, B. H. Boyum

"The Sherman Mine, Temagami, Ontario, is an iron ore pellet operation rated at one million tons per year capacity. Mining is done from three open pits in two bands of Keewatin iron-formation intercalated in a 'greenstone belt' thought to be part of the Archean 'Abitibi Belt'. The bands of iron-formation are tabular and steeply dipping, averaging 75 degrees. The principal ore mineral is magnetite.Blast holes, 1214 inches in diameter, are drilled on 28-foot centers, each hole being sampled and assayed for both total iron and magnetic iron. Concentration tests are made in the laboratory to determine the anticipated concentrate grade. Two classes of ore are recognized -'liberating' or 'refractory'. Blending is done on iron con-.tent, degree of ease of liberation (i.e. grain size) and chunkiness. The latter is important, as primary milling is done in autogenous mills. Actual daily mill results are compared with predicted grade from blast holes, exploration diamond drill holes and pit inspection. Hourly mill samples are analyzed by the X-Ray Fluorescent Analyzer, with emphasis on silica grade. In 1969, the pellet grade was improved from 7 .01 per cent silica natural to 5.50 per cent silica natural."

Jan 1, 1970

By J. M. Floyd

"Top submerged lance furnace developments started in CSIRO in the early 1970s and was given the name Sirosmelt. In the early work the technology was developed for tin smelting and processing tin slags but once a small pilot plant was established other slag processing applications were soon recognised and evaluated for various copper, nickel, zinc and cobalt-containing slags. The process was tried for copper smelting and converting, which was proven in the small pilot plant in 1978. In the same year the first commercial application of the technology was established for the recovery of tin from slags at Associated Tin Smelters, Sydney. Work on lead smelting was initiated by the CSIRO team in the late 1970s and laboratory work led to pilot plant trials by Mount Isa Mines.In the second decade of the technology the focus of development became commercial acceptance of the technology through marketing, development and application by Ausmelt and Mount Isa Mines; the former commercialising and developing the technology for a wide range of applications, while the latter concentrated on its own commercial needs of copper and lead smelting. This decade saw a number of commercial plants built in Australia, with considerable interest becoming evident from other parts of the world. Towards the end of this decade Mount Isa also entered into the business of marketing of the technology through rights dating to the joint work with CSIRO in the late 1970s.So far, after five years, the third decade of the technology has been characterised by diversification of applications of the technology to areas outside the non-ferrous and precious metals production industry. The waste processing and recycle industry and the iron and steel industry have recognised that the top submerged lancing system is a new type of reactor with many significant features which provide new opportunities for processing a range of materials under good environmental controls in a cost effective manner.I hope this audience will excuse my boldness in talking about the third decade of the technology when we are only half way through! I am aiming in this paper to not only talk about the past, but to try illustrate the future directions which I envision."

Jan 1, 1996

By C. H. Grant

The Dew Chemical Company has been engaged in explosives research since 1953. The incentive for this research was based on the desire to find additional markets and uses for magnesium metal of which Dow is a heavy producer. The thermodynamic calculations for explosives incorporating light metals indicate energies approximately twice that of non-metallized explosives currently being used. Early in 1960, we acquired additional patent rights from independent inventors and decided to set up a development station at Virginia, Minnesota, to conduct a commercial testing and market evaluation program with this new product. The actual manufacturing of the explosive was to take place in the bore holes. Due to the complexities involved in controlling the manufacture of the explosive in the bore hole, performance was sometimes in doubt. Furthermore, our experience indicated that the metallized explosive systems could not be evaluated by the standard laboratory methods then being used, and it was necessary for us to look for more suitable research methods. Tests were conducted on several known methods for explosive evaluation. The most promising were the Navy underwater method for energy evaluation, and a modified Livingston crater method intended to compare explosive performance in rock. After shooting over two thousand charges of eight to 60 pounds under water and in taconites and granites with many types of explosives, we have developed a metallized explosive which is now being manufactured at a pilot plant in Virginia, Minnesota, and is being evaluated commercially.

Jan 1, 1963

By Patrick Clark

As part of the Mine Waste Technology Program (MWTP), a large-scale column test using bacteria and a sulfide ore was conducted at McClelland Laboratories, Inc., in Sparks, Nevada. Four technology providers participated in this demonstration. A mining company in Nevada provided the sulfide ore, process effluent and make-up water. A process effluent column, a chemical oxidation column, and the four biological treatment columns were set side by side on a test pad outside the laboratory building. The process effluent and chemical oxidation columns were used for experimental control. The goal of this project was to evaluate the viability and feasibility of using these biodegradation technologies to reduce the cyanide to the regulatory level of 0.2 parts per million (ppm) within an acceptable timeframe and with low operational costs. The column testing began on December 3, 1998 and operated until May 17, 1999. One technology provider reached the regulatory level within the 158 days. The remaining three biotechnology columns were approaching the regulatory limit at completion of the demonstration. The MWTP is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered through an interagency agreement with the U.S. Department of Energy (DOE).

Jan 1, 1998