Search Documents

By E. D. Stephenson

As part of the British Steel Corporation?s development plan during the 1970?s, it was decided to concentrate its bulk steelmaking processes based on the BOS at 4 major Works with access to deepwater ore terminals, for the supply of high-grade imported ores. These 4 sites were at: - 1. Rarenscraig Works in Scotland where the ore terminal would be hilt at Hunterston on the west coast some 50 miles away. Bavenscraig was already an integrated Works but suffered from having to discharge ore 27 Glasgow tenxinus on the River Clyde, which could only accommodate vessels up to 25,000 tonnes. In the future, ore was to be unloaded at Runterston and shipped by a rail-link into Ravenscraig, The new ore terminal would have the potential to unload vessels up to 300,000 tonnes. - 2. Port Talbot Works in south Vales where the existing harbour was developed to discharge large ore carriers. This again was an existing Integrated Works and the benefits of the new harbour also applied to Llanwern Works which was another integrated Works some 50 dies to the east, which would now receive ore from Port Talbot.

Jan 1, 1980

By R. Vracar, D. Sinadinovic, Ž. Kamberovic

The paper presents a study on the oxidation of polymetallic gold ore by oxygen in an autoclave. It presents optimum parameters of autoclave leaching of sulphide refractory ore in self-generated sulphuric acid solutions aiming to get products with favourable technological characteristics from which precious and other useful metals can be recovered. A high partial oxygen pressure (1.5 MPa to 2 MPa), high leaching temperature (190°C to 200°C), pulp density 80 g/L to 240 g/L, ore fraction size 76 µm and leaching time up to 4 hours yield good results in rich ores. The full extent of copper and zinc conversion as well as a high extent of iron conversion has been achieved, while lead, gold and silver and a minor part of iron remain as a solid residue among gangue minerals.

Jan 1, 2001

By T. Braun

A greenfield open pit gold mine in Latin America suspended operations less than three years into an eight-year mine plan after a waste rock dump and heap leach facility sustained substantial damage from a deep-seated landslide. No injuries to employees were recorded because of the slow-moving failure. Due to early detection by the operations team, the owner had sufficient notice of the potential failure and successfully rinsed the heap leach facility prior to the failure event. Engineers estimated approximately 35 million cubic meters of mass movement below the waste rock and heap leach facilities. The original eight-year mine plan produced approximately 60,000 ounces of gold per year. After the failure, the owner terminated gold production, re-configured the mine site to a safe, standby condition and launched a detailed investigation into the root-cause of the failure. Approximately two years after the shutdown, legal interests filed a statement of claim and named three engineering design firms and individuals involved in the project. Several years of litigation, including discovery and deposition proceedings, followed as the legal process considered evidence spanning a 20-year timeline. Changes in project ownership and consulting firms during the development and operations phase complicated the process. In 2017, the plaintiff and last defendant settled. The author was involved as the corporate representative for one of the engineering design firms.

Mar 2, 2022

By Jesse L. Hoyer

A Bureau of Mines turbomill was evaluated for use in the production of high-purity, ultrafine x-Sic powders suitable for advanced ceramics that could substitute for high-temperature alloys containing critical materials such as chromium, cobalt, and nickel. The effect of milling param-eters, such as type of dispersant, temperature, pH, and gas environment, on the milling of x-SiC was studied. The addition of dispersants improved the grindability of x-SiC. Of the six dispersants studied, the best results were obtained with Mara-sperse N-22. Grinding efficiency was also increased when the x-SiC was milled in a basic slurry and at elevated temperature. Gas environments did not appear to affect grinding of x-SiC. Optimum grinding efficiency was obtained at 50° C in a slurry at pH 9.5 with Marasperse N-22 as the dispersant. Under these conditions, minus 100-plus 200-mesh x-SiC was ground to 80 pct less than 1 um in 4 h.

Jan 1, 1987

By Elaine Cristina de Azevedor

Em serviços de radioterapia são utilizados acessórios confeccionados com diversos tipos de polímeros para auxiliar no posicionamento dos pacientes durante o tratamento e na execução das rotinas de trabalho. A radiação gama pode causar nos polímeros degradação de sua estrutura molecular, dificultar a sua na assepsia e seu reduzir o tempo de vida útil. Neste trabalho é apresentado o estudo da degradação causada pela exposição à radiação gama em polímeros utilizados em serviços de radioterapia. Amostras de policarbonato (PC) e polipropileno (PP), foram expostas a doses de radiação gama de 5 kGy e 25 kGy, sendo analisadas por espectrometria de absorção na região do infravermelho e indentação instrumentada. O PC apresentou indícios de fragilização a partir de 5 kGy, reduzindo o tempo de vida útil e o PP apresentou se adequado para o uso em serviços onde haja exposição à radiação gama.

Aug 8, 2018

By William Gleason

"There are signs that the commodity downturn that has battered the mining industry for the past five years is beginning to ease up. As the dust begins to settle and mining companies begin to take stock of the battle, Newmont Mining Corp. will be one that is standing strong with just a few scrapes and bruises thanks in large part to the leadership of president and chief executive officer Gary Goldberg and his right hand man and chief operating officer, Chris Robison.As he closes in on retirement (for a second time) Robison, a third-generation miner from Nevada, took time to speak with Mining Engineering about a 33-year career in which, among other things, he is credited with not just helping Newmont survive the turbulent times but with steering the company to a safer, more productive and more profitable heading.“I think we did it better than anyone else,” Robison said when asked how the company fared during the past five years. “We didn’t talk about it a lot, we just put together a strategy and we delivered.”What Newmont, the world’s second-largest gold mining company by production, delivered since Robison took the position of chief operating officer in 2013 are improvements in costs, porduction, projects and safety.Operating under the mantra of “live within your means,” Robison was pulled out of retirement from Rio Tinto and into a challenging situation at Newmont. The price of gold was in a nose dive from a high of nearly $58/g ($1,800/oz) and heading to levels closer to $38.60/g ($1,200 oz).“Newmont is a big ship that can’t be turned, but has to be steered,” said Robison. “We recognized that we had to set a new course. The direction the ship was going was great for $1,600 to $1,800/oz gold but we were chasing ounces.”Like the rest of the gold mining sector before the falling gold prices, Newmont was focused on volume and was looking for gold wherever it could be found. The slogan at Newmont in 2011 was “7 million ounces a year by 2017.”When Robison came on board it was a different reality.“We had to begin focusing on value over volume as the cornerstone of Newmont going forward,” he said."

Aug 1, 2016

By D. Turk, P. Lefebvre, J. Sargent, K. Major

"Stillwater Mining Company recovers platinum and palladium from their Nye Montana operations. Mining first commenced at Nye in 1987 at a milling rate of 455 t/d (500 stpd). The plant was expanded in 1995 with the replacement of the ball mill and the addition of flotation capacity to increase mill throughput to 1820 t/d (2000 stpd). The applications for platinum and palladium have increased in recent years particularly in the automotive industry and the supply of the metals has remained fairly constant with prices for both platinum and palladium increasing and remaining very stable. In 1997 Stillwater initiated the expansion of their operations to increase production of platinum and palladium. Projects were initiated to expand production at the Nye operations, increase smelter and refining capacities at the Columbus facilities and to develop the extension of the orebody at the East Boulder site. This paper will discuss the changes at the Nye concentrator which were completed to increase production from 1820 t/d (2000 stpd) to 2730 t/d (3000 stpd) and eliminate some of the process bottlenecks.IntroductionStillwater Mining Company is mining the only significant primary source of PGMs outside of South Africa. The J-M Reef is an extensive mineralized zone containing PGMs that has been traced over a strike length of about 43 km (27 miles) in the southwest region of Montana. Stillwater controls the entire PGM mineralized zone.Johns-Manville geologists discovered palladium and platinum in the early 1970’s. In 1979, a Manville subsidiary entered into a partnership with Chevron, USA to develop the project. In 1 987, operations at the Stillwater property near Nye, Montana commenced."

Jan 1, 2000

By Roy Bartholomae

Noise generated by continuous mining machines in underground coal production is an important health hazard. Bureau of Mines Contract J0387229 covers investigation of this noise through laboratory tests of simulated cutting operations and through in-mine noise measurements. The results of these investigations indicate that coal cutting noise and conveyor noise are dominant sources of mining machine operational noise. Typical noise levels for both cutting and conveying operations are approximately 97 dBA (decibels A-weighted). For full operation of all machine systems, the overall sound pressure level is approximately 101 dBA. In-mine and laboratory test results show excellent agreement in both A-weighted overall levels as well as in A-weighted one-third-octave band spectra.

Jan 1, 1983

By José Luis Calderón Jiménez

"Dadas las limitaciones económicas de los gobiernos locales y poco apoyo del Estado, la mina Poderosa recibe presión de la población para cubrir el déficit de servicios que requiere el distrito de Pataz y mejorar la calidad de vida de sus pobladores influencia. En ese sentido, la mina desarrolló un modelo de organización que busca fortalecer las capacidades de gestión y presencia del Estadoa través del proyecto que implica el fortalecimiento de los CODECOS mediante reconocimiento municipal e inscripción en registros públicos y la capacitación a los líderes y autoridades en talleres, pasantías y encuentros con expertos. Así, se mejora la relación con la comunidad de forma sostenible y armoniosa."

Sep 1, 2016

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550'F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550'F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

By Todd S. Harris

"IntroductionThe western region of North America has long been considered a dynamic market supporting such diversified industries as lumber, agriculture, cement, and electronics. In recent years however, the region has also been the focus of a great deal of activity in the extender and filler mineral s business from companies seeking to position themselves to take advantage of the large demand for these materials both here and abroad.Extender and Filler MineralsExtender and filler mineral s include 15different products used in numerous end uses. The nine most important extenders and fillers are listed in Table I. These products range in price from under $50 a ton to over $4,000 a ton and basically represent the following three different types of minerals:Particulate products-Calcium carbonate; Kaolin; Silica.Platy minerals-Talc (Montana, Canada); Mica.Fibrous minerals-Talc (California, Eastern U.S .A.);Wollastonite.What distinguishes these products from other industrial minerals? For one thing, an important feature of extender and filler minerals is that they are used primarily in such consumer non-durable good s as paper, paint, plastics, sealants, and rubber which traditionally do not react as violently to swings in the economic cycle. In addition, these minerals are sold principally on key physical properties, usually brightness, particle size and shape, oil absorption, and hardness. As part of the physical minerals segment of industrial minerals, extenders and fillers are traditionally the most stable group and typically the most profitable. Studies by C.H. Kline over the past decade on extender and filler minerals has revealed historic average profitability (expressed as a percentage on sales) nearly double that of most other industrial mineral s.The demand for these minerals in the western region (Fig. 1), closely follow s the areas of greatest population concentration. These markets include pulp and paper, mainly in the Pacific Northwest, and paint, around Los Angeles and San Fran cisco. Other significant markets for extender and filler minerals in western North America include joint cements, carpet backing, and plastics, mainly PVC pipe."

Jan 1, 1986

By Eric Roller, Elliott Giles

All flyrock incidents have the potential to result in injuries or fatalities that can result in loss of company reputation, license to operate with clients, and bear the exposure to high cost liability. From 2007 to 2009,one NA Quarry and Construction Business experienced a series of flyrock incidents. In the spring of 2009, this business declared that the frequency and severity of Flyrock Incidents had reached an unacceptable level. A Flyrock Elimination Program was launched.

Jan 1, 2012

By Tracy. L. D.

"Since the introduction of pulverized coal as a substitute fuel for natural gas in the various types of heating furnaces used, in steel mills, a number of fires and explosions have occurred, resulting in the loss of life and property.As one of the primary functions of the Bureau of Mines is to conduct investigations in the utilization of mineral substances with a view to increasing safety in the use thereof, it was deemed advisable to investigate the hazards involved in the industrial use of pulverized coal and, if possible, to devise methods of preventing future accidents arising therefrom. The knowledge of the explosive qualities of coal dust which the Bureau has gained in studies affecting dust explosions in coal mines was of material assistance in these investigations.Several plants were visited in which either fires or explosions had occurred, and data obtained as to the probable cause of the accidents.There was found to exist, among some of those employed about the furnaces, a lack of knowledge of the explosive and inflammable qualities of powdered coal.A small stream of pulverized coal leaking down from a defective joint in a coal transport line did not attract much attention, whereas, had a leak in a natural gas line occurred -wider similar circumstances, no doubt it would have had immediate attention.As a matter of fact, if by any means the duet cloud should come in contact with an open flame or hot metal, the effects would be as disastrous as if it had been gas.This is exceedingly well illustrated by an accident which came to the writer's attention. In the system used at this particular plant, the pulverized coal is transported to the furnace through compressed-air lines. The fuel is fed from a storage bin to a blowing tank in quantities as desired, after which compressed air is admitted and the powdered coal blown to the furnaces. At the time of the accident some repairs were being made to the tank, and it was supposed that the air pressure had been entirely released as the pressure gage stood at zero. There was, however, one or two pounds air pressure remaining and when one of the connections was taken off, a cloud of dust was blown across the room, 30 or 40 feet towards the drier furnace where it came in contact with some live coals. Immediately the entire room was filled with flame which rolled back and forth over a specs 50 feet or so in length."

Apr 1, 1921

By Jaiza Bernardo de Oliveira, Iasmim Ariane Silva, Pedro Henrique Medeiros Câmara

The process of manufacturing pig iron in the blast furnace industrial units has the consequence of the generation of slag, a waste that can be produced in high quantity and present damages to the environment, when not reused. In the composition of this tailings, it is sometimes possible to find the presence of metals harmful to nature, such as manganese, which has an important and widespread utility in the metal industries, but still, the slag ends up not being used as a potential source of this element. Knowing this, the slags were subjected to crushing and grading steps to separate the aliquots. These were applied in the tests of technological characterization of the material, from MEV, EDS, Soxhlet and analysis of liberation degree by digital microscope, finding data of several analyzes. Having said that, the objective of this paper is to demonstrate, through the characterization of the slag, that this material has in its composition metallic elements, focusing on manganese, that can be reused in order to avoid the generation of environmental liabilities harmful to the environment. The results show a manganese content with a degree of release greater than 80% in bands from 48 #, which were divided by density and thus allow the gravimetric separation of the material in question.

Oct 3, 2019

By R. A. Haney

The Mine Safety and Health Administration has developed a model to estimate diesel particulate (dp) exposures in underground mines. The estimate uses either in-mine measured dp concentrations or engine manufacturers' standardized emission data and through a series of calculations estimates full shift dp concentrations by applying standard engineering principles of ventilation, control technology and work cycle. This model, in the form of a computer spreadsheet, provides the mining industry with a method to estimate diesel particulate levels and determine the impact of various diesel particulate controls on occupational exposure to dp in underground mines. A detailed description of the estimator and several examples demonstrating the results are provided.

Jan 1, 1998

By Gerry Doeksen

The paper deals with three case studies: (a) the handling of wet concentrates (5 to 8 per cent moisture) through feed bins; (b) the handling of the same product in rail cars; and (c) the handling of dry concentrates (less than 0.5 per cent moisture) through feed bins. In each case, the paper discusses the problems of rat-holing. In each of cases (a) and (c), there is a discussion on the consequent extreme variations of feed rates coming from the feeders, making automation of process control difficult to impossible. Currently available bin-flow theory and flow property tests are used as aids in redesigning the bins. The paper concludes with illustrations of the final results after the redesigned hoppers were installed and tested. There is also a discussion on the advantages of the new mass-flow bins on adjacent feeder performance.

Jan 1, 1970

By K. G. Baxter, D. G. Dixon

The Sepon process plant utilises an autoclave to oxidize a flotation concentrate containing pyrite, residual copper minerals, and sulphur. The concentrate is produced from the residue of a preceding atmospheric copper leaching circuit. The function of the autoclave is to provide iron and acid for that atmospheric copper leaching circuit. The key issues in the operation of the autoclave are to maximise the production of acid and ferric ions and to avoid scaling issues related to sulphur balling in the autoclave. Scale control in the autoclave was examined using various dispersants and residue recycle without success. Operation of the autoclave at high temperature and high acidity addressed the scale issue through rapid oxidation of the sulphur and produced a ferric sulphate precipitate in the residue that could be re-leached to provide ferric iron. This paper presents the development steps followed, through batch and continuous piloting that resulted in an autoclave circuit design that addressed the above process requirements. Following definition of the process design basis, modelling of the autoclave operation was carried out to assist with engineering design. The model included thermodynamics and kinetics of oxidation of pyrite, elemental sulphur and covellite and also considered gas/liquid mixing, oxygen solubility as a function of temperature and solution composition, ferrous to ferric oxidation, gangue reactions with acid and precipitation/re-dissolution of basic ferric sulphate and alunite.

Jan 1, 2004

By John V. Beall

A completed feasibility study executed by an independent agency can benefit a company in two ways. Inside the organization, it verifies the project staffs ideas and their concept of the facility. Outside the company, it can be utilized to obtain equity partners, debt financing, and other forms of credit. It is advisable to bring in a project execution contractor for the feasibility study. A project execution contractor is able to work with engineers to develop the project concept, process flowsheet, and best utilization of the site. By getting an early start on understanding a company's policies and working methods, a project execution contractor saves the company money since it does not have to go through the educational buildup twice. The contractor is a specialist in putting together a bankable document that can be taken to a financing source. It answers all the agency requirements on the first pass. In addition, the contractor can advise an owner on likely financing sources since he works on the worldwide market every day. A less obvious advantage of including the contractor in the study and predevelopment buildup stages is the importance of coordinating finance and technical input. The financing source influences equipment specifications, procurement, logistics, project schedule, cash flow, and liquidity. There are many surprises in store for any manager of a large international project involving worldwide financing and purchasing. The job does not have to be made more difficult by bringing in a contractor after all predevelopment steps are taken. The contractor can still work if the predevelopment steps have been done, even if he does not agree with them. But early contractor involvement is the preferable solution.

Jan 10, 1980

By Walter Herd

FoR the past eight years No. 2 mine of the Cumberland Railway & Coal CO., Springhill, Nova Scotia—a subsidiary of the Dominion Coal Co., Ltd.—has had an unenviable reputation for bumps. As the workings extended in certain directions under a greater cover, these bumps increased in severity and it became apparent that some change in the system of extraction was necessary if the mine was to continue to operate. In September, 1924, following several fatalities resulting from bumps, the Mines Department of Nova Scotia requested from the U. S. Bureau of Mines the services of George S. Rice, Chief Mining Engineer of the Bureau, to report on the conditions then prevalent in No. 2 mine, Springhill. This request was promptly and courteously granted. Mr. Rice made a full investigation and a comprehensive and helpful report, which is embodied in the 1924 Annual Report of the Department of Public Works and Mines, Nova Scotia. Prior to 1925, the room and pillar method was employed and in January of that year (there being a cessation of work from March to August due to labor troubles) longwall retreating on the west side, on a limited scale, and in a small section on the east side of the mine was started. The major portion of the east side was not operated on this system till August, 1926, as there was developed a considerable area ready for pillar extraction between an arbitrary boundary and a point up to which bumps of any consequence had not been experienced. In the interval development work for longwall retreating below the 5900-ft. level was vigorously pushed. This longwall retreating system was suggested by Mr. Rice as a possible remedy and was heartily endorsed by the company officials. This paper describes the conditions and happenings subsequent to Mr. Rice's report and more especially the results with the longwall retreating system of mining under the peculiar circumstances pertaining to mining No. 2 Seam, Springhill, at depth, and records the conclusions which experience with several severe bumps under this mode of extraction would suggest. Except where necessary to make the paper intelligible as an entity any duplication of Mr. Rice's report will be avoided.

Jan 1, 1930