Search Documents

By James J. Dawd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the ninth of a series of reports giving results of studies by counties under part (1) of the investigation. (See Appendix.) This report covers Raleigh County, W. Va., which comprises parts of Bald Knob, Eccles, Beckley, Meadow Creek, Mullens, Flattop, and Big Bend quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, location of drill holes, bed and total coal thickness, and outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas. areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps, Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952

By J. E. De Waele, J. J. Lee, M. J. Mulheron, Luke R. Deamer

There is increasing demand for geotechnical contractors to commit to carbon reduction, net zero or science based targets. A lot of focus has therefore been placed on using low carbon materials and low emission rigs. However, whilst these are ways to help reduce carbon, there is a need to look beyond just substituting materials and fuels to meet net zero. Using the IEMA carbon hierarchy, there is a need to first look at eliminating and reducing emissions, before considering substitute materials. For example, in geotechnical designs, this may mean considering using ground improvement or reducing the number of piles, before considering using low carbon cements. Equally, for remaining emissions, this hierarchy means considering carbon negative products to offset emissions, such as ground source heat pumps. This hierarchy can also be applied throughout geotechnical contractor organisations. For example, considering video conferencing for meetings, before considering public transport or using an electric vehicle. This article explores the carbon hierarchy and how it can be applied to all areas of a geotechnical contractor’s business. Only through embedding this hierarchy across the business can geotechnical contractors achieve the step change required to meet net zero.

May 1, 2022

By Daniel Bloomfield

ONE of the major problems of management is how to restore in some measure the personal relation-ship between employer and employed which, in the days of small concerns, meant better morale among employees. The complexity of industry today, the heterogeneous mass. of workers employed, many .of them new to this country and to its institutions, the inability of those whose task it is to get out production to spend much time on the problems of labor-all these and many other factors serve to make of great impor-tance the question of how to establish more satisfactory mutual good will. While there is no such thing as a sure cure for labor troubles, in spite of the fact that charlatans have been selling alleged cures to guileless employers, study and experience have brought to light methods of approach to the problems confronting management in its relation to labor that are well worth consideration. Labor problems must be approached with common sense and an open mind. Facts must be the basis of action. So it is with the question of morale in industry. What makes or breaks morale? What are the forces behind the actions of men? What is there in one man that makes him act differently from another man under similar circumstances? How are men affected by the actions of others in their own group or by the actions of those under whose supervision they work? These are questions that must be carefully studied if we are, to get at the bottom of industrial unrest. It is an easy thing to say that good will can be created by "treating men right." That involves so many things and points of view that it will hardly serve as a full answer to our problem; but it is a good starting point if we mean by right treatment the payment of wages consistent with the well being of the worker and his family as members of the community, and if we also mean the provision of sanitary, wholesome working conditions and a working schedule that does not overtax the worker physically, and mutuality-a give and take relationship. With this as a basis we can go a step farther and see what else can be done to promote better relations between management and the workers.

Jan 9, 1922

By Louis Frost

"Dominion No. 17 Colliery, of the Dominion Coal Company, Limited, is located in the district of New Victoria, N.S., at the entrance to Sydney harbour.This Colliery was opened in 1882 to work a submarine area of the Harbour seam (see Figure 1). It was closed in 1921 and the mine, which has a make of water of approximately 250 gallons per minute, was allowed to fill.No. 18 Colliery, situated almost a mile to the east, was opened in 1938 to work the Phalen seam in this area with the intention, later, of driving a cross-measure tunnel to mine the section of the Harbour seam lying between No. 17 Colliery and the Princess Colliery of the Nova Scotia Steel and Coal Company, Limited.In 1945 it became necessary to open this area in the Harbour seam and a cross-measure tunnel was driven from the existing workings of No. 18 Colliery in the Phalen seam, which underlies the Harbour seam at a depth of 500 feet.The tunnel was started in 1946 and completed in 1948. The cost of opening this section, which contained only 6 1/2 million tons of coal, made imperative the recovery of all the available coal and precluded the maintenance of the large barriers that had been left in No. 17 Colliery for impounding the water, especially as the maintenance of these barriers would have meant the loss of 885,000 tons of coal, or 12.3 per cent of the whole tonnage available. Therefore, a study was made to determine the best means to dewater the 250 million gallons of water lying in the old No. 17 Colliery."

Jan 1, 1952

By Julia Pflieger, Manfred Russ, Johannes Gediga

This paper shall show an economic feasible approach to implement Greenhouse Gas (GHG) reduction measures into the mining and metallurgy industry. The goal to improve energy consumption is directly linked to the reduction of GHG emissions and therefore directly in correlation with the economic viability. A baseline scenario of the considered reference system and of the respective reference year has to be defined, mapped and analysed. In a second step an analysis of the same operation using available and prospected Best Available Technology (BAT) processes is carried out to generate a basis for a benchmark system. The identified reduction potentials are reported and the GHG emission reductions are put into relation to the investment cost of the new process technologies / process adaption to be implemented. This economic feasibility calculation is necessary to realise a cost efficient GHG reduction roadmap implementation into the company's business operations. The GHG reduction roadmap is developed using ratios between GHG reduction and investment / operating cost to get an indication for a sequence for implementing carbon emission reductions measures.

Jan 1, 2010

By M. Handley

The Witwatersrand Basin contains by far the most gold ever found, and has hosted mining from its discovery in 1886 to the present. For many years, South Africa was the world’s largest producerof gold, nearly all of which came from the Witwatersrand. Since 2000, South Africa has fallen back several positions because of declining gold output. There are many complex and varied reasons for this; however, declining gold resources in the Witwatersrand Basin are not one of them. As far as the author knows, there are no qualified estimates in the literature of gold remaining in the Witwatersrand Basin. This paper collects mining data from several sources and then, using elementary gold accounting and error analysis, attempts to estimate the amount of gold remaining in the Witwatersrand Basin. It includes gold underground in existing and defunct mines, in evaluated ore resources, and dumps. Compiled data from 1887 to 2019 shows that 50 200 t of gold were produced by Witwatersrand mines, while it is estimated that a further 48 100 t remainunderground, both within and outside of mine leases, a further 1 600 t on the surface in tailings,and an unknown amount in rock dumps. Nearly all of this gold will remain inaccessible with current mining methods, and major technical developments in mining will be necessary before any of the gold can be categorized as a code-compliant resource or reserve. To win this prize, the mining industry will have to rethink its approach to mining, both in old mining leases and in the unexploited ground. It will also have to find effective means of preventing gold theft and informal mining, which are on the rise.

Apr 5, 2023

By T. A. Klinefelter

ONE OF THE many services rendered by the Federal Bureau of Mines is the identification and general examination of ore and mineral samples. Many of these, coming from almost every State in the Union, are clay and shale samples. Other Government agencies, State geologists, universities, and other laboratories are often requested to make similar examinations. This publication describes methods of testing these samples. An earlier paper, published in 1943, described Bureau of Mines methods of testing such clays.3 This paper was to be followed later with another (part II) that would describe much more thorough testing than did the rather general outline of part I. Part I has been out of print for some time and needs revision, and part II was never written; hence, the present publication is designed to include part I and also those additions intended as part II. The tests presented in part I were simple, requiring only the ordinary equipment to be found in any good chemical laboratory. The second publication was to include a greater number of test procedures and information on increasing the accuracy and precision of those previously given.

Jan 1, 1957

By P Micale

Geological data provides the foundations for the mining value chain. It is used to underpin the modelling and planning and consequently optimise downstream business decisions. However, it is often forgotten or taken for granted. End users often assume the data to be sound without verification. Geological data can be considered a company’s number one asset. Subsequently, the storage, use and management of this data need careful curation and time invested in preserving and protecting it. An established polymetallic mine with 20 000 drill holes could have a data replacement value in excess of $500M at 2020 prices, excluding labour and salary costs. The Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (the ‘JORC Code’) provides guidelines for Public Reporting. Within the code, Table 1 requires discussion around the different types of geological data, its collection and use. What is needed is additional details regarding the validation and integrity of the geological database. A comprehensive guideline specifying minimum geological standards for geological databases has been developed. This expands on the critical points outlined in Table 1 of the JORC Code. This guideline can be used by companies where geological databases are managed in-house or used to assess these services’ outsourcing. This guideline will ensure that geological data is reliable and unadulterated and can be used with confidence. Using this guideline will assist in preserving the investment of geological data in the mining value chain

Mar 22, 2022

By F. Louis Grammer

The following study of flue-dirt and the influences controlling it may be interesting to many. It is published because it represents observations at about thirty furnaces at different times. It may assist in giving an impetus to the making of similar observations elsewhere. Until ten years ago, the metallic waste in furnace-gases was not considered a problem of pressing urgency in iron metallurgy—certainly not in the blastfurnace end of it. Many plants at present ignore, or pay but little attention to, top-pressures. Prior to the introduction of Mesabi ore, the losses in escaping gases, if considered at all, were regarded as thermal losses, or losses of fuel (except by those interested in lead, zinc, silver, etc.). In a high-priced material like ferro-manganese, such losses were, indeed, considered important. But the behavior of the Mesabi ores, corning, as they did, in practically inexhaustible quantities, could not be disregarded by the furnaceman. These ores came to stay. The tables appended below have purposely been altered to disguise the plant, the company and the ores used. The comparative values are maintained. In these tables, the influencing elements and conditions which are constant, or practically so, namely, size of furnace, quantity of wind, fuel used, etc., are not mentioned. The figures represent observations consistently followed up for a long period. The weights of flue-dirt were obtained from cars on which no other dirt was thrown. The analyses and calculations are based on the best of sampling. The effects of slips are excluded. Slips should not occur at well-regulated or properly-constructed furnaces, excepting under unusual and rare conditions. Allowances are made for moisture, scrap charged and silicon in the metal. The cutting effect of Mesabi

Jan 1, 1904

By Y. C. Kim

The strongly skewed grade distributions and the need to estimate the local recoverable reserves in a selective mining environment are the two problems that Ordinary Kriging (OK) cannot easily handle. With the recent introduction of the nonparametric, distribution-free technique of Indicator Kriging (IK), the above problems can be solved. This paper describes the results of performance evaluation of IK in an open-pit gold-silver deposit. For performance evaluation, the predictions of local recoverable reserves using IK were compared with the actual reserves based on blast hole information. The IK estimator, although a bit optimistic, performed very well in predicting the total recoverable ounces of gold from each panel on a test bench. The OK estimator was also used to try to predict local recoverable reserves, by treating each panel as either waste or ore, depending on the panel's average grade. Under this criterion. OK was found to be very biased and pessimistic.

Jan 1, 1986

By K. H. Coats, M. H. Terhune

Analysis and example applications have been performed to compare the accuracy and computing speed of alternating-direction explicit and implicit procedures (ADEP and ADIP) in numerical solution of reservoir fluid flow problems. ADIP yields significantly greater accuracy and requires about 60 per cent more computing time than ADEP, not 300 or 500 per cent more as reported elsewhere. l,2 INTRODUCTION Several recent papers 1-3 discuss an alternating-direction explicit difference approximation (ADEP) to the diffusion equation. Example applications of ADEP and ADIP4 were reported to support conclusions that ADEP is comparable in accuracy to ADIP and requires one-fifth to one-third the computing time of ADIP. Applications of ADEP in calculation of two-phase flow in reservoirs was also proposed. 3 This study was performed to compare further the relative merits of ADEP and ADIP in simulation of two-dimensional flow of one and two fluid phases in reservoirs. Since two-phase flow equations are often essentially elliptic rather than parabolic, the efficiency of ADEP in solving the elliptic equation was also examined.

Jan 1, 1967

By C. B. DUTTON, W. F. RITTMAN, E. W. Dean, M. S. HOWARD

NOMENCLATURE USED IN THIS REPORT. In this report the ending ene has been used throughout, except in the bibliography and in quotations from the writings of previous investigators, for all aromatic hydrocarbons, as, for instance, benzene, toluene, xylene. The ending ol, though largely used in technical description, is not correctly applicable to these hydrocarbons, and should be used to designate the impure mixtures of commerce, as distinguished from pure chemical compounds. PRESENT STATUS OF PETROLEUM-REFINING INDUSTRY. Although petroleum is widely distributed, being found in many parts of the world, and although information as to its occurrence and general characteristics seems to have existed from vcry early times, our knowledge of the chemical nature of this substance has been acquired largely within the past 40 years. Within this period a voluminous literature has accumulated, which records work as painstaking as has ever been undertaken in the whole field of chemistry, such as that of C. M. Warren, F. H. Storer, S. P. Sadtler, S. F. Peckham, and C. F. Mabery. Despite this fact, the commercial method of treating crude petroleum for the purpose of procuring marketable products is, in the main, essentially empirical. Much knowledge has been acquired as to methods of separating from crude petroleum such products as are desirable commercially, but little has been done to attain the maximum recovery of such products.

Jan 1, 1916

By Dominic Howarth, Diana Drinkwater, Don McKee

"The pressures on mining and minerals education at the tertiary level are well known. Within Australia, for example, the number of undergraduate mining engineering courses with 30 or more students in each year has reduced to three (University of Queensland, University of New South Wales and Curtin University). Similar declines in both student numbers and participating institutions are evident in many other parts of the world, and notably in USA and most countries in Europe.An in depth study of the Australian sector was conducted in 1997/1998, resulting in the Back from the Brink report (Carter 1998). The Australian situation was summarised as follows.Australia’s minerals education system, in its current form, is fragile and is in no position to seize the opportunity (i.e. world leadership in minerals education) and is more likely to succumb to the threat.Current trends include:- an acute shortage of talented academic staff, as a result of University remuneration packages having become hopelessly uncompetitive with those in the minerals industry;- small student populations and high relative costs, making mineral specific courses vulnerable to closures, when Universities are under extreme cost pressures; this situation will be exacerbated if enrolments drop in response to, say, a cyclical down turn in the industry; and- under-resourcing of minerals departments because of their comparatively small size, making these departments incapable of delivering top class teaching in all aspects of their courses, despite being excellent in some areas.Most of the Australian issues identified above have direct parallels in other countries.The most common response of institutions to the threats is to seek strength, and in some cases survival, through various forms of linkages and networks. A number of these associations, which are frequently defensive in nature, are outlined in the paper."

Jan 1, 2003

When it comes to safety in the mining and extractive industries, success is literally a matter of life and death. Anything short of perfection is not acceptable. In recent years, the mining industry in the United States has made tremendous strides in terms of health and safety for its workers. Part of that success has come with an increased focus on the issues of safety, an intense examination of procedures, liberal sharing of best practices and a focus on the synergy between safety, reliability and environment. During his closing keynote address of the Safety Management & System Reliability Conference in Minneapolis, MN on Nov. 15, Joe Driscoll, vice president of Great Basin Gold, showed a calendar from the coal fields in Pennsylvania from the early 1900s. The calendar marked the number of mine-related deaths each month. Some months, the number was as high as 50. It was an illustration of how far things have come, but there is still much more work to be done.

Jan 1, 2013

By Francis F. Pitard

The presence of elements, minerals, or chemical compounds in materials at very low concentrations is becoming a constantly increasing concern for several segments of the Industry. Some trace elements or chemical compounds may be considered as hazardous, some are simply considered as undesirable In complex processes where they could be constantly recycled and end up as the major factor of decreasing quality for some valuable products. In some other cases, the presence of a trace element or mineral may be highly desirable because of its economical value: precious metals are falling into this category, they probably were the first trace elements to draw our attention. Tremendous quantity of money is spent for analysis at the trace level, also the analytical "tool" has been considerably improved during recent years, but still the sampling aspect of the problem remains obscur for many, and because of it, large quantity of analytical efforts become meaningless. Not only the absence of sampling strategies is badly affecting the representativeness of a large majority of samples, but furthermore for the same reasons, many laboratories are failing In their endeavor to prepare reliable standard reference materials. The reason of this failure has its roots in the unability to estimate effectively the sampling characteristics of the element, mineral, or compound of interest, not to mention the unability to perform precise and accurate complete analysis, so essential for the instrumental analyst (1). In this paper a strategy to perform a better sampling operation is recommended. SELECTION OF A PROBABILISTIC APPROACH AS SOON AS PRACTICALLY POSSIBLE It Is essential to differentiate probabilistic sampling from non-probabilistic sampling. As Illustrated in Figure 1, the sampling operation Is a selection process which could be performed In two different ways: I. A probabilistic selection process according to which all elements of a lot of material to be sampled are submitted to the selection with a same probability of being selected. 2. A non-probabilistic selection process according to which all elements of a lot of material to be sampled are submitted to the selection with different probabilities of being selected.

Jan 1, 1986

By J. Marc Coolen

Marrowbone Development Company operates a large drift mining complex in the central Appalachian coal field. In 1997, five continuous miner supersections produced close to 9 million tons of raw plant feed. All production is from the Coalburg seam, a 5 to 10 ft thick coal seam with multiple coal benches and shale binders. The immediate roof lithologies consist of laminated shales, sandstones, or a mixture of sandstones and shales. The mine area is bisected by the regional Warfield anticline and associated Warfield fault. Mining conditions vary considerably due to frequent changes in seam and roof geology. The following geological categories can be distinguished: 1) presence of coal riders in the immediate shale roof, 2) excessive seam slopes around the Warfield fault, 3) splay faults associated with the Warfield fault, 4) zones of abundant slickensides, 5) abrupt roof lithology changes (sandstone - shale), 6) splitting and merging of different benches of the Coalburg seam, 7) sandstone washouts, 8) excessive roof dilution, 9) pillar sizing problems due to seam anomalies (soft fireclay binders). Several examples of these features are discussed in detail. Also, their relationship to roof fall occurrences is evaluated. Early recognition of potentially adverse geological conditions is of prime importance for the economic viability of the mining plans. Detailed core drilling in advance of the mining faces and coordination of the core data with underground mapping are the main forecasting tools.

Jan 1, 1999

The VoD of non-ideal explosives depends on the charge diameter and the thickness, strength and sound velocity of the confiner. VoD measurements are made to evaluate explosives for development, quality control and prediction of field performance. In testing, the container is part of the explosive system and affects the measured VoD. Pipe testing in cardboard tubes delivers the best guide to unconfined critical diameter and minimum VoD range, but the thickness of the pipes affects the result close to critical diameter, even in emulsions. PVC pipes are not good for unconfined test work because they provide relatively strong confinement. Care must be taken to select pipes with constant relative pipe area across the range of diameters. Where pipes are used to evaluate the effect of confinement, the ratio of the wall thickness relative to the thickness of the detonation driving zone in the explosive needs to exceed 0.5 to create full confinement and the ratio of the detonation velocity to the confiner wave speed must be considered. Estimates for critical thicknesses are provided from Non-Ideal detonation models. The relationship between confinement modulus and VoD is discussed and indexes are suggested for quantifying the explosive performance.

Jan 1, 2007

By John F. Kearney

After World War II Canada?s fledgling iron ore mining industry developed along the ill-defined Quebec / Labrador border near what became the town of Knob Lake and later renamed Schefferville. For about twenty-five years from 1954 to 1982 Schefferville was the epicenter of Canadian iron ore mining and the foundation of the Iron Ore Company of Canada. In about 1982 it all stopped, shut down, the miners moved away leaving behind a mining camp and a ghost town that have sat idle and almost deserted for the past twenty five years. The story looks set to change with new plans to re-establish the former mining operations in the historic mining camp. This paper outlines the proposal to reactivate the direct shipping iron ore operations in the Schefferville mining camp, and specifically the properties in Labrador owned or optioned by Labrador Iron Mines Limited (?LIM?), a wholly owned subsidiary of London Stock Exchange listed Anglesey Mining plc. The Schefferville mining camp is located about 1,000 km northeast of Montreal. There are no roads connecting the area to southern Labrador or to Quebec. Access to the area is by rail from Sept Iles to Schefferville, or by air from Montreal and Sept Iles.

May 1, 2007

By T. E. Masoner

The struggle to get the minerals industry seriously interested in high intensity wet magnetic separation* has been difficult. The high capital cost of the equipment, the lack of basic research, the lack of operating information, and the diverse characteristics associated with different minerals and ores have prevented the development and use of HIMS-W on a wide scale. The Climax Molybdenum Company, a Division of American Metal Climax, Inc., located at Climax, Colorado, was among the first companies in the Americas in recent years to support the development of HIMS-W to recover weakly magnetic minerals on a large scale. The Climax Molybdenum Company, one of the world's largest underground mines, processes about 40,000 tons per day of ore, from which about fifty million pounds of molybdenum disulfide are produced each year. By-products include tungsten, iron pyrite, tin, and some monazite.

Jan 1, 1968

By Staff

This paper contains an outline of the history of the Sullivan mine, now owned and operated by the Consolidated Mining & Smelting Company of Canada, Ltd.; some account of the various methods by which the ore has been treated in efforts to solve the metallurgical problems which its complex character presents, and, finally, to give, as concisely as possible, an outline of the present mining and metallurgical practice along with a description of the mining and milling plant at Kimberley and the smelter and refineries at Trail, in British Columbia. EARLY HISTORY In May, 1892, Pat Sullivan, John Cleaver and Mike Holland left the Coeur d'Alene country, in the State of Idaho, to seek their fortunes in the Kootenay lake district in British Columbia. They were aided in their venture by James Cronin, afterwards locator and owner of the St. Eugene mine at Moyie. Two months later the party broke up, Sullivan and Cleaver crossing the mountains from Crawford bay on Kootenay lake to the head waters of the St. Mary's river, the course of which they followed down to Fort Steele. Here they found a good deal of excitement about the North Star mine, and, joined by "Ed." Smith, who was familiar with this part of the country, they determined to return and prospect in its vicinity.

Jan 1, 1924