Search Documents

By S. H. Ash

The coal-mining districts of Washington are mainly situated west of the Cascade Mountains. The eastern boundaries of Whatcom, Skagit, Snohomish, King, Pierce, and Lewis Counties, shown in Figure 1, form the backbone of the mountain range. The mines are on the foothills of the slope and extend to the shores of Puget Sound in the central and northern portions. The subbituminous fields of Lewis, Thurston, and Cowlitz Counties extend into the valleys west of the mountains. The Roslyn field, a small but important area, Lies on the eastern slope of the Cascade Range. If western Washington is divided into three areas from north to south the bituminous coal fields and most of the active mining operations will be found largely in the central area. In the southern portion there are large areas of subbituminous coals of varying quality extending from Centralia to the Columbia River. In the northern portion, mining is at present practically restricted to one mine which is working a subbituminous bed near the city of Bellingham.

Jan 1, 1931

By B. Simser, T. Butler, A. Hall

The longterm future of Glencores’ mining operations in the Sudbury basin area of Ontario, Canada likely depends on mining deposits at depths below two kilometres. To gain a better insight into the rockmass response to mining, a geological scouthole program has been implemented at Glencores’ Nickel Rim Deep and Onaping Depth Project to gain insight into rockmass conditions ahead of the devel-opment face. The scouthole program involves drilling long (up to 600 m) subhorizontal boreholes drilled ahead of the development end and collecting data about the rockmass conditions from various geophysi-cal and mechanical tools (in addition to conventional core logging). Once all data has been collected and the borehole is available, seismic sensors are installed up to 450 m down the hole as part of the micro-seismic monitoring program with the leading sensor always located ahead of the development end. The recorded seismic data is used to provide realtime insight into the rockmass response to mining. On May 20, 2017 a flurry of seismicity with a maximum moment magnitude (Mw) of 0.7 occurred causing damage to the ramp heading. Data from the microseismic monitoring system had indicated that conditions at the development end were changing prior to the rockburst. A back analysis of the scouthole data indicated a clear anomaly in the rockmass at the location of the rockburst. The scouthole data also provided sufficient information to suggest that once this anomalous zone was exited, mining conditions would improve. With the microseismic monitoring system providing realtime information from the rockmass, the area was re-habilitated and ramp development continued successfully. Details of the rehabilitation and adjustments to the ramp development are discussed. Some correlations between the scouthole data and recorded micro-seismicity are also presented.

Apr 26, 2022

By J. J. Forbes

Probably the newest thing in mining safety, or safety for mines, is the apparent dissatisfaction on the part of the mineral industries, as represented by both management and labor, and the general public of the Nation, with the safety record of the mining industry. This is reflected by published comments and papers in the technical press;1-8 in labor periodicals, 10 11 in popular journals and periodicals,12 13 and in the daily press; also by discussions of the Safety Committees sponsored by the National Safety Council, 9, 14-15 the American Mining Congress, 1, 16 the American Institute of Mining and Metallurgical Engineers, 2, 4 the Mine Inspectors' Institute of America,6,8,17,18 the Coal Mining Institute of America, 5, 19, the American Standards Association, and others.20,21

Jan 1, 1949

By Galen H. Clevenger

Although there are exceptions, oxidized silver ores containing the higher oxides of manganese are generally refractory to hydrometallurgical methods of treatment. When these ores are of high enough grade they can be smelted; indeed, some rather low-grade ores of this type have been smelted at a profit because of their fluxing value. In the past, when these ores could not be smelted, they either were not treated or were treated at low efficiency, generally by cyanidation. The need for thorough investigation of the problem was therefore evident for some time before the writers began their research. The problem of treating manganese-silver ores seems to have been recognized first about 35 years ago by C. W. Goodale in applying pan amalgamation at Tombstone, Ariz. He attributed the low extraction of silver to the fouling of the mercury by manganese rather than to the presence of a refractory compound of manganese and silver. Although definite knowledge as to the cause of the poor extraction of silver was lacking, a more or less effective preliminary treatment, that is, a chloridizing roast, was applied.

Jan 1, 1925

The 28th annual American Mining Hall of Fame Awards Banquet and fundraiser sponsored by the Mining Foundation of the Southwest will be held at the Marriott University Park Hotel, Tucson, AZ on Saturday, Dec. 4, 2010. The Mining Foundation of the Southwest is a nonprofit organization whose objectives are public education about the mineral industries, and recognition of outstanding accomplishments in and contributions to the fields of mineral and fuel resources. Funds are being raised to the support the foundation?s educational programs. Among these is the Educational Outreach Program operated jointly by the foundation and the Arizona Department of Mines and Mineral Resources.

Jan 1, 2010

By Aleksandar D. Bugarski, Dylan A. Ritter

The results of laboratory characterization of tailpipe emissions for three “clean” engines that meet U.S. EPA Tier 4 final emissions standards were used to assess the viability and effectiveness of repowering existing engines and powering new mobile equipment with those engines as a control strategy for reducing exposure of underground miners to diesel aerosol and criteria gases. The evaluated engines were representative of those that achieve the emission standards through implementation of various in-cylinder emissions control strategies, use of crankcase filtration, and use of three types of exhaust aftertreatment systems: (1) diesel oxidation catalytic converter (DOC), (2) combination of DOC and the full-flow wall flow monolith diesel particulate filter (DPF), or (3) combination of DOC, diesel exhaust fluid (DEF) based selective catalytic reduction (SCR) system, and ammonia slip catalyst (ASC). The study showed that the highest reductions in concentrations of diesel aerosols in underground workings, in terms of both mass and number, could be achieved if the engines, preferably in all power classes, are fitted with viable DPF systems. The use of U.S. EPA Tier 4 final engines equipped with DOC and DOC/SCR/ASC systems could help operators to considerably reduce mass, but not number concentrations of aerosols. The emissions of two of the evaluated engines, one equipped with DOC and the other equipped with DOC/DPF systems, were characterized by substantial secondary NO2 emissions that would limit the viability of those engines for underground mining applications. It appears that the catalyst formulations used in the exhaust aftertreatment systems of the “clean” engines marketed to the underground mining industry need to be formulated to minimize the potential for generation of secondary NO2 emissions. The results indicate that the engines fitted with viable SCR/ASC systems present a low-NO2 alternative. All three “clean” engines were found to have low CO output. Therefore, due to nuances associated with the use of diesel-powered mobile equipment in underground mines, special attention needs to be paid to the selection and potentially optimization of “clean” engines for underground mining applications.

Feb 1, 2025

By Michael K. Phang

The use of explosives to fragment rock generates ground vibrations which may have a detrimental effect on contiguous underground coal mine openings. Increased surface blasting by a burgeoning number of surface coal mines and quarries has caused considerable concern among underground mine operators. Ground vibration effects generated from surface mine blasting are also causing public concern. In response to this concern, the U.S. Bureau of Mines (Stagg and Engler, 1980) has measured and analyzed ground vibrations and their effects on underground and surface structures. Some of the complaints registered against the mining industry are claims of substantial material damage from vibrations generated by the blasting; others are nuisance complaints of minor damage or annoyance. In general, allegations of damage from surface blasting have been sufficiently numerous to constitute a major problem for mine operators engaged in blasting operations. They have recognized the need for more technological data to evaluate the vibration problems associated with blasting. Both the operators and the general public need adequate safeguards based upon factual data to protect their specific interests. The coal mine industry needs reliable information from which to change blasting operations to reduce the number and severity of major damage claims and eliminate the growing number of nuisance complaints. The problem is of major concern not only to coal mine operators and nearby property owners, but also to federal, state and local governments. At the same time, environmental control agencies responsible for blasting and explosives use require reasonable and appropriate guidelines to protect the miners' lives.

Jan 1, 1984

This volume constitutes the final report for the Rescue Subsystem portion of the Coal Mine Rescue and Survival System program conducted by the Westinghouse Electric Corporation under contract to the United States Bureau of Mines (Contract Number H0101262 dated Jung 17, 1970). The program was directed by the Special Systems Department of the Westinghouse, Baltimore, Maryland facility. The basic objectives of the CMRSS program were to develop and test hardware to determine the efficacy of a variety of coal mine rescue and survival concepts and techniques. These concepts were drawn from two major- sources: the Request for Proposal from the Bureau of Mines and the final report on the Mine Rescue and Survival Study conducted by the National Academy of Engineering (NAE).

Jan 1, 1971

By D. M. Hausen

Microscopic point-counting of polished sections, in combination with x-ray diffraction analyses of representative whole rock samples, provides an efficient means to compare the modal mineralogic composition of different rock types. Major gangue minerals, e.g., quartz, feldspars, micas, amphiboles, chlorite, clays, etc., are estimated semiquantitatively by x-ray diffraction techniques, utilizing optimum grind, gridded sample surfaces and a sample spinner during scanning. Opaque to semi-opaque oxide and .sulfide phases are estimated by microscopic "point-count" and "gross-count" scanning. Total mineralogic compositions are calculated and normalized to 100 percent from XRD and microscopic data by computer programming. Comparative mineral analyses for different rock types, as well as quantitative microscopic data for various parameters, including particle and crystal sizes, textures, degree of alteration, paragenesis, etc., provide useful guides in mineral exploration, both in early stages of geologic mapping and later stages of economic evaluation. Several case histories are described.

Jan 1, 1981

By E. L. Oliver

IN OFFERING a few comments and suggestions on trends in mining practice, and the methods and tools of tomorrow's mining, perhaps it will be appropriate to start with the subject of education. Charles Kettering, one of the best-known scientists and experimentalists in the automotive industry once said, in effect, that tech- 111ca1 schools have to be carefid not to teach a lot of hard and fast rules that may have been true once, but aren't so any more, or won't be presently. Possibly the mining school of the future will concern itself less with what has happened and more with what is going to happen. It will be built about or around problems. Such a school will be judged, not by the number of its students but by the quality of its improvements. To such a school the industry will send for men to solve particular problems. The industry will doubtless at some time sup- port such a school financially though a lot of hard work will be required to organize miners to undertake such financing, primarily because the mining industry, other than that concerned with iron and steel, is too loosely knit. Each company tends to its own knitting too closely for its own good. Wouldn't it be splendid if the mining industry would finance a "problem school" as suggested by Mr. Kettering and others.

Jan 1, 1939

Surface mining and reclamation of a southeastern Ohio site with sandstone-shale overburden resulted in (as compared to premining levels): 1) runoff volumes and peak rates that increased by a factor of from 2 to 10 during mining and after reclamation, 2) destruction of the "aquifer" perched on the underclay of the mined coal bed and gradual, but, as yet incomplete redevelopment of this aquifer after reclamation, 3) no immediate effect on another, lower perched "aquifer", 4) up to 100 times greater sediment concentrations in runoff. Results were influenced by increasing annual precipitation amounts through the period of record; 1978, 1979, and 1980 (postreclamation years) experienced precipitation amounts approaching or exceeding long-term normalcy for the area. Part of the reason that the site produced more runoff after reclamation than before mining is that the premine condition was one of an open, porous soil under woodland, while the postreclamation condition was one of a compacted, bulldozed soil. Sediment concentration results were influenced by failure of the postreclamation erosion control system and by a series of detention reservoirs above the stream monitoring station.

Jan 1, 1983

By F. Fraas

ELECTROSTATIC methods are used to separate and concentrate or purify granular particles derived from ores or various synthetic and agricultural products. Compared with other separation methods that require many technological refinements, the electrostatic attraction of fibers, grass, and seeds to charged surfaces clan be accomplished under the most primitive circumstances, and the early development of this method of beneficiation seemed very promising. Precise application of the method to provide high selectivity, however, is a complex procedure, and interest in this method declined. During this period Mr. O. C. Ralston initiated a Bureau of Mines research program oil electrostatic separation. It is the purpose of thins publication to describe the development of the electrostatic method of particle separation from the early beginning to the present resurgence of interest. Most of the information for this description bas been derived from references, a few of which were not available for thorough review. Much information has been drawn from the investitions of the Bureau. Acknowledgments Mr. O. C. Ralston, former Chief metallurgist of the Bureau of Mines, began the research program on the subject and did research on the mils literature. Both Mr. Ralston and Mr. H. B. Johnson, former president of the Huff Electrostatic Separator Co., furnished patent references. A critical review by Mr. F. D. Lamb, Research director, and Mr. M. J. Spendlove, Supervisory metallurgist, Bureau of Mines, College Park Metallurgy Research Center, lifts been of much value in preparing this report.

Jan 1, 1962

By E. J. Haas, K. A. Rost

"This study sought to identify changes in continuous mining machine (CMM) operators’ risk perception and risk behaviors as a result of adding a proximity detection system (PDS) into their environment. To accomplish this research task, 9 CMM operators from 5 locations were interviewed. Interviews were thematically analyzed for constructs including patterns in risk perception and behavior before and after PDS integration and the process of adapting to the PDS. Operators discussed standing in the red zone less than they did before using the PDS; however, they also discussed other risky decisions they made while learning how to operate their CMM with the PDS technology such as “cheating” the technology and working faster to meet production goals. The process of relearning job tasks with technology and unintended behaviors as a result of that relearning process need to be taken into account when introducing new technology into the mine environment. The study results show an in-depth view of mine workers’ perspectives and how their job tasks and environment could be or are affected when learning how to use new technology that are relevant to companies and mine operators when introducing new technology into the mine environment. INTRODUCTION Established “red zones” can help prevent striking and pinning incidents by providing guidance to continuous mining machine (CMM) operators about where they should stand and not stand while operating a CMM. Although red zones influence operator placement positions, these guidelines are not foolproof safety mechanisms. Depending on the job task and circumstances of the mine environment, a CMM operator may unintentionally or intentionally stand in a red zone. For example, CMM operators may work in close proximity to their CMM for better visual attention cues and the ability to work at a higher rate of production [1-3]. To further enhance protection and prevent collisions between vehicles and mine workers, a proximity detection system (PDS) was developed for the industry. The PDS determines an individual’s position relative to a specific piece of machinery, issues visual and/or audible warnings to the mine worker to change positions, and, if necessary, disables machine motion [4]. The introduction of new technology within other sectors has been identified as a factor that influences work decisions. Specifically, previous research demonstrates that when technology debuts there can be an initial intrinsic risk perceived among users about how the technology will interact with their current environment and behaviors; however, these ambiguities, including the possible risks and benefits, are seldom studied [5]. Some research suggests that the constant presence of technology can disrupt situation awareness and decision-making capabilities by increasing worker responsibilities and worker cognitive demands [6-8]. Further, if workers’ perceived risks both with and without technology are misjudged, unsafe decisions that result in human error and injury may be more likely [9-11]. Although these statements are provided within a broad contextual framework, they support the need to study how technology is perceived among end users in their own environment. Because research about technological impact on worker behaviors has suggested both positive and negative consequences of technology, this issue is worth addressing in the mining industry. Specifically, research has not determined whether CMM operators view their placement choices in the red zone as safe or risky and what effect PDS technology has, if any, on risk perception and subsequent risk behavior."

Jan 1, 2015

By F. Grant

"General *The mining experiences of the coal mining industry in Western Canada have been extremely varied, with the mining companies having to adjust their operations or fail due to the harsh economy of the country in the first part of the century. The bituminous or mountain mines had the railways as main consumers with, at times, optimism that potential steel producers would require metallurgical coal. The prairie and foothills mines mainly provided household fuels, with the fine coal sold to local thermal power plants at discounted prices. In practically all cases fuel competition was very keen, and the less successful mines ceased operations in short-time spans. Knowledge of the parameters that governed the success or failures of the past coal operations should be of value to the present and future mining companies. The initial coal mines were small and were started to supply local demand. These mines had little in the way of capital machinery, engineering, or transportation equipment; therefore the mining methods and mine plans were very simple. The first industrial-sized mines imported most of their management and mining methods from other mining areas, mainly Great Britain. It took time to change the bias of management and mining methods to the requirements of strata characteristics, with rapid closure to those mines that were slow to adapt working methods. The main markets for coal were for household fuel, thermal power plants and railways, with very few other industrial markets developed. The economy of the period was harsh and cyclic and the coal mines were affected more than most industries by these boom and bust periods. It led to the survival of the fittest or the most efficient. Due to the economy, mechanization was introduced to the mines very slowly, with the inability to sell coal fines at a profit being another reason for the delay. Manual labour with hand tools was the main means of production. The work was heavy and arduous, and the pay was based on contract coal tonnage; therefore both men and management paid close attention to details so that nonessential work could be eliminated. Mine openings were dimensioned so that coal could be loaded easily by hand and support requirements were kept to the minimum. Transporting and handling the timber supports required heavy labour; thus the most efficient dimensions were chosen to suit the strata. On the other hand, during the main production seasons the mines tried to make the strata stress work for them so that the pressure was kept on the coal face to keep the coal loose while the strata, a short distance back, was induced to cave to minimize the abutment stresses. This caused mining to be an art, using skills developed by experience with the strata. This led to the development of efficient mine layouts with the openings dimensioned to the strength of the strata and the type of support available. The lack of capital and mechanization, and the manual labour, induced the mines to correlate their service and haulage systems with their mining methods. This caused many innovations that proved very practical."

Jan 1, 1985

By Kul Bhushan

This paper presents the results of lateral load tests on 0.61-m to 1.27-m (24 to 50-inch) diameter drilled and cast-in-place piers in San Diego area residual/formational soils. The test piers were installed and tested in the following soils: Decomposed Granitic Rock (Ktd), Stadium Conglomerate (Tst), and Friars Formation (Tf). Lateral loads of up to 845 KN (190 kip) were applied to the piers in residual granitic soils, and loads up to 1780 KN (400 kip) were applied to the piers in Stadium Conglomerate and Friars Formation. The tests were conducted by jacking against adjacent piers and monitoring the lateral load and lateral deflection at the ground line. Test results indicate that ultimate lateral pile capacities of up to 1800 KN (400 kip) can be obtained for 0.61 m (24-inch) drilled piers with penetration of 3 to 6 m (10 to 20 ft) in the residual/formational soils tested. Lateral load analyses using p-y curves for very dense sand significantly overestimate the observed lateral deflections. For lateral load analyses using dense sand p-y curves, p-multipliers that increase the lateral soil stiffness (p-y curves) by 2 to 8 times are required to match the load-deflection behavior measured in the test piles. When applied to the dense sand p-y curves, the p-multipliers provide a more accurate prediction of load-deflection behavior in the residual/formational soils, and can result in shorter required pier penetration and significant savings in foundation cost.

Jan 1, 2002

By Justin Lukens, Di Stasim Jeffrey, Frank Di Salvo

Columbia University’s Manhattanville Campus expansion includes the construction of two new business school buildings. The new buildings require development of an entire city block bound by 12th Avenue, W 131st Street, W 130th Street and Broadway in Upper Manhattan. A support of excavation (SOE) package was first released, followed by a foundation package. The SOE package consisted of approximately 100 soldier piles and 280 anchors, up to 215’ long, to support a cut anywhere from 30’- 50’ below street level. The foundation package alone included approximately 1600 drilled micropiles. Given the breadth of the work scope, Hayward Baker Inc and Moretrench joint ventured on these two projects to bring sufficient knowledge and work resources to complete the work in an efficient and timely manner. This included working with the Owner/Engineer to propose different means and methods for construction to significantly reduce the schedule while meeting the design intent, such as large diameter (36” diameter) augercast piles in place of conventionally drilled soldier piles and large hollow-bar micropiles (103/51 bars) in lieu of pressure-grouted micropiles. The anchors, ranging from 3 to 22 strands, were used for earth retention through both soldier pile and lagging walls and existing slurry walls. These anchors were complicated based not only on their size and length, but also the need to drill some of them under the historic Studebaker building. The overall magnitude of the project with considerations to resource management and material lead times will be addressed, highlighting critical strengths provided by the Contractor to ensure project success. The scope of work discussed in this paper was executed under two separate competitive bid contracts. The first contract included the support of excavation work and the second contract included the foundation package. The support of excavation comprised of drilled soldier piles (performed by Case Foundation as a subcontractor to the JV), driven soldier piles, driven sheet piles, hollow bar tiebacks, multi-strand tieback anchors and micropile soldier piles. The foundation package consisted of drilled micropiles. Due to the large scope of work and critical schedule requirements of the project, the JV had to think outside the box and present value engineered alternates to expedite installation durations.

Jan 1, 2019

By A. Dubé

Introduction It is common experience that on re-heating a fully martensitic steel below the Ac, point, a softer and tougher structure is formed as the tempering temperature is raised. The mechanism of tempering of plain carbon and low-alloy steels has been the subject of many investigations. In a very comprehensive study, Cohen and associates have recently established three different tempering stages, the last of which reaches completion at about 700°F., with heating rates of 5°F. per minute. This latter stage has been established ta be the carbide-forming stage, so that the steel consists of a mixture of ferrite and carbide, which are the metastable equilibrium phases. Any subsequent changes which take place at higher temperatures below the Ac, point in the absence of graphitization or carbide lattice conversion normally consist of agglomeration of the carbide particles. This naturally results in the softening of the steel. However, in many cases the Ac, point, as determined by dilatometry, thermal analysis, etc., only gives a rough estimate of the temperature where the reaction, ferrite plus carbides to austenite, is initiated. This appears to be especially true in the case of alloy steels in which three phases can co-exist in certain temperature ranges. Bain has given data on the three-phase equilibrium in both manganese and nickel steels. In these steels, the formation of austenite at temperatures just above the AeIL apparently involves the diffusion of the alloying elements to the first pools of austenite, thereby making the process very sluggish. As a consequence, the critical Ac points determined by ordinary methods at normal rates of heating can be quite distant from the true equilibrium Ae temperatures.

Jan 1, 1946

By Nick Rose, Mathieu Veillette, Matthew King

"The Teck Highland Valley copper (THVC) mine is located approximately 55 km (34 miles) southwest of Kamloops and approximately 20 km (12 miles) west of Logan Lake, BC, Canada (Fig. 1). Mining at THVC is conducted at three openpit operations comprised of Valley, Lornex and Highmont with a total annual output on the order of 300 kt (330,000 st) copper concentrate and 5 kt (5,500 st) of molybdenum concentrate. The Phase 8 pushback in the Valley Pit (Fig. 2) was mined from 2011 to 2016. Successful slope steepening occurred in the later stage of the pushback with the implementation of presplit blasting in 2015 and 2016.This article summarizes the investigation and design approach including: structural analysis, kinematic assessments of bench breakback potential, development of discrete fracture networks (DFNs) to characterize discontinuity fabric, rockfall modelling, 2D anisotropic limit equilibrium and 2D distinct element modelling, assessment of potential kinematic failure modes affecting double benches with 3D distinct element modelling and improved blasting techniques using e-dets. THVC is currently undertaking a mine life expansion involving the pushback of the west wall of the Valley Pit above Phase 8 to extend the mine life to 2029. Engineering geologyThe east wall slope in the Valley Pit is comprised of a 350-m (1,148-ft) thick sequence of glacial valley sediments that occur along the Highland Valley (Fig. 2), exposing an overburden slope up to about 225-m (740-ft) high below the crest of the ultimate east wall. The glacial overburden units consist of pro-glacial outwash and glaciofluvial deposits, glacial outwash sands and gravels interbedded with till and alluvial fans consisting of cross-bedded sands and sandy-gravels. Lacustrine sediments occur within the mid to lower portion of the glacial sequence and contain intervals of low-shear-strength clays and silts. Two large (1.3 and 7 Mt or 1.4 and 7.7 million st) waste rock buttresses were required to maintain slope stability using slot-cut and fill mining methods, as described in Fortin et al. (2011).The Valley porphyry deposit occurs in the central portion of the late Upper Triassic Guichon Creek Batholith, which intrudes assemblages of the Permian Cache Creek and Upper Triassic Nicola groups. The Valley deposit occurs in an area of intense fracturing near the intersection of the northerly trending Lornex Fault and the northwest to westerly trending Highland Valley Fault."

Apr 1, 2019

A maximum acceptable level of 2 mg/m3 of respirable coal mine dust in active mine workings was established, effective January 1, 1973, under the Federal Coal Mine Health and Safety Act of 1969. It is generally agreed that, as a result, coal mines in the United States are significantly less dusty than they were a decade ago. For example, operators of underground mining machines were exposed to between 3.9 and 6.5 mg/m3 of respirable coal mine dust during 1968-69; now they are exposed to between 1.3 and 1.8 mg/m3. Also, the incidence of underground sections cited for exceeding acceptable levels of respirable coal mine dust decreased during 1976-78, and the vast majority of all working sections are now in compliance. This improvement is very substantial by world standards. It must be regarded as a creditable accomplishment by the coal mine operators, federal agencies, and mine workers involved. Most of the improvement has been brought about by the use of existing technology to control, suppress, and collect respirable coal mine dust. Research and development by the Bureau of Mines has contributed significantly to the accomplishment by improving the methods for sampling, control, suppression, and collection.

Jan 1, 1980

By Robert L. Lagace

[Suuple Iheorctrccil models are I'M lllolalcd to cltaraclerl/c medium frequency (MF) radio vase pi opaiation in undcrgiounli room arid pillar coal mines fur the purpose of predleiln the most lavolable operating fIegtucncics,md nr,ixunum communic;IIIoil ranges for pottahIe rldu)s with I top antennas. I or conductul IrCC areas, at hree layer propaeaIion IltodcI wit II a Iiallsmissloil IIIIi- lhlllllIIal'u11 lot the plupa!edti ii unlstallt Iris been dcvcloped ;md verified experimentally. 1 lie mode u1 propaCaUetl lakes Ills form of i parallel plane (0,t)) TIM lransnussu)nhne 1% PC of mode with the electric held vertical and the magnetic held hoti/cntal t itliin a planar coal scam in which the tunnels Can he ignored and which 1s hounded above and below hp richer conductivity rock. 1lie model lilt the data best river the 200 io 1000 kH/ frequency hand and exhibits a rc;;lon of optlnrul1l Pelffelntance, with respect Io maxnluiulg radio Communication range, between 300 and 100 klf/. Maximum cunununlcatrorl ranges are sliongls dependent oil the sigiial alleilliatroil sale, ant) Illelclulc on the electrical conductivltles of the coal seam and surrounding ruck. These ranges v;ny tutu about ,,5 Io 100 nleleis Ill a high Iuss scam such as the Ilelllit No. fl to about .100 to 400 meters in a low loss seam such as the Pittsburgh foil portable intrinsically safe radios. The ieslllls die haled on the comparison oftheorc' and experiment for eleven n n. ill sesen coal seams. V OT ate is dice: a conductor such as a power Cable, is present a model has been developed for the coupling of loop antennas to a low loss Coaxial TEM ti;u?smisslon line mode in which the cable acts as the inner conducl,lr and the rock above and below acts as the outer conductor. The electuc and md' nctic Itelds for till` (node are apprlixitllatcly transverse to the cahlC and fall oil expontially with distance in the transverse plane. The principle of reciprocity is used to simplify the analysis. More expelitnental data arc needed to help resolve discrepancies between the theory and the limited data available to date.]

Jan 1, 1980