Search Documents

By N. Melnyk, H W. Habgood

The conventional low temperature process for extracting' helium from natural gas involves liquefying the whole gas stream in order to remove the relatively small fraction of helium. A process based on the selective diffusion of helium through a semi-permeable barrier is, in principle, more economical and flexible, particularly for the treatment of small re-serves and low concentrations. The well-known permeability of glass to helium offers the possibility of such a diffusion process and McAfee of the Bell telephone Laboratories showed in 1958 that practical separations could be achieved by passing natural gas over bundles of fine capillary glass tubing. Developmental studies have been carried out involving larger units and more extended field tests than those of McAfee. Fine capillary tubing of Pyrex glass 0.0035 in. diameter was prepared by drawing ordinary 6 mm. laboratory tubing in a furnace. Extraction units were pre-pared containing about 10,000 such tubes, 4 ft. long and cemented inside

Jan 1, 1961

By Robert M. Strong

The following report is a summary of the commercial results which 'Were obtained from 2,000 tests conducted by the technologic branch of the United States Geological Survey at St. Louis, Mo., and Norfolk, Va., in 1907 and 1908, under the technical supervision of R. H. Fernald, engineer in charge of the producer-gas section. The tests dealt primarily with gasoline, forming part of the investigation of mineral fuels provided for by acts of Congress. To determine the relative economy and efficiency of gasoline it was compared with denatured alcohol. The tests, many of which were undertaken in connection with work for the Navy Department, supplemented, to a certain extent, the work of previous investigations, but only so far as was necessary to emphasize some of the more important points and to lead up to the defining of conditions required for the economical use of gasoline and alcohol. In order to determine and eliminate the affecting engine conditions as far as possible, the investigation was commenced by making comparative gasoline and alcohol tests on the same engines. These tests were repeated on other engines of approxiElately the same size and speed, having different degrees of comFression, different methods of governing, and different carburetors. The final report will include much material that may be of use in engine design, but that side of the investigation was not pursued any further than was necessary to obtain the best possible results, for alcohol and for gasoline with the engines at hand, and to prove that the minimum fu·el-consumption rate for each could be obtained in approximately the same manner. The effects of engine and of operating conditions both have a bearing on the commercial deductions but will be discussed only in a general way at this time.

Jan 1, 1911

By CHARLES L. WRIGHT

Coals may be divided into six classes-anthracite, semi anthracite, semibituminous, bituminous, subbituminous, and lignite. The first three cla~ can be distinguished by dHferences of composition, particularly the proportions of fixed carbon and the ratios of the fixed carbon to the volatile matter in the cools. The last three classes can be distinguished by di:fferences in physical character, chiefly in color and in manner of weathering. Lignite is brown, not black, and has generally a woody look, but it weathers in much the same way as subbituminous coals. On exposure to the air lignite slacks or crumbles. The lumps check and fall into small irregular pieces that exhibit a decided tendency to separate into extremely thin plates. Hence lignite deteriorates greatly during storage or long transportation. The most characteristic feature of the composition of lignite is a large percentage of moisture. '!his high moisture content reduces the fuel value of freshly mined lignite, and the partial evaporation of moisture, on expooure, causes th6 fuel to check and fall to pieces. Consequently, attempts to increase the efficiency of lignite as a fuel involve reducing its percentage of moisture and increasing its ability to endure storage and transportation. Both these results are accomplished by briquetting.

Jan 1, 1911

By N Lefebvre, M Jakeman, R Aseervatham

Semi-arid regions suffer from two afflictions; evaporation may exceed precipitation by multiples of two or more and variations in precipitation can be both extreme and difficult to predict. Many Australian mines are situated in semi-arid areas where communities are reliant upon locally sourced water or special purpose infrastructure is built as part of the mine construction. As the question of climate change looms, issues related to future water supply and sustainable water management become increasingly important. Across Australia several mining operations co-exist in a single surface water and/or groundwater catchment area. The management of water on a mine by mine or a community by community basis is illogical and must be reconsidered based on a single water catchment and a whole-of-community basis. Mine water should be considered on a full life cycle basis where the quality is assessed for specific mine site applications. This paper addresses technical challenges that include surface water and groundwater supply in semi-arid regions, operational water in the mining industry, beneficial uses of water, water economics and demand management. In much the same way as emissions trading evolved into a multi-stakeholder forum, mining regions offer scope for innovative thinking in water supply and reuse. In addition, this paper considers a number of initiatives taken by Australian mining companies that are entering a prefeasibility stage and contrasts these initiatives against the established success within a South African mining region. The challenges and potential solutions to this initiative are presented for future consideration.

Jan 1, 2006

By Valeria Collini, Antonello Mestroni, Enrico Plazzogna

The Danieli Group is deeply involved in the technological improvements stimulated by Industry 4.0 concepts widely applied to the metals industry and process automation. The so-called "Intelligent Mill" is the natural evolution of the company’s consolidated know-how and undisputed leadership in the fields of mini-mill and turnkey plants. Complete and structured data collection is the basis for real-time analysis and process optimization in terms of quality, efficiency and easy maintenance. A centralized repository of information is possible thanks to the strong interconnection between process control system architecture and intelligent sensors, together with dedicated software tools leading to an intuitive approach to data analytics.

Oct 1, 2019

By F. M. Boler

The U.S. Bureau of Mines conducts research at the Galena Mine, Wallace, ID, with the aim of mitigating the effects of rock bursting. Destress blasting is commonly used as a stress control technique at the mine. A digital seismic array and an array of borehole pressure cells (BPC's) had been installed near the site of a stope undergoing mining and periodic de stressing. The instrumentation was being monitored at the time of a destress blast of the 46-99 stope. No significant seismic events occurred coincident with the destress. However, the destress was followed by a 2 ½ -week period of increased seismic activity, including two damaging events on February 7, 1990, at 034500 (hour, minute, and second) and 122020 Pacific standard time. BPC measurements indicated coseismic ground pressure changes on the order of 200 to 300 kPa associated with the damaging events. Fault plane solutions and dislocation models established that stress changes induced by the event at 034500 may have been significant in promoting the occurrence of the event at 122020. Theoretical investigations suggest that applying knowledge of the existing stress field, an understanding of rock burst mechanics, and fracture mechanics principles can improve destress effectiveness.

Jan 1, 2010

By Martha Gross, Amanda Wachenfeld, Brian Keaney, Jean-Michel Charpentier, Frank Perrone

The Hampton Roads Bridge-Tunnel (HRBT) Expansion widens the existing four-lane bridgetunnel corridor to eight lanes through construction of two parallel tunnels, interstate widening, and bridge expansions. As part of the design-build contract, a supplemental geotechnical investigation was completed to support the design. The investigation for the subaqueous tunnel segment consisted of over 48,400 linear feet of drilling and 7,100 laboratory tests. This paper discusses the challenges of planning and executing a large-scale geotechnical investigation for underground works in a marine environment and the use of big data for effectively managing, interpreting, and transmitting data to the design-builder consistently throughout the investigation.

Jun 23, 2024

By W. D. Bullock

The King-Beaver mine of Asbestos Corporation Limited operates an open pit in the city of Thetford Mines, Quebec. The approximate loca-tion of the open pit is at Latitude 46° 02' North and Longitude 71° 20' West. The general topography is 1020 feet above sea level. Thirty-six percent of the company's scheduled asbestos ore production, for the Thetford Mines area, comes from the King-Beaver pit. The pit operates 24 hours a day, six days a week. Normal production is 10,500 tons of ore per day at a waste to ore ratio of 2 to 1. The remaining ore requirements are mined from the King-Beaver underground mine and the British-Canadian mine.

Jan 1, 1980

By Hillary W. St. Clair

This report describes an experimental method for determining parameters for the rate of reaction of CO2 with solid carbon. The method involves the simulation of a flow reactor by a mathematical model based on a hypothetical multistage reactor which permits calculation of the analyses of effluent gas and carbon consumed as functions of the flow rate and duration of the reaction. The method is applied to experimental data on the reaction of coke with CO2 in fluidized-bed and fixed-bed flow reactors. A method is described whereby two parameters may be determined simultaneously. The method involves a reiterative procedure that finds the values of the parameters that minimize the sum of squares of deviation between calculated and observed analyses of the effluent gas.

Jan 1, 1971

By J. Dean Warner

In 1984 and 1985, as part of its critical and strategic minerals studies, the Bureau of Mines investigated lode and placer tin occurrences near Rocky Mountain (Lime Peak), in east-central Alaska. The lode occurrences consist of mineralogically complex, generally fault-controlled veins, and contain an average of approximately 0.05 pct Sn, as cassiterite. Beneficiation testing of two bulk samples of the vein material produced concentrates containing 65 and 59 pct of the total tin values at grades of 0.35 and 13.9 pct, respectively. Although as much as 30 million short tons (MMst) of mineralized rock containing up to 20 MMlb Sn may be present, the grade of these occurrences is too low to be considered economic at this time. Trace amounts of cassiterite were also identified in surface samples of glacial out-wash gravels collected along North Fork Preacher Creek, which partially drains the area of tin lode deposits near Lime Peak. Low tin grades in the samples do not account for the former erosion of a large volume of lode tin mineralization from near Lime Peak; higher tin grades may be present in gravels closer to bedrock.

Jan 1, 1988

By Ali Kahriman, D. Adiguzel, R. Ulger, U. Akkaya

The environmental problems arising from ground vibration has been faced and discussed frequently in various industries such as quarry, mining, civil works, shaft, tunneling, pipe line and dam construction etc. where the blasting operations are unavoidable. This paper presents the results of ground vibration analysis induced by blasting during the construction of the Istanbul Kadiköy-Kartal metro tunnel. Different rock formations in this tunnel route which is 21.6 km in length were encountered during the excavation process by blasting. As a first stage, Hoek’s Geological Strength Index (GSI) values of rock units were determined by using inverse distance weighting method. The GSI values which were obtained from boring data were used when evaluate the data. GSI values were estimated by inverse distance method (figure 3) along with the tunnel route. Afterwards, ground vibration parameters induced by 21 shots which were made in different locations was monitored and passing routes of vibration waves determined. Weighted averages of GSI values were calculated according to distance of the regions where vibration waves passed. Multi regression analyze were made with using frequency, charge per delay, GSI and the distance between the shot point and monitor station. The main goal of this study is to investigate the relationship between ground vibration frequency induced by blasting and GSI.

Jan 1, 2011

By Jos. R. Guiteras

This paper has been written to describe briefly the mining and milling of gold and silver ores in the Black Canyon and neighboring mining districts in Yavapai County, Ariz. The description of present operations is the result of a 10-day visit to the region by the writer in March 1936. Acknowledgments The author is indebted to earlier writers on the geology and mining in this regions and to the mine managers and their staffs, whose courteous cooperation has made possible the assembling' of material for this paper. Individual acknowledgments are made in the text.

Jan 1, 1936

By M Logsdon, B Johnson, M Fordham

The underground Neves Corvo copper-tin mine in southern Portugal currently disposes of its tailings in a ætraditionalÆ wet tailings impoundment. With the development of new technologies for preparation and transport of thickened tailings or paste, alternative tailings disposal options have become available that provide a more sustainable water management system and a higher degree of environmental protection. In addition, growing European resistance towards subaqueous disposal may well result in mandatory use of dry disposal methods in the near future. Twenty-four tailings disposal alternatives were evaluated through a cost-effective and easily-implementable bench-scale geochemical screening program conducted at site. Since the tailings are pyrite-rich and highly acid generating, particular emphasis was placed on monitoring likely indicators of sulfide oxidation under the various simulated disposal scenarios. Dependent parameters investigated as part of the program included moisture content, use of alkaline additives (lime, cement), use of a bactericide, and agitation. Response parameters included paste pH, specific conductance, and temperature as indicators of oxidation. The testing was carried out for 30 weeks. Results indicate that a number of relationships between the geochemical stability of the samples (ie sulfide oxidation) and sample characteristics can be readily identified. Based on the results of the screening program, a limited number of tailings mixtures have been selected for further long-term testing in field weathering cells to aid in the identification of the optimal mix design for future tailings disposal at the Neves Corvo Mine. This type of testing provides an inexpensive and reliable methodology for semi-quantitative comparison between tailings disposal alternatives, in particular at locations where more rigorous evaluation through long-term, fully replicated testing is not immediately feasible.

Jan 1, 2003

By F. Keller

SOME PHRASEMAKER has aptly said that nature made aluminum light but research made it strong. Research has been a vital element in the past progress of the aluminum industry and its future growth likewise depends upon the application of the results of research. The role of aluminum products in World War II is well known and this metal will certainly be increasingly important in the postwar world. Some of the principal developments in the war years were in the field of high-strength aluminum alloys. New and stronger alloys were developed which enabled designers to get increased speed and performance in our fighter planes and bombers. The aircraft industry will continue to use these new materials for peacetime passenger and cargo airplanes. High-strength alloys will also find structural applications in trucks, buses, trains, ships, and bridges.

Jan 1, 1946

By Kenneth K. Landes

So far my consulting in industrial minerals has been confined principally to carbonate rocks,-salt, coking coal, and glass sand. Much of this work has been for companies either too small for a full-time geological staff or unaware of the value of employing one or more qualified geologists permanently. It gave me considerable personal satisfaction to see several of the latter companies employ one or two full-time geologists after the completion of a consulting contract with them. One possible reason why some companies lack the wisdom to hire geologists is that they are dominated by engineers who still subscribe to the old idea that engineers are self-sufficient in all fields. They could have learned this from their professors. I once knew a Dean of Engineering who got purple in the face when a faculty committee was discussing the financing of a broad gauged engineering project and suggestions were made that assistance be obtained from the Schools of Business and Law and from some of the science departments tie pounded the table and shouted "Engineers are trained to handle all this!" In teaching engineering geology some years ago I used to tell the class repeatedly that the course would not make them geologists, that the purpose was to teach them

Jan 1, 1972

By M. Fan, H. E. Wyslouzil, J. Kohmeunch

Eriez HydroFloat(TM) separators and Canadian Process Technologies (CPT) flotation columns have been developed to overcome the limitations of traditional flotation cells in recovering coarse and fine particles, respectively. The flotation column can effectively separate 30-5 µm phosphate. Several industrial-scale HydroFloat separators have been installed in phosphate and potash beneficiation plants. Industrial-scale ultra-coarse (+850 µm) phosphate separation results suggest that a more-than 40% BonePhosphate- of-Lime (BPL) recovery increase and a 37% collector consumption reduction can be achieved. The paper describes the applications of Eriez HydroFloat separators to coarse particle separation and the CPT flotation column to fine/ultrafine particle flotation.

Jan 1, 2009

By N. Morrison, I. Holl, R. Welyhorsky, A. Hempstock

ABSTRACT: The Victor diamond mine is located in the James Bay lowlands, 90 km west of the First Nations village of Attawapiskat. The project was the first of its kind in northern Ontario. The process plant was designed to produce a 95 to 98% by weight diamond concentrate through three stages of comminution, dense medium separation, and proprietary X-ray technology for final recovery. The plant was commissioned over a period of six months, commencing prior to substantial completion of construction. Through effective planning of the commissioning phase, the Victor mine start-up was safely completed nine months ahead of schedule.

Jan 1, 2011

By John P. Gooch

The solubility of 1,1,2,2-tetrabromoethane (TBE) in water was determined from 1.0° to 97.0° C. The solubility (S) of TBE in grams of solute per 100 grams water was correlated with [S = 1,920.55 [exp (40292L7 11, T2 10 T 737.577 + 9.923962 ] where T is in degrees Kelvin. A thermodynamic analysis conducted on a system consisting of a TBE phase and a water phase in equilibrium with a vapor phase led to the calculation of the activity coefficient, vapor-liquid equilibrium distribution coefficient, relative volatility, and heat of mixing for saturated solutions of TBE in water. Data required for these calculations were the solubility of TBE in water and the vapor pressures of TBE and water as a function of temperature.

Jan 1, 1972

By J. R. Nettle

A method has been developed in the laboratory for successfully electro-refining titanium metal. Refining is accomplished in e fused-salt electrolyte using offgrade metal as the anode and collecting the purified metal at the cathode. The characteristics and requirements of the various alkali chlorides tested as electrolytes are discussed in relation to relative ease of purification and serviceability. The various types of cells designed and tested for electrorefining are illustrated and their method of operation discussed. The individual advantage of each cell and the purpose for which it was designed are reviewed. The magnitude of the cathode current density was found to depend largely upon the quantity of soluble titanium chloride in the electrolyte. The physical condition of the anode also greatly affected the cathode current density.

Jan 1, 1957

By Michael Wortley

Metso?s Process Technology and Innovation group is a world leader in mineral processing consulting. A significant amount of this consulting work involves process integration and optimization (PIO) studies, which include investigating the effects of drill-and-blast design and implementation on downstream processing. Critical to these studies is the ability to track specific ore into, and through, the plant. To increase the accuracy of this ore tracking, Metso Process Technology and Innovation (PTI) developed a system to track ore using a radio frequency identification (RFID) transponders technology designed to allow tracking of ore from its source through blasting, run-of-mine (ROM) pads, crushers, intermediate stockpiles and, finally, into the concentrator. The system is called SmartTag. Since its commercialization in 2007, SmartTag has been used in the majority of PTI?s consulting projects, and several permanent systems have been installed worldwide.

Jan 1, 2012