Search Documents

By Robert B. Fulton

Staurolite, an iron aluminum silicate mineral, is used industrially as a high value-in-use sandblasting agent, as a premium-grade foundry sand, and as the source of aluminum in portland cement manufacture in areas where the aluminum constituent is not economically available from shale or argillaceous limestone. Staurolite is produced by E. I. duPont de Nemours and Company as a coproduct of titanium mineral production in Florida, where it was first recovered on a commercial scale in 1952 from the Pleistocene sand deposit known as Trail Ridge. At this deposit it comprises about one-fifth of the heavy mineral suite, the principal other heavy minerals being ilmenite, leucoxene, rutile, zircon, kyanite, sillimanite, and tourmaline. Staurolite and other nonconductive silicate heavy minerals are separated from the conductive titanium minerals on high-tension electrostatic separators. The silicates are then separated from one another magnetically, the staurolite being relatively magnetic. In the total process, 200 t of raw sand yield 7 t of heavy mineral concentrate from which about 1 t of staurolite is recovered. The staurolite concentrates have the characteristics given in Table 1. Staurolite concentrates are sold in three grades having the size distribution of subrounded grains shown in Table 2. All three grades are used in sandblasting for cleaning metal, for paint removal, and for cleaning masonry buildings. Staurolite compares favorably with lower priced abrasives, such as boiler slags and silica sand, in applications where the abrasive is used only once and is not recovered and recycled. Because it is hard, fine, clean, and dense it can reduce blasting time, and less material is required to clean a specific area. Compared to higher priced abrasives such as aluminum oxide and garnet, which are recycled, staurolite costs significantly less per kilogram and cleans at equal or faster rates. Its breakdown factor, which is a measure of recycling performance, is intermediate between those for aluminum oxide and garnet. [ ] [Tables 3 and 4] show the blast cleaning performance of the three staurolite grades compared to other abrasives. [Table 5] compares the longevity of premium priced abrasives during recycling. [Table 6] shows a cost comparison between silica sand and staurolite. Fringe benefits claimed for staurolite's use as an abrasive are: 1. Good flow properties and freedom from the lumps or slivers found in silica sand or boiler slag abrasives. 2. Low dusting affords good visibility, permits faster working, and reduces cleanup problems. 3. Heated storage is not required during freezing conditions, because the mineral is nonhygroscopic.

Jan 1, 1994

By F. S. Crawford

Mining companies are usually held responsible for accidents occurring to the public around their operations . Safeguards are provided by progressive mining companies to prevent the public from getting into danger from wandering unattended about the properties . At abandoned operations , where little or no supervision can be maintained , persons are often injured through the negligence of the operator in leaving the property in unsafe condition . After a mine is abandoned or a lease is given up by a mining company , the responsibility for the safety of the property rests sometimes with the State to which the property ownership reverts or with the owner of the land ; either is usually quite unwilling to spend any money to remedy unsafe conditions due to the carelessness of the mining company . The land owner or the State , or both , should see that the work of leaving safe conditions behind is done by the operator before he abandons the mine or gives up the lease . Some of the worst hazards to the public at abandoned mines are from old test pits , abandoned shafts or tunnels , open pits , caved ground , and bodies of water in abandoned open pits . Hazards exist from some of these sources during the active operation of a mining property as well . In the early stages of mining operations test shafts are often sunk from 50 to 100 feet deep through the more or less loose material overlying bed rock . When these shafts are left unprotected , they are a serious danger for many years to come . In the course of time they become largely concealed by brush and grass , and thus are a deadfall to anyone who might happen to step into them . This condition will hold true for any part of the country, but to a much less degree where it is not necessary to sink through a great amount of cover . Many progressive operating companies have adopted the practice of filling in test pits after securing the information desired . Some nonresident landowners and exploration companies , however , have left such pits open , and it is extremely difficult for the mine inspector to get into communication with the owner . Frequently operating companies voluntarily fill test pits on adjacent property not

Jul 1, 1930

By Minjun Tang, Jianfeng Zhou, Feng Chen, Linjiang Qing, Xiaolei Song, Yufeng Guo, Tao Jiang

"Reduction swellability index (Rsn and low temperature reduction disintegration index (RDI) of vanadium-titanium magnetite oxidized pellets are harmful to the processing of ironmaking, for example, causing serious gas permeability, decreased yield, higher coke ratio and more furnace dust. Thus, the improvements of RSI and RDI of vanadium-titanium magnetite oxidized pellets were investigated in this paper, including the pretreatment of raw material, additives of dolomite or boric acid, pellets treated in chloride solution and so on. The results showed that damp milling as pretreatment and boric acid added in pelletizing were conducive to the RSI which decreased 5% and 7% respectively, while they were not efficient enough in improving RDI. Dolomite was efficient in improving RSI, but had negative effect on RDI. There was no evidence to show that RSI and RDI would be improved when pellets were treated in chloride solution. Pursuing this further, the mechanism of those improvements were investigated.IntroductionIn the world, vanadium-titanium magnetite utilization is investigated around how to recover iron, titanium, vanadium, and divided into blast-furnace method and non-blast-furnace method according to respective characteristics. Blast furnace method [1, 2] can recover iron and vanadium effectively, but Ti02 cannot be recycled. Non-blast-furnace methods include rotary kiln-electric furnace method, pre-reduction electric furnace method, reduction- grinding method and sodium vanadium-rotary kiln-electric furnace method and so on. [3-7]Comparing to the Non-blast-furnace method, the method of blast furnace smelting has been put into industrial applications. And it has the following advantages: First of all, effective recycling iron and vanadium; Second, technical problems of high titanium slag in blast furnace smelting; Third, it has mature technology in blast furnace smelting."

Jan 1, 2013

By O. F. Walker, W. C. Hahn, V. A. Johnson, J. D. Wood

The diffusion coefficients of zinc in single-crystal zinc and carbon in single-crystal and poly crystalline nickel were measured by means of radioactive tracer techniques both with and without the application of ultrasonic vibrations under conditions such that the temperature of the sample was closely controlled. The results of this investigation indicate no enhancement of diffusion in any of the samples. It is suggested that previously reported enhancement may have been due either solely to temperature increases caused by ultrasonic vibrations or in combination with changes in the boundary conditions. A number of observations have been reported in the literature in which it has been implied or inferred that the application of ultrasonics enhances diffusion (see, for example, Refs. 1-5). The present study was undertaken in an attempt to observe this effect under carefully controlled conditions, particularly with regard to measurement and control of the temperature of the sample. Two different types of systems were studied; these were the self-diffusion of zinc and the diffusion of carbon in nickel. EXPERIMENTAL For diffusion with ultrasonic energy applied, the samples were included as part of a resonant ultrasonic system operating at 58.5 kcps. The ultrasonic generators used were rated at 100 and 250 w and could be tuned over a frequency from 10 to 100 kc. A PZT (lead titanate/lead zirconate) ceramic transducer provided the driving vibration. This system requires no metallurgical joining of the specimen to the acoustical transmission line since the ultrasonic driver and the follow-up section clamp the specimen in position by means of a constant pressure of 50 lb developed by an air cylinder. The ultrasonic driver and follow-up section, both made of titanium, were 4 in. in length from clamping point to the end in contact with the specimen. Using the relationship given by Mason,6 A = V/f, the resonant wavelength, A, in titanium is calculated to be 3.3 in. at a frequency, f, of 58.5 kc, taking the velocity of sound in titanium, V, as 1.95 X 105 in. per sec. The 4-in. driver and follow-up section, therefore, are each 4.0/3.3 =1.21 times the resonant wavelength. Clamping pressure must be applied at stress nodes of the transmission line in order to preserve resonance. Therefore, a specimen length of 0.58 times the wavelength in the specimen was required to place the clamping pressure application points at stress nodes exactly three wavelengths apart. A stress antinode was contained in the center 3 in. of the specimen. A small PZT ceramic disc attached to the follow-up section provided an output voltage proportional to the intensity of the standing wave. This output voltage was monitored on an oscilloscope and the ultrasonic system was tuned to resonance by varying the frequency until the output signal was a maximum amplitude. The amplitude of the output signal was maintained constant throughout the diffusion anneal. A split cylindrical stainless-steel chamber, which was purged with argon prior to and during the runs, was placed around the specimen. The chamber in turn was surrounded by a movable furnace whose temperature could be controlled to 7C. Heat exchangers were used to cool the driver, follow-up section, and ultrasonic transducer. Great care was taken to obtain the true specimen temperature in all cases. Several different methods were tried; the most successful was that in which the thermocouple was held in contact with the midlength of the specimen by means of an asbestos insulating pad and wire straps. In the case of zinc, single-crystal specimens of 99.999 pct purity were used. The samples were 0.25 by 0.25 in. square and of the proper length for resonance, that is 1.1 in. long with the c axis parallel to the long dimension of the specimen for the case of diffusion perpendicular to the c axis and ultrasonic motion parallel to the c axis, and 1.9 in. long with the c axis perpendicular to the long dimension of the specimen for the case of diffusion parallel to the c axis and ultrasonic motion perpendicular to the c axis. In each case, one of the rectangular faces was electroplated with a thin film of zinc containing Zn The constant pressure used to clamp the specimen in place in the ultrasonic system caused some deformation in some of the samples. For these samples the deformation was concentrated in either end of the specimen; thus, for all samples (both zinc and nickel) the center in. was cut from the specimen after the diffusion anneal to be used for sectioning and counting. The nickel single-crystal samples, of 99.999 pct purity, were used in the form of rods 0.25 by 0.187 by 2.07 in. long with the (100) direction parallel to the rod axis. The polycrystalline nickel samples of 99.97 pct purity had an average grain diameter of 0.007 in. and were used in the form of rods 0.25 by 0.125 by 1.87 in. long. The direction of ultrasonic motion was parallel to (100) direction (bar axis) for the single-cqstal samples and parallel to the bar axis for the polycrystalline specimens. A thin film of c14 suspended in methanol was applied to the diffusing face of the specimen. Two specimens were butted together lengthwise for each diffusion anneal to minimize oxidation. After diffusion, a precision lapping device similar to the one described by Goldstein7 and a radiation detector were used to obtain a plot of specific activity vs penetration distance for each specimen. (A scintil-

Jan 1, 1969

By R. F. Krueger

Results are presented from tests of dynamic fluid-loss rates to cores from clay-gel water-base drilling fluids containing different commercial fluid-loss control agents (CMC, polyacrylate or smt,ch), organic viscosity reducers (quebracho and complex metal lignosulfonate) and oil at several different levels of concentration. In the dynamic system the most effective individual additives to the clay-gel drilling fluid, based on cost-equalized concentrutiom, were found to be starch and the viscosity reducers. These results do not conform with the rankings determined by API fluid-loss rests, which indicate CMC, polyacrylate and starch to be the most effective and comparable. Generally, minimum dynamic fluid-losr rates were attained at cost-equalized concentrations of additive (including thinner) of about $1.00/ bbl, or less. For chernically treated clay-gel drilling fluids, both the standard and the high-pressure API filter-loss tests were found to he inaccurate indicators of trends in dynamic fluid-loss rates under the test conditions used, particulurly for drilling muds containing viscosity reducers. From a practical field viewpoint, restrictions on the applicability of the API fluid-loss test are such that it is open to question whether or not results of this test can be used routinely with confidence as an indicator of control of down-hole fluid loss under field treating conditions. INTRODUCTION The petroleum industry spends large sums of money during drilling operations to control the fluid-loss properties of drilling fluids based on the standard API filter-loss test,' which is a static filtration system. Laboratory studies' ' of dynamic filtration have shown that in a given time period filtrate loss from a circulating mud stream is greater than from a static system and that it is a function of linear mud velocity, pressure and the properties of the drilling fluid. Ferguson and Klotz' and Horner, et al," observed that (I) the dynamic fluid-loss rates for the drilling fluids used were not related to the extrapolated API filter loss and (2) the drilling fluids with the lowest API filter losses did not have the lowest dynamic fluid-loss rates. However, there has been no published information on the relative effects on dynamic fluid-loss rate as a given drilling fluid is treated with increasing amounts of chemical additive to reduce the API filter loss. Such information is economically important because drilling-fluid costs rise rapidly as chemical requirements increase. This paper presents the results of a study of dynamic filtratioi rates to cores from a clay-gel water-base drilling fluid treated with various commercial viscosity reducers and chemical fluid-loss control agents. The dynamic fluid-. loss rates to cores are compared with the standard API filter-loss values at several different levels of additive concentration. Dynamic filtration rates were obtained in each experiment under two different simulated wellbore conditions: (1) filtration just above the bit through a new mud cake laid down dynamically on a freshly drilled formation and (2) filtration up-hole through a mud cake formed by deposition of a static filter cake on top of the initial dynamically formed cake. The latter case corresponds to the bottom-hole conditions existing above the bit when mud circulation is restarted after a stand of pipe has been added or a round trip has been made to change the bit. Except for the short-duration, high-rate filtration beneath the bit where no mud cake can form, these two conditions probably represent the two extremes of dynamic filtration. Because thickness of a dynamic mud cake formed on freshly exposed formation is limited by the shearing action of the mud stream, the filtration rate for this condition is high. On the other hand, once circulation is stopped and a static mud cake forms on top of the dynamic cake, re-starting circulation has only a small effect on the cake properties and filtration rate is much lower thereafter. A discussion of the mechanics of mud-cake deposition and dynamic filtration is outside the scope of this paper but may be found in more detail in publications by prior investigators. APPARATUS AND EXPERIMENTAL CONDITIONS The test equipment used to simulate the dynamic flow conditions existing during drilling was a modification of that described previously by Krueger and Vogel: A schematic flow diagram is shown in Fig. 1. In general, a power-driven, high-pressure mud pump capable of delivering up to 60 gallmin was used to circulate drilling fluid parallel to the faces of 1-in. diameter sandstone cores mounted in a 2 3/4-in. ID high-pressure test cell. Pump rates were controlled by means of a magnetic clutch to maintain an average axial fluid velocity of 110 ft/min in the annular space between the cell wall and a 1 1/2-in. rod positioned on the center line of the cell. The core specimens were Berea sandstone plugs sealed with plastic inside 1 1/8-in. OD tubes and were fluid-saturated prior to use. Burettes were used to accumulate fluid discharged from the cores. The mud sump shown was used for treatment and storage of the drilling-fluid samples during a particular test. The valve arrangement permitted either (1) circulating drilling fluid through the by-pass line while treating with

By P. J. Jacquard, C. Jain

Interpreting pressure measurements is one of the fundamental problems in the operation of oil reservoirs. The principal methods and means of study zuhich are currently used are reviewed. Emphasis is placed on the necessity of improving the quality of the information to turn it to the best possible account. One of the important aspects of the problem is the development of a system of automatic interpretation of the pressure measurements. The proposed method aims at this objective: starting from the relation which exists between a local perturbation of permeability and its effect on the velocity potentials in the wells, we determine by successive approximation the modifications to be made to the permeability map by fitting the least squares between the measured pressures and the pressures indicated by the mathematical model. The method has already been successfully employed in the case of heterogeneous reservoirs of radial- circular symmetry. Its application is extended here to the two-dimensional case, and is illustrated by two examples, for which the results are presented. The conditions required for the method to become fully operational are likewise analyzed. I — INTRODUCTION One of the basic problems of production and recovery from oil fields is interpreting pressure measurements made in wells in the single-fluid-phase regime. Simplifying assumptions, for example supposing the reservoir to be homogeneous, make it possible to use more or less simple methods which permit the estimation, from these pressure measurements, of a mean value of the permeability around the wells. Considering the actual heterogeneity of the majority of reservoirs, and the phenomena of interference between wells, these methods are only indicative. Much has been published on the studies of different cases of comparatively simple heterogeneity: some have discussed the radial heterogeneity around a single wel1,l or vertical heterogeneity.2 The results of these works have shown the influence of variations of permeability on the pressure, but unfortunately they are not very useful in practice because they all are concerned with the phenomena around a single well, without interference between wells, and they correspond to relatively simple and theoretical schemes. These studies of reservoirs or parts of reservoirs on a larger scale are made by the electric analyzer or digital model. We define a permeability map and a porosity map, then reproduce the production history of the wells on the wells of the model, and note the corresponding pressures. These pressures are then compared with actuality, and the discrepancies observed are analyzed. From this analysis we deduce the modifications to be made to the maps of permeability and porosity, and repeat until the coincidence between the pressures indicated by the model and the actually observed pressures is considered adequate. We have adjusted the model. Obviously, in this method of investigation, everything depends on the formula which permits the modification of the permeability to approach the adjustment. Considering the complicated nature of the problem, some oversimplified formulas are poorly adapted to reaching a good adjustment. For example, we have shown that the elementary operation of increasing the permeability not far from a producing well to compensate for too low pressures in the well can, in certain cases, express itself by an effect exactly opposite. 3 The project described here is for a system where we begin with the pressure measurements and the several known parameters of the reservoir, and develop the most probable permeability map, taking account of the measurements available and a subdivision of the reservoir fixed a priori. Ideally, this system is conceived as one in which no manual intervention would be necessary. The model simulating the reservoir is only one part of the whole system, and it is neither the longest nor the most complex part. The need to integrate the model into an aggregate of much more extensive processes has led to the adoption of the digital solution, even though a solution combining the digital and the analog is perfectly conceivable. The simulating model is in that case no more

Jan 1, 1966

By F. D. Everett

This report summarizes the results of a nationwide investigation completed in 1964 to determine the nonferrous base metal ore reserves and potential sources of ore and to evaluate criteria for their ultimate exploitation. Engineers of the Bureau of Mines contacted mining company officials, reviewed reports and Government records, and where necessary made personal appraisals in arriving at the results. The estimates are presented by metals in ores in geographic regions and include some of the problems affecting the reserves and potential sources. The recoverable metal in the measured ore category and in the total ore reserves was estimated as follows: [ ] At the 1963 rate of domestic mine production these total reserves would be adequate to provide copper for 62 years, lead for 121 years, and zinc for 42 years. Data also are given for gold, silver, and other coproducts. Reserve estimates greatly exceed those of previous investigations; some prior estimates of copper reserves are included for comparison (table 23). Projections of requirements for base metals indicated the United States will need approximately 45 percent more copper in 1970 and 110 percent more by 1980 than was consumed in 1960; similar projections for lead indicate increases of 20 percent by 1970 and 45 percent by 1980; zinc projections are 40 percent more by 1970 and 90 percent by 1980. Much of the production of gold and silver is a coproduct of base metals recovery and the projected need for the precious metals exceeds all the United States can produce. Some problems of the industry are mentioned. A graphic evaluation of the economic availability of the reserve and potential sources is shown.

Jan 1, 1967

By John L. Halls

INTRODUCTION In this section, it is assumed that the reader is an engineer with sufficient training in underground mining work, preferably with budgetary control, to understand the mining methods outlined in other sections of this handbook. The mining-method descriptions are not repeated herein; only sufficient information is provided to enable the reader to comprehend the development of the costs presented. All costs are in 1977 US dollars, except where explicitly stated otherwise. CAPITAL INVESTMENT The capital investment in the underground mining portion of any mining property includes the following: 1) The development of original access involving adits, shafts, declines, etc. It includes the necessary equipment for transporting men, materials, and rock. 2) The purchase of mine equipment including loaders, underground haulage equipment, fans, pumps, electrical distribution, surface facilities associated with the underground mine, etc. 3) Sufficient preproduction mine development to assure steadily increasing production after startup. De- pending upon the mining method used, the preproduction development should provide a supply of three months to one year of ore that is developed and is ready to be stoped. Underground development also includes excavations other than shaft stations, loading pockets, sumps, etc., which usually are associated with the means of access and are excavated by the contractor. These excavations could include a crusher cavern, an ore- storage pocket, and underground workshops that may or may not be included by the shaft-sinking contractor. Portions of these could be delayed until after production begins, but it is preferable to complete them during the development phase, so there is no interference with the production buildup. 4) The staff and labor costs for all phases from inception through final production. 5) The provision of mine-surface equipment and facilities strictly applicable to the underground portion of the operation. The required facilities include a changehouse with a lamp room, a first-aid station, compressors, an electrical substation, workshops, a ware- house, water pipelines to the concentrator, water storage tanks, explosive storage, etc. A concrete-batch plant, a sand-fill plant, and boilers for heating may be required. 6) Other direct and indirect costs. 7) Engineering, design, and procurement costs. 8) Contingency allocations. 9) Contractor's fees, startup costs, and owner's costs. Original Access As part of a study for the US Bureau of Mines, Dravo Corp. conducted an extensive literature research survey covering underground operations in the United States between 1963 and 1973. Table 1 is compiled from the section of that study pertaining to the types of access to underground mines. Table 1 does not include distances attributable to the deepening of existing shafts, nor does it include shafts bored by raise drills or downhole machines that need existing underground workings for the disposal of the cuttings. During the period under review in the report ( 1963 through 1973). concrete-lined circular vertical shafts were the predominant means of providing the first access to a new underground mine; these shafts accounted for 80% of the original access in terms of the number of accesses completed, and 75% in terms of the total verti- cal linear distances. The inside diameters of the conventional circular shafts ranged from 3.7 to 7.0 m (12 to 23 ft). Most (72% ) of these conventional shafts were for production,

Jan 1, 1982

By Eric R. Bauer

The ground control aspects of extended depth-of-cut mining are presented in this U.S. Bureau of Mines report. A trend analysis of extended cut approvals was performed. A comparative review of roof fall fatalities for extended and nonextended cut mining is included. Current ground control guidelines for extended cut approval are summarized. The problems and concerns of this extraction system are addressed, and typical extended cutting face operations are described.

Jan 1, 1993

Shane is enjoying his new work. Six months ago, he was stocking shelves at his local supermarket and decided to make the big move to a job in mining with more challenge and, of course, more dollars. He's been through his inductions, received his training tickets and is now working in a crew of eight underground at a fly-in, fly-out (FIFO) operation. There are many more systems and processes here than in his retail job, and Shane's comfortable that his safety is being looked after. He is enjoying the continually changing work and conditions, it makes the job interesting. It's taking some time to get used to the roster and he is worn out by changeover, but he gets more time with friends and family during R & R.   Generally, the mining industry has a maturing safety culture and well developed systems. This sometimes lulls people into a false sense of security. Safety systems cannot anticipate every possible situation, nor can they replace people's perception, thinking and decision-making. To manage safety, it's critical to find the right balance between dependence on systems and a healthy fear and respect of risks we face.   As safety standards are raised, systems tend to get more thorough and complex. When a new person joins a mining crew, we induct and train them to provide the information they need. As labour availability again becomes short, and many new people join our industry, we shouldn't assume they know the fundamentals. We need to explain not only what they are expected to do, but why doing what we ask and expect will keep them safe. We must equip people to deal with both the routine and the unexpected.   This presentation explores the challenges of balancing a structured, systematic approach to safety with the need to also equip people to deal effectively with risks everyday in dynamic and extraordinary situations.   Session purpose Introduce participants to a way of looking at risk from a different perspective, as a force for change and progress, if managed well. Demonstrate that risk is something we need to engage with emotionally as well as physically, if we want our risk management efforts to be successful. This purpose will be achieved through an entertaining and engaging presentation, using photos and case studies. The session will initiate interest to explore new ways of thinking about risk and generate discussion about the balance between people and systems. What is the right balance and why getting it right enhances the safety culture, while getting it wrong can impact on safety, business performance and sustainability.

Jun 1, 2010

By J Lane, D J. Barker, B Pei

Queensland Alumina Limited (QAL) is the worldÆs largest producer of smelter grade alumina, located in Gladstone, Queensland, Australia. The plant employs evaporative cooling towers for waste heat rejection. Process water requirements include red mud residue disposal, steam venting to the atmosphere and Calcination feed moisture. Raw (untreated) water consumption in 2001 was 37 700 m3/d or 3.8 m3 per tonne of production. The Gladstone region experienced a water shortage in the period 2001 to 2003, resulting in progressive water restrictions. Industry operated under a ten per cent restriction from April 2002 and in November 2002 a 25 per cent restriction came in force. The maximum restriction level of 50 per cent was anticipated for the middle of 2003. Water restrictions of these magnitudes have the potential to result in significant production limitations, which would have major economic consequences for QALÆs owners, customers, suppliers and employees. Therefore it was imperative that measures be found to mitigate the impact of these restrictions. Furthermore, as one of the largest water users in the Gladstone region, QAL had an obligation to the community to minimise water usage as much as possible. A thorough analysis of water usage on site was conducted, focussing on all water streams leaving the plant. The philosophy used was that by minimising water outputs, the inputs would follow suit. Where possible, preference was given to solutions that provided lasting water savings. This occurs when the value of the water saving justifies the project cost, irrespective of water restrictions. By June 2002 an average water saving of 19 per cent was achieved, almost double the required saving. By end November 2002 further projects had increased the total water saving to 29 per cent, mainly through the re-use of GladstoneÆs municipal treated effluent as wash water. Further measures to reach the target of 50 per cent reduction were investigated. The evaporative cooling system was to be replaced with seawater cooling, using cooling towers to minimise the seawater pumping cost. Another benefit of this concept was the ability to dispose of the cooling tower bleed stream with the existing system for neutralised red mud disposal. This would avoid the need for an additional environmental outfall from the plant. In February 2003 the Gladstone region received over 500 mm of rain, which boosted water reserves to five years supply at forecast usage rates. This led to the lifting of all water restriction. As most of the implemented water savings measures are economically viable in the absence of water restrictions, raw water usage at QAL is still less than 75 per cent of pre-2002 levels.

Jan 1, 2003

By AIME AIME

REGISTRATION and licensing of engineers is now being given consideration by a special committee of the Institute, authorized at the March meeting of the Board of Directors. The subject is one that has recently been or is now actively before engineering organizations in many of the States of the Union. In Washington, D. C., the Washington Society of Engineers and the local sections of ten national engineering societies, including the A.I.M.E., recently had a joint committee investigate the subject: this committee formulating a proposed law that has been presented to Washington engineers for their consideration. At the same time, the committee has summarized the reasons for and against registration of engineers in Washington, D. C. As many of these reasons are of more than local application, they are here reprinted so that all members of the A.I.M.E. may be informed on the subject. It is expected that some report of the Institute's Committee on Registration, State Councils and Professional Development will he made at some forthcoming meeting of the Board of Directors.

Jan 1, 1932

By J. Visman

FOR more than 25 years evaluations of coal cleaning units have appeared in many publications, and during this time considerable progress has been made in developing the theory and techniques of calculating washery results. A variety of characteristics have been defined over the years, many receiving general recognition during the first post-war Coal Preparation Conference in Paris in 1950. Coal preparation has become a science, and the approach to preparation problems is being revolutionized. Formerly, for example, if a coal operator wanted to know the performance of a given cleaning unit for a particular grade of his run-of-mine, he either shipped a carload to the manufacturer for a test run or relied on a report of a test carried out on a coal similar to the one he intended to clean. In modern practice the expensive, time-consuming test work generally can be avoided if the washability curves of the coal in question and the error curve of the cleaner are known. Normally a guarantee can be given on the strength of this information. General acceptance of modern standards has thus reduced the need for pilot-scale models of existing types of coal cleaners. Needless to say, the method requires exhaustive and accurate information on the cleaning unit and on all the additional circumstances affecting its results, in- formation that ultimately can be secured only from actual tests made in the laboratory or in the washery.

Jan 10, 1954

By C. T. Yavuz

Higher environmental standards have made the removal of arsenic from water an important problem for environmental engineering. Iron oxide is a particularly interesting sorbent to consider for this application. Its magnetic properties allow relatively routine dispersal and recovery of the adsorbent into and from groundwater or industrial processing facilities; in addition, iron oxide has strong and specific interactions with both As(III) and As(V). Finally, this material can be produced with nanoscale dimensions which enhance both its capacity and removal. The objective of this study was to evaluate the potential arsenic adsorption by nanoscale iron oxides, specifically magnetite (Fe3O4) nanoparticles. We focused on the effect of magnetite particle size on the adsorption and desorption behavior of As(III) and As(V). The results show that the nanoparticle size has a dramatic effect on the adsorption and desorption of arsenic. As particle size is decreased from 300 nm to 12 nm the adsorption capacities for both As(III) and As(V) increase nearly 1000 times. Interestingly, this increase is more than expected from simple considerations of surface area and suggest that nanoscale iron oxide materials sorb arsenic through different means than bulk systems. The desorption process however, exhibits some hysteresis with the effect becoming more pronounced with small nanoparticles. This hysteresis most likely results from a higher arsenic affinity for magnetite nanoparticles. This work suggests that magnetite nanocrystals and magnetic separations offer a promising method for arsenic removal.

Jan 1, 2006

By Larkings RH

The high gas emissions associated with the depth of mining and very high coal extraction at some Australian Collieries have provided a need to investigate the influence of geological and mining conditions on levels of gassiness. The introduction of longwall extraction in particular is associated with complex strata control problems and quick changes in gassiness. To this stage of Australian coal mining, no standard method has been developed to predict the different levels of gassiness associated with the various geological and mining conditions; and the relationship between coal output and total methane make has not been established. For local conditions, with a large number of coal seams lying in close proximity to the working seam, the significant contribution of gas emissions from adjacent strata was expected, especially as strata relaxation occurred during longwall mining. This depends mainly on geological conditions, strata control and coal production. For the deepest of the B.H.P. Collieries in the Newcastle region, the relationship between coal output and total methane make has been investigated by systematic gas balance measurement during longwall extraction. The computer method of iteration was used to approximate the mathematical equation from the initial graphs of coal production versus quantity of methane in the ventilation system for various strata conditions. The angle of caving was established for local geological and mining conditions, for planning and design of the positions of cross measure boreholes.

Jan 1, 1986

By Mathews K. E, Willstead T. V C

Initial glory holing was followed by sublevel stoping, with a small proportion of total production mined by shrink and cut-and-fill methods.The sublevel stoping method was successfully modified to cater for altering ground conditions encountered at increasing depths. At present, 94 per cent of production comes from sublevel stopes. The evolution of this mining method and current techniques and practices is outlined. A combined shrink and,sublevel benching method was also developed to increase the mining rate of narrow orebodies over the standard stoping lift of 380 ft. Pillar recovery and stope filling operations have been continuously modified to suit the relIuirements of a rapidly developing mine.INTRODUCTIONOre production commenced at Mount Isa Mines in June 1931. Since then production has increased from approximately 2,500 tons of lead ores per mine day to the current 11,000 tons of sulphide ores per mine day comprising 3,100 tons of lead ore and 7,900 tons of copper ore. The early planners selected sublevel stoping with ring drilling for ore breaking as the most efficient and economical for Mount Isa conditions: This method satisfied requirements for:1. a low cost mining method for the comparatively low grade ores,2. a stoping sequence allowing development, stope preparation, breaking and drawing of ore to proceed concurrently,3. a method of extraction in which broken ore in the stopes would be kept to a minimum because of adverse effects of oxidation on mill metallurgy and...

Jan 1, 1961

By Marvin J. Udy

THE preparation of this paper is in response to many requests for in-formation on the mining and smelting developments which have been carried on for the past three years or more by the Chromium Mining and Smelting Corporation of Canada. By way of introduction, the following paragraphs, relating to the early history and present status of the chrome-mining industry in the United States, are of interest. They are quoted from Bulletin No. 76 of the California State Mining Bureau, published in August, 1918: 'Chromium was discovered about 1797 by a French chemist, Louis Nicolaus Vauquelin, in ore from Siberia. From that time until 1827, the Urals, in the region of Ekaterinburg, supplied the chromium used in . Europe. In the summer of 1827, as the historian advises us, Isaac Tyson, Jr., saw in a Baltimore market-place a cart containing a cider barrel, which was held from rolling about by some heavy black stones. He had made a study of such stones at the first-known American locality, the Bare hills near his father's home, six miles from Baltimore, and he recognized the black stones as chromite. On inquiry, he found the chromite came from the Reed farm in Harford county, 27 miles northeast of Baltimore. At this time, Tyson was one of the very few men in the country who knew the value of chromite, and in the next few years he took full advantage of this knowledge. He immediately bought the Reed farm. He found about 30 tons of float-ore on the surface, but there was no outcrop of ore in place. Never-theless, he sank a shaft, and at a depth of eight feet struck an ore-pocket which proved to be 80 ft. long, 25 ft. wide, and 8 ft. in maximum thickness. His next discovery was of placer chromite in the sands in the beds of brooks on an estate called Soldiers' Delight, 16 miles northwest of Baltimore. Thus far, Tyson's observations had shown him that chromite occurred apparently only in serpentine areas. His explorations were now leading him farther afield. In 1828, he found on the Wood Farm, in Lancaster county, Pennsylvania, a deposit of float chromite which led him to lease the ore-right of the farm, which he finally purChased in 1832. Here he developed the famous Wood mine, the largest single producer of chromite in the world.

Jan 1, 1938

By Osvaldo A. Bascur, J. P. Kennedy

Companies have installed powerful desktops for their personnel and instrumentation and control systems in their plants. These desktops are, in many cases, connected to a company intranet. Still, process engineers have to obtain their data manually. Engineers use process calculations from manually calculated averages from the plant; field operators collect equipment data on log sheets; and maintenance engineers collect critical information on log sheets. All of this information resides in individual machines. What are the strategic tools that will enable collaboration between them? How can operators, engineers, and managers access plant information to proactively increase their effectiveness in process troubleshooting, plant debottleneclung, aligning with business strategic and customer demand, satisfying environmental and safety regulations, developing capital projects, and implementing control strategies? A nonintrusive environment at the desktop is required to provide the process information to these workers. How can value be added to MS Windows technologies with the legacy systems at a minimum cost? There is no straight answer; however, there is a proven framework to leverage the large investments in new technologies. Objects and components are changing the way everyone relates to their computer and networks. Three examples will be described to demonstrate paradigm change. Today, process engineers can access data at the required level of detail for analysis of critical process variables at their desk or remotely. 1. Process Troubleshooting and Analysis: The engineer can develop an inferential calculation, trigger a process advisor to deter- mine the behavior of the units for the last day, and get the population of a set of batches (heats, blocks, rolls, sheets, etc). 2. Process Control and Optimization: The engineer can connect to a process simulator at steady state or a dynamic simulator of the process to evaluate new control strategies or process unit line-ups and use the process simulator as a process observer for fault diagnosis. 3. Collaboration with Accounting and Maintenance: The engineer can review reconciled data and the process mass balances, suggest maintenance cleaning or recalibration of flowmeters, and evaluate key control performance of all advanced controls.

Jan 1, 1999

By Waldemar Lindgren, Clyde P. Ross

To the miner, as well as to the geologist, the eastern part of Cuba is a most interesting region. Here we find, in contrast to the moderate relief predominating elsewhere in the island, an imposing mountain range, the Sierra Maestra, extending east and west parallel to the coast, its precipitous front facing the blue Caribbean Sea. In a geological sense this range is largely an unknown land, the only well-explored region being that in the vicinity of Santiago. The range also contains the most important mineral deposits of the island. They comprise, first, a series of iron deposits yielding a partly hematitized magnetite with low content of phosphorus; second, a remarkable copper-bearing vein at El Cobre; and third, various manganese deposits. Probably more deposits will be found, for the larger and western part of the range is as yet little explored and its slopes are covered by a thick tropical jungle. The following notes are based on a short visit by the senior author in January and February of 1914 to the mines at Daiquiri, El Cobre, and Mayari. For many courtesies and great assistance he is deeply obliged to Charles F. Rand, President of the Spanish-American Iron CO.; to George W. Pfeiffer, General Manager, and to the several members of his staff. Geological Features of the Sierra Maestra For our knowledge of the geology of the Sierra Maestra we are indebted to reconnaissance work by Fernandez de Castro, R. T. Hill, Mr. C. Hayes, T. W. Vaughan, and A. C. Spencer. The summary by the latter three geologists furnishes the best guide to the region.' The range is undoubtedly outlined by a great east-west dislocation. Its southern slope drops abruptly to the sea, while on the north side a much gentler declivity leads down to the rolling plateau of Tertiary limestone which occupies much of the adjacent part of the island. Viewed

Jan 1, 1916

By D. S. Hutton, W. C. Leslie

Thermal etch patterns developed on poly crystalline 3.5 pct Si-Fe by heating in hydrogen or in argon have been examined. The most prominent feature of the etching is the development of striations on grains with (100) planes near the plane of the surface. These striations are probably produced by the resoution of a random, high-energy plane into (100) facets of lower energy. THE thermal etching of iron and iron-base alloys has a long history. The phenomenon was observed by Osmondl more than 70 years ago. The literature on thermal etching between that time and 1951 was reviewed by Olney,2 and a briefer review appeared in 1958. 3 The only articles which have been found dealing with the thermal etching of silicon iron are those of Dunn and Lionetti4 and of Dunn, Daniels, and Bolton,5 and they reported only grain boundary etching. EXPERIMENTAL PROCEDURES A cast 3.5 pet Si-Fe alloy was given a metallo-graphic polish and etch, then placed in flowing purified hydrogen for 6 hr at 2200°F. The same specimen was later repolished and etched to remove the thermal etching. The specimen was then held in flowing purified argon at 2200°F for 72 hr. In both instances the specimen was rapidly cooled by being pulled up quickly into the cold zone of the furnace. All photomicrographs shown are of the surface as removed from the furnace. Oblique illumination was essential for observation of the thermal-etching effects with a light microscope and was used for all the photomicrographs. RESULTS AND DISCUSSION Grain boundary etching, grain boundary movement, and contouring within grains are illustrated in Fig. 1. The contours within a single grain followed behind the advancing grain boundary. To determine the average contour interval, or step height, white light was used in an interference microscope. The steps were of the correct magnitude to separate while light into its spectrum of colors. A green light was focused at the top of a contoured area, shifting to red across the field. By using the difference in the dominant wave length of red and green light,6 and counting the number of steps across the area, it was possible to obtain a value of about 80A for the average step height. Laue back-reflection patterns of four grains with contour lines showed that the grains had a (100) plane slightly inclined to the plane of the surface (± 5 deg). Insofar as this could be determined from their irregular traces, the contour lines within a grain had a common direction, <100> ± 5 deg.

Jan 1, 1961