Search Documents

By Fred V. Carrillo

Of the total quantity of secondary copper and zinc that became obsolete in the United States from 19b1 through 1970, more than 11 million tons of copper and 10 million tons of zinc were not recovered. These estimates are based on a study of the flow and recovery of old copper and zinc scrap by consumption end-use. This report describes (1) where copper and zinc are being used; (2) when they become obsolete and available as secondary metal; (3) how they are being collected for recycling; and (4) how much might be recovered from scrap that presently is not being recycled.

Jan 1, 1974

By David L. Sprott

This paper presents an evaluation of underground-to-surface haulage options for a relatively large deposit. Specifically, it presents a recommended haulage option to provide the greatest value to the Project. Options considered included conventional truck, trolley-truck, conveying and shaft hoisting. The work was done at the level of a preliminary assessment as input to an internal pre-feasibility study. The Base Case for the analysis in this study was a Long Hole Open Stoping option (LHOS) using conventional truck haulage. Two scenarios were considered for the evaluation and included: 1. The current resource to ~700 m depth. 2. An expanded resource to ~825 m depth. The haulage options evaluated included three trucking options, three conveyor options and two shaft options. The paper presents the results from evaluating these options within the two mining scenarios using a Discounted Project Cost (DPC) comparison. Recommendations are made for the options that will provide the greatest overall value to the project.

May 1, 2008

Lime and Marble Limited was founded by the late T J McKee OBE and his family in 1935. The Company had its base in the high grade marble deposits on Takaka Hill, and was also shipping crushed limestone to the Auckland glass works, and supplying burnt lime for industry.

Jan 1, 1998

By Mark J. Dowiak, Daniel Threlfall

The disposal of hazardous chemical wastes will be one of the major environmental issues of the 1980s. About 45 Mt of hazardous wastes are produced yearly. One major aspect of the problem is the siting, design, and construction of' environmentally acceptable disposal facilities to accommodate this huge volume of material. Surface mines have been considered attractive for development as disposal sites for several reasons. • Surface mines offer an open pit that can conveniently serve as a repository for wastes. This could represent a significant economic, savings when compared with sites on undisturbed lands that might require extensive excavation or embankment construction. • Surface mines often have an abundance of mine spoil available that could potentially serve as construction material. This could result in a significant economic advantage over other sites that might require extensive amounts of construction material to be excavated or hauled in. • Operation of a commercial disposal facility in a surface mine can reduce or totally alleviate reclamation costs. • For an abandoned surface mine, conversion into a disposal facility could represent a positive form of land use and may provide a means for reclaiming lands that would otherwise remain unreclaimed. Despite these positive reasons, there are many technical factors associated with surface raining that can make the prospect of disposal site development an uncertain one. Before discussing factors associated with mining that can present siting, design, or construction problems, some understanding of the basic components of a chemical waste disposal facility is necessary.

Jan 2, 1981

By W. R. Ingalls

THE MAJOR use of spelter has always been for the coating of iron and steel products, the process of coating being known as "galvanizing" and the products themselves as "galvanized," except for a couple of years during the war, when the consumption for brass making became superior, in the United States at least, owing to military demands. Since 1919, however, the consumption of spelter for galvanizing has regained the premier position, but not with such a long lead over brass making as previous to the war. The last development is ascribable to two main reasons, viz., an increased demand for brass in new industries, especially automobile manufacturing; and a diminished use of spelter per unit of iron and steel galvanized. MAJOR IMPORTANCE OF SUBJECT The last mentioned matter has already been the subject of some discussion and of some literature. The galvanizers have been charged with deliberately thinning their zinc coatings, with the consequence of producing inferior goods and thereby jeopardizing the whole galvanizing business. Zinc producers have been concerned about this, out of consideration of both the less use of zinc per unit of iron and steel and the fear that, the number of units produced may be curtailed. It has been argued, among other things, that the present policy of American galvanizers would impair their ability to compete in foreign markets with British galvanizers, who have been represented as making a superior product.

Jan 7, 1923

By R. H. Rice

Turbo blowers for blast-furnace blowing have now been in use for some years, and a review of the experience gained and the present state of progress may be interesting.

Jan 1, 1915

By Tyler MA

If the record of maj or proj ects in Australia is taken into account, it is apparent, the proper planning of an industrial relations strategy for many such projects has been ill considered by project developers. The recognition of the need to develop a plan from the initial feasibility study has been forced on those promoting new projects by the publicity given to the Australian industrial relations record. The delays in delivery caused by factors supposedly out of the project's control are often given for non-performance of contract and used as an excuse for limiting further development. Many of the problems experienced in project development can be overcome with sound industrial relations planning. The promises given in the euphoria of the early stages of a project relating to price and delivery often become a burden for the future because the complexities of the Australian Industrial Relations Systems are not understood or considered. The recognition by senior executives of their responsibilities in this area will contribute greatly to a new era of project development.

Jan 1, 1983

By Russell Parrott

Acoustic techniques offer a rapid, economical, non-intrusive method of obtaining information about the stratigraphy and properties of seafloor sediments. During the past decade there has been a dramatic increase in the level of sophistication of high resolution seismic reflection equipment used for seabed and subsurface studies and in the signal processing techniques applied to the data collected with these systems. Processing of data from acoustic sources with repeatable and calibrated output, allows quantitative measures of the reflection coefficient, acoustic attenuation and scattering parameters of the sediments on the seafloor. Graphic recordings of seismic reflection data emphasize the coherent portion of the reflected energy for qualitative estimate of sediment properties and subsurface stratigraphy. Through application of signal processing techniques, quantitative information can be extracted from the coherent and incoherent components of seismic reflection data for estimation of surface character and sediment properties. These calculated parameters can be applied through interpolation between areas of available groundtruth. Acoustic techniques are used extensively to establish the regional geological framework of project areas and can also be used to extrapolate available groundtruth data into previously unsampled areas, and to optimize the design of a sampling program to provide the necessary groundtruth for the survey area.

Jan 1, 1985

By Charles E. Nelson

THIS paper will outline briefly the practices commonly followed in this country for the melting and refining of magnesium and its alloys. The processes used for the various forms of primary magnesium, as jar as there are differences in the physical shape or behavior, will be discussed. The refining of general fine scrap or secondary magnesium was presented in an earlier paper and will be discussed briefly.1 Inasmuch as the use of fluxes is an essential part of all the melting and refining processes, this paper will deal with these in sufficient detail to point out their unique characteristics, in order to make their use more effective. The outline of this discussion will closely follow that of an earlier paper,2 with such changes and additions as seem necessary to bring it up to date. TYPES OF MELTING PRACTICE All melting and refining processes for magnesium and its alloys require the use of fluxes. These fluxes have a magnesium chloride base and other halide salts or oxides are added to give a density or behavior exactly suited to the particular melting practice. The successful handling of magnesium depends upon the proper use of the correct fluxes. There are four general methods of melting, summarized in the following paragraphs and treated in more detail in the section on Melting and Refining. Open-pot Method The open-pot method makes use of No. 230 flux, which provides protection during melting and a molten pool of flux into which the solid magnesium melts. The flux is stirred through the molten metal bath and agglomerates oxide or similar foreign bodies;, on quiet standing, it separates away, leaving the refined metal ball floating in an encircling layer of molten flux. It forms only a thin fluid film over the surface of the molten metal, which may be parted for hand-ladling processes and tends to cover the metal again after the ladle is removed. A very light dusting of the pot surface with fresh flux immediately after the ladle is removed is desirable. The open-pot method is used generally in the following processes: (I) alloying and remelting in the production of ingot, (2) in sand foundries for premelting and to a smaller extent for the production of small castings, (3) in permanent-mold founding for premelting and also direct ladling to castings, (4) for continuous methods of preparing metal in the production of billets or ingots from which wrought products are fabricated, (5) in general scrap recovery. Crucible Process The crucible process makes use of No. 310 flux, which has the property of being thinly fluid at the start, to provide protection and refining qualities, and then drys out or thickens after a time, leaving a protecting crust on the pot surface until the time of casting. At that time it can be readily skimmed off or held back, thus allowing the contents of the crucible to

Jan 1, 1946

By Peter Zhang

Shield recovery in a longwall move is normally conducted from tailgate to headgate. However, if the face is wide and the immediate roof is weak, difficult conditions with considerable roof sag, excessive shield load, and local roof falls could occur as the shield recovery proceeds to the middle of the face, causing delays in shield recovery. The situation could be aggravated when a pre-driven longwall recovery room is employed. Alternatively, a bi-directional approach for shield recovery, i.e. shield recovery starting from the middle of the face towards both tailgate and headgate, can alleviate the roof sag significantly by quickly withdrawing the shields towards the lower abutment pressure zones at the headgate and tailgate sides. In this case, the bi-directional shield recovery approach was used in a longwall move for a 1450 ft wide face under weak roof conditions. Shields were successfully withdrawn within five days without experiencing significant roof sag. The time-dependent roof-to-floor convergence, shield pressure, and roof conditions were monitored during shield recovery. 3-D finite element modeling was conducted prior to longwall move to evaluate the difference between a uni-directional and a bi-directional shield recovery during a longwall face move. Vertical stress, yield zone in and around the recovery room, load on the shields, and convergence at the center of the shield canopy were obtained from computer modeling, and compared with the data from field monitoring. Finally, the advantages of the bi-directional shield recovery are discussed.

Jan 1, 2007

By W. N. Poundstone, P. C. Thakur

Introduction Horizontal drilling in coal mines is a relatively new technology. The earliest recorded drilling in the United States was done in 1958 at the Humphrey mine of Consolidation Coal Co. for degasification of coal seams. Spindler and Poundstone experimented with vertical and horizontal holes for several years. They concluded in 1960 that horizontal drilling in advance of underground mining appeared to offer the most promising prospect (for degasification) but effective and extensive application would be dependent upon the ability to drill long holes, possibly 300 to 600 m, with reasonably precise directional control and within practical cost limits (Spindler and Poundstone, 1960). Mining Research Division of Conoco Inc., the parent company of Consolidation Coal Co., began a research program in the early 1970s to achieve the above objective. The technology needed to drill nearly 300 m in advance of working faces was developed by 1975 and experiments on advance degasification with such deep holes began in 1976. Preliminary results of this research have already been published (Thakur and Davis, 1977). To date nearly 4.5 km of horizontal holes have been drilled for advance degasification and earlier results were reconfirmed. In summary, these are: • The greatest impact of these boreholes was felt in the face area where methane concentrations were reduced to nearly 0.3% in course of two to three months from original values of nearly 0.95%. • The methane concentration in the section return reduced to 50% of its original value immediately after the boreholes were completed, indicating a capture ratio of 50%. • The total methane emission in the section (rib and face emission plus the borehole production) did not increase but rather gradually declined with time. • Initial production from 300 m deep boreholes in the Pittsburgh seam varied from 3 m3/min to 6 m3/min but then slowly declined as workings advanced inby of the drill site (well head) exposing a larger surface area parallel to the borehole. Encouraged by these results, it was decided to design a horizontal drilling system that would be mobile and compatible with other face equipment. A mobile horizontal drill can be divided into three subsystems: the drill rig, the drill bit guidance system, and borehole surveying instruments. The drill rig provides the thrust and torque necessary to drill 75- to 100-mm diam holes up to 600 m deep and contains the mud circulation and gas cuttings separation systems. The drill bit guidance system guides the bit up, down, left, or right as desired. Borehole surveying instruments measure the pitch, roll, and azimuth of the borehole assembly. Additionally, it also indicates the thickness of coal between the borehole and the roof or floor of the coal seam. Thus, it becomes a powerful tool for locating the presence of faults, clay veins, sand channels, and the thickness of coal seam in advance of mining. In recent years, many other potential uses of horizontal boreholes have come to light, such as in situ gasification, longwall blasting, improved auger mining, and oil and gas production from shallow deposits. The purpose of this paper is to describe the hardware and procedure for drilling deep horizontal holes. The Drilling Rig [Figures 1 and 2] show the two components of the mobile drilling rig: the drill unit and the auxiliary unit. The equipment (except for the chassis) was designed by Conoco Inc. and fabricated by J. H. Fletcher and Co. of Huntington, WV. The drill unit. It is mounted on a four-wheel drive chassis driven by two Staffa hydraulic motors with chains. The tires are 369 X 457 mm in size and provide a ground clearance of 305 mm. The prime mover is a 30-kw explosion-proof electric motor which is used only for tramming. Once the unit is Crammed to the drill site, electric power is disconnected and hydraulic power from the auxiliary unit is turned on. Four floor jacks are used to level the machine and raise the drill head to the desired level. Two 5-t telescopic hydraulic props, one on each side, anchor the drill unit to the roof. The drill unit houses the feed carriage, the drilling console, 300 m of 3-m-long NQ, drill rods, and the electric cable reel for instruments. The feed carriage is mounted more or less centrally, has a feed of 3.3 m, and can swing laterally by ± 17°. It can also sump forward by 1.2 m. The drill head has a "through" chuck such that drill pipes can be fed from the side or back end. General specifications of the feed carriage are: [ ] The auxiliary unit. The chassis for the auxiliary unit is identical to the drill unit but the prime movers are two 30-kW explosion proof electric motors. It is equipped with a methane detector- activated switch so that power will be cut off at a preset methane concentration in the air. No anchoring props are needed for this unit. The auxiliary unit houses the hydraulic power pack, the water (mud) circulating pump, control boxes for electric motors, a trailing cable spool, and a steel tank which serves for water storage and closed-loop separation of drill cuttings and gas.

Jan 1, 1981

By B R, R Brooks, R Simcock, R Stewart

As environmental costs incurred by the mining industry become increasingly subject to critical analysis, new technology is necessary to ensure the further development of good relationships between the industry and community. Phytoremediation and phytomining are technologies that have the potential to capture the imagination and approval of the public. Phytoremediation , the in situ use of plants to extract heavy metals from a contaminated substrate, could offer an environmentally and cost-friendly alternative to traditional remediation techniques. Phytomining is the in situ removal of metals from a contaminated site or subeconomic orebody with the additional aim of recovering from the plant an economic amount of metal. Plants used in such operations, hyperaccumulators, accumulate large quantities of one or more target metals in their above-ground herbage. Upon harvesting and incineration, this plant material yields a low-volume, sulphide-free æbio-oreÆ, which can either be safely disposed of, or if the metal is of sufficient value, smelted. Investigations into the economics of phytomining nickel from ultramafic (serpentine) soils, showed that Alyssum bertolonii and Berkheya coddii could remove over 100 kg of nickel per hectare per annum from land with nickel concentrations well below the cut-off grade for conventional mining. It also appears possible to æinduceÆ the hyperaccumulation of gold into plants growing on gold tailings, or on stockpiled, low-grade gold ore. The plants used for phytoremediation and phytomining are useful colonisers as they are necessarily hardy and withstand extremes of salinity, metal toxicity and water stress that hinder the success of current revegetation procedures. As part of a rehabilitation operation, these plants may alter the geochemistry of a substrate making it more amenable to the growth of native species that should be used to restore a mining site to pre-operating conditions.

Jan 1, 1999

By Allen Kinney, P. T. Freeport

This paper presents the methodology for final wall-controlled blasting utilized at the Grasberg Mine. The resulting optimized slopes representa14%and17% increase to bench face angle (BFA) and inter-ramp slope angle (ISA), respectively. The corresponding increase in both copper and gold recovery was more than 40% greater than forecast for each material. The Grasberg open pit mine is located in the remote jungle province of West Papua Indonesia, at an elevation of 4,200 meters(13,780 ft).With a diameter of approximately 3.5km(2.2 mi), anddepthover1.2km(0.7 mi),P.T. Freeport Indonesia (PTFI)has mined billions of tons of rock from one of the world’s largest gold and copper deposits. Grasberg Operation and Engineering implemented a quality driven slope optimization program for the final pushback, with the goal to safely increase recoverable metal through steeper slopes, while utilizing existing infrastructure and equipment. This paper focuses on controlled blasting initiatives, blast monitoring, and as-built slope measurement tracking, although many groups contributed to the success of Grasberg slope optimization. The potential slope optimization area was divided into two sections based on geologic assessment: Area A at radial 200°-270° and Area B at radial 270°-360°. Original slope designs for areas A and B specified ISAs of 51° and 52°, respectively, with all BFAs in the pit at 70°. Through continuous development, collaboration and achievement, the Grasberg final pit accomplished a BFA increase to 80°for all areas, and an ISA increase from 51° to 56°in Area A, and 52°to 60° in Area B.

By J. J. Kollé

A compressed-water hydraulic pulse generator (HPG) for nonexplosive blasting of rock and concrete is described. Energy is stored in the HPG by compressing water to ultrahigh pressure. A large, fast-opening valve discharges the compressed water, resulting in a high-energy impulse. The HPG can be used for small-scale bench blasting by discharging the water through a nozzle that is closely fitted into a borehole. A bench blasting system requires an HPG, a drill and an indexing mechanism to allow insertion of the HPG nozzle into a drilled borehole. Systems with discharge energies ranging from 40 to 250 kJ have been used to excavate hard rock, including andesite, granite and quartzite. The largest system can excavate 15 t/h (16.5 stph) of massive quartzite based on a 2-min cycle time for hole drilling. Blasting with an ultrahigh -pressure hydraulic pulse generator was demonstrated as an effective means of excavating hard, massive rock under the confined conditions of a tunnel opening or underground sloping panel. Hydraulic blasting provides a continuous mechanized mining capability that is well suited for deep-level mining and urban excavation sites where explosives are prohibited.

Jan 1, 1998

By L. G. Margolin

INTRODUCTION In this paper we derive an expression to predict the onset of growth of a crack in a quasibrittle material. We employ an energy criterion, which was first proposed by Griffith (1920), and is essentially equivalent to the first two laws of thermodynamics. The criterion is applied to the elastic-plastic crack of Olesiak and Wnuk (1968), which is a three-dimensional generalization of the Dugdale (1960) crack. Our expression for the onset of growth differs in several respects from a criterion based on a crack in a brittle material (i.e., using linear elastic fracture mechanics) . Furthermore, the new features are in qualitative agreement with the experimental data. Among these new features are 1) the dependence of the apparent surface energy, or critical strain energy release rate on crack size (the shape of the R-curve); 2) the effect of in-plane stresses (i.e., the stresses that do not lead to any traction on the crack faces) on crack growth; and 3) a brittle-ductile transition. The energy criterion, as a necessary condition for crack growth, rests on a firm theoretical basis. However, its role as a sufficient condition is less secure. Several alternate criteria have been proposed as necessary and sufficient conditions for the onset of crack growth. We will contrast several of these, including critical strain (Olesiak and Wnuk, 1968; Goodier and Field, 1963) and crack opening displacement ("COD", Burdekin and Stone, 1966) with the energy criterion. We will show that these alternate approaches are inconsistent with the energy criterion, in the sense of being necessary conditions, and so should be rejected as criteria for growth--at least for the elastic-plastic crack.

Jan 1, 1984

By P S. Heithersay, M McGeough

The discovery of Olympic Dam in 1975 and, more recently, Prominent Hill in 2001 and Carrapateena in 2005 demonstrates the potential for world-class IOCG deposits in South Australia. Potential for further discovery of large IOCG mineral deposits in the Gawler Craton and the Curnamona Province is high because of continental-scale pervasive iron-rich alteration, crustal-scale structural preparation and unique magmatic-hydrothermal conditions. Recent exploration successes point to the effectiveness of new exploration tools and technologies to locate this style of mineralisation under cover. The gold endowment of these orebodies located in South Australia exceeds 75 Moz, with further discoveries to come. The lead time between discovery and development of the multi-million ounce Prominent Hill copper-gold mine in less than seven years demonstrates how quickly this style of deposit can be brought into production in South Australia. Clearly these long-life, multi- commodity IOCG deposits mines are an immediate exploration and future growth opportunity for the gold mining industry to replace ever depleting gold inventories.

Jan 1, 2007

By Martin S. Oudenhoven

This Bureau of Mines report presents the results of a microseismic study conducted in the Climax block cave mine at Climax, Colo. Rock noises created by caving were monitored and their sources located during a 3-month period. A planar array of seven accelerometers, located above the block of ore being caved, detected the rock noise. A computer was used to calculate the location of the microseismic activity, using a traveltime difference method. The accuracy of these locations was estimated to be ±20 feet. An analysis of the data taken during the recording period showed a concentration of microseismic events located in the wall of the cave panel. This concentration of events was found to occur in a "high-silica" geologic forma-tion that cut across the caving panel approximately 200 feet behind the undercut.

Jan 1, 1973

By Wi11iam I. Rau

In the recent past, there have been numerous projections of the capital requirements for additional mine and processing capacities required to meet projected non-Communist World demand for minerals during the next 15 years. A consensus judgment would place this currently at $14 billion per year, with the largest expenditures required for increases in aluminum and copper production. Until the early 1960's, internally-generated funds were used to finance nearly all of the large mining companies' capital requirements. Since that time, however, the enormous rise in capital costs per ton of capacity, accompanied by a relative stagnation in the financial condition of many of the major mining companies, have caused the industry to begin to rely on external sources for financing expansion, most notably, project financing from commercial banks and institutional lenders. Seven years ago, it was estimated that, in the five-year period 1972-1976,75% of the total capital requirements of $10 billion per year would come from internally-generated funds, with the balance to be provided by external sources. l There is little doubt that, in the coming decade, the percentage provided by external sources will increase. There should be little difficulty in attracting the necessary investment within the U.S., particularly in view of the expected continuation of companies in diverse industries seeking mineral investment opportunities. The more serious question lies in the availability of internal and external sources of funds for the expansion of mine and smelting capacity in the developing countries. Recently, R. F. Mikesell projected an average annual investment of $4.7 billion (in 1977 prices) over the 1977-1990 period would be required from foreign sources to expand metal producing capacity in developing countries. Mikesell concluded that external financing of mining projects in the developing world has averaged less than $1 billion per year over the past five years, thereby requiring more than a quadru1ling of this financing over the next decade.

Jan 1, 1978

By R. Guest

Reichert cone concentrators are used successfully in many applications, but have as yet not found favour in the gold mining industry on the Witwatersrand, because, for optimum operation, the cones need to have specially designed feed-preparation and circuit details. In addition, good liberation of the valuable minerals is essential. Gravity tests, in which a pilot plant was used on refractory gold ore, showed that 94 per cent of the gold could be extracted after gravity concentration and preferential grinding, roasting, and cyanidation of the concentrate, whereas 96 per cent could be extracted by flotation followed by the same preferential treatment. However, the capital and operating costs for gravity separation are expected to be considerably lower than those for flotation.

Jan 1, 1982

By J T. Patterson

The mining, quarrying and construction industries are often blamed for causing damage to residential-type structures when explosives are used. The claim experience for blasting vibration damage has been poor. This coverage is excluded from the Comprehensive General Liability (CGL) policy. To obtain this coverage, the policyholder must meet additional criteria and an additional premium must be paid. The risk management process offers the explosives user a technique for minimizing the risk of complaints and vibration damage claims on his insurance program and his cash flow. Case histories indicate that the vibration damage claims expense may be a lower risk than the risk of interference with production and cash flow. An annotated bibliography on risk management and defense of vibration damage claims is provided.

Jan 1, 1978