Search Documents

By G. S. Dobby, J. A. Finch

"I. INTRODUCTIONA significant development in flotation over the past few years has been the increasing industrial use of flotation columns, primarily in Canada. The column differs dramatically from conventional mechanical flotation machines, both in design end operating philosophy, which has been a principal reason for its slow acceptance by the mineral industry. Boutin, Tremblay and Wheeler (1. 2) developed the concept in the early 1960's and since then plant and laboratory columns have been marketed commercially by Column Flotation Company of Canada Ltd. In 1980-81 at Mines Gaspe, Quebec, three columns replaced 13 conventional cleaners in a molybdenum upgrading circuit, with superior results (3). Since then many of the copper producers in British Columbia have installed columns for copper and molybdenum cleaning, including Gibraltar, Lornex, Highmont and Island Copper. There now appears to be widespread interest in flotation columns.The column is particularly attractive for applications involving multiple cleaning stages and can upgrade In a single stage compared with several stages of mechanical cells. This results in simpler, more controllable circuits. Importantly, the column itself is well suited to computer control. A significant problem, however, has been that of translating laboratory data to plant performance. The purposes of this communication are to address the problem of column scale-up and to describe some of the transport mechanisms of a flotation column, leading to a kinetics based model.A schematic of a flotation column is shown in Figure]. Industrial columns are up to 13 m high and 0.3 to 1.8 m in cross section (either square or circular). Three zones can be identified:a collection zone, with feed entering 2 to 3 m below the top of the column and descending against rising bubbles generated at a gas sparger; a washing zone, where a packed bubble bed is generated by a downward flow of wash water; and a conventional froth (2 - 5 cm thick), the sole purpose of which is particle transport to the launder. The tailings withdrawal at the bottom of the column is controlled at a rate slightly greater than the feed flowrate (called a positive bias).An important element is the washwater, added just below the froth zone. The component of the washwater that flows downward (to make up the bias) is sufficient to prevent coalescence of rising gas bubbles. The packed bubble beg so generated is very efficient at suppressing gangue entrainment to the concentrate."

Jan 1, 1985

By N. Sahin, K. Baris, A. Ozarslan

This paper aims to assess the current and future role of coal in energy strategy of Turkey and evaluates the compatibility of the policies to the EU energy policy and strategy. The Turkish government set targets to utilize more coal reserves of the country in next decades. However, the country is also in the process of becoming an EU Member State, hence, it is expected that the energy policies have to comply with the EU. Moreover, Turkey ratified Kyoto Protocol, thus the country should limit greenhouse gas emissions. Clean Coal, Carbon Capture and Storage (CCS) technologies are expected to become an important instrument for the mid-term reduction of CO2 emissions from coal-fired power plants. An alternative technique to the conventional CCS methods is CO2 sequestration by mineral carbonation. Turkey has significant resources of magnesium silicate minerals (olivine, serpentine) deposits which can be utilised in CO2 sequestration by mineral carbonation method.

Jan 1, 2011

When xanthates or dithiophosphates are used as collectors in sulphide ore flotation, adsorbed species may be identified by gas chromatography of the volatile products formed during low temperature pyrolysis. For collector additions ,as low as 20 g/tonne of ore, pyrolysis of the flotation products usually gives' an olefin directly related to the particular xanthate or Aerofloat reagent used. The method is able to provide valuable qualitative and quantitative data relating to the extent of collector adsorption and the resulting changes in the hydrophilic or hydrophobic nature of the mineral surface.

Jan 1, 1974

By D. Neuschiltz, M. Witthaut, R. Cremer

"Metastable (Ti,Al)N coatings with fee structure have been shown to exhibit superior performance as compared to TiN under conditions of wear at elevated temperatures due to their better oxidation resistance and hardness. The oxidation resistance of these coatings increases significantly with increasing Al-content. However, the deposition of (Ti,Al)N films with Ti/ Al ratios below about 30/70 leads to a hexagonal structure which is not suitable for tribological coatings. Only little is known about the location of the cubic to hexagonal phase transition and hence about the optimum composition of (Ti,Al)N hard coatings.To determine the position of this transition, Tii-xAlxN films with different Ti/Al ratios were deposited on high speed steel at substrate temperatures between 100 and 700 °C by means of reactive MSIP. The composition of the films was determined by electron probe microanalysis (EPMA) and X-ray photoelectron spectroscopy (XPS), the crystallographic structure by thin film X-ray diffraction (XRD).It could be shown that in case of deposition temperatures of 300-700 °C a two-phase region exists in the metastable TiN-AlN phase diagram, which expands with increasing temperature, wheras at 100 °C substrate temperature no two-phase region was observed. But in opposition to the phase diagram known from literature, which is based on thermodynamic estimations, the detected two-phase region is narrow for typical PVD temperatures, thus allowing the deposition of cubic single-phase Al-rich (Ti,Al)N hardcoatings for tribological applications. Based on these results, a new Ti1-xAlxN film with x = 0.62 has been developed, which showed an increase of oxidation resistance by a factor of 4."

Jan 1, 1998

The current methodology to design stope support systems in South African gold and platinum mines is based upon the tributary area concept. The discontinuous nature of the hangingwall rock is not adequately addressed, and mechanisms leading to rock mass failures between adjacent support units are poorly understood. The work reported here aims to formulate a basis for quantifying support mechanisms and gain insights into the influence of rock discontinuities on stable hangingwall spans. Numerical models are used to qualitatively investigate the stress transfer from the support units to the discontinuous hangingwall. Stable hangingwall spans are quantified by considering two failure mechanisms, namely (i) beam buckling, and (ii) shear failure due to slip at the abutments. The output of the proposed design methodology is appropriate site specific support spacing, based on discontinuity spacing and orientation. The method is particularly suited to mines at intermediate and great depth, where typically the hangingwall is highly discontinuous due to face parallel mining induced fractures. Results of parametric studies show that with increasing in situ compressive hangingwall stress, beam thickness and friction angle, hangingwall stability is increased, leading to wider stable hangingwall spans between adjacent support units.

Jan 1, 2000

By Douglas Anderson

Even though there is always a feeling of anticipation before a blast is detonated, most blasts are part of a day’s work. Once in a while there is an event that impresses even the most jaded blaster. Few blasts have had the impact of the Kingdome implosion in March of this year. Fortunately for both the Seattle area and the explosives community, the “impact” of the implosion was far less than many local residents had feared. This outcome, of course, was not by chance, but the result of careful planning and design. An urban implosion requires a mix of engineering, logistics, and public relations. Unique challenges on this project tested the resourcefulness of the entire team.

Jan 1, 2001

By D. S. Saxena, Jack K. Tuttle

Lack of understanding of useful applications of explosives on construction work stem primarily from the fact that explosion is commonly associated with destruction. On rock excavation and other construction works a certain quantity of explosive is harnessed to perform useful work at the source e.g. blasts to disintegrate rock. Development in rock blasting techniques, including the use of multiple-row blasting with short delay ignition, have made it impossible to excavate rocks close to or below buildings even in closely built-up areas. To permit the use of explosives on construction projects, in ways that will not damage existing structures, guidelines have been developed from careful measurements of intensity of ground vibrations. Accurate electronic instruments are now available for doing this. PLANNING AND CONTROL Blasting operations must be carefully planned and carried out to avoid discomfort to persons or damage to property. This increase in the use of rock blasting in city areas alone has led to a number of problems due to ground vibrations, air shock waves, and the psychological effect of noise. While the latter seldom if ever causes damage, it does create irritation and discomfort to persons living or working near the blasting sites. A result of this is a steady increase in the number of complaints in respect of damage to houses and other premises. Many such complaints are genuine and damage may undoubtedly be caused when incorrect blasting techniques are used.

Jan 1, 1997

By José J. Suárez

As pressure grows for commodity pricing, new mines are more difficult to develop, the stock markets demand better financial returns from mining companies, resources for the developing and operations are scarce, and developing countries in Asia, and Africa demand more metals, it is important that mining companies effect better utilization of capital to develop capital projects. In the last few years, the costs for Capital projects have been impacted by the following factors:

May 1, 2013

By G. Arpa

Ventilation survey using tracer gas measurement is one of the techniques for mine ventilation design, monitoring and investigation of movement of fresh air and contaminants. However, there has been little research into using both tracer gas monitoring and numerical simulation. In this research, tracer gas technique was used for quantitative assessment of airflows through narrow vein shrinkage stopes with various opening shapes and friction factors. SF6 was used as a tracer gas to monitor airflow through three narrow vein shrinkage stopes in order to obtain diffusion concentration curves against elapsed time. The mine ventilation simulator, MIVENA Ver.6, was used to construct the entire ventilation network of the mine to monitor airflows through the stopes. The diffusion concentration curves against elapsed time were simulated with a numerical model. The result shows that the concentration-time curve is unsymmetrical and is skewed to the front of the flow direction. From the results of history-matching between the measured and the simulated curves, volume flow rates of airways and stopes were evaluated. Importantly, the tailing effect of the concentration-time curve between the measured and simulated is greatly improved by reconstructing an equivalent airflow route to represent unused mine openings, dead end drives and other open spaces. Finally, it can be concluded that openings, dead end drives and other open spaces have no relation on flow rates, but affect the airflow quality provided from the inlet portal as shown by tracer gas diffusion characteristics.

Jan 1, 2009

By J. G. Pippenger

The mining industry has been Australia?s major economic driver over the past decade, contributing 8% to Australia?s Gross Domestic Product and 26% of Australian Stock Exchange Market capitalisation. Australia is the world's leading exporter in coal, iron ore, alumina, lead and zinc; and second largest in gold and uranium. While driving the economy, this resource boom has also created a demand for professional and operating talent that has far outstripped the capacity of Australia?s 21 million residents. I moved to Australia some 10 years ago and have not looked back. This unique island continent with its mix of Indigenous and diverse immigrants ? many still proud of their convict ancestry ? has offered life long memories both professionally and personally.

Jan 1, 2011

By T Haskell, Y Joe, S Dickie

A current trend amongst producers is the increase in dewatering of iron ore fines (<0.5 mm), due to an increase in wet beneficiation processes used to upgrade lower quality ore deposits, increased water content in orebodies located below the water table, and increasing focus on transportable moisture limits (TML). Vacuum filtration is commonly used for dewatering of iron ore fines, and as with all filtration processes performance decreases with particle size. Significant improvements are possible with the use of filter aids, usually anionic surfactants and flocculants. Anionic surfactants reduce the surface tension of the associated water, which is then removed more readily leading to improved filtercake moistures. Anionic flocculants used correctly can improve cake permeability, in turn, decreasing cake formation times and increasing filtration rates. In addition to increased throughput, savings and benefits for producers can include: moisture limit penalties, improved handleability, along with energy and water savings.The effect of filter aids on two iron ore fines samples from the Pilbara region were evaluated using a lab scale vacuum filtration unit. The first sample showed a reduction in the filtercake moisture content by 2.3 per cent weight/weight (w/w) with the use of BASF’s Drimax® 1234. For the second sample a reduction in the filtercake moisture of 3.4 per cent w/w along with an increase in filtration rate of 20 per cent was achieved by using a combination of Magnafloc® 5250 and Drimax® 1239 NF, as both filter throughput and cake moisture were considered important by site.CITATION:Haskell, T, Dickie, S and Joe, Y, 2017. The use of filter aids on iron ore fines, in Proceedings Iron Ore 2017, pp 183–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Rodrigo Jerez

Advances in inexpensive computer automation led to the development and use of a computerized ore control system at the Cyprus Copperstone Gold Mine near Parker, AZ. These new ore control practices improved accuracy, performance and productivity of the ore control effort. An automated system for data collection, including bar coding of blasthole samples, laboratory analysis, data management, grade estimation, cut delineation and ore zone stake out, plays a major role in ore control practices. This is of particular interest because of the large amount of blasthole information being processed, analyzed and reported daily. Copperstone Gold management has been progressive toward new, efficient methods regarding ore reserve estimation, long-term mine planning, short-term mine planning, ore control and surveying. Technological advances, including powerful personal computers, applicable mine planning software and surveying instrumentation, have become readily available and affordable. The computerized ore control procedures used at Copperstone include sample data collection, laboratory automation and computerized data management. These have reduced the time to complete ore control on a blast pattern by 50% to 75%. The final product - ore control - is generated in a more timely and accurate manner.

Jan 1, 1991

By Louis Moyd

The Concrete Research Division, U.S. Corps of Engineers, has developed a simple procedure for determining the coefficients of linear thermal expansion of rocks by means of resistance wire (SR-4) strain gauges. Gauges are cemented to the surfaces of specimens, which are then brought alternately to temperatures of 35OF and 1350F. Results are accurate to the seventh decimal place. IN the course of investigations of the thermal properties of various rocks proposed for use as aggregates in concrete structures, a relatively rapid method of determining coefficients of linear thermal expansion was required. A method which proved to be satisfactory for this purpose was developed in the petrographic laboratory of the Concrete Research Division, U.S. Corps of Engineers, at Clinton, Miss. The method is based on the fact that strain effects in a specimen can be determined by measuring variations in the resistance of an electrical conductor firmly cemented to the surface of the specimen. Equipment for the determination of strain, electrically, has been developed by the Baldwin-South-wark Division of the Baldwin Locomotive Works in Philadelphia. This equipment includes small strain gauges made of coils of resistance wire bonded between thin sheets of paper (SR-4 gauges), and a portable "Strain Indicator" which records variations in the length of the gauges in microinches per inch. Gauges of this type are now in general use for determinations of various mechanically-induced strains, but their use for the determination of coefficients of thermal expansion appears to be a new application. The advantages of the method are that the test specimens may be relatively small and require only a minor amount of preparation, that a large number of tests can be run at the same time, and that the installation and operation of the equipment is relatively simple. The method and equipment described are now in regular use for determining the coefficients of linear thermal expansion of rock samples submitted to this laboratory. Rocks which have been tested include granites, syenites, gabbros, and other igneous rocks, limestones and dolomitic limestones, sandstones, and quartzites. Specimen Preparation: To standardize the conditions of the tests, the rock specimens are sliced by diamond saw into slabs about 11/2x11/4 in. In the case of bedded or foliated rocks, three oriented slabs are cut from the same specimen, and represent, respectively, a direction in a plane of the bedding or foliation of the rock; a direction along the bedding or foliation and at a right angle to the first; and a direction across the planes of bedding or foliation. One of the large surfaces of each slab is lapped for a few minutes with No. 100 abrasive powder to remove saw scars and irregularities. The slabs are soaked in petroleum ether and then dried in an oven to remove all traces of oil picked up in the sawing

Jan 1, 1951

By Louis Moyd

The Concrete Research Division, U.S. Corps of Engineers, has developed a simple procedure for determining the coefficients of linear thermal expansion of rocks by means of resistance wire (SR-4) strain gauges. Gauges are cemented to the surfaces of specimens, which are then brought alternately to temperatures of 35OF and 1350F. Results are accurate to the seventh decimal place. IN the course of investigations of the thermal properties of various rocks proposed for use as aggregates in concrete structures, a relatively rapid method of determining coefficients of linear thermal expansion was required. A method which proved to be satisfactory for this purpose was developed in the petrographic laboratory of the Concrete Research Division, U.S. Corps of Engineers, at Clinton, Miss. The method is based on the fact that strain effects in a specimen can be determined by measuring variations in the resistance of an electrical conductor firmly cemented to the surface of the specimen. Equipment for the determination of strain, electrically, has been developed by the Baldwin-South-wark Division of the Baldwin Locomotive Works in Philadelphia. This equipment includes small strain gauges made of coils of resistance wire bonded between thin sheets of paper (SR-4 gauges), and a portable "Strain Indicator" which records variations in the length of the gauges in microinches per inch. Gauges of this type are now in general use for determinations of various mechanically-induced strains, but their use for the determination of coefficients of thermal expansion appears to be a new application. The advantages of the method are that the test specimens may be relatively small and require only a minor amount of preparation, that a large number of tests can be run at the same time, and that the installation and operation of the equipment is relatively simple. The method and equipment described are now in regular use for determining the coefficients of linear thermal expansion of rock samples submitted to this laboratory. Rocks which have been tested include granites, syenites, gabbros, and other igneous rocks, limestones and dolomitic limestones, sandstones, and quartzites. Specimen Preparation: To standardize the conditions of the tests, the rock specimens are sliced by diamond saw into slabs about 11/2x11/4 in. In the case of bedded or foliated rocks, three oriented slabs are cut from the same specimen, and represent, respectively, a direction in a plane of the bedding or foliation of the rock; a direction along the bedding or foliation and at a right angle to the first; and a direction across the planes of bedding or foliation. One of the large surfaces of each slab is lapped for a few minutes with No. 100 abrasive powder to remove saw scars and irregularities. The slabs are soaked in petroleum ether and then dried in an oven to remove all traces of oil picked up in the sawing

Jan 1, 1951

By F. M. Van Tuyl

The oil industry had its inception in the United States in 1859 when the first oil well was drilled by Col. Drake at Titusville, Pennsylvania. From, a production of 2000 barrels for that year there was a slow but steady increase, with some fluctuations, up to 1901 for which year the output was approximately 69,389,194 barrels. Since that time the production has increased with leaps and bounds due to the rapid rise of the automotive industry, the widening use of oil as a fuel under boilers and the development of the. Diesel engine. The production for 1921 is estimated to have been 469,639,000 barrels. During the same year more than 125 millions of barrels were imported from Mexico. The oil industry, including the production, transportation, refining and distribution of petroleum and its products, is now the third largest in the country. Present Condition of the Industry During and immediately after the war the demand for petroleum exceeded the domestic production plus the imports from Mexico with the result that our storage oil was heavily drawn upon. Prices for crude exceeded all previous levels in the history of the industry. Pennsylvania crude sold for $6.10 per barrel and Mid-Continent crude for $3.50. Such prices stimulated wildcatting greatly with the result that several important new oil pools were discovered. Then as production increased the depression came which caused a large falling off in consumption. Pennsylvania crude fell to $2.25 per barrel and Mid-Continent to $1.00. Large oil companies such as the Standard, Sinclair and Empire took advantage of the situation, erected additional storage tanks and bought up millions of barrels to hold until better prices returned. Prices have already improved owing to a better market, but the domestic production coupled with the Mexican importations is still in excess of the demand with the result that the surplus is being stored. At the close of the year 1921, the U. S. Geological Survey estimates that there were 183,890,000 barrels of crude in storage in this country, the largest stocks in the history of the industry, yet an amount sufficient to supply the country for only 119 days at the present rate of consumption. Price reductions are again anticipated in some quarters but in view of the probable falling off in the Mexican output in the near, future due to the rapid rate of exhaustion of several of the most important pools and in view of the expected increase in consumption of gasoline and kerosene during the spring and summer months it is more likely that the present price level will be maintained. Present Sources of Domestic Supply Seven major oil fields are recognized by the U. S. Geological Survey in the United States. These are the Appalachian, Lima-Indiana, Illinois, Mid-Continent, Gulf Coast, Rocky Mountain and California. Two of these, Mid-Continent and California, supply about seventy-five per cent of the present total domestic output

Jan 1, 1922

By Thomas V. Falkie

The purpose of this work was to investigate the rate at which coal is delivered from the underground working face by gathering arm type loaders as employed on continuous mining machines, to identify the factors -- geometrical, geological, mechanical, or procedural which affect the delivery rate, and to develop quantitative rate descriptive equations for the loading function. The mathematical techniques employed were factor analysis and multiple linear regression. It was determined that the coal-cutting function of the continuous mining machine is the factor that primarily influences the loading function. The geometrical factors -- the dimensions of the work area in relation to the dimensions of the mining machine - were the factors of secondary influence. Fifty-five percent of the experimental variation in the loading function was explained in terms of the six most prominent independent variables. It is expected that this work will be useful in operations-research studies as applied to underground coal mining, and with refinement will enable mine planners to select equipment based on the operating characteristics of the equipment and the mining conditions.

Jan 1, 1972

By Orr C. W

Continuing the systematic investigation of the influence of elements on the properties of lead(1). If the effects of additions of copper (up to 0.3%) on Port Pirie lead have now been determined in so far as creep rate is concerned.The results in the present paper contain also a survey of the influence of copper on the micro-structure of lead, a feature which has not appeared in the previous papers of this series. Further, it has now become known that creep is but little related to the more usually determined properties such as hardness and tensile strength. Since, however, these properties are of considerable importance in connection with the fabrication and use of this metal. Brinell hardness determinations have also been made and are here included.It is becoming more and more realised also that to be useful, creep data should refer to stresses of the order of those used in practice. This is due to the fact that as soon as deformation takes place, the properties of the metal are automatically changed. Lead does, of course, creep during industrial use, and probably (in lead chamber construction for example) extensions of the order of 5%...

Jan 1, 1938

By I. Jackman

"Gold is present in different forms and associations in different ores. Flotation is used to recover gold and minerals associated with gold, but the applicability and type of flotation vary. The purpose of flotation in a gold recovery plant is largely dependent on the mineralogical association of the gold, and environmental and economic considerations. In this paper, the role of flotation in the recovery of gold is reviewed. The paper will describe examples of gold recovery by flotation including flotation of native gold, gold associated with sulphides including specifically copper sulphides, gold associated with tellurides, gold ores containing carbonaceous material and gold contained in tailings.INTRODUCTIONFlotation is widely used in the recovery of gold. However, the objectives and the mode of application are quite variable dependent on the type of ore, the gold association(s), other metal values, marketing considerations and environmental requirements. In this paper, a range of different applications of flotation incorporated in the recovery of gold are discussed. The reasons for each particular application are outlined and metallurgical results are presented.The mineralogy of the ore and the gold associations are fundamental influences on gold recovery. The use of flotation to concentrate gold is dictated by the mineralogy of the ore and gold. The fundamental factors are mineral/gold size, liberation size, association of the gold and type of gangue minerals or other valuable minerals. Gold can exhibit a range of sizes in a host from relatively large size (+50 µ) to refractory size (1 µ and sub-micron size). Similarly, the gold can occur in a number of phases in the same host. For example, the gold was present as petzite (AgAu telluride), calaverite (AuTe2) and native gold in a gold telluride ore and each of these minerals was associated with the pyrite host.Understanding the gold mineralogy and association is important in establishing the correct process route. The gold mineralogy is established by good mineralogy, use of diagnostic tools such as diagnostic leaching and assay by size fraction analyses and basic metallurgical testwork."

Jan 1, 1995

By W. E. Stephens, A. J. Boyce, D. Lowry

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. An integration of S isotopic, fluid and mineralogical data for granitoid-related mineralisation showed that the porphyry systems had a predominantly subcrustal magma source, but the inner magma pulse of two-mica granite in the Fleet pluton was derived mainly from reduced sediments. The porphyry-style mineralisation formed from boiling fluids at high crustal levels, with a moderately saline fluid percolating down to the upper veins as they cooled but not penetrating the deeper Talnotry deposit. Veins in peripheral greywackes have a significant magmatic component but also incorporated CO2-rich components and metals released by dewatering of host sediments in response to granitoid intrusion. The low grade of regional metamorphism resulted in the significant fluid input from country rocks which led to the more exotic mineral compositions, especially where argillaceous sediments were involved

Jun 19, 1905

By Dennis A. Swyt

In current post-industrial America, U.S. manufacturing is undergoing major changes both in the technology of its production and in the size and composition of its workforce. At the same time that computers and robotics move the shop floor toward becoming the unmanned "factory of the future" [1], they increase the need within the overall production enterprise for new types of technicians and engineering professionals [2]. Based on previous works which examined, first, the evolution of the technology of manufacturing toward the flexibly-automated factory of the future and, second, the technical- professionalization of U.S. manufacturing sectors [1,3], this paper looks briefly at the workforce of the U.S. metals industry.

Jan 1, 1989