Search Documents

By Hiren J. Shah

The urban environment and geology create unique challenges for design and construction of deep foundations. The effect of these is prominently experienced in New York City. Three such project case histories are presented in this paper. The first project is a multi-use development. Relatively unusual glacial geology was observed at the site during the subsurface investigation phase. This played an important role in the selection of deep foundations as well as during construction. The design and construction aspects of the pile foundations, settlement estimates, a pile drive test program during design, piling equipment and production pile installation are discussed herein. A relatively smaller project is the second case history. A combination of drilled and driven deep foundations was employed in one area of the project due to its unique conditions. In another area of the project, an addition to a structure required the use of supplemental foundations to resist new additional loading. Tight space and load sharing with the existing foundations were important considerations in the design and construction. Finite element modeling of the existing and completed structure was performed which was an interesting aspect of the project. The third project case history involves a very large multi-billion dollar project in which various different types of deep foundation elements were used. The aspects requiring the use of such a variety of types and sizes of deep foundation elements included: geologic conditions, re-use of existing foundations, protection of adjacent infrastructure, construction staging, restricted space, loads, deep excavations, cost and schedule.

Jan 1, 2011

Electrochemical Behaviour of Massive Chaclopyrite Bioleached Electrodes in Presence of Acidithiobacillus ferrooxidans and Acidithiobacillus caldus In this work, the monitoring of bacterial and chemical dissolution of massive chaclopyrite was evaluated using cyclic voltammetry (CV); the mineral surface was examined using scanning electron microscopy (SEM) and the elements were examined by Energy Dispersive X-ray Analysis (EDAX). The electrolyte employed for the electrochemical tests was the medium used to bioleaching the electrodes (3.0 g/L (NH4)2+SO4, 0.5 g/L K2HPO4, 0.5 g/L MgSO4+7H2O and 0.1 g/L Ca(NO3)2).The results showed differences in voltagramms carried out by Acidithiobacillus ferrooxidans and Acidithiobacillus caldus: In bioleached electrodes tested in the presence of Acidithiobacillus ferrooxidans, the anodic and cathodic current signals were larger than with Acidithiobacillus caldus. The analysis of CV results allowed attributing the different peaks observed in both the direct and reverse potential scanning to the oxidation of chaclopyrite to a secondary copper mineral (bornite, chalcocite and covellite) and its reduction via different non stoichiometric copper sulphides intermediaries. Surface evidences were observed by SEM, and chemical elements evidences were also investigated by EDAX.

Sep 13, 2010

Although small scale mining is regarded by many as of historical value only, this kind of mining activity is still much more widespread than is usually assumed. It has been estimated that it produces as much as ten per cent of the global mineral output. More significantly this figure is often much higher for many of the developing countries of Africa, Asia and South America, signifying the relatively greater contribution of small scale mining to the economies of those countries. It is also noted that small scale mining has always been a feature of mineral production in New Zealand and Australia. An attempt is made to define small scale mining, and the factors determining the suitability of small scale mining operations are discussed. The state of the art in small scale mining is reviewed and the author endeavours to rationalise the important parameters which contribute to successful small scale mining operations and discusses how these parameters may be optimised. The benefits of small scale mining to the mining industry as a whole and to the community at large are outlined. The paper concludes by emphasising the necessity to maintain small scale mining and 'explores' its future 'prospects'.

Jan 1, 1990

By W. H. Somerton

Many oil-producing formations contain significant amounts of clay. Because of the large surface area and reactivity of such surfaces, the response of the formations to various recovery processes may be dominated by the reactions of fine-grained minerals, including clay minerals, in the formations. Thus, the success or failure of enhanced oil recovery (EOR) methods may be controlled to a large extent by the amount and nature of these minerals in the formations to which the methods are being applied. One of the deterrents to the successful application of chemical EOR methods is the loss of chemicals injected into the formation, to non-oil recovery processes. These chemical loss processes include adsorption onto mineral surfaces, chemical reactions with rock and fluids in the formations, possibly leading to precipitation and plugging of the formation, and trapping of chemicals in parts of the rock structure so that they become unavailable for displacing oil. Chemicals that may be injected include surfactants, polymers and caustic solutions which react with organic acids in the crude oil to produce surfactants in-situ. These losses are most pronounced in fine-grained reservoir rocks containing substantial amounts of clays.

Jan 1, 1984

By W. J. Kingwell

My comments and questions are addressed to Mr. Troughton. It seems to me that the tests were very well tailored to determine long term effects on performance of bearing piles as groundwater pressures rise in the London Basin. This rise is being simulated by means of a groundwater recharge system but it would be informative to have further details of the controls of conditions simulated. Ideally the porewater pressure in Standpipes 1, 2 and 3 should be the same throughout the test. Under test conditions are there not practical dif­ficulties? Recharge Well C2 is a lesser dis­tance from the pile than the other wells. Was the rate of recharge to C2 regulated to a lesser rate than the other three? In my experience the rate of acceptance usually varies from well to well. Under a common feed pressure were mea­sures taken to compensate for this? Since the problem does not only affect London, but also Liverpool, Nottingham, Birmingham and to a lesser extent, Manchester, I question whether an ideal procedure is being used. It is well known that rates of acceptance decrease with time and often recharge wells need to be flushed out at regular intervals. Other pro­cedures may need to be adopted to accurately simulate the effect of groundwater rise, if tests of longer duration are to be considered.

Jan 1, 1991

By Thomas M. Barczak, Dennis R. Dolinar, Gabriel S. Esterhuizen

Longwall mines typically use some form of standing support for secondary roof support in longwall tailgate entries. Although there have been several new support products developed for this application, there remains no universal design criteria to optimize the application of these support technologies. The requirement for optimization and proper support selection is to understand the degree of control that the support has on the ground behavior. The ground reaction curve and numerical modeling was used to evaluate the impact of standing support on ground behavior. LaModel was used to evaluate the impact of standing support on main roof and floor behavior and pillar yielding. The conclusion drawn from this study was that standing supports do not have sufficient capacity to control main roof or floor loading or prevent the resulting convergence of the tailgate entry. However, it is imperative that this “uncontrollable convergence” be considered in the support design to prevent premature failure of the support. A FLAC model was used to evaluate the near-seam roof and floor behavior in conjunction with the global vertical and horizontal stresses. The model suggests that standing roof supports can have some impact on the ground behavior as the elastic response of the rock is exceeded and rock structure deteriorates from the stress concentrations that develop around the tailgate opening. During this phase, the capacity and stiffness of the standing support can be critical to the stability of the opening, as eventually the rock mass will be transformed into a partially detached structure whose weight must be supported by the standing support. This work is part of a ground control program of research at the National Institute for Occupational Safety and Health (NIOSH) aimed at improving mine safety by reducing roof fall injuries and fatalities.

Newmont Gold's methods for deposit modeling vary, depending on geology, mining and processing methods, economic feasibility and availability of historical information. It is argued that successful modeling requires understanding these factors, knowing the strengths and weaknesses of the various modeling techniques and being flexible in selecting the appropriate methods. Newmont is one of the world's largest gold mining companies, with operations in the United States, Peru, Mexico, Indonesia and Uzbekistan. And it is active in exploration worldwide. At the end of 1996, Newmont declared a total reserve of 1.15 equity kt (37.1 million equity oz) of gold and 2.17 equity Mt (2.39 million st) of copper. The gold deposits managed by Newmont totaled 752 Mt (829 million st) of ore containing 1.28 kt (41.3 million oz) of gold averaging 1.71 g/t (0.05 oz/st). In addition, Newmont is developing a porphyry copper-gold deposit that totals 9.1 Gt (1 billion st) of ore containing 380 t (12.1 million oz) of gold and 4.82 Mt (5.32 million st) of copper. (In May 1997, Newmont Gold Co. merged with Santa Fe Pacific Gold Corp., thus increasing Newmont's reserves to 1.72 kt or 55.2 million oz of gold and 2.17 Mt or 2.39 million st of copper.)

Jan 1, 1998

By Jr. Arcand

Canadian Economy ? Getting Results ???? A stronger Canadian economy ???? National debt cut ???? Taxes reduced, tax-free savings account, support for manufacturing sector ???? Assisting with infrastructure Aboriginal issues affect all Canadians ???? Aboriginal prosperity is in everyone?s interest ???? Conditions for Aboriginal success include: - Indian residential school settlement - resolving outstanding specific claims

May 1, 2008

By O Kirtel, A A. Faizan

With the rapid increase and development of high-speed trains (HSTs), the problems such as train-induced ground vibration and its dynamic effects on nearby structures have become a major environmental concern in urban areas. Ground-born vibrations produced by high-speed trains pose a great challenge for engineers to build structures in such areas that is applicable for residents. In order to study the effect of train-induced ground vibration on nearby buildings, an advanced three-dimensional finite element model for train-induced ground vibrations has been developed using PLAXIS 3D Ultimate. The results of the in situ measurements which was previously carried out by the authors were used to validate the numerical model. The field test for ground vibration due to the passage of a high-speed train was carried out on the Istanbul-Ankara high-speed railway in Turkey with a train speed of 250 km/h. An in-depth analysis was achieved to investigate the effect of different soil properties on the train-induced ground vibrations by using the verified model. According to the result of the vibration analysis, the relative vibration response curves in all directions (x, y, z) for different soil conditions were obtained comparatively. The obtained results of the vibration analysis are discussed in order to figure out some useful conclusions.

Nov 29, 2022

By Michelle Stokes, Alexandra Miller, Campbell McKenzie

"The ancestral Ringarooma River in northeast Tasmania has transported alluvial tin and other heavy minerals from their onshore source of stanniferous Devonian granites downstream into what is now Ringarooma Bay. Previous exploration work has demonstrated the presence of potentially economic tin mineralisation within the palaeochannels and terraces associated with the submerged river.The offshore tin resource lies directly on the seabed or with less than 2 m of overburden, and within 5 - 50 m water depths in the wider bay area. The main river channel continues offshore for at least 13 km, with high tin grades found within the palaeochannel but also dispersed across the sea floor as a sheet wash, a result of Quaternary sea level change reworking the placer deposits. This drowned portion of the coastal plain contains a continuation of rich tin leads as low gradient anastomosing channels, and has been delineated by marine seismic and drilling activity since the 1960s. Tin grades in the Tertiary and Quaternary alluvial profiles vary from 50 - 300 g/m3, with the highest concentrations in the coarser basal horizons. A previous offshore explorer estimated a resource of 194 Mm3 at 150 - 250 g/m3.Kenex Ltd created 3D models of the paleochannels and the mineralisation with the aim of better constraining the resource estimate and identifying additional depositional areas. The modelling was undertaken with the input of geophysical data, bathymetry and geochemical sampling of the seabed surface and from historic offshore drill holes. A prospectivity model covering Ringarooma Bay was produced to target tin-bearing gravels. Predictive maps were created to represent various features of the offshore mineral system, including assessing gradient changes in palaeochannels and their sinuosity. The model identifies areas with higher potential for alluvial tin mineralisation and will be used to focus the exploration programme over tenements currently held by Kenex Ltd."

Sep 1, 2014

By Keith R. Vining

Solid fuel, usually coke or anthracite, is commonly added to ground iron ore fines in the pelletising process to reduce the amount of burner fuel required and the maximum firing temperature, while maintaining pellet strength and the productivity of the pelletising plant. However, the use of coke and coal contribute to the production of greenhouse gases (eg carbon dioxide) and are a source of NOx and SOx emissions. Utilising wood biomass / wood char is one methodology CSIRO Minerals is investigating as an alternative to coke and coal, as it is a renewable energy source that is very reactive, has a low ash content and the potential to reduce emissions of greenhouse gases from the iron and steel-making process. Previous work has established that charcoal can effectively replace coke in the sintering process (Lovel et al, 2005), and the following experimental work aims to demonstrate that it can also provide an adequate replacement for coke and coal in the pelletising process. The paper presents the results of an experimental testwork program comparing the behaviour of fired pellets containing traditional solid fuels and charcoal. The physical properties of the pellets are compared in terms of their compressive strength, tumble and abrasion indices and the reduction properties. A qualitative assessment of the pellet microstructures is also presented.

May 1, 2007

By L. Li

The backfilling of underground stopes is a common practice throughout the mining industry. The stresses imposed by the backfill on the surrounding rock mass need to be assessed because of their influence on ground stability and on the hydro-geochemical response of the fill material. There is, however, a complex interaction between the relatively soft backfill and the much stiffer adjacent rock mass. In recent years, the authors have presented results from investigations conducted on stress distributions (obtained numerically and analytically) in and around backfilled stopes with (sub)vertical walls. In this paper, the influence of stope inclination and of backfill properties is evaluated. Results indicate that, in general, the vertical and horizontal stresses in inclined stopes are close to, but somewhat smaller than the stresses in vertical stopes. Nonetheless, significant differences can be observed in some cases, especially for the vertical stress along the inclined central line and along the hanging wall. It is further shown that neglecting deformability in limit equilibrium analyses is an acceptable assumption. However, Poisson?s ratio and the dilatancy angle, usually neglected in limit equilibrium analyses, may have significant effect on the stress distribution. Results also confirm that the backfill strength parameters (cohesion and friction angle) are critical factors required to properly evaluate the stress distribution, at least within a certain range of parameter values.

May 1, 2007

By William C. Grady

The environmental and economic problem created by pyrite in coal are well documented. The removal of pyritic sulfur prior to, or during, utilization has been the object of considerable research, however, much of this research has proceeded without a proper knowledge of the microscopic occurrences of pyrite in coal. This paper investigates the forms, occurrences, and variations in the distribution of pyrite in major West Virginia coal scan. Twenty-nine samples from twenty-two major west Virginia coal scans were selected for this study (see Table I). The samples were selected so as to be representative of the major coal producing areas of the state. All samples, except five, were collected at active surface mines, as indicated in Table I, and all except one were channel samples. The time interval between sampling and preparation of polished microblocks varied from two months to two years, though most were prepared within three months of collection. Grinding, screen¬ing, and riffling of samples to obtain 250 grams of -20 mesh coal for microscopic analysis strictly followed ASTM procedure D2013-72.

Jan 1, 1976

By A. C. Richardson

TROUGHS or launders are probably the oldest machines used for ore. concentration, and their development was suggested no doubt by the natural segregation and stratification of materials that take place in the bed of a stream. Trough washers for coal cleaning were first used in France and Germany about one hundred years ago and have been used in some form or other ever since. The early launders were intermittent or batch machines, and only comparatively recent developments have made them continuous. The chief disadvantage of early launder systems as applied to coal has been that when a satisfactorily clean: coal was produced the loss of good coal in the refuse was excessive. Other disadvantages have been the large quantities of water and the great lengths of troughs necessary to treat moderate tonnages of feed. One of the most widely used types of trough washers is the Rheolaveur, which has been developed in the last 25 years. Fig. 1 shows a more or less standard arrangement for fine coal. In this there are four troughs placed one below the other and sloped a few degrees from the horizontal. Rheo-boxes or draws are provided at intervals in the bottom of the trough for the removal of material deposited from the stream. These draws are spaced substantial distances apart. Some of the rheo-boxes are provided with upward currents of water to modify the horizontal current stratifica-tion. In operation it is the function of the first two troughs to remove all refuse material and permit only clean coal to be discharged over the end. In order to accomplish this, large quantities of coal are drawn through the rheo-boxes. The third and. fourth troughs are used to recover the coal discharged through the boxes of the first two troughs as a middling product and to discharge a clean refuse. The middlings are returned to the first launder and are usually about equal to 40 per cent of the raw coal being fed to the launder.

Jan 1, 1938

By G. Coetzer

During galena flotation of Rosh Pinah milled material, metal ions and salts contents of various water resources (deionized, simulated circulated, lead concentrate thickener, lead tailing thickener and borehole) influenced mineral recoveries, upgrade ratios, selectivities, froth stability and flotation kinetics. The various water resources employed during galena flotation caused activation, depression or selectivity effects on minerals due to the presence of different ions in solution. Metal ions in these water resources were adsorbed by the ore, whilst ions associated with gangue minerals (dolomite and quartz) were released into the flotation pulp. Lead concentrate thickener water caused depression of sphalerite and pyrite, increased fast floating fractions for silver, copper minerals, sphalerite and quartz (unwanted), and improved slow floating rate selectivity against pyrite and sphalerite. Lead tailing thickener water enhanced sphalerite recovery during galena flotation (unwanted), and increased fast floating fractions of pyrite. Western borehole water did not affect galena recovery, but sphalerite and pyrite recoveries were unacceptably too high. Ions from copper, lead, and zinc salts tended to release high amounts of ions, such as calcium, magnesium, silicon, and manganese from gangue minerals (dolomite and quartz) during milling. During galena flotation, lead ions depressed sphalerite, pyrite and dolomite at a lead concentration of 400 ppm, but sphalerite was activated at a concentration of 800 ppm. Sphalerite was activated with copper ions (89% recovery, 2.09 upgrade ratio) and depressed with zinc ions (maximum recovery of 25%). This corresponds with findings in previous investigations. Dolomite and quartz were slightly activated with zinc ions. No evidence was found that lead and copper ions activated any gangue minerals during galena flotation. Keywords: galena, water resources, metal ions, activation, depression, selectivity.

Jan 1, 2003

By V. R. Bovino

In the early 80's, the cover of a major weekly magazine proclaimed the "Death of Mining." A few years ago, mining conventions, similar to this, around the country sported the theme, "The Survival of Mining." Today, the SME announces that "Mining is Alive." Being part of an industry that is simply alive is not very exciting. We can do better! Our challenge must be to flourish, blossom, maximize our potential and expand our horizons. The pace of rejuvenating this industry is still woefully inadequate. The new generation of mining industry leaders recognizes the urgent need for bold operational changes?changes in the way we deal with our employees? changes in the way we achieve productivity? and changes in the way we reward our employees for productivity.

Jan 1, 1991

By Dale S. Preece

"Detonation delay timing has been an important aspect of quality rock blasting for decades. Detonators that enable delay timing have improved over the years especially with the recent advent of precision electronic detonators. The positive effects of precision delay timing have been observed repeatedly in the field with improved fragmentation, heave and overall blast control. Three-dimensional computational capabilities in terms of software, material models and computer speed have recently made possible the computer simulation of multiple blast holes in a bench configuration with precise delay timing between holes. Some of the key physical phenomena enabled by precise delay timing include: 1) collision and interaction of stress waves produced by adjacent blast holes, 2) reinforcement of stress waves from multiple holes as they reflect from the bench face and ground surface, 3) reflection of stress waves from “dynamic free surfaces” created by previously detonating holes, and 4) deformation induced fracturing, cracking and fragmentation. Simulating rock blasting in 3D has shed light on the physics involved and is resulting in an evolution of our understanding of fragmentation mechanisms. Routine use of these 3D computational tools will result in a much better understanding of the complex physics set in motion by the rock blasting process and allow predictionof improved blasting."

Jan 1, 2009

By W. J. Wenger

THIRTY-FOUR analyses of crude oils from the fields of the Four Corners Area of Arizona, Colorado, New Mexico, and Utah are presented and compared. The samples, taken from formations in four geological time periods, have high gravity and low-sulfur, -nitrogen, and -asphalt content. Generally, the oils are paraffinic in the low-boiling fractions, with increasing naphthenicity in the higher-boiling fractions. Oils from Cretaceous formations resemble other Cretaceous oils in the Rocky Mountains, but oils from Permian and Pennsylvania formations are unlike other oils of these ages in the Rooky Mountains. The differences in the oils are minor and cannot be used to distinguish between fields or between producing formations. With minimum special processing, the oils should yield large amounts of good-quality motor fuels. INTRODUCTION The only place in the United States where four States have a common junction is known as the Four Corners Area. This area (fig. 1) includes the northeast corner of Arizona, the southwest corner of Colorado, the northwest corner of New Mexico, and the southeast corner of Utah. It includes three major geological basins: The Black Mesa, the San Juan, and the Paradox. Major oil developments have occurred in both the San Juan and Paradox basins, but no discovery of commercial importance has been made in the Black Mesa basin.

Jan 1, 1960

By J. Guha, D. Racicot, S. Peloquin, F. Lange-Brard, S. Bureau, A. Tremblay

The Devlin copper deposit consists of a flat-lying vein and a network of steeply dipping mineralized veinlets hosted by leucotonalite of the Chibougamau Pluton. Most of the vein is enclosed in a hydrothermal breccia zone which has been superimposed on a primary igneous breccia formed during the emplacement of the leucotonalite unit. This igneous breccia contains cognate fragments as well as fragments of the Dore Lake Complex, host rock to the pluton, set in a leucotonalite matrix. The hydrothermal breccia is formed of fragments of leucotonalite and the earlier breccia set in a matrix of finely comminuted rock variously altered in a roughly zonal arrangement. The major ore-bearing structure is the tabular flat-lying vein, varying in thickness from 10 centimetres to 1 metre, with a slight dip to the northeast. Well developed fracture planes, in four major orientations, contain both sulphides and gangue minerals. These appear to be displaced by the flat-lying vein. Late movements affecting the deposit include minor vertical displacements and an east-west shear truncating the southern edge of the vein. Widespread selective alteration of the leucotonalite, followed by multiple alteration veining stages characterize the deposit. Fluid inclusions associated with the mineralization indicate low temperatures, variable salinities with a variety of daughter minerals, and a vapour dominated phase. The fluid shows evidences of boiling at shallow depths. The sequence of events envisaged for the Devlin deposit is a primary brecciation during emplacement of the leucotonalite unit with widespread selective alteration possibly during the cooling stages followed by hydrothermal brecciation and late stage fract uring producing the vertical fractures and the flat-lying vein. From the alteration characteristics and the fluid data it is inferred that the Devlin deposit is the near-surface expression of a porphyry system.

Jan 1, 1984

By W. E. Lee

Penetration and dissolution mechanisms are reviewed for predominantly single-phase oxide, two phase oxide and oxide-carbon composite refractories by liquid silicate slags. Theoretical models of these processes, as well as static (sessile drop, dipping and crucible) and dynamic (rotating finger and rotary slag) experimental tests, along with their practical limitations are considered. Direct (congruent or homogeneous) attack is controlled by the reaction rate at the slag-refractory interface or the rate of diffusive transport of species to it through the slag leading to active corrosion. Indirect (incongruent or heterogeneous) attack is controlled by diffusive transport through the slag or through a new solid phase, which forms at the original slag-refractory interface. This may lead to passive corrosion. Examples of direct and indirect attack in a range of refractory/slag systems are described highlighting the critical influence of the composition and hence viscosity of the local liquid slag adjacent the solid refractory. Penetration and corrosion can be controlled either through the local slag composition via the refractory or the bulk slag or by microstructural control of the refractory by e.g. internal generation of dense layers or external deposition/generation of passive coatings, so-called in situ refractories.

Jan 1, 2004