Search Documents

By Ginger Gibson

As an occupational culture, mining comes with its own set of rules, agendas and values. Yet mines often also operate in the traditional territories of indigenous communities, with whom specific agreements are negotiated that commit to respect culture, economy and environment. Mines in these locations employ extremely diverse workforces whose value systems often come into conflict in on-the-job relationships. Adaptation of individual worker attitudes and industrial operating culture thus both need to occur if there is to be the negotiation of a workable relationship. This paper will discuss ways that NWT diamond mines have adapted to their workforce, to ensure that rights and cultures of their diverse workforce can be respected. Historically, the concept of culture has been dealt with solely through the forum of ?cross-cultural? workshops. Gibson presents a model of a new type of ?cultural-engagement? workshop based on the top ten cross-cultural conflicts that actually arise at a remote mine-site. This model helps managers, team leaders, and workers to tackle in-mine conflicts that arise based on differing value systems of aboriginal and non-aboriginal workers and management. In addition, Gibson suggests that the concept of culture must be more rigorously applied throughout the mine structure and not discussed only in the forum of the cross-cultural workshop.

May 1, 2007

By Stoyan Gaydardzhiev, Michel Shengo, Pierre Kalenga

Lab-scale flotation of copper and cobalt oxidized ore from the Luiswishi deposit in the Katanga province (DRC) has been done focusing on the influence of the degree of process water recycling on metals recovery. Results have shown that at 20 % recycling rate, the recovery of copper and cobalt in the cleaner stage have been respectively reduced to 23 % and 45 % in comparison to 53 % Cu and 63 % Co if process water has not been recycled. At 10 % recycling rate however, the system could still tolerate the effect from recycling, since Cu and Co recovery has remained respectively at acceptable levels of 52 % and 60 %. In order to explain the reasons for the observed worsening of flotation results if process water was recycled at rate higher than 20 %, electrochemical investigation of the pulp has been performed. It has been established that the chemical compounds formed in the pulp when process water was recycled, do influence the sulphidization of malachite and heterogenite and impact further collector adsorption. To confirm these assumptions, the effect from thiosulphate ions presence during the sulphidization of high purity malachite has been studied. It has been found, that thiosulphate ions depending on their concentration in water induce variations in pulp properties such as DO content, pH, Es and contribute to formation of undesirable chemical compounds on mineral surface as identified by DRIFT spectroscopy.

Jan 1, 2014

By Arnulf P. Hagen

This project was designed to explore the suitability of using fluorinated inorganic materials as solvents for the in situ mining of thin seamed, heavily overburdened coal; to build a data base for the selection of an inorganic solvent for use for coal cleaning; to determine if fluorinated solvents will reduce the organic and inorganic sulfur contents of the coal, as well as to lower the ash content. The coal samples have been combined with pure solvent, as well as with aqueous solutions at atmospheric pressure and at increased pressure. The increased pressure experiments are important since they duplicate the conditions anticipated for an in situ cleaning and mining operation. Trifluoroacetic, difluorphosphoric (phosphorodifluoroidic), and trifluoromethanesulfonic acids have been found to be effective for the cleaning of high sulfur, high ash coal at 300°C and at atmospheric pressure. At pressures up to 20,000 psi the effectiveness of these reagents is not decreased.

Jan 1, 1983

By D. B. Lovett

The work described in this report was directed toward identifying and devising methods to minimize the previously observed variability between working level hour exposures and the alpha particle track densities resulting on Track Etch films exposed to mine atmospheres containing radon and radon daughters. The disequilibrium between radon and its daughters was shown to directly affect this Track Etch film calibration factor. The wide range of disequilibrium states possible in mine situations amply explains the variability in the previous tests. A file of published mine atmosphere composition data was compiled and was used, along with atmospheric compositions derived from several theoretical models ref the atmospheric behavior, to evaluate the variability of several dosimeter configurations and concepts. A nonlinear, iterative regression analyse; was formulated that successfully predicted working levels to within 8 to 10% from only the alpha particle activities (Rn, RA, and RaC') data such as are obtainable from Track Etch films over a wide range of disequrlibrium conditions. A model expressing atmospheric concentrations as a function of radon source strength, plate out rate factor, ventilation rate and the fractional re-entry by recoil of previously platted-out daughters was derived and used in the regression program in addition to preparing a set of reference tables and graphs showing the disequilibrium behavior of the atmosphere. Other factors that can affect the Track Etch Film response writ considered and shown to he less crutial than the disequilibrium state. The results of a series of exposures of a dosimeter concept fixture in the Denver Mining Research Center radon chamber air presented and discussed.

Jan 1, 1976

By Harold H. Goe, Louis V. Bender

The recovery of arsenic was started at the Washoe Reduction Works (later called the Anaconda Reduction Works) in 1904, when an arsenic plant was constructed adjacent to the lower end of the 60-ft. main flue.' This plant originally consisted of a Brunton roasting furnace for treatment of flue dust and a small reverberatory furnace for treating the crude arsenic produced in the roasting operations, together with the necessary kitchens for condensation of the fumes and grinding and barreling apparatus for preparing the refined white arsenic for market. The Brunton furnace was fired with wood. It was 14 ft. 6 in. in diameter with two outside fireboxes. The hearth revolved upon a central shaft. The charge was fed through a dust-tight hopper on to the center of the hearth and slowly moved to the outer edge of three rows of stationary rabbles fastened in the roof of the furnace. There was a 3-ft. space between the hearth and roof. A crude arsenic was condensed from this furnace. The hot flame from the fireboxes passed directly over the charge, vaporizing the As203 that was carried through brick flues to the condensing chamber. This chamber was 8 ft. high, 16 ft. wide and 240 ft. long, divided into small kitchens by partitions spaced every 7 ft. It was connected with the main flue system to provide draft and to receive any losses from the chamber. The small kitchens were connected by openings in such a way that the fumes took a zigzag course, causing them to come in contact with the cold walls and ceiling and condense the arsenic. There was an opening from the outside into each kitchen, for the removal of the deposited arsenic, which was closed by a wooden door. The refining furnace was a small coke-fired reverberatory having a hearth 10 by 20 ft. in dimensions. It had three hoppers through which the crude charge was introduced, and one firebox placed at one end. The hot gas from the burning coke passed over the charge, volatilizing the arsenic and carrying it to the kitchens.

Jan 1, 1934

By H. L. Luo, P. Duwez, C. C. Chao

BY rapidly cooling alloys from the liquid state, it is possible to obtain solid solutions beyond the equilibrium concentrations, provided that the components are miscible in the liquid state. Typical such cases include CU-Ag,1 Pt-Ag,2 CU-Rh,3 nickel-base alloys with silicon, germanium, and tin,4 and cobalt-base alloys with silicon, germanium, tin, aluminum, and gallium.5 In the present note it is shown that terminal solid solutions can be appreciably extended in A1-Mg alloys. The alloys whose compositions are given in Table I were prepared by induction melting in tantalum crucibles under an argon atmosphere. Both aluminum and magnesium were 99.99 pct pure. Weight losses after melting were less than 0.2 pct for the aluminum-rich alloys and less than 0.4 pct for the magnesium-rich alloys. From these weight losses it was estimated that the compositions of the ingots after melting were accurate within 0.3 at. pct for aluminum-rich alloys and within 0.5 at. pct for magnesium-rich alloys. As indicated in Table I, the compound AuCd10 in which there is an ionic contribution to the bonding. The authors thank Dr. J. H. Westbrook of the Research Laboratory, General Electric Co., for arranging the supply of materials and for his interest. This investigation was supported by the U.S. Atomic Energy Commission under Contract AT(30-1)-1002, Scope I. some of the alloys were also chemically analyzed and the results confirmed the limits of uncertainty based on weight losses. Rapid quenching from the liquid state was achieved by techniques previously described.8,7 The principle of these techniques consists of propelling a small globule of liquid alloy (about 20 mg) onto a copper substrate. The thin foils easily detached from the copper substrate were analyzed by X-ray diffraction using a Debye-Scherrer camera 114.6 mm in diameter and either nickel-filtered copper Ka or iron-filtered cobalt Ka radiation. Since the back-reflection doublets were resolved, the wavelengths used in the computatioas were CuKal = 1.54050A and CoKa1= 1.78892A. Lattice parameters were obtained by extrapolation of the Nelson-Riley function, and the tables compiled

Jan 1, 1964

By T. R. Achenbach

1. This, the final report to the U. S. Bureau of Mines on the program with the subject title, presents the data obtained from June 29, 1973, to April 20, 1974. 2. Operating in the Illinois #6 coal seam, the effectiveness of foam opposed to water was compared in reducing respirable coal dust. A combination of 39 foam generators and 14 water sprays were used during the foam tests. Sixty one water sprays were operated during the water tests. Data from 24 shifts using foam and 21 shifts using water are presented. 3. Additional work on foam generator design should be undertaken to provide coverage to a wider area with foam. 4. The general attitude of those working on the foam program and with the miner at the face was positive. It is urged that the work be continued. 5. The minor respiratory irritations evidently caused by an aerosol effect of the surfactant should be investigated. 6. The statistical analysis of the tests will be made and reported by the U. S. Bureau of Mines.

Jan 1, 1974

By Charles H. Jacoby

During the past three decades an ever increasing number of uses for underground storage space has been developed. In some instances, the value of the space created has been so great that the host rock has been wasted. The preferential use of salt to host underground cavities is based on numerous factors, the primary two being low extraction costs and low permeability. Both dry and solution mined cavities have been created for the storage of a variety of materials. As the demand for underground storage and disposal grows, so must our selectivity of the materials to be stored.

Jan 1, 1985

By Werner Unland, Nick Holl

"The paper presents the engineering design and experience gained so far with a dewatering system for an open-pit uranium mine planned at Key Lake in Northern Saskatchewan.The results of hydrogeological investigations preceding engineering exhibit an extensive unconfined overburden aquifer hydraulically connected with the underlying Athabasca Formation and basement rocks, both of relatively low hydraulic conductivity. The overburden aquifer is embedded in a bedrock trough, with the deepest depression between the planned pits. The hydrogeological data were used in a numerical dewatering model simulating groundwater flow atdifferent stages of the pit development.Based on the model results, the engineering design had to provide for different pumping rates, varying between 1.0 and 0.21 ms/sec. This problem was solved by using a double line pressure system. The design concept for the complete peripheral discharge system and the well design used for 26dewatering wells are discussed.Experience with reverse-circulation techniques applied for the construction of the dewatering wells is presented. Theoretical and practical considerations which led to the constructionof wells of different diameters are discussed.The design of the in-pit dewatering system provides for seepage ditches, horizontal drains, pit-bottom sumps and inpit dewatering wells where required."

Jan 1, 1980

By T. D. Guldem, J. L. Kaae

ALLOYS with nominal composition of 45-Fe 35-Ni 20-Cr, ASTM-B-163, known under the commercial names of Incoloy 800 and Sanicro 31 (Alloy 800), are often employed at elevated temperatures for extended periods. Therefore, knowledge of the aging behavior of these alloys is of considerable importance. Significant decreases in ductility and increases in yield strength have been observed in the 45-Fe 35-Ni 20-Cr alloys containing about 0.4 pct Ti and 0.4 pct A1 after long-term aging at 540" to 700"~."~ However, no direct evidence has been presented for precipitation phenomena that might result in such changes. Strengthening effects have been attributed to the effects of local or-dering.3 Since y' precipitation (Ni3A1, Ti) is known to occur in similar alloys which contain more titanium and aluminum,4-7 it was decided to explore the possibility that y' might precipitate in these alloys and might be responsible for the changes in mechanical properties on aging. This note reports some observations of two distict types of matrix precipitates made by means of transmission electron microscopy, in a 45-Fe 35-Ni 20-Cr alloy containing 0.31 pct Ti and 0.4 pct Al. The steel used in this investigation was obtained from the Sand-vik Steel Works; it is designated Sanicro-31 (Alloy 800). The chemical composition of the alloy is given in Table I. Aging of solution-treated material at 700" and 800°C for 130 and 100 hr, respectively, produced the matrix precipitates shown in Figs. l(a) and l(b). It is apparent from these micrographs that the precipitate particles occurred in the form of thin square plates parallel to the matrix cube planes. Extraction replication and selected-area electron diffraction showed that the precipitates were M23C6. Coherency strains, consistent with the semicoherent nature of small M23C6 precipitates,' were evident for certain imaging conditions. In addition to matrix precipitation, preferential precipitation of M23C6 on dislocations was common, as has been reported previously for austenitic stainless steels.'" Specimens aged for longer times (-300 hr) at 700°C exhibited a different type of coherent matrix precipitate in addition to the M23C6. An example is shown in Figs. 2(a) and 2(b). In addition to the few large M23C6 precipitates, small precipitates exhibiting strain contrastl0,ll are present. The "line of no contrast" of the strain field of a given precipitate lies along differ-

Jan 1, 1970

Real time analysis of ore quality between the mine and mill provides major benefits to copper mining and processing operations. Prompt gamma neutron activation analysis (PGNAA) is a proven technique that has been successfully applied for real time conveyed flow multi-elemental measurement. The advantage of PGNAA is that it measures through the full conveyed cross section continuously and provides representative element measurement without the need to constantly sample coarse (primary crushed) conveyed flows. High specification PGNAA analyzers enable accurate measurement over time increments as short as thirty seconds. Elements such as copper can be measured to a precision of 0.02% copper which is sufficient for high confidence in decisions for bulk flow diversion. Increments of eight tonnes are being diverted through a bulk ore sorting application to remove batches of waste from mill feed as well as divert material to different stockpiles based on ore quality. Longer measurement increments of two to five minutes are suitable for blending control of ores to reduce feed quality variability and to control average ore quality within a target range. Feed blends can be adjusted as frequently as required but typically multiple measurement increments are composited to produce a rolling average ore quality. The paper details two case studies where analyzers have been successfully used to measure conveyed flows for blending and bulk diversion applications. The real time measurements of ore composition are also used for ore reconciliation, in metal accounting and providing process operators with advance warning of ore quality changes that may affect grinding performance and cause process upsets. Real time ore quality measurement has proven beneficial in improving copper processing performance through better utilising plant capacity in a leaching operation, optimising ore feed quality, and reducing unnecessary processing of waste. INTRODUCTION Representative real time elemental analysis of conveyed ore quality using fully penetrative technologies has been available to the minerals industry since the 1990s. The Prompt Gamma Neutron Activation Analysis (PGNAA) technique was developed into a conveyed material analyser and soon adopted by the cement and coal industries which recognised the benefits in real time quality management. These commodities were ideally suited to this measurement technique as operations generally involved conveying bulk material prior to processing. Measured quality was used to divert material to different destinations or used to control blending for improved quality consistency. Uptake in the minerals industry, however, has been slow until the last ten years, and particularly until the mid-2010s.

Jan 1, 2019

By Gerald H. Luttrell, Lance Christodoulou, Jaisen N. Kohmuench, Michael J. Mankosa

The efficiency of the froth flotation process has long been known to be strongly dependent on particle size. For sulfide minerals, good recoveries are typically achieved in industrial flotation circuits for particles in the 30 to 200 µm size range. Particles outside this critical size are typically lost in industrial operations and rejected to tailings streams due to inherent constraints associated with the physical interactions that occur in the pulp and froth phases of conventional flotation equipment. In response to these limitations, a series of experimental studies were conducted to determine whether particles previously lost as tailings could be economically recovered using a suite of novel flotation technologies developed for upgrading ultra-coarse and ultra-fine particles in the industrial minerals industry. For the case of ultracoarse particles, a fluidized-bed flotation system called the HydroFloatTM separator was tested. The data obtained using this novel flotation device in both laboratory- and pilot-scale trials showed that good recovery of previously lost sulfide values up to 850 µm diameter could be achieved. Similarly, for ultrafine particles, a high-intensity cavitation-based column cell was tested. This technology, which utilizes highshear contacting of slurry and gas, was capable of recovering valuable ultra-fine sulfide that were previously lost due to the low capture efficiency of conventional flotation processes. The objectives of this article are (i) to describe the unique operating principles of these two advanced flotation technologies and associated ancillary classification equipment, (ii) to present laboratory- and pilot-scale experimental test data showing the metallurgical benefits of the proposed novel flowsheet for sulfide tailings processing, and (iii) to provide a generic cost-benefit analysis of the proposed system for recovering lost values in existing sulfide tailing streams.

Jan 1, 2016

By R. F. Nielsen, R. G. Bentsen

Jan 1, 1966

By Matheus Sampaio Modesto de Paula

O presente trabalho mostra o desenvolvimento de um produto, até então não comercializado pela CSN/PR, criado para o aproveitamento da capacidade ociosa de seu laminador reversível a frio. Historicamente, a produção do laminador era direcionada exclusivamente para o abastecimento de uma linha de galvanização contínua, mas trabalhos bem sucedidos para o aumento da produtividade do laminador resultaram em capacidade excedente do equipamento. Diante desse cenário, a comercialização de bobinas Full Hard se tornou uma opção viável para a abertura de mercado e aumento de competitividade, frente a atual pressão imposta por produtos importados. Visitas aos potenciais clientes foram necessárias para o levantamento das características importantes a seus processos produtivos e adequação dos parâmetros utilizados no laminador reversível. Atualmente o produto está homologado e sendo fornecido a clientes externos, e espera-se o aumento da carteira, dependendo apenas da evolução do mercado.

Jul 30, 2018

By Alessandra Savazzini dos Reis

A crescente preocupação em relação às áreas de proteção ambiental e ao alto consumo de argila, matéria-prima da cerâmica vermelha, ocasiona a indisponibilização progressiva de reservas de argilas no Brasil. Com isso, vê-se a necessidade de incorporar resíduos na massa argilosa para confecção de produtos de cerâmica vermelha. A indústria de cerâmica vermelha brasileira consome cerca de 10 milhões de toneladas de argila ao mês para produção de telhas e blocos. Na própria olaria são gerados resíduos, tal como, o resíduo de massa cerâmica crua originado na etapa de conformação das peças. Este trabalho visa incorporar o resíduo de massa cerâmica crua na massa argilosa usada em cerâmica vermelha. O resíduo foi caracterizado por meio de ensaios de FRX, DRX, limites de Atterberg e distribuição de tamanho de partículas. Corpos de prova feitos com massa argilosa e resíduo em teores variando de 10% a 90% (massa) foram conformados, secos à 110ºC, queimados à 900ºC em forno industrial e submetidos a ensaios de absorção de água, porosidade aparente, massa específica aparente e resistência à compressão. Os resultados evidenciaram que as propriedades cerâmicas avaliadas nos corpos de prova da massa argilosa incorporada com o resíduo atendem aos valores das argilas-padrão brasileiras para cerâmica vermelha.

Aug 17, 2017

By Rafael Henrique Alves Gomes

A automação em processos industriais agrega qualidade, padronização e segurança aos produtos e pessoas envolvidas. Entretanto, as demandas de mercado, custos agregados e a concorrência exigem melhorias que podem ser alcançadas através de métodos de otimização. Este artigo apresenta algumas metodologias e ferramentas para otimização de processos industriais que visam desvincular a obrigatoriedade de que Técnicas de Controle Avançado em métodos de otimização são a única solução capaz de oferecer resultados satisfatórios para aumento de produtividade. Os recursos expostos abordam a gestão de malhas de controle, gestão de alarmes e o cálculo do indicador global de eficiência, o OEE.

Aug 17, 2017

By C. N. Bensley, S. K. Nicol, R. Lamb, G. W. Kidd

Flotation circuits in the metalliferous industry recover high value concentrates from very fine (minus 0.lmm), low grade, slow-floating feeds. Flotation columns acting as final cleaners within these circuits offer the benefits of higher grade concentrates, reduced circuit complexity, improved control and reduced power consumption. By contrast, in the coal industry, these benefits have not been realised, principally because columns are not well suited to the treatment of conventional coal flotation feeds (minus 0.5m). However, this does not imply that columns do not have a place within the coal industry, rather that they must be applied in a role where all the unique advantages of column flotation can be of benefit. The development of a commercial scale column to recover discarded ultrafines from the Riverside preparation plant of BHP-Utah Coal Limited is discussed. Particular emphasis is placed on the column design features pertinent to the recovery of ultrafine coal. Pilot and commercial scale column performances are compared. The results of the commercial scale testwork indicate that a full installation at the 5.5 MTPA Riverside plant would annually recover additional coal worth $US 6.6M.

Jan 1, 1988

By E. Topuz

The objective of mine ventilation is to provide suitable environmental conditions in working places at an economical cost. Maintaining a stable air flow, i.e., a flow quantity and the direction, is of vital importance. In practice, however, air flow quantity in underground openings varies continuously. Therefore, the stability of air flow means relative stability that is the flow in a branch moves along a certain direction while the variation in air quantity stays within acceptable limits. Many underground mines have low stability of mine air flow because almost all types of ventilation systems involve complex diagonal branches through which air flow quantity and, more importantly, the air flow direction may change easily. This creates extremely hazardous, unstable conditions, especially during emergencies. This paper deals with the directional stability of air flows in underground mines in single or multiple fan systems. It examines the rules of directional changes of air flows in diagonal branches, and proposes a method of calculating the stability conditions. It provides a criterion that may be used in designing new mine ventilation systems to ensure a desired degree of stability or in improving the existing systems.

Jan 1, 1986

By P Wahyono, H Vega, S Riza, P Vergara, P Gonzalez-Carbonell

PT Freeport Indonesia (PTFI), operating in the Ertsberg Mining District in the Province of Papua, is developing the Grasberg Block Cave copper-gold mine. The site aims to output 160 000 t/d and will be located underneath the current Grasberg Open Pit. Initial studies of the potential to develop a block cave mine in the Grasberg orebody have revealed that the mine will require significant volumes of air. The Grasberg Block Cave (GBC) project requires four primary fans (3750 kW each) to support production at full capacity.Fan #1 commissioning was accomplished successfully on 9 February 2012. However, Fan #2 chamber, which is separated by a 20 m pillar, had not been completed. The main challenge was Fan #2 chamber still needed to be benched. The risk of damage to the critical infrastructure in Fan #1 chamber, including ground support, cracks in pedestals, and misalignment in the impeller shaft were considered. The challenges were blasting the bench without damaging the surrounding infrastructure, completing the work safely and meeting the schedule. This was achieved with the engineering control methodology. This paper summarises the benching process of Fan #2 chamber and its impact upon Fan #1.CITATION:Vega, H, Riza, S, Gonzalez-Carbonell, P, Wahyono, P and Vergara, P, 2013. Excavating an underground primary fan chamber that is adjacent to a fully operational primary fan in PT Freeport Indonesia's Grasberg Block Cave Mine, in Proceedings The Australian Mine Ventilation Conference , pp 115-122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Charles E. Whieldon

Data on the oilfields in Mahoning, Columbiana, Carroll, Jefferson, and Harrison Counties, Ohio, were collected from scattered sources and compiled to make the information readily available to operators who may be interested in conducting secondary-recovery operations in the area. General geology, oil production, oil-productive acreage, core data, reservoir calculations by townships, and miscellaneous data and reference material are presented.

Jan 1, 1965