Search Documents

By W. J. Sharwood

Cupellation is well known to be one of the most effective methods of separating silver and gold from base metals and other impurities, as well as one of the most accurate means for their estimation. In the latter application it consists in absorbing in some porous medium the fused lead oxide formed by the oxidation of the lead "bath," which carries with it the oxides of other base metals present. It has long been recognized that small amounts of both silver and gold were removed and absorbed together with the base metals, as well as being to some slight extent volatilized, and in work of the highest accuracy a correction is made for the "cupellation loss." Thus in the assay of bullion this is done by means of "proofs" of like composition, which are manipulated throughout in precisely the same manner as the assay pieces, and are assumed to lose or gain like amounts. In the case of certain very rich ores and commercial products the loss is adjusted by assaying the cupel itself and recovering the precious metal absorbed, but this doubles the labor and does not remedy the loss by volatilization. Arbitrary tables have been drawn up by various authorities with the object of enabling a correction to be applied without the use of a check. These have been of very limited practical use owing to the fact that a number of factors affect the losses sustained. For a fixed amount of precious metal the loss varies with the amount of lead used, with the nature and amount of the impurities, with the porosity of the cupel, with the air supply, and above all with the temperature at which cupellation is carried on. Pure silver loses relatively much more than gold, but the loss in either is diminished by an addition of the other metal. The concentration of precious metal in the litharge increases as the concentration in the lead increases, but little work has been published connccting the two. If all other conditions remain the same the actual total loss increases, but the percentage loss diminishes, with an increase in the weight of precious metal treated. The results of an immense number of experiments have been published at various times- during the past hundred years giving the actual or the percentage losses suffered under various conditions of cupellation, but the data are widely scattered and few attempts have been made to correlate them, so that no definite law has heretofore been shown to exist

Jan 1, 1916

By Walter H. Bucher

THIS symposium is designed to lay the basis for a general discussion of the place of geophysics in the training of geologists. As there is danger that in the ensuing debate individual interests may be given emphasis out of proportion to their place, we shall do well to view the whole field of geological inquiry in order to see the problem in true perspective. THE NATURE OF GEOLOGICAL INQUIRY "Basic" and "Complex" Sciences It is convenient to divide all science into two major divisions, the basic and the complex sciences. The basic sciences separate out from reality such entities as "substances" and "movements," describe their behavior in terms of arbitrary units of measurement and derive from them by progressive abstractions concepts and patterns of behavior that exist between them, so-called general "laws" and "properties" of nature. The complex sciences, on the other hand, deal, with little or no abstraction, with those objects of reality that are accessible to man in the atmosphere, the hydrosphere, the lithosphere and the biosphere.† Their work comprises two types of inquiry. One is concerned with abstractions to the extent of dealing with types rather than individuals-that is, with such things as plants, animals, protoplasm; clouds, streams, glaciers; volcanoes and mountain ranges. It comprises the search for general properties and patterns of behavior or "laws" that characterize the objects and their reactions to each other. These properties and laws apply always, everywhere. They are independent of the stream of time. We may call the results of this sort of inquiry timeless knowledge. The other type of inquiry is concerned with the objects themselves-that is, with this animal and that plant; this river system and that mountain chain; this glacier and that valley. Like all concrete objects in nature, they are subject to change with the passage of time, especially when it is measured in years, centuries, eons. The characteristics by which we recognize them -indeed, their very existence are dependent on their position at this point in the stream of time. This we may call time-bound knowledge. The so-called descriptive sciences are all bound to the past of which the objects of their study are the product and through which alone their present properties can be understood. They are historical sciences. This obvious fact is easily overlooked, which leads to serious misunderstanding, as we shall see later. Dynamic Geology With this broad picture in mind, let us now examine the nature of geological inquiry, defining, for the purposes of this discussion, geology as the science of rocks. Air is not a rock; water is. Meteorology and climatology are, correspondingly, gen-

Jan 1, 1941

By W. E. D. Jr. Stokes

THE application of aviation to mining and petroleum operations, on the basis of economy and attainment, has become a demonstrated fact. According to Dominion Government records, 30 Canadian companies engaged in air transportation with northland mining camps, carried 13,000 tons of freight in 1935, and in 1936 carried 16,000 tons. In addition, many mining companies used planes to transport prospectors with canoes, outboard motors, gasoline drums and supplies to remote locations, and one company maintained a plane to take radium-bearing ore from its mine on Great Bear Lake nearly 1000 miles south to the rail-way at Waterways, Alberta. Heavy pieces of mining machinery weighing 2 tons are being carried by Ford trimotor planes over the Andes, at an altitude of not less than 15,000 feet. At Bulolo, New Guinea, 17,500 tons of disassembled gold-dredging equipment has been flown over inaccessible terrain, while supplies and building materials for a community of 1000 whites have been transported by airplane. A 31 z-ton shaft was carried on one notable trip, while at another time an automobile, 2 tons of rice and a large safe went over the mountains in one plane. Fig. 1 shows an electric generator that was carried by plane to Bulolo. Many large American oil companies operated fleets of planes during 1936, ranging from fast, luxurious air liners for executives to elaborate geological prospecting units, ambulance planes, freight carriers and pipe-line repair crews.

Jan 1, 1937

By K. Kim

A site characterization strategy formulated for the probabilistic design of underground structures is presented, which takes into account the variability of rock properties and the stochastic nature of the rock failure process. It entails determining probability distributions of rock properties by utilizing the theory of extremes and Monte Carlo simulation. Laboratory and field test data are analyzed and presented to illustrate the methodology. The results indicate that the distributive characteristics of rock mass properties can be estimated using empirical relationships currently available. This results of analyses can be incorporated into the design of underground structures, and then, the relative uncertainties of the failure probability of the structures can be assessed.

Jan 1, 1995

By G. M. Ritcey, A. W. Ashbrook

"This paper summarizes the optimum leach conditions for each Of several cobalt-containing arsenical feed materials, describes the solution treatment prior to purification of cobalt recovery, and discusses the plant operation on one feed as well as the treatment of effluents.IntroductionDuring the period 1962-1964, when the demand for uranium was low, Eldorado Mining and Refining Limited (Eldorado Nuclear Limited) made a decision to undertake a three-year diversification program. One area chosen in this program was that concerned with the processing of cobalt-nickel materials. Many such materials were evaluated over the three-year period, ranging from tailings, residues, ores, concentrates and speiss to metal scrap. Cobalt feed materials, on which much of the effort was concentrated, were those containing arsenic together with other metals such as silver, copper, nickel and iron. This paper describes the treatment of arsenic-bearing feed materials (ranging from 0.3 to 570/0 As) and the subsequent purification stages required before the separation and recovery of high-purity cobalt. Because of the current interest in treating cobalt ores, it seemed appropriate that the information on the treatment of various cobalt feeds should now be made available . Although a large amount of data were generated during the research and process development program, a complete scientific correlation and understanding could not be achieved. Nevertheless, the data may provide a guide to others involved in processing not only cobalt, but other arsenical ores."

Jan 1, 1981

By BARRY BANNATYNE

Ombrotrophic Sphagnum peat bogs have a characteristic signature on both colour injrared film (750 nm to 3,000 nm response) and Daedalus injrared line-scanner images (thermal infrared 3 to 5 microns and 8 to 14 microns response). This remote sensing method was used to survey bogs in southeast Manitoba to delineate targets for surface exploration. Target bogs all have a surface growth of Sphagnum; underlying dead Sphagnum ranges from 1 to 6 m thick. Large Sphagnum reserves exist in the Caribou cluster of bogs, and in /979 a bog first identified by infrared sensing was brought into production.

Jan 1, 1984

By Brett P. Spigarelli

"To meet the growing need for CO2 capture and storage technology, Michigan Technological University is studying CO2 capture using alkali-based solvents. The objective of the present study was to find a way to increase the absorption rate of CO2 into an alkali solution without reducing the absorption capacity of the solution. One approach to increasing absorption rate is to use a surfactant to chemically alter the gas bubble size. The surfactant chosen for the study was a neutral-charge polypropylene glycol methyl ether (PPGME) with a molecular weight of 200. Experiments were conducted to study the absorption rate of CO2 at varying surfactant concentrations. Results showed that as the concentration of PPGME increased in solution, the absorption rate also increased. The CO2 absorption rate increased from 3.45 x 10-3 mol/min CO2 at 0g/L PPGME to 3.92 x 10-3 mol/min CO2 at 0.48 g/L PPGME. This amounted to a 14% increase in the CO2 absorption rate with no decrease in the absorption capacity of the solution. IntroductionChemical absorption using an amine solvent is currently the most mature carbon capture and storage technology available. Amines are advantageous in that they have a fast CO2 absorption rate, which leads to a high CO2 removal efficiency. However, amine absorption has some considerable drawbacks, such as high energy requirements, high equipment corrosion rates, amine degradation in the presence of oxygen, high waste generation and a large increase in plant footprint if new equipment is constructed (Herzog and Golomb, 2004; D’Alessandro et al., 2010). Due to these drawbacks, Michigan Technological University (MTU) is studying CO2 absorption using alkali-based solvents, which address the above disadvantages of amine solvents."

Jan 1, 2015

By Paul E. Senseny

Data from triaxial compression tests per- formed at confining pressures between 0 and 100 MPa are used to evaluate parameters in a contitutive model that is based on microcracking. The tensorial formulation is reduced to equations that are specific to the simple Loading imposed in triaxial compression tests. Procedures for evaluating the model parameters are described, dependence of parameter values on confining pressure is discussed, and prediction of failure is assessed.

Jan 1, 1986

By W. J. Schlitt, J. H. Templeton

The chemical reactions that occur within a copper-leach recovery system are discussed, and the impact on the overall acid balance is evaluated. Both oxide and sulfide mineralogy are addressed, and their effects on acid consumption, generation and solution buffering are presented. Two case studies that apply the discussed chemistry show the practicality of using a computer spreadsheet acid-balance model for the early planning and design of copper-leach systems.

Jan 1, 1998

By P Bellairs

The Hamersley Province is located 1OOOkm to the North of Perth .the Capital City of Western Australia and is of major economic significance due to the mining of extensive deposits of Haematitic Iron Ore for both domestic and export use. A small but significant proportion of the waste associated with these deposits presents problems due to its ability to spontaneously combust and react with explosives resulting in premature detonations.

Jan 1, 1996

By L B. Zhou, S Li, B L. Wang, S B. Li, Q Wang

The rapid development in ChinaÆs metal mine resources has caused a series of mine environment problems such as serious ecological damage and environment pollution, and secondary geological disasters. The paper has reviewed ChinaÆs metal mine development, including current status and environmental situation, analysed existing problems in mine development and environmental management, and proposed corresponding countermeasures and suggestions.CITATION:Wang, B L, Li, S B, Li, S, Zhou, L B and Wang, Q, 2012. Current situations, problems, countermeasures and suggestions for ChinaÆs metal mine development, in Proceedings Life-of-Mine 2012 , pp 353-356 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

Ore Reserves estimation for the two producing copper orebodies at Isa Mine, Mount Isa, Queensland is discussed. The principal estimation techniques used and discussed are first, a computer based inverse power distance weighted assay meshing technique, and second, a manual arithmetic averaging technique. The principles involved in these techniques are compared, and their areas of application indicated. A general comparison of the estimation of reserves with eventual production is presented.

Jan 1, 1979

By J. A. Hurd

Towards the goal of a better understanding of the structure-proton conductivity relationship in PEM materials, this project concerns the design of ordered polymeric solids containing well-defined sulfonate aggregates. The approach employed involves the templation of sulfonated monomers using core principles of crystal engineering. In addition to sulfonate groups, the monomeric units contain crosslinkable functionalities to enable formation of a covalently linked network. The templation strongly directs the construction of well-defined sulfonate clusters and aggregates. Structural, sorption and conductivity data for the networks will be shown.

Jan 1, 2005

By Henry Stoch

It?s a green, green world ? Public concern about the impact of human activities on the environment and the roles that businesses play in that impact is rising. What?s happened in the last few months? ? Recent news: ? British Columbia announces carbon tax in 2008 budget ? Federal Court ruling stalls oil sands approvals due to a lack of consideration of GHG implications ? US Energy Independence and Security Act could limit government procurement of oil sands-derived fuels ? Western Climate Initiative (WCI) suggests a ?first seller? approach for regulating generators outside WCI jurisdictions ? Implications ? A cost for carbon has arrived ? The lack of a GHG strategy can have a material impact on your business ? Regulations in other jurisdictions could affect your organization

May 1, 2008

Pilot-Scale Study of Deep Cone Thickener for Phosphatic Clay Dewatering

Sep 13, 2010

By Caroline Gerwig, Joseph R. Wickline, Zach Agioutantis

In longwall mining, the progressive caving of the roof allows stored energy to dissipate over an extended time. However, in some cases, the roof strata above the longwall panel are unusually strong and do not break with the movement of the working face. Instead, the roof material bridges over the expanse of the longwall, forming an unstable beam. Later, when this beam breaks, the stored energy can release suddenly, causing a seismic event to propagate to surrounding mine workings. The focus of this paper is to estimate the size of beams that form over longwall panels to the seismic energy recorded by the mine. Analytical calculations are used to verify two-dimensional models of longwall roof beams to determine the strain energy and gravitational energy developed, which is then released upon strata failure to surrounding mine workings. Models are developed using RS2 to model the stress, strain, and deflection along the bottom of the longwall roof beam to calculate gravitational and strain energies. Gravitational energy is shown to be the main driving factor in energy release, except for the beams with low heights. Analyses allow the determination of beam characteristics based on seismic data. The analysis is refined using swelling factor to compare various beam drop heights. The models show an increase in seismic magnitude for higher drop heights. However, the actual data provided by the Buchanan mine displays a decrease in seismic magnitude with increasing drop height, indicating that energy is dissipated into the broken gob material as drop height increases.

Jul 1, 2023

By M. Kumral

Raw material fed into a processing or refining plant is required to be uniform in composition for several reasons. When the mined ore is highly variable in quality the only way to ensure consistency is to homogenize the ore prior to the process. The problem is more complicated in the case of multiple ore sources. The idea behind the research is that theoretical blending ratios can serve not only to meet predefined specific criteria but also to reduce grade fluctuations of variables under consideration. In this paper, the problem is formulated as a quadratic programming problem, whose objective function is in quadratic form and constraints are linear. A case study was conducted on a data set from an iron orebody to demonstrate the technique. The objective was to minimize the blend variability in terms of each variable (in this study, iron, silica, alumina and lime) grade of ores extracted in three different production faces. The stockpile capacity, lower and upper limits of each variable satisfying operational requirements and non-negativity were constrained to the model. A modified simplex method developed by Wolfe was used for solving the blending and homogenization problem. The promising results can be used as apart of the stacking and reclaiming design. Keywords: blending and homogenization problem, quadratic programming, Wolfe method.

Jan 1, 2005

By Franz Walchshofer, Mark Kuchta, Nobuharu Isago, Ugur Ozbay, Wolfgang Dolsak

A series of in situ pull test were performed on a new design friction stabilizer bolt with the objective of determining its performance characteristics. The bolt is installed while drilling, thus improving safety and significantly reducing the installation time. An optional expansion element can be inserted into the bolt to provide an end-anchorage, which further increases the bolt’s capacity. In situ tests show that the pull capacity of the 2 m long new design bolt is about 15 tons. When installed with an expansion element, the pull capacity of these bolts becomes as high as 30 tons.

Jan 1, 2005

By Junnosuke Yamamoto

Substituting sodium hydroxide for sodium carbonate as a binder in a glass batch yields harder pellets with a lower melting point. This paper explores the degree of NaOH substitution that is feasible, and compares pellet hardness, and amount of dusting with the degree of NaOH substitution. The effects of the the amount of soluble silicate in the pellet and residual hydroxide concentration in the pellet on pellet hardness are also studied.

Jan 1, 1977

By Joseph C. Rota, Charles E. Ekburg

Introduction The Gold Quarry gold deposit is the largest bulk tonnage epithermal gold deposit in northeastern Nevada to be developed by Newmont Gold Co., formerly known as Carlin Gold Mining Co. Exploration and development of the deposit extended over a period of nearly 50 years before bulk tonnage mining became economically feasible. Proven reserves at Gold Quarry are currently estimated at more than 255 t (8.2 million oz.) of gold, accounting for more than 40% of the total Carlin Trend mineable reserves for 1986. Milling began in late 1985; dump leaching of lower grade ores began in May of 1986. The mill has exceeded the initial design throughput rate of 6.3 kt/d (7000 stpd) and is now processing more than 8 kt/d (9000 stpd). The dump leach facility will process more than 7.3 Mt (8.1 million st) of lower grade ores in 1986. The Gold Quarry ore body is to be developed by an open pit that will eventually be 1830 m (6000 ft) long, 1220 m (4000 ft) wide and 300 m (1000 ft) deep. The mine currently produces 77 kt/d (85,000 stpd) on a 24-hour-a-day, seven-day workweek. Planned pit production will increase to nearly 168 kt/d (185,000 stpd) in 1988. Production equipment currently includes one Demag H-/285, three Komatsu PC-1500 hydraulic shovels, two Cat 992C loaders and 21 90 to 135 t (100 to 150 st) haul trucks. Mining is conducted on 8 m (20 ft) benches within the Paleozoic

Jan 4, 1988