Search Documents

By J. Daniel Bryant

Deformation processing of rapidly solidified powder alloys presents a technical challenge different in several ways from the processing of ingot based alloys. The metastable phases formed during planar flow casting of aluminum alloy 8009 (FVS0812) must be safe-guarded from high temperature excursions during processing to avoid decomposition; this restriction prohibits liquid phase sintering of particles during consolidation. The development of strong particle-particle adhesion, therefore, relies on the imposition of very large strains during forming operations to insure sufficient mechanical meshing of the aluminum particles and break-up of prior particle oxide boundaries. These strains are generally much greater than those required for metallurgical transformations in ingot based alloys. In an attempt to quantify the deformation required to improve interparticle bonding, the finite element method (FEM) was employed. Preliminary results which predict the metal flow and strain distribution in several workpiece configurations are discussed. These predictions are then correlated to measurements made on experimental subscale forgings. Lastly, experimentally measured quantities which reflect the degree of interparticle bondingg are related back to FEM model predictions.

Jan 1, 1992

By Persifor Frazer

1. SMOKE PREVENTION. Report of Select Committee of House of Commons (1843). Nuisance considerably abated in Leeds (Wm. Backerd, July 13, 1843, 239 pages). A synoptic index, p. 211, gives, in alphabetical order, the digest of every subject taken up. 2. FUEL : ITS COMBUSTION AND ECONOMY. D. Kinnear Clark, C. E. 24mo, 1354 pp. Crosby Lockwood & Co., London (1880). Includes abridgement of treatise on combustion of coal and prevention of smoke, by C. W. Williams, A.I.C.E. 3. DIE RAUCHSCHÄDEN IN DEN WÄLDERN DER UMGEBUNG DER FISCALISCHEN HÜTTENWERKE BEI FREIBERG. Dr. J. v. Schröder, Professor in Tharand, and Dr. A. Schertel, Vorstand des Hüttenlaboratoriums zu Freiberg. Royal 8vo, 27 .pages, 19 pages of tables and a map. Ernst Maukisch, Freiberg (1884). (Aus dem Jahrbuch für das Berg- und Huttenwesen, 1884.) In 1861, Reich and Stockhardt examined the extent of injury to vegetation by the Muldner works. Needles and twigs of pine showed in 100,000 parts : Pb, 5 to 50 ; As, 3.3 to 14.3 ; S02, 62 to 120. In the top twigs, 5 to 8 ; needles, 10 to 16 ; thicker twigs, 10 to 22 ; thinner twig-ends, 17 to 54 of lead. Lead greater in amount in sickly twig-ends with few needles ; also in the bark than in the naked wood of the trunk, which had hardly a trace ; also in the part turned toward the works than on the opposite side. Pb and As diminished in the vegetation with distance from the smelter ; and the same with regard to the soil. Fresh snow was collected, and SO, As, and Pb detected in it.

May 1, 1907

By C. Feliciano, M. Cavalcante

A large iron ore open pit mine in Brazil operates with reduced blast sizes, due to the imminence of red alerts in the rainy season and the proximity of plant and dam structures that demand control of the maximum load of fired explosives. Blasts are currently not allowed to remain loaded with explosives due to the risk of red alerts, limiting mine operations close to them. There is a need to increase the blast sizes, reducing the number of events required to obtain the planned mass and, consequently, the unproductive operating hours lost with mine evacuations. The WebGen™ wireless electronic initiation system is a technology for firing detonators via lowfrequency magnetic induction that propagates through the medium, without physical connection. A blast was carried out with 406 holes divided into 4 panels, aiming to validate the preloading technique with wireless detonators and its performance in safety and productivity. The absence of lead wires in the system eliminates the risk of interaction between vehicles and detonator cables in stemming and loading operations, which can result in unplanned detonation or misfire. By eliminating the need for a spotter, it reduces people's exposure to dust and the risk of human-machine interaction. Furthermore, it eliminates the risk of unplanned detonation caused by lightning strikes. The pre-loading technique with wireless detonators enables flexibility and efficiency in planning through temporary accesses over loaded areas. In the demonstration, driving over the loaded area was essential to avoid jams and excessive wear on equipment due to the narrow berm and very friable material. Another gain in productivity was optimizing operational stages, since detonators were programmed in parallel with loading, anticipating process stages, in addition to eliminating the need to connect detonators. Considering the average handling and savings in downtime due to the reduction of blasting events, a potential increase in movement of 49,000t (54,013 short tons) in 3 months was estimated, keeping the vibration results within the required limit. The trial with wireless detonators demonstrated the feasibility of carrying out blasts with preloaded panels, without restrictions on the number of panels or detonators, enabling vibration control, innovating mine planning and increasing safety and productivity

Jan 1, 2024

By A. K. Andersen

One of the prime examples of the versatility of the MARCONAFLO system, which is a body of technology comprising the means to handle, store, load, transport, discharge and reclaim mineral commodities in slurry form, is the direct application of this process to leaching ores. The initial approach was to provide a much improved materials handling system for the transport of copper ores; however, an extensive development program, inclusive of prototype and pilot plant tests, has established that a new leaching concept is possible with this system. Data are presented from the leaching operation of a 25 TPD pilot plant utilizing a copper-oxide ore, mainly chrysocolla. This pilot plant was designed to incorporate true countercurrent flow where the ore is actually in motion, as contrary to vat leaching operations, and the ore being successfully leached is fine crushed ore (3/8-inch x o), contrary to agitation leach circuits. Extractions in excess of 85% of the soluble values are common with only 15 hours of retention time in the MARCONAFLO leaching system.

Jan 1, 1975

By Nobuaki Sato

The electrical conductivity, k, of pure and sodium doped sulfur melts was measured with and without ultrasonic waves at temperatures ranging from 140 to 340° C by the two probe method using an ultra high resistance meter. The II: value of the pure sulfur melt with irradiation jumped at around 170°C by an order of 102 after which it monotonically increased from 10-5 to 10-4 (omega) 1cm-4 with an increase of the temperature. The addition of the sodium metal to the sulfur melt was found to cause a larger jumping in the II: value. The II: value increased with the increase of Na proportion in the melt. For a 10 mol% Na doped sulfur melt it was as high as max. ~30 (omega) 1cm-1 above 180°C under the irradiation of ultrasonics.

Jan 1, 2003

By R. M. Enick

A novel liquid-liquid separation for the recovery of free or liberated gold from mixtures of fine particles was evaluated. The separation, conducted at ambient temperature and a pressure of about 1000 psi a, was based on the difference in wettability of precious metals and minerals. Contact angle results indicated that in the presence of water and liquid CO2, gold, platinum and silver had intermediate wettability. Minerals such as quartz and magnetite, however, were hydrophilic. Therefore fine gold particles. -325 mesh, that were mixed with water and liquid CO2 dispersed in the CO2 or agglomerated at the H2O-CO2 interface while the minerals tended to remain in the aqueous phase. Best results were obtained when these fine gold particles were liberated, were not agglomerated in slimes, were not adhering to minerals, and were not coated with minerals.

Jan 1, 1998

By Tracy Brettmann, Will Bohlen

An innovative retaining wall design consisting of tangent drilled shafts with supplementary seal piles was used to limit continuing bank erosion along the Brazos River in Southeast Texas. The riverbank erosion had progressed to where it was threatening the stability of both the bridge abutment and corresponding approach embankment of the heavily travelled Highway 99 bridge at this location. A tangent pile design was selected because it was both much faster to install and more cost effective than a secant pile system. The design included both 5.5-ft and 10-ft diameter shafts with depths up to 130-ft and comprised both anchored and cantilevered sections. Supplementary seal shafts were also installed between the structural tangent drilled shafts to help plug any gaps between the tangent shafts. The plumbness and diameter of the shafts were tested using a sonic caliper to make sure the shafts were installed within the specified tolerance. The initial design had to be revised when a record flood from Hurricane Harvey impacted the site during construction. Introduction The Fort Bend Grand Parkway Toll Road Authority (Owner) needed to protect the north bridge abutment with a retaining wall system due to rapidly eroding conditions of the Brazos River banks within the 300- feet-right-of-way of the State Highway 99 Jodie Stavinoha Bridge. The extent of the local scour and erosion along the north bank of the Brazos River has caused concern for the structural integrity of the bridge. The magnitude of the erosion along the north bank at the location of the bridge has been measured at about 120 feet over three recent hydrologic flood events locally referred to as Memorial Day 2015, Memorial Day 2016, and Tax Day 2016. During construction, a new record flood level occurred due to Hurricane Harvey in August of 2017 that resulted in a portion of the retaining wall needing to be redesigned due to even more erosion occurring. The Brazos River is an actively eroding and meandering alluvial river plain that naturally meanders and migrates over time. The processes of bank erosion and meander migration were ongoing before the bridge was constructed and will continue in the future. These recurring major flood events, however, rapidly increased the rate of erosion in just a few years. Background. Due to the need to protect the bridge as soon as possible, the Owner selected a project team consisting of the designer, general contractor and specialty deep foundation contractor prior to final design to work together in developing a cost-effective design that could be implemented rapidly. The project team initially considered both a secant pile and tangent pile retaining wall system using drilled shafts. After reviewing various alternative designs, a tangent pile wall with seal piles was selected based on both cost effectiveness and speed of installation. The tangent pile with seal pile option was approximately 20 percent lower in cost and 50 percent faster to install.

Jan 1, 2018

By Mizuta T, Sakurai M

The Pine Creek Inlier produced 12 440 kg of gold in the period from the first gold discovery in the 1860s to the early-1900s. During the 1930s renewed large-scale prospecting took place and gave a foothold for today's gold mining operations. The rise of the gold price and improved mining methods in the 1970s and 1980s made possible low cost, bulk low grade mining operations. Various gold deposits including vein, network and stratiform types occur in the Pine Creek Inlier (Nicholson and Eupene, 1990). The Tom's Gully deposit is located 100 km south-east of Darwin in the Northern Territory. It is hosted in the early Proterozoic Wildman Siltstone and lies north-east of 1800 my old Mt Bundey Pluton (Figure 1). Around the Mt Bundey Pluton, there are several prospective base and precious metal deposits such as Quest 29. The Tom's Gully gold deposit was discovered in 1986 and yielded a total of 3070 kg of gold from ore averaging 9.35 g/t gold between 1987 and 1990 when the mining operation was terminated.

Jan 1, 1994

By Pedro Jorge Walburga Keglevich de Buzin

A qualificação das sucatas ferrosas e beneficiamento por moinhos shredder são operações utilizadas pelas usinas semi-integradas com objetivo da melhoria na produtividade e qualidade do aço produzido. Um benefício adicional é a redução de impurezas e a melhoria da qualidade ambiental desta matéria-prima. Neste trabalho é avaliada a influência da qualidade da sucata no teor de cloro e de metais residuais em poeiras de aciaria elétrica provenientes de três usinas semi-integradas, com diferentes perfis de produção. Os resuItados alcançados mostraram uma possível redução do teor de cloro de cerca de 50% com a utilização de sucata processada por shredder. Os menores níveis de cloro potencializam a aplicação posterior de métodos para adequação do teor de cloro, favoráveis à reciclagem, incorporação ou coprocessamento destas poeiras.

Oct 30, 2017

By Howard Lum, Sergio Valles, John Bednarski, Gordon Enas, Jay Arabshahi

"Water drawn from the Sacramento-San Joaquin Delta provides water supply to 66 percent of California’s population and supports the state’s agriculture industry. The existing through-Delta water system is outdated and unreliable with environmental risk to some fish and wildlife species. The Bay-Delta Conservation Plan (BDCP) has been established to environmentally retrofit and modernize California’s water delivery system through the Delta by restoring habitats, constructing new diversion points in the north Delta and providing a means to transport water supplies under the Delta, rather than through sensitive natural channels.Under BDCP, the Delta Habitat Conservation and Conveyance Program (DHCCP) has developed several alternatives to convey water from the Sacramento River in the north to the existing pumping facilities in the south Delta through an isolated conveyance system. The new conveyance system would become an integral part of the State Water Project (SWP) and the federal Central Valley Project (CVP) by transporting water to the export pumping plants for each of these projects. The DHCCP is managed by the California Department of Water Resources (DWR), while state and federal water contractors provide technical support to the program.The initial conceptual study efforts on the overall program commenced in 2007 and examined various options for the proposed conveyance system. Several conveyance alternatives were analyzed at that time. The Conceptual Engineering Report published on Oct. 1, 2013 identified the modified pipeline/tunnel option (MPTO) as the preferred alternative to be included in the BDCP environmental documents. MPTO includes three river intakes and pump stations along the Sacramento River, various sizes of pipelines and tunnels, junction structures and two forebays that are capable of delivering up to 4 million gpm (9,000 cfs) from the Sacramento River to the SWP and CVP. The river intakes are located near Hood in Sacramento County approximately 64 km (40 miles) from Clifton Court Forebay (CCF) in Contra Costa County. This route would cross portions of Sacramento, San Joaquin and Contra Costa counties. Figure 1 depicts the configuration of the MPTO alternative."

Apr 1, 2016

By P. Tittes, M. Deal, M. Spicher, S. McDaniel, J. Wickens

"Haile Gold Mine is located near Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The relatively low grade and refractory nature of the deposit has been a challenge for efficient processing since the start of mining on the property. Early processing techniques included gravity separation and barrel chlorination. The last operation employed heap leaching in 1985 through 1992. After being closed and reclaimed for over 20 years, the property is poised to re-open and produce once again. In this chapter of the Mine’s legacy, flotation and ultra-fine grinding will be employed to achieve economic extraction of gold and silver from the pyrite. This paper briefly reviews some of the mine’s history, the metallurgical testing, the flowsheet and discusses design considerations.INTRODUCTIONHaile Gold Mine is located near Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The last operation employed heap leaching in 1985 through 1992. Since then, the property has been closed and fully reclaimed. Romarco Minerals acquired the property in 2007, and began an exploration program that has delineated over 62 tonnes (+2M ozs.) of gold in reserve at an overall grade of 2 ppm (0.06 opt). This paper provides a brief history of the property, a summary of metallurgical testing, description of the process flowsheet and discusses design considerations.HISTORY1827 – 1837Gold was discovered in creek beds on the Haile property in 1827. The property was owned by Benjamin Haile, and the first few years of production came from placer mining. After gold was discovered in schist beds to the sides of the streams, Haile expanded the operation by leasing 18 meter-square (50 ft.) plots to local planters. These planters used slaves to work the small excavations in the agricultural offseason. The gold ore was taken to arrastras where the free gold was liberated and recovered. The excavations were above the water table, generally less than 18 meters (60 ft.) down, and it was noted then that gold could be found embedded in sulfides and difficult to extract."

Jan 1, 2013

By Darryel Boucher, Thomas W. Leadbeater, Raymond Langlois, Joshua Sovechles, McGill University, Zhoutong Deng

"Spiral concentrators are used to upgrade ore based on the density difference between their component minerals. This simple flowing film gravity separator is of interest for the processing of large amounts of material, as found in the iron ore industry. Addition of wash water at different points on the trough of the spiral affects the grade and recovery of the valuable concentrate by affecting the flow of particles within the thin slurry film. This paper shows how radiolabelled hematite (-355+300 µm) and quartz (–1,180+1,000 µm) tracers were used to determine the particles’ behaviour within the slurry film with and without the addition of wash water. The results presented provide a detailed particle flow pattern around a wash water addition point and its effect on the trajectory and velocity of the particles. This information is of interest in building knowledge about spiral wash water injection parameters such as injection location, direction, flow rate and nozzle orifice type (affecting jet shape and velocity).INTRODUCTIONSpiral concentrators are density based separation devices. They are extensively used in the upgrading of iron ore, fine coal and minerals sands (sources of ilmenite, rutile, zircon and monazite) (Wills & Finch, 2016). A spiral unit is composed of a channel of specific profile formed as a helix of 3 to 7 turns around a central structural post. The feed pulp is composed of 15 to 45% solids with particle size from 75 µm to 3000 µm (Wills & Finch, 2016). Throughput of a single spiraling trough can be up to 8 ton per hour and multiple trough unit (up to four trough) can process up to 30 ton per hour for a footprint of around 0.7 m2 (Palmers & Vadeikis, 2010). They are low cost concentrators considering manufacturing of their trough via polymer reverse molding. The energy intensity of a spiral plan is notably small considering the throughput and is mostly related to pulp pumping and final concentrate dewatering."

Jan 1, 2016

By N. Theron, R. F. Meeser

The global emphasis on conserving energy resources has led to the adoption of hybrid power systems in vehicles. Optimally applied, hybrid systems can save up to 40% on fuel costs. To optimally manage a hybrid vehicle's energy flow it is necessary to know, in real time, all the energy requirements to complete a given route. The energy consumption depends mainly on the vehicle mass, speed profile, and route topography. Of these, the topographic profile is the one factor that is only route-dependent and not influenced by the vehicle or driving styles. The heading vs. distance profile is also an example of a route characteristic not influenced by the vehicle or driving style. In this study the topographic and heading profiles are used to identify routes, and are easily measured by means of digital barometric pressure and compass sensors. Correlations between the current route and previously travelled/stored routes are performed based on their topographic and heading profiles in a point-by-point manner. Above-ground tests were first performed using a road vehicle and six routes to evaluate the system. The system consistently and correctly identified a 20 km route within the first 4 km. It also proved to function correctly in underground tests through the implementation of an instrumented hand-held surveyor's wheel. This system finds direct practical application in optimizing the energy management of an underground hybrid locomotive used by the mining industry in South Africa, but can also be of benefit in applications where route identification is required and using GPS is not feasible.

Jan 26, 2023

By G. L. Kothny

Developments of well-surveying instruments, coring .and core orientation, were in an advanced state when drilling for oil began—these developments actually originated with the mining industry.' Surveying of oil wells was not generally used in the United States until Alexander Anderson2 disclosed that the majority of wells drilled with rotary tools were crooked, with average horizontal drifts of about 516 ft. for holes 5000 ft. deep and about 793 ft. for holes 6000 ft. deep. This disclosure brought about the development of many additional instruments for surveying oil wells during the progress of drilling and after their completion. Surveying of boreholes, during the process of drilling at regular depth intervals, became a standard practice in the petroleum industry. Some producing states even established laws making check surveys mandatory, during drilling and under certain conditions also after completion. The surveying of boreholes also brought about changes and improvements in drilling practices. It provides information for the guidance of the hole while drilling, and for plotting the course as the work progresses, enabling the driller to take corrective measures immediately and with the least expense. The reasons for drilling straight holes are too well recognized to warrant any full discussion of them here. Straight holes are less costly to drill, because they reach the object on the shortest course. Table I shows the horizontal drift and loss in vertical depth for various angles of inclination. It is not surprising, therefore that many drilling contracts for oil wells today limit the drilling contractor to a maximum inclination off the vertical of 2° or 3O. In the mining industry the reasons for drilling straight holes are still more serious. A crooked hole may miss an ore body underground or provide incorrect information regarding an ore body. Types of Surveying Instruments The surveying instruments used in oil-well drilling may be classed in two types: I. Inclinometers, recording inclination only.

Jan 1, 1949

By C. H. Lee

The world-famous Sang Dong Mine in the Republic of Korea has long been one of the world's greatest tungsten ore deposits. Over the years, the development of the Sang Dong deposit has steadily increased to a point where it now exerts a great influence on the world tungsten market. The mine is located in the mountains of the province of Kang Won Do, approximately 150 miles by road due east of Seoul, the capital of the Republic of Korea. In recent years the transportation system in Korea has greatly improved and the mine is now serviced by an excellent secondary type road from the new railroad line which is 20 miles away. The Sang Dong operation is made up of the underground mining, beneficiation mill, chemical refinery, tungsten metal plant, bismuth refinery, acid plant, foundry and machine shops. The bismuthinite production from the Sang Dong Mine is also of considerable importance, The output accounts for nearly 10 per cent of the world production of bismuth. A small amount of molybdenite concentrate is also recovered from the flotation operation.

Jan 1, 1962

By Robert Charles Alfred

Evolution is continuing in the field of rock drilling, Campbell Limestone Company is experimenting in the higher air pressure phase of drilling, It has been determined that there is a definite relationship between Air Pressure, Penetration Rate, Bit & Tool Wear and Life, In our drilling we have determined that &e higher air pressure gives a better penetration rate with less bit wear per foot. Drilling with 180 to 200 PSI air pressure, instead of 100 PSI for air and/or churn drills, has decreased our primary costs by approximately one half.

Jan 1, 1963

By D. B. Taliaferro

Information regarding the pores or voids in reservoir rocks is vitally important in the scientific extraction of petroleum from natural underground reservoirs, and petroleum technologists concerned, with subsurface, conditions have devised various methods that give reasonably accurate information as to the porosities of oil and gas-bearing sands.5/ In this, work, several investigators have made use of the experience of the ceramic and other industries. The method of determining the effective porosity of oil sands described in this report falls within the general classification of gas-expansion methods. It was devised and developed at the United States Bureau of Mines Petroleum Experiment Station, Bartlesville, Okla., as a part of the research dealing with fluid and energy relations in reservoirs and improved oil-recovery methods. The apparatus and procedure are well adapted to the requirements of the Bureau, and the following detailed description has been prepared so that others may make use of the information. A tabulation at the end of the report gives the results of several hundred porosity determinations for oil sands in fields of 11 States.

Jan 1, 1937

By D. B. Taliaferro

Information regarding the pores or voids in reservoir rocks is vitally important in the scientific extraction of petroleum from natural underground reservoirs, and petroleum technologists concerned. with subsurface conditions have devised various methods that give reasonably accurate information as to the porosities of oil and gas-bearing sands.5/ In this work, several investigators have made use of the experience of the ceramic and other industries. The method of determining the effective porosity of oil sands described in this report falls within the general classification of gas-expansion methods. It was devised and developed at the United States Bureau of Mines Petroleum Experiment Station, Bartlesville, Okla., as a part of the research dealing with fluid and energy relations in reservoirs and improved oil-recovery methods. The apparatus and procedure are well adapted to the requirements of the Bureau, and the following detailed description has been prepared so that others may make use of the information. A tabulation at the end of the report gives the results of several hundred porosity determinations for oil sands in fields of 11 States.

Jan 1, 1937

By Artur Frederico Fonseca da Cruz

Com a necessidade urgente e constante de aumento da competitividade no cenário atual da mineração, mostra-se fundamental o desenvolvimento constante de novos parâmetros de processo combinados a uma estratégia de manutenção focada não só na disponibilidade dos ativos, e sim no desempenho dos equipamentos. No que tange ao processo de pelotização neste trabalho foi dado foco especificamente na configuração de perfis de queima no forno de grelha móvel, onde foram testados quatro perfis e fixado o perfil nº 04 otimizado via sistema de otimização de processo para níveis de produções diferentes, equilibrando qualidade e consumo específico de gás natural, no período anterior e posterior à parada fria. A partir daí foram analisados parâmetros de qualidade, produção e processo, comparando-os entre antes e após a parada fria. Foram registradas melhoras nos índices de qualidade e redução de aproximadamente 13,50% do consumo específico de gás natural e 10,80% de redução no consumo específico de energia elétrica de ventiladores por níveis de produção.

Aug 17, 2017

By R. T. Tshikhudo

Nanotechnology can provide solutions to many of the world?s socio-economic challenges. The application of nanomaterials for water treatment and analysis, point-of-care diagnostics and targeted drug delivery systems or devices could improve the quality of life for people in developing countries. Gold colloids have a long history (dating back to the 4th century AD) and are particularly well known for their aesthetic appeal and their therapeutic properties. Since Faraday published a report on the synthesis and properties of colloidal gold in 1857, a reasonable insight into the nature of gold sols (nucleation, growth and kinetics of coagulation) has been developed. Considerable attention has been drawn during the past few decades to the development and optimization of methods for the preparation of gold nanoparticles. In nanoscience and nanotechnology today, gold nanomaterials appear to be the most widely used material by both academics and industrialists. This is due to the extraordinary properties of gold nanoparticles (e.g. optical, catalytic, and magnetic?they are also known to act as strong Raman enhancers and may also amplify fluorescence under certain circumstances). Mintek, through Project AuTEK and the DST/Mintek Nanotechnology Innovation Centre (NIC), has been at the forefront of the development of new industrial uses for gold. Mintek?s gold nanotechnology programme focuses on the development of gold-based nanostructured materials and their applications in health, water and other related areas. While few projects use gold nanoparticles for water treatment and analysis, Mintek?s gold nanoparticles are widely used in the health sector. For example, gold nanoparticles are engineered and produced in large quantities as systems for targeted drug delivery. They are also used as tools for advanced rapid diagnostic tests. Both optical and electrochemical rapid diagnostic methods are developed for the human and animal health sectors for point-of-care testing. This paper gives a brief introduction and overview of gold nanotechnology, and desrcibes the development of some of Mintek?s gold nanoparticle targeted drug delivery systems and lateral flow point of care prototype devices.

Jan 1, 2009