Search Documents

By Wojciech Klecan, John H. Raymer

Baseline quantities of difficult ground and support types were estimated for the Chattahoochee Tunnel using the Rock Mass Rating system. RMR classifies the ground into five categories, ranging from “very good” to “very poor,” based on five main parameters: intact rock strength, RQD, joint spacing, joint condition, and groundwater inflow. For the Chattahoochee Tunnel, these parameters were independently measured in the cores and shown graphically on the boring logs. A 55 matrix was calculated to obtain the statistical distribution of RMR for the project. Three baseline ground types were defined based on the RMR. Geologic mapping inside the tunnel during construction has verified the accuracy of this method.

Jan 1, 2003

By John A. Rumball, Martin R. Houchin

Data from autogenous and semi-autogenous tests in a 1.67m diameter mill have been analysed in terms of a new model for rock abrasion. This model defines specific rate as the rate of production of fines (material less than 13mm) per unit mass of rock, where the term “rock” is applied to all ore pieces of ore coarser than the grate size. In most cases, an allowance for preliminary rounding and cleavage was made. A method has been developed to analyse steady-state data, using piecewise fitting to the cumulative size distributions. The model was compared to the well-established models, which are based on the population balance method. The specific rate increased for all rock sizes as the volume of 100mm balls in the mill was increased. Tests using a coarser feed and smaller balls provided further evidence that once rocks are rounded, abrasion is due to localised surface damage, caused by impacts, rather than rotational shear. An allowance for rapid rounding of jagged rocks, followed by less rapid abrasion of rounded pebbles was also tested, but the analysis was not conclusive. The average specific rate is a useful measure of the capacity of a primary mill. The effect of power intensity (kW/t of ore) was also investigated as a means of extrapolating the pilot-plant data to large production mills.

Sep 29, 2003

An approximate rapid design system for tunnel liners and underground structures is presented which permits the effects of structure geometry and stiffness, rock quality in terms of its deformation modulus, and the applied system loading to be entered as data to produce direct designs conforming to stress limitations, optimum reinforcement requirements and restraints on section dimensions. An 'equivalent column' concept is introduced for modelling the rock mass in contact with the structure. Only the rock treatment is given in detail but the results of sensitivity analyses, with reference to rock quality, for a typical liner design are given and these results related to a number of empirical design approaches.

Jan 1, 1976

By Larry Taylor, Thomas Zdeb, Brian Jacobs, Dennis Jensen

Subway tunnels proposed for the Los Angeles County Metropolitan Transportation Authority (LAMTA) East Side Extension are to be excavated below the groundwater through an area of Los Angeles, California with dissolved hydrogen sulfide concentrations in excess of 200 mg/L. To address unique construction and worker safety issues, bench scale and field pilot test studies were conducted to evaluate various mitigation alternatives including in-situ oxidation by chemical injection, slurry pH adjustment to suppress H2S evolution, and chemical treatment to remove the H2S from the slurry and muck material. The results provided the basis for detailed hydrogen sulfide control specifications for the contractor.

Jan 1, 1999

By G. S. Barry

INVESTIGATIONS to date have shown that, should there be the need or the appropriate economic stimulus, Canada's mineral resources are sufficiently extensive to allow considerable expansion of its non-fuel mineral industry, during the remaining part of this century and possibly beyond (1, 2). The availability of sufficient capital will be one of the critical factors which will determine whether this potential will be fulfilled. The following analysis centers on the capital requirements of the Canadian non-fuel mineral industry under one set of basic assumptions of capacity growth, cost of new and replacement capacity, rates of depletion and depreciation of mines and plant, and the cost of exploration and infrastructure. Mindful of the fact that exploration and development will not thrive in Canada unless a very positive approach is taken, the writers make no apologies for being "optimistic" about long-term production prospects. Furthermore, in the event that world demand does escalate as anticipated and the forecast realistically attainable levels of Canadian production are not reached, then Canada will not have reaped the full range of economic benefits available, and opportunities will have been lost. Projections for Canadian production between 1976 and 2000 are essentially based on the forecast published in the 1974 paper, "Towards a Mineral Policy for Canada - Opportunities for Choice (3), with some updating on the basis of recent developments.

Jan 1, 1977

By Damien Gaboury

"Two practical methods for correlating two or more diamond-drill core intersections, using a stereographic projection software are presented. The first may be used to establish if two or more vein intersections are correlative, based on their core angles and diamond-drillhole attitudes. The second method allows prediction of main vein attitudes from numerous intersections, based on a spherical density contouring projection. The methods are suitable for: (1) correlating veins in complex orebodies; (2) ascertaining lateral continuity of ore for reserve estimations; (3) demonstrating the hidden complexity of an orebody; and (4) correlating and interpreting various planar elements.IntroductionModern mineral exploration relies on diamond- drill core data and on the ability of geologists to interpret them. Drill core generally yields unoriented information, unless an expensive orientation device is used. As a consequence, strike and dip of planar elements such as lithological contacts or mineralized veins cannot be determined easily. This is particularly true for blind deposits (covered by thick overburden) and complex orebodies, where field data cannot support drilling interpretations. Such a problem has been addressed previously using two and three diamond drillholes and several solutions were proposed based on trigonometry, and geometric and stereographic projections (Mead, 1921; Wisser, 1932; Fischer, 1941; Stein, 1941; Bucher, 1943; Gilluly, 1944; Addie, 1962; Mills, 1963; Lyons, 1964). However, these solutions are time consuming and not relevant to present day computerized data plots."

Jan 1, 1997

By W. C. Holliman

This report describes apparatus and procedure used for determining the vapor pressure of aviation gasoline in surveys of commercial aviation-gasoline characteristics made by the Bureau of Mines in cooperation with the Coordinating Fuel and Equipment Committee of the Coordinating Research Council, Inc. (CFR-CRC). The method is a modification of the Reid method, in which a mercury manor is substituted for the Bourdon-type gage of the Reid method. The method was used in earlier surveys made by the National Bureau of Standards in cooperation with the CFR-CRC, and was used in the Bureau of Mines surveys at the request of the cooperating organizations. It is designed for special research problems? particularly in vapor-lock studies, which require a precision greater than obtainable by the Reid vapor pressure method. A repeatability of + 0.01 p.s.i. average deviation from the mean may be obtained by method.

Jan 1, 1950

By Helmut Antrekowitsch

Nowadays nearly the half of the world zinc production is used for galvanizing. After their life span most of the galvanized products return as scrap to the steel mill. During the steel process the zinc is collected in the flue dust It is astonishing to notice that between 40 and 50 % of the zinc produced is brought into the steel processing cycle by the coated scrap while only 3 to 5 % of the zinc production can be covered by the recycling of the zinc-bearing steel mill dusts. Responsible for this worse ratio is the fact that the established recycling technologies suffer from high energy consumption, low zinc yields, halogen problems and hardly any iron recovery. A development of new or an optimization of current recycling procedures for the dusts is unalterable because of increasing zinc amounts in these residues and the rising costs for the disposal. Different pyrometallurgical recycling technologies are tested in rotary kilns and vertical retorts at the Department of Nonferrous Metallurgy, University of Leoben, Austria. Various reducing agents from carbon monoxide to hydrogen and combinations are used. The results should make it possible to draw conclusions that allow an economical and ecological judgement of the different varieties. The goal is to support the affected industry to increase the low recycling rate and prevent a loss of high zinc values in the steel industry filter dusts.

Jan 1, 2003

By E. J. Kloos

The Bureau of Mines developed a test for evaluating gas masks designed to protect against phosphine gas; phosphonium iodide is used as a source of phosphine. Gas masks approved by the Bureau for respiratory protection against phosphine include the GMC-SS-1, Mine Safety Appliances Co.; the LG-10 and LG-10G, Willson Products Division, The Electric Storage Battery Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By R. S. Silo

A new process for leaching oxidized copper ore (CuO) is presented. Its principle advantage is that it requires low cost raw materials. For large operations the only materials used are sodium chloride (NaCl) and calcium carbonate (CaCO3). In those operations of medium size, sulfur, which is abundant in the North of Chile, is used. However the process may also be applied to small copper plants provided low cost sulfuric acid is available as a substitute for sulfur. That is, it may be applied to those small capacity plants where large additional installations for the regeneration of the leaching solution are not needed. The method is comprised of six stages, namely: Crushing, Leaching, Washing of the Solution, Precipitation, Regeneration of the Leaching Solution, and Fusion. A flow diagram for this process in a large or medium-sized plant is given. LEACHING This process requires hydrochloric acid as the leaching solution for treating copper ores. This is easily produced from sulfuric acid and sodium chloride as follows: A small excess of NaCl is advisable to avoid the presence of free sulfuric acid. The experiments reported here were performed with 36 grams of HC1 per liter of solution to obtain a free acidity equivalent to 50 gpl of H2SO4 (the usual leaching solution concentration). Hydrochloric acid leaching may be done by either of the usual methods; i.e. percolation or agitation. The method selected depends on the characteristics of the ore. No matter which method is chosen, low pressure air can be used either as an air lift for circulation of the solution, or for agitation of the pulp with "Pachuca" tanks. In either case, there are no problems with respect to oxidation. Leaching by agitation produces good recovery; but at times, the problem of high consumption of leaching solution or the overproduction of grinding slimes which interfere with contact between phases negates this advantage. The percolation method was used in this study. Percolation took place in four 15-liter containers, 11 1/2 in. diam. by 12 in. height, having hemispheric bottoms. Each container was fitted with a wooden bottom having 1/4 in- holes. The air lift was a 3/4 in. plastic tube 10 in. high. Air at 6 psi was supplied from a rotating laboratory compressor. 10 kg of ore were charged to the container and counter-current leaching was used. The leaching solutions were fed through the center pipe in order to use the ascending solutions to reject the air in the charge. The solution circulated through the air lift in order to facilitate the movement according to the increase in density produced by the reaction between the phases present. Specific observations made in this report cannot be generalized because the leaching characteristics are dependent on the nature of the ore used, the method of leaching, and the production of primary or secondary slimes while crushing or leaching.

Jan 1, 1967

By G. A. Irdi

An automated method of microscopy for determining the pyrite size distribution on two base coals that were crushed to 28 mesh x 0 has been developed. Polished epoxy-bound coal pellets were prepared and examined by a Zeiss IBAS image analyzer utilizing a program developed from provided software. Pyrite size distribution determination is considered a necessary first step in pyrite characterization that could lead to successful predictions, by microscopy, of a coal's theoretical pyritic sulfur removal. Our research efforts to date have indicated that the IBP-S can be a reliable instrument for determining pyrite size distribution in crushed coal. A program was also developed to convert pyrite size data to a weight basis for comparisons to the results from chemical analyses. The problems encountered in our research and their solutions will be presented in the discussion.

Jan 1, 1986

By H. U. R. Kattentidt, W. L. Dalmijn, T. P. R. de Jong

"Research at Delft University aims to develop systems for automatic inspection and sorting of bulk solids which can be applied in the mineral processing and recycling industry. A recent development includes an automatic sorter based on airport X-ray inspection technology. It is designed for continuous inspection and sorting of 5 – 150 mm solids and has as objective a cost effective and high capacity on-line inspection and sorting.Dual energy X-ray transmission imaging provides instantaneous data about particle dimensions and the atomic number distribution. The system provides particle thickness and average atomic number on a pixel level at scanning speeds between 250 and 500 lines / second. With existing X-ray components inspection speeds between 0.5 and 2 m/s at approximately 1-meter inspection width and between 1.5*1.5 and 5*5 mm2 sensor resolution can be achieved.Imaging algorithms that were developed by Delft University for applications in recycling, waste cleaning and other applications acquire shape, size distribution and composition data. Currently on-line processing of a product at a rate of around 200 particles per second is possible using a standard PC. Experiments with a demonstration X-ray unit indicated good potential for various applications in solids processing. They include continuous inspection of organic content, sulphur, chlorine, ash, and metal distribution. It is applicable for coal cleaning, ore sorting, industrial minerals, and various applications within waste cleaning and recycling. Dual energy X-ray transmission fundamentals and recent progress in system development and applications are presented."

Jan 1, 2003

By Thomas Lien

Session 1 - 1 :45 p.m. June 27,1983 Session Chairman: Robert Diederich, RMCMl New Mexico Vice President MR. DIEDERICH: My name is Bob Diederich. I'm the Vice President of the Rocky Mountain Coal Mining Insitute from the state of New Mexico. I'm manager for the Navajo Mine down in Farmington, New Mexico and also project manager for a new mine that we're starling out called the LaPlata Mine in the same area. I'd like to introduce our first speaker, Tom Lien, who is the Director of Engineering, Western Division of AMAX Coal Company. He is responsible for mine engineering, environmental engineering, permitting, reclamation, planning, design and construction plant engineering, geology exploration, quality control and real estate for the western division. He joined AMAX Coal in 1980 as manager of preparation and quality control and was promoted to the present position in August of 1980. He has a BS in geological engineering from the University of Mines. He previously worked for Kennecott Copper Corporation in Hayden, Arizona from 1965 to 1970. He worked as a mine geologist, mill metallurgist, mine production and quality control engineer. Then he also worked for Kaiser Steel Corporation, Eagle Mountain Iron Ore Mine in California, 1970 to 1977. Worked as a process engineer and plant superintendent at that place. Then he was employed by Mountain States Research and Development, Tucson, Arizona, 1977 to 1980. Worked as a senior process engineer and operation superintendent. So without further ado, I'd like to introduce Tom Lien who will talk to us about in-pit coal crushing. MR. LIEN: Thank you. The official title of my paper is actually: "The Potential for In-pit Crushing and Conveying in the Powder River Basin." The Powder River Basin is one of the world's greatest coal fields and will be an important source of energy for centuries to come. About one-eighth of the total coal producing in the United States comes from the Powder River Basin, and 80% of that production came out of Campbell County, Wyoming last year. The growth potential for this region is projected to be enormous. New technology as well as existing technology will make this region competitive in the decades ahead. Understanding the current status of the Powder River Basin, both the mines and the possible methods for changing the means of material movements within the mines is the subject of this paper. Each mine is unique and must be addressed specifically with respect to the application of new and innovative technology. There have been many articles written in the recent mining journals on in-pit crushing and conveying applications, including costs which are very interesting, enlightening and I recommend it to any company considering such installations. To give a general setting, coal production in the United States for 1982 was about 800,000.000 tons. This production came principally from six regions, the Applachian fields of the eastern states where bituminous and anthracite coals have been mined for almost three centuries, the Midwest located in the upper Mississippi Valley are often typified by huge dragline operations of which AMAX Coal has three right now, the Gulf Coast lignites. feeding mine-mouth power plants, the vast bituminous and sub-bituminous departments of the four-comer states of Arizona, New Mexico, Colorado, and Utah and finally the Northern Great Plains lignite fields currently being developed and the sub-bituminous fields of Wyoming and Montana including the Powder River Basin. The Powder River Basin is located in northeastern Wyoming and southeastern Montana. It is the darker brown right in the center of the photograph. It covers about 18,000 square miles. It's about 200 miles north to south and 90 miles east to west. The shallowest coal beds are on the east, north and northwest edges of the basin with deeper coal beds toward the center in the same kind of relationship. There are about one trillion tons of coal in the Powder River Basin, that's the one with 12 zeros after it. A little bit there. It's distributed in many, many seams at varying depths to the current topography. In 1982 about 100,000,000 tons of coal were mined from this basin and 81,000,000 tons came out of Campbell County, Wyoming. The mines that are shown in this picture are basically the mines around the basin edge. The principal area that I'll be talking about is the eastern edge down where it shows Gillette and Campbell County. Geologically the Powder River Basin is the Fort Union formation. The most productive seam is called the Wyodak or Smith-Roland or the Anderson-Canyon, depending upon where you're located. There is about 75 billion tons of coal in the Wyodak of which about 23 billion are considered surface minable today. the coal is Paleocene in age, about 40,000,000 years old. It was once an old Delta region very much like the Mississippi River delta is today. During the 100,000 years that this deposit was formed peat accumulated to a thickness of about 365 feet. It was later buried and turned into sub-bituminous coal. All of the coal mined in the basin is for the electric utility industry. This coal has a typical BTU content of about 8,300 plus or minus about 4,500 BTUs. Sulfur coal is generally less than'/ %, thereby making this coal compliance coal in terms of sulfur dioxide emissions, 1.2 pounds of sulfur dioxide per million

Jan 1, 1983

By K H. Esbensen

Optimisation of a real-time at-line monitoring system for control of industrial granule coating quality is presented. The system is based on a fluorescence imaging system, because fluorescence originates in the interiors of enzyme granules but is significantly quenched by a polymer coating (which is needed due to environmental precautions). We have developed an image analytical system for direct prediction of coating quality, which is based on application of the Angle Measure Technique (AMT) for image complexity characterisation; AMT is briefly described. The first part of the presentation addresses pixel sampling strategies within a digital industrial image, inherent in application of AMT, in which the unfolded image is regarded as a one-dimensional object in analogy with 1D process sampling in Theory of Sampling (TOS). The effects of random, stratified and systematic pixel selections in the unfolded image are evaluated. Also factors such as the fraction of image pixels and the effects of specific unfolding strategies (there are three principal strategies, termed æchopÆ, æsnakeÆ and æspiralÆ respectively) are investigated. It turns out that unsuspected artifacts are sometimes produced, related to the specifics of the unfolding procedure, which interferes with a straightforward 1D TOS process sampling analogy. These artifacts have a wider interest û among others, for 2D sampling û and therefore receive special attention in this presentation. The optimal pixel selection strategy for the AMT algorithm is found to be systematic or stratified sampling (not surprising according to TOS) of 500+ initiating points, but need to be unfolded in the novel spiral- or snake-wise fashions in order to effectively counteract these artifacts. This also has a general impact on various suggested standard schemes for 2D grid-sampling, among others, from the geoscience realms. The second part of the presentation is directed towards optimal image analytical sampling of a continuous series of fluorescent images (imaging of conveyor belts of æinfinite lengthÆ), ie optimisation of process image sampling. The minimum number of images needed to uphold a sufficiently good on-line estimate of the quality control (QC) parameter in question is found to correspond to the relatively high sampling rate of 15 - 20 per cent, which can be shown to be related to an intrinsic very high measurement error level (25 per cent) of a mandated analytical reference method.

Jan 1, 2005

By M Wortley, A Cantarutti, T Ozkocak

The estimation of the grinding mill charge weight is vital to ensure its efficient performance. Mill underloading or overloading can cause losses through decreased production or unplanned down time. Metso Minerals Process Technology Asia Pacific and South America (MMPT) has developed two systems for measuring mill load. The first is an acoustic system (SmartEarÖ) and the second is an online model-based charge estimation system. The aim of both systems is to facilitate better operation of grinding mills. SmartEarÖ performs analysis on an audio signal from the mill and allows each different frequency component to be viewed, analysed and used in process control for load estimation. By isolating different frequencies, SmartEarÖ can give an estimate of mill load. The online dynamic mill model uses measurable mill parameters (such as power) to predict the current total load. Kalman filtering can also be utilised to further increase the accuracy of the model. Both of MetsoÆs systems have been installed at BHP BillitonÆs Cannington mine to measure the load within their autogenous (AG) mill. In this paper, the methods of mill load estimation are reviewed and compared to the bearing pressure reading, which is the current method used by Cannington to control mill load. The redundant estimates of mill load provide increased confidence and consequently more robust grinding operation under a wide range of conditions.

Jan 1, 2008

As fulfillment of the requirements of Contract H0387019 for the United States Department of the Interior, Bureau of Mines, a complete field kit, for performing on-site determinations of individual employee Time Weighted Average (TWA) exposures to nitrogen dioxide (NO2) and nitric oxide (NO), has been developed by MDA Scientific, Inc. This report provides background information and experimental data validating the use of this kit with confidence to ? 10 percent accuracy.

Jan 1, 1981

By Christopher R. Davis

Resource modelling is the basis for any economic appraisal of a mining project and includes a number of steps from data acquisition and validation to resource reporting and classification. At each step in the modelling process it is necessary to define the specific objectives, the methodology proposed to achieve those objectives and to establish a set of checks and validation tools to assess the effectiveness of the proposed methodology. The data used has to be both reliable and relevant for the purpose of the modelling. QA/QC for database validation requires verification of sample location; including correct collar location, topographic modelling and down-hole surveying. Validation is also performed on assaying information such as checks for sampling bias and accuracy of core splits, proper use of pulp duplicates and standards, handling of calculated values, explicit/implicit absent data and data entry errors. The second step involves identifying the mineralized domains resulting from the mineralization process. This step requires a geometric interpretation of all relevant geological features that have influenced the spatial distribution of the mineralization including dykes, faults and alteration. In addition, a geologic reference system rather than a standard Cartesian system is established to measure distances between samples. Once the mineralized domains are established and the database has been validated, statistical and spatial description of the mineralized samples are examined in order to establish the histogram and the variogram of all variables of interest and their correlation. Results are also used to calibrate the global resource estimate within the mineralized domain and to establish the search strategy for grade interpolation. The mineral envelope is filled with polyhedral cells representing mining blocks. The average grade of these blocks is estimated using kriging techniques in order to eliminate global bias and to minimize the local error in the block grade estimate. Visual checks are made to validate the spatial trends in grade distribution while global bias and smoothing effect are assessed from the declustered sample statistics. When required, smoothing correction may be applied using ?change of support? techniques. Simulations are used to perform sensitivity analysis and the simulation models are used if severe smoothing of spatial variability makes the interpolated model inappropriate for mine planning. The keys to successful resource estimation are an integrated team of geologists, geophysicists, geostatisticians and mine engineers using the best available technology and reviews by independent auditors. The resource team is also responsible for performing a QA/QC program in order to measure the effectiveness of the methods in meeting the specific objectives at each step of the modelling process.

May 1, 2001

By Haukka M. T

A new low-dilution fusion method which has been successfully used for accurate determination of the major oxide components of silicate rocks, is applicable to rapid, accurate determination of trace or minor eiements in mineral exploration samples. Limit of detection is in many cases less than 5 ppm. Either rapid, approximate measurement and calculation methods (suitable for geochemical exploration), or more accurate methods (applicable to orebody evaluation studies) may be used.Rapid methods are described for nickel in rocks and sulphides containing 10 ppm to >2 per cent Ni, and for gallium. The rarely-determined element gallium is an example of a constituent which may be easily investigatedby XRF using the LiB02 fusion disc, which is a permanent, easily-stored analytical sample available for later rapid or accurate analyses. The method is applicable to over 30 elements at levels encountered in mineral exploration.

Jan 1, 1978

By W. K. Sawyer

In this Bureau of Mines investigation, one-and two-dimensional gas reservoir simulators were combined in such a manner that pressure distributions both in an induced vertical fracture and in the surrounding formation, could be determined as a function of time for any specified well production rate. The technique used consisted basically of the alternate ust of one-and two-dimensional algorithms for obtaining new pressure distributions in the fracture and in the reservoir, respectively. The pressures at adjacent reservoir and fracture nodes were used to calculate flow rates from the formation into the fracture, which provided source terms for both algorithms. The combination model developed provides the only known means of simultaneously simulating transient gas flow in a vertical fracture and the surrounding formation. Thus, the technique developed would be useful in locating wells in a gas storage field in that the effects of both fracture length and conductivity could be considered prior to drilling and fracturing operations. In addition, it will be helpful in analyzing pressure drawdown tests in a vertically fractured gas well since the entire test can be readily simulated for a wide range of reservoir and fracture properties.

Jan 1, 1974

The uptake of zinc, lead, and copper by the flora of the Tui Base Mine area near Te Aroha is described.Vegetation and soil samples were taken from two traverses across the Raukaka Lode. Results. after statistical analysis, indicated that Beilschmiedia tawa was a suitable species for biogeochemical prospecting for lead and that SchefJlera digitata was satisfactory for zinc.The tawa showed a negative anomaly for lead over the vein itself but not over the adjacent dispersion halo. It was concluded that lead concentrations greater than 230 p.p.m. in the wood ash of the tawa and zinc concentrationsgreater than 540 p.p.m. in the leaf ash of S. digitata denoted threshold values for anomalous mineralization in the soil beneath. Although both species contained copper, neither indicated a soil anomaly for this element.

Jan 1, 1969