Search Documents

By Errol L. Montgomery

The region of metalic ore deposits in northern Chile, southern Peru, western Bolivia, and northwestern Argentina occurs in arid zones at altitudes as high as 4,600 meters. Because surface water supplies are meager, new mines require unexploited sources of water. Prolific groundwater aquifers occur in salar basins in this region of the Andean Highlands. Exploration water wells have been constructed and aquifer characteristics have been tested in eight salar basins. Results indicate groundwater quality is good. Aquifer transmissivity and storage computed from results of pumping tests indicate maximum production water well capacities in excess of 170 liters per second.

Jan 1, 1982

By RB. Pedersen, T. Barryere, E. Reeves, A. Stensland, I. Thorseth, T. Baumberger

Venting on ultraslow spreading ridges is far more abundant then previously predicted, and the discrepancy between observed and predicted vent field density may imply that non-magmatic heat sources are common along these ridges (Baker and German, 2004; Escartin et al., 2008; Rona et al., 2010; German et al., 2016). In this study we have estimated the flux from two hydrothermal vent sites situated on the slow to ultraslow spreading Mohns Ridge at the Arctic Mid-Ocean Ridge system (AMOR). The flux estimates have been made using the primordial isotope 3He in the non-buoyant plume above the Loki’s Castle vent field at the northern termination of the Mohns Ridge, and from the Jan Mayen vent fields area situated close to the southern termination of the ridge. Primordial 3He enters the oceans through degassing and mixing with hydrothermal fluids eventually to be discharged at the ocean floor primarily at hydrothermal vent sites and submarine volcanic eruptions (e.g. Clarke et al., 1969; Lupton and Craig, 1981; Lupton, 1998). Once introduced into the water column the concentration will only decrease by dilution due to its conservative behavior in the water column. Water column samples were collected using a CTD (conductivity, temperature, depth) probe (911plus Seabird) with a Niskin water bottle rosette. The water column above the Jan Mayen vent fields (JMVF) was sampled in the years 2006, 2011, 2012 and 2013 (82 samples) and the water column above the Loki’s Castle vent field was sampled in the years 2007, 2008 and 2009 (116 samples).

Jan 1, 2018

By Prakash Venkatesan, Yongxiang Yang, Seshadri Seetharaman, Aida Abbasalizadeh, Jilt Sietsma

Electrolytic production of metallic neodymium is carried out in fused fluoride salts containing neodymium oxide. Two major challenges pertaining to neodymium production are (a) low oxide solubility and (b) possible fluorine gas evolution. A novel iron-based reactive anode is proposed and tested to overcome fluorine gas evolution during electrolysis of neodymium oxide in molten fluoride salts.

Mar 1, 2017

By Gary Peach, Khalid Saif Al-Khayareen, Vigil Fernandez, Furqan Hameed

The Musaimeer pump station and outfall project (MPSO) is in Doha Qatar. This technical paper will discuss and explain the three major stages of geotechnical investigation employed. Stage one the tender geotechnical data and how this was used to design the TBM and identify various areas of risk. Stage two was the selection of supplementary geotechnical investigation methodologies. Stage three was the geotechnical investigation by specialist equipment installed on the TBM and providing further data on a real time basis as the TBM was advancing. Analysis of all the data will be provided along with the lessons learned.

Jun 23, 2024

By Jung-Joo Kim, Jong-Uk Kim, Turab H. Jafri, Han-Kyu Yoo

"INTRODUCTION Steel sets such as H-type and lattice girders are often installed in the tunnels before the hardening of shotcrete to ensure the stability of conventional tunnels in soft ground conditions. In practice, while designing the tunnels with the help of numerical analysis, steel sets are generally considered only as temporary support elements. Only a few studies propose the direct application of composite support in the tunnel design, based on large-scale experiments and numerical analysis. In order to assess the structural performance of the composite support consisting of shotcrete and steel sets, large-scale experiments were performed on two types of arch-shaped specimens by applying the combined effects of axial forces and bending moments. Based on the experimental results, numerical analysis was performed to assess the application of composite support in tunnel design. The crown settlement, axial forces, bending moments, and load distribution in the composite support were analyzed in the light of different structural patterns. LARGE-SCALE EXPERIMENTS USING COMPOSITE SUPPORT Preparation and Procedure of the Experiments The preparation setup as well as the organized procedure of the large-scale experiments using composite support is shown in Figure 1. An appropriate geometry of the specimens was selected by considering the standard cross-section of a two-lane highway tunnel in South Korea. Under the loading conditions meant to develop the axial forces and bending moments simultaneously, arch-shaped specimens were assembled with the ends of the specimens subtending a 60° arc angle at the center of the arc circle as shown in Figure 2. The fabrication of six specimens was completed in two groups based on the dimensions of steel sets, with the first group of three specimens being reinforced by H100 (No.1, No.2, No.3) and the other three by H125 (No.4, No.5, No.6). In order to reduce the voids on the boundary of the shotcrete and steel sets, concrete was casted over the steel sets instead of using shotcrete. The specimens were designed to incorporate the uniaxial compressive strength of 21 MPa. Shear keys and steel plates were installed at the ends of the specimens, so that shear failure could be avoided at the ends and the specimens could also be protected from detachment at the fixation. Translational and rotational movements at the ends of specimens were fixed."

Jan 1, 2016

By Peter Van deVelde

Many companies in North America because of economic or environmental reasons are considering reprocessing material from their waste ponds. The Japanese have developed highly specialized machines and techniques to reprocess industrial/mining wastes from settling ponds. This paper discusses the techniques and results of applying this technology to North American applications.

Jan 1, 1983

By Robert H. Richards

Jan 1, 1883

By G. Bjorling

After complete dissolution of chalcopyrite concentrate in sulphuric acid in presence of nitric acid the excess of the latter is expelled by a surplus of concentrate and the last traces of nitrate removed in the mother liquor after crystallization of the copper and iron sulphates. Zinc accumulates in the mother liquor from which it can be removed by solvent extraction of zinc sulphate as a pair of ions. After dissolution of the sulphate crystals in water the neutral solution is oxidized in an autoclave at 140°C where iron sulphate is thermally hydrolyzed; the iron-free solution is taken to copper electrowinning and the cell acid after partial evaporation recirculated with the mother liquor to the leaching circuit. Total recovery of copper is about 96%; other metals like zinc and iron are concentrated in industrially usable products. At a copper price of about 70 c/lb, the method appears to be profitable also in a small unit.

Jan 1, 1976

By T. Newton, G. A. Bezuidenhout, P. J. Tauetsile, F. Trask

The technology to selectively leach gold, silver and base metals from ores, concentrates, and wastes, using an alkaline glycine solution, has initiated significant interest in using the new technology in various environments such as in-situ, in-place, dump, heap, and vat and agitated tank leaching. It has been shown that glycine acts synergistically with a number of other lixiviants to lower the net consumption of the other lixiviants while allowing low cost glycine solution recovery. Glycine is a non-toxic, stable, environmentally benign reagent that is available in bulk industrial quantities. It has the ability to dissolve most copper oxide and sulfide minerals, as well as native copper, whilst not interacting with acid consuming gangue nor dissolving iron and various or ubiquitous gangue elements. It acts synergistically with small amounts of cyanide to leach gold-copper ores at leach rates higher than either glycine or cyanide on their own, while significantly reducing cyanide consumption and eliminating detoxification requirements. The leaching behaviour of various glycine based systems will be reviewed, followed by the evaluation of the adsorption of gold onto activated carbon. Where the economics merit it, copper can be easily recovered using solvent extraction or sulfide precipitation.

Jan 1, 2017

By Rick T. Richins

Despite what may be overwhelming evidence that natural degradation of cyanide and cyanide attenuation in hydrogeochemical processes are capable of reducing or eliminating potential water quality problems associated with heap leach facilities, the recent sharp increase in the price of gold and wide interest in the cyanidation process has focused all regulatory eyes on cyanide leaching. Regulations continue to increase, design criteria are more strict, and detoxification requirements approach or exceed the level of detectability. Current governmental regulation of mining and milling operations using cyanide varies considerably from state to state. The lack of regulatory consistency at this level is largely attributable to the current Bevill Amendment exclusion of mine wastes as potentially hazardous wastes, the undefined status of the Environmental Protection Agency's ongoing mine wast study effort, and the mining industry's reluctance to develop a consistent policy regarding state versus federal mine waste regulation.

Jan 1, 1998

Reduce haulage truck accidents resulting from blind spots, with a special emphasis on reducing accidents during backing operations.

Jan 1, 1997

By Igor E. Mikhaltsev

The goal of investigation of the midwaters and of the bottom of the world - ocean versus technological possibilities. Manned vehicles and maximum depth decision. The methods of solving of the problem. The science and technology alloy. Mutual venture of Academy of Sciences of the USSR and, Rauma-Repola Oy of Finland. MIR-1 and MIR-2 - as twins. No reasons of copy "Sea Cliff" and "Nautilus". Six landmarks of specificity of "MIR"-type submersibles. The manned spheres and three ballast spheres are made of maraging steel; the electric power resource (100 kwh) and maximum underwater speed (5 knots) is two times more than of the analogous vehicles while the batteries are of NiFe type; the MIR submersibles have the seawater ballast (and trim) system which means practically unlimited vertical manoeuvrability ; and the weight in air is equal to "Nautilus" - 18,6 tons (in case of equal energy resource the weight of MIR-1 or MIR-2 would be 17 tons). Some remarks on standard life support (248 man-hours) safety systems and specificity of launch & recovery system.

Jan 1, 1988

By S. Glen

Cyanide management practices on modern gold plants are becoming more onerous, due to environmental pressures, particularly for signatories to the International Cyanide Management Code. Operations are therefore seeking to reduce levels of weak-acid dissociable (WAD) cyanide reporting to spigot discharge as well as to any eventual discharges from the tailings storage facility (TSF). Current gold industry standard processes primarily include the oxidation of cyanide by means of sodium meta-bisulfite (SMBS, or SO2) with air, Caro&apos;s acid (H2SO5) or hydrogen peroxide (H2O2). These processes require the transport and usage of expensive oxidizing reagents, along with the safety and environmental issues associated with these corrosive and toxic chemicals. Maelgwyn Mineral Services (MMS) has developed the MMS CN-DTM process, which utilizes the Aachen ReactorTM, a high-energy mass-transfer superoxygenation system, in conjunction with an activated carbon-based catalyst and no additional reagents, to increase the rate of cyanide oxidation to cyanate, the thermodynamically more stable form. Testwork conducted at the Maelgwyn Australia testwork facility in Perth Australia is described, at both pilot scale and continuous bench-scale, on a sample of tailings effluent obtained from an Australian gold plant. WAD cyanide is demonstrated to be lowered using the MMS CN-DTM process from an influent of 130 mg/L to the required levels for discharge to TSF (<50 mg/L). The continuous test results showed stable operation over three residence time turnovers. The pilot-scale results demonstrated the efficiency of the process at the reasonably large scales required for engineering cost estimation.

Jan 1, 2011

By Shangshu Li, Xionggang Lu, Xingli Zou, Zhongya Pang, Kai Zheng, Yinshuai Wang

Metal carbides (MCs), especially transition metal carbides have attracted a lot of attention due to their unique properties, such as high strength and hardness, good chemical and thermal stability. In this paper, a new route was proposed for preparing TiC nanoparticles directly from TiO 2/C precursor by using solid oxide membrane (SOM) technology in molten CaCl2. The TiO2/C pellet pressed under 8 MPa was used as the cathode, and a yttria-stabilized zirconia (YSZ) tube filled with carbon-saturated liquid tin was served as the anode. This process employs an inert SOM to separate the anodic reaction area from the molten electrolyte to control the electrolysis process. The electrochemical process was carried out in molten CaCl2 at 1000°C and 4.0 V from 0.5 to 4 h. The characteristics of the phase composition and morphology of the electrolysis products were investigated. The product electrolyzed was examined by X-ray diffraction (XRD) and scanning electron microscopy (SEM) with energy dispersive spectrometer (EDS). The results show that TiC nanoparticles can be obtained directly from TiO2/C mixture at 1000 °C, 4.0 V and for 4 h in molten CaCl 2 and the current efficiency is calculated to be 74.1%. In conclusion, we suggest that the SOM process is a promising environmentally friendly and low energy costs electrochemical method for the facile and controllable electrodeoxidation of MO x/C precursors to micro/ nanostructured MCs.

Mar 1, 2018

By Denys Parra, Ernesto Nájar, Javier Mendoza

La mayoría de unidades mineras o proyectos mineros en el Perú se localizan a lo largo de la cordillera de los Andes, donde las condiciones del relieve del terreno en algunos casos, hacen difícil la tarea de encontrar áreas con la suficiente capacidad para almacenar relaves convencionales (pulpa o espesados). En otros casos existe la necesidad de recuperar la mayor cantidad de agua, impactar la menor cantidad de área o la escasez de espacios para desarrollar proyectos de instalaciones de almacenamiento de relaves. Bajo estas condiciones la disposición del relave filtrado representa una buena alternativa para el almacenamiento de relaves en varios proyectos mineros.

Sep 1, 2017

By A. J. Carlson, G. M. Marincel, M. L. Hovland, J. H. Healy

Research personnel of Erie Mining Co., a pioneer taconite mining firm on the Mesabi Range, have invented a new method to make an effective 325 mesh separation at high tonnage rates over stationary screens. The company regards this development as historically significant in that it represents the first successful method to commercially screen large tonnages of ore at fine sizes. Erie, which is now completing an expansion program at its plant site near Hoyt Lakes, Minn., has incorporated this screening method as part of that expansion. When completed, the concentration plant will produce 10.3 million tons of iron concentrate, all of which will have been efficiently screened at 325 mesh.

Jan 4, 1967

By G. Shore

Radiation grafted structures my be fabricated to contain ion exchange groups selective to an ion complex. Proper choice of substrate and monomer will provide selective ion exchange with differing physico and chemical properties. Grafting a selected monomer to the proper polymer will provide selective ion exchange with assured chemical protection of the substrate. Ion exchange systems utilizing radiation grafted structures have been fabricated to ''capture'' gold, silver and palladium from dilute solutions. Other ion exchange systems can feasibly be produced to remove other precious metals. Rotating Cathode Technology is used to recover the metals from their regenerating solutions are pure metal foil.

Jan 1, 1985

By Jack Craft

Local Environment Atmospheric conditions (or lack thereof) Drilling fluids are impractical Cuttings removal is a major concern Heat dissipation is a major concern Some tried-and-true mechanisms need air to function properly Gravity Low gravity means low downforce Microgravity means even less downforce Regolith Local dust may be highly abrasive Packaging for Spaceflight System mass is highly constrained The drill must fit within the spacecraft?s launch envelope Power is constrained

May 1, 2013

By Tong Deng, Yun Ma

Gold-copper ores have become important gold resources (von Michaelis, 1989), but the gold extraction from such materials posed a challenge due to the detrimental effect of copper species on gold cyanidation. Ammoniacal cyanidation process was rec­ommended (Muir et al., 1989) and practiced (Castello et al., 1992) for gold extraction from the gold ores which contain cop­per at moderate level mostly in form of oxide. This paper pro­vides an example to apply the ammoniacal cyanidation process to processing such a copper bearing gold ore.

Jan 1, 1996

By M. J. Adam

The U.S. Bureau of Mines has investigated the partitioning of complex minerals to simpler phases using sulfidation reactions for selective extraction of mineral values. This report describes research in which thermal processing of the complex Ti-bearing mineral ilmenite (FeTi03) resulted in partitioning of the valuable Ti metal to the simpler compound rutile (TiO2). Samples of ilmenite were blended with elemental S for thermal treatment at various temperatures under controlled atmospheres in an effort to dissociate the Fe from the ilmenite complex. Product characterization revealed that the Fe was partitioned &apos;from the ilmenite, forming a rim of pyrrhotite/pyrite (FeS/FeS2) on a rut il e core. The products were agate milled and then subjected to cursory magnetic and flotation techniques in an attempt to physically separate the partitioned phases. Partitioning results and phase concentration data are reported relative to thermal treatment variables and physical separation techniques.

Jan 1, 1991