Search Documents

By Qingguo Xue, Jingsong Wang, Yingli Liu, Guang Wang

In the dropping zone of blast furnace (BF), primary slag absorbing ash of pulverized coal and coke become to be intermediate slag. Due to viscosity and surface tension of slag and the pore between cokes, some slag remained in coke layer and affected the permeability of blast furnace. The flow behavior of slag with different basicity (0.55–1.10) and Al/Si (0.35–0.50) were studied. Meanwhile, the viscosity and surface tension of slag were calculated. The results showed that, with the increasing basicity of slag, surface tension increased and viscosity decreased. With the Al/Si increase, surface tension and viscosity increased. The smallest pore that all slag can pass through was 4.5 mm. However, the height between slag droplets and the bottom of crucible indicated that the ability of slag to pass through pore were weakened with the increasing basicity and Al/Si. Thus, slag which absorbed ash from fuel become difficult to pass through coke layer.

Mar 1, 2017

By Shusen Cheng, Kun Yan

An elastic-plastic stress mathematical model of hot blast stove shell has been established in order to investigate the stress distribution and deformation of the shell. The results show that stress concentration happens along the intersection line of hot blast stove body and the hot blast manifold. The plastic deformation occurs on the hot blast outlet in blast period. The deformation degree of the hot blast shell near the blast outlet in blast period is much larger than that in combustion period. In blast period, the shell near the blast outlet elongates along the horizontal direction and shortens along the vertical direction, the shell near the outlet deforms into an oval. And in combustion period, its deformation isn’t obvious. The repeated deformation of the shell near the outlet between different periods may cause the refractory brick damage and be harmful to the long campaign life of hot blast stove.

Mar 1, 2017

By D J. Williams

Tailings management is typically constrained by many factors that are taken as given. These include the tailings production rate that must be accommodated, the desire to deliver the tailings cheaply and easily as a slurry using centrifugal pumps, and a tailings footprint limited by the desire to minimise capital costs leading to a rapid tailings rate of rise and a low settled density. Other constraints include wall raises being delayed due to limited capital, inadequate tailings water and rainfall run-off management, and the net present value (NPV) approach to capital expenditure that puts off expenditure at the expense of performance. All of these constraints result in the tailings occupying much more volume than is necessary, being difficult to rehabilitate, and not being capable of supporting a beneficial post-mining land use or function. Ultimately, such constrained tailings storage facilities will assume very large dimensions, but each will typically be developed as a series of smaller storages that are filled rapidly and added to progressively. The optimal stage to efficiently recover process water is in the process plant, but this is limited by the desire to use centrifugal pumps rather than the more costly positive displacement pumps, which also require greater management of tailings deposition. Process water can also be recovered from the tailings storage facility (TSF) decant. Tailings water that is not recovered from the plant or the decant will be lost to entrainment within the tailings, seepage to the foundation or through the wall, or evaporation. However, tailings water is not always suitable for reuse in the plant, particularly when it becomes contaminated by the processing, and it may simply be stored on the TSF. This will exacerbate the seepage of contaminated water to the environment, and will limit the densification of the tailings that would otherwise occur due to desiccation of the tailings on exposure. If a larger tailings footprint were developed early, cycling of tailings deposition in thin lifts between a number of cells could occur, maintaining the dormant cells dry to enhance desiccation and densification, and ultimate rehabilitation. The end result would be a much reduced stored volume of tailings, the potential for upstream raising, and ease of rehabilitation to a high level. The higher initial capital cost would be overtaken by reduced ongoing capital, operating and closure costs.CITATION:Williams, D J, ?2014. An alternative whole-of-life approach to tailings management, in Proceedings Life-of-Mine 2014 , pp 285–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By D. D. Hogarth

"Edward Haycock, Engineer and Public Contractor Edward Haycock was born in Shrewsbury, England, June 14, 1813. His father was John Haycock, a timber merchant and soap manufacturer, residing at Swan Hill Court, Shrewsbury, and his mother Esther was the daughter of William Hilton of Hempstead, Hertfordshire. Edward's paternal grandfather, John Hiram Haycock, was the first of a line of architects that ""changed the face of Shrewsbury"" and ""provided some of the best examples of typical Victorian architecture in Shropshire""(1). Nothing is known of Edward's early life or education, although it appears that he made no attempt to follow this artistic trend. In 1833, Edward immigrated to Canada. The following year, he married Mary Butler, daughter of Johnson Butler, a Lieutenant-Colonel in the Lincoln Militia during the War of 1812. Mrs. Haycock, as co-heiress of Johnson Butler's estate, was assigned 600 choice acres of farmland in Brooke Township near present-day Sarnia. This alone would have guaranteed a tidy income, but the Haycocks soon disposed of this land, the last lots being sold in May 1840. Instead, Haycock turned his hand to engineering and, for a number of years, was employed by the Great Western Railway first in Woodstock and later in Hamilton. He then moved to Port Hope, tried farming, worked in the engineering office of the Port Hope, Lindsay and Beaverton Railway Company, and later constructed a portion of this railway(2). During his stay in Port Hope, Haycock met his future partners Ralph Jones, a contractor, and Thomas Curtis Clarke, chief engineer with the P.H.L. and B. Railway Company. The alliance was styled Jones, Haycock and Company and their most successful venture was the construction of the Government Buildings in Ottawa. This work was the crowning achievement of Haycock's career and, no doubt, his proudest moment was at 11:30 a.m., April 2, 1860, when his daughter Mary Emily, then a little girl of 4, with a special silver trowel ceremoniously laid the first stone. Of special interest in this project were the quarrying operations, which introduced Haycock to the art and difficulties of mining as well as to the potential returns of mines. Sandstone, for facing, was drawn from four quarries, 10 to 12 miles from the Departmental Buildings. Haycock seems to have been in charge of these operations, which in the early stages involved an average labour force of 86 men and 43 teams. However, by 1861, quarrying had declined in importance and the contractors were able to concentrate whole-heartedly on the construction site."

Jan 1, 1999

By H. Kim, R. W. Plummer, T. J. Stobbe

"The probability of developing coal workers' pneumoconiosis (CWP) varies among miners in different geographic areas, coal seams, and jobs. Many studies have revealed the correlation between mineral content and the frequency and severity of CWP development still remains controversial. Furthermore, the mineral content and its variability in different areas is unknown.Since mineral content is expected to vary from location to location within a mine, between mines, between coal seams, and over time, this information will be valuable in understanding the variations in CWP incidence, as well as in establishing the appropriate kinds of dust to use in toxicological research programs studying CWP.Size-selective airborne dust samples were collected using 4-stage cassette impactors at 9 different locations in each of five coal seams. These coal seams were the Upper Freeport, Pittsburgh, Kittaning, Coal Burg, and Pocahontas. Mineralogical analyses were done by a x-ray powder diffraction photographic technique.Common minerals found in coal mine dust were illite, calcite, kaolinite, quartz, siderite, dolomite, gypsum, anhydrite, and pyrite. The distribution of minerals in interand intra location samples will be reported. Early results on the mineral content show wide variations between locations.in a mine and between coal seams, and small, but significant, variations between particle sizes.INTRODUCTIONIn spite of its long history of incidence, and the large amount of research conducted on it, coal workers' pneumoconiosis (CWP) is still prevalent among coal miners and needs further research to develop effective preventive and remedial measures. Although the dose-response relationship between simple CWP and coal mine dust has been established (1), the causal agent(s) and the mechanism(s) involved in the progression of simple to complicated CWP are not yet defined. Many plausible hypotheses have been made to explain the mechanisms involved in the disease progression however none of them is satisfactory. In addition, the source of variation in occurrence of CWP among miners in different geographic areas (2), rank of coal seam (3,4), and job (5) remain unsolved."

Jan 1, 1988

By Richard L. Jenkins

Systematic sampling, in reconnaissance fashion, of the continental shelves of the United States to define favorable areas of offshore mineral deposits, is one of the long-range marine mineral; programs of the U.S. Department of the Interior. In mid-1966 the Department of the Interior launched its Heavy Metals Program to stimulate domestic output of gold which is in serious short supply. The program is jointly conducted by the Geological Survey and the Bureau of Mines.

Jan 1, 1968

By A. J. Getz

The paper reviews the status of the major precious metals projects in Australia, Papua New Guinea, Indonesia, the Philippines, and New Zealand. The projects may be at the stage of exploration, development, operation, or expansion. The paper covers project location, reserves, method of resource exploitation, anticipated production, and other unique conditions.

Jan 1, 1990

By V. Tsyplakov

This article reviews factors of preg-robbing effect, occurring in the course of pressure oxidation of ore and concentrates, containing chloride compounds and so-called 'organic carbon'. The article also summarizes the main results of the studies and testwork conducted to overcome this effect. The following efficient preg-robbing mitigation methods have been noted: higher temperature of pressure oxidation process, preliminary removal of natural carbonaceous material from concentrate, chloride removal prior to concentrate pressure oxidation, and addition of water-soluble organic blanking agents, which suppress the adsorption activity of the native ore adsorbents. Keywords: preg-robbing, double-refractory gold concentrates, pyrite, arsenopyrite, blanking agents, pressure oxidation, autoclave leaching

Sep 1, 2012

By Steven Richardson, E A. Cameron, Reza "Ray" Jambakhsh

This paper outlines the design and implementation of a method to use Long hole Carbide drilling to blast an "Upper Blind Slot Raise" in the range of 12m (40 ft).

Jan 1, 1992

By PAULL. BROUGHTON

Commercial deposits of sodium sulphate are harvested from alkaline lakes that are widespread throughout semi-arid southern Saskatchewan and adjacent southeastern A lberta. Concentration of sodium sulphate occurs in undrained basins under semi-arid conditions. Precipitation runoff from land adjacen1 to 1hese basins leaches 1he mineral from the soils and carries it in solu1ion 10 the basins. The process may be largely subsurface, wherein spring seeps feed basins associated with buried (preg/acial) river valleys. Evapora1ion during summer concentrates salts in the brines, and chilling of water below sa/Uration poin1 during win1er resu//s in deposi1ion of sodium sulpha1e (mirabili1e) crystals on lake bo//oms. Sodium su/pha1e, commercially known as sa/1 cake, ranks second only 10 po1ash in cen1ral-wes1ern Canada's nonme1allic mineral production. // is recovered from su,face brines, directly from intermittenl salt beds, and, until recently, by solution mining of shallow subswface deposits. Sodium sulphate is extrac1ed from seven alkaline lakes and sail f/a1s in Saska1chewan and one in Alberta. Annual produc1ion is approxima1e/y a halfmillion tonnes. Manufacture of kraft paper is the mos1 significanl marke1 for salt cake, but addi1ional quantifies are used in the glass and detergent manufac1uring indus1ries.

Jan 1, 1984

By P. Henry

A novel electrochemical cell has been developed for the recovery of MnO2 from residue of pyrolusite ore leading loaded with Fe, Al Ni, Co and Si impurities, This new process can be considered as an alternative to the traditional methods : S02, H2O2 or bioleaching. It has been observed to proceed fairly rapidly and could prove to be a more economically viable process, as well as being more environmentally acceptable. Electrochemical characterization and kinetic studies have shown that MnO2 is effectively leached by electrogenerated ferrous ions at high current density from a pulp containing less than 5 g8 Fe. The chemical reactions are : Cathode (inox) : 2F23+ + 2e ? 2 Fe2+ Bulk: MnO2 + 2 fe2+ 4H+ ? Mn2+ + 2 Fe3+ + 2 H2O Anode (Pb-Ag) : H2O ? ½ O2 + 2H+ + 2e Global: MnO2 +2H+ Fe2+ = Mn2+ + H2O + 1/2 O2 The catholyte (MnO2 pulp) circulates upward in the expanded mesh cathode separated from the sulfuric acid solution anolyte by a separator which shows high mechanical resistance, low porosity, low potential drop, and reasonable cost. Laboratory and mini-pilot tests have led to the construction of an OT crating pilot plant (100 kg/hr) able to leach more than 95% of Mn, Ni, Co at 1000-1200 A/m2, 50°C with high faradic yield (> 95 %) and low power consumption (3.2 kWh/kg kWh/kg &4D). New applications like the treatment of spent Zn-Mn batteries, polluted soils, spent catalysts and oxide ore (cobalt, nickel) with electrogenerated redox species are now investigated at a laboratory and mini-pilot scale.

Jan 1, 2000

By C. Leticia Hernández, P. Martín Reyes, D. Iván Alejandrox Reyes, L. Miguel Pérez, T. Julio Cesar Juárez, G. Mizraim Uriel Flores, T. Raúl Moreno, R. Aislinn Michelle Teja

This study shows the characterization of tailings from the mining district of Coscotitlán, State of Hidalgo, Mexico. Chemical analysis by Spectroscopy of atomic absorption (AAS) allowed to quantify the concentration of Fe, Mn, Zn, and Pb as the most abundant elements in the mineral sample; in addition to the presence of Sn, Te, Bi, Ni, Co, and Cd. The presence of precious metals as the Ag (64 g ton−1) and Au (0.65 g ton−1) were identified. The greater distribution of Ag was detected in particles with diameter of 74 lm. Species as pyrite (FeS2), galena (PbS) and hematite (Fe2O3) were observed in a matrix of quartz (SiO2) by Polarized Optical Microscopy (POM), these species were also identified by X-ray Diffraction (XRD). Both the elemental and mineralogical composition of tailings was corroborated by the technique Scanning Electron Microscopy - Energy Dispersive Microanalysis (SEM-EDS).

Mar 1, 2018

By R. W. Dalzell

The performance characteristics, efficiency, and operating pressure of jute line-brattice systems were studied under varying underground conditions; various fabric grades and installation methods were used. The test results indicate that line-brattice system efficiency is dependent upon the method of ventilation the method of installation, porosity of fabric, and size of tight rib area.

Jan 1, 1966

By Márcio Zamboti Fortes

A alguns anos os setores residencial e industrial tem se deparado com mudanças de paradigmas que tangem a necessidade de melhorias em suas atividades, com o intuito de desenvolver processos com menor impacto ambiental, sustentáveis e com eficiência energética, objetivando reduzir o consumo de energia elétrica. O uso de tecnologias baseadas em fontes renováveis para a geração de energia elétrica, tais como a solar e a eólica, tem apresentado-se como uma alternativa a ser implementada por estes setores para atender às exigências do mercado, se beneficiando da difusão da tecnologia e uso destes equipamentos, para a consciente utilização da energia elétrica. A instalação e avaliação de novas fontes de geração de eletricidade estão sendo desenvolvidas pelo projeto Cidade Inteligente de Búzios através da implantação de painéis fotovoltaicos e aerogeradores de pequeno porte em unidades consumidoras residenciais, comerciais e industriais e alguns resultados estão apresentados neste texto.

Sep 25, 2017

By Izabelle Lannes Salgueiro Ferreira

O presente trabalho teve como objetivo adequar às propriedades mecânicas dos perfis ASTM A572 G60, através do estudo da influência dos parâmetros de processo de laminação e composição química do aço. Os perfis ASTM A572 G60, são utilizados nas indústrias de fabricação de torres de transmissão. A metodologia utilizada neste trabalho foi o desenvolvimento de um modelamento matemático, com base na ferramenta estatística de Análise de Regressão Múltipla. Através desta ferramenta foi possível obter previsibilidade de processo e identificar os parâmetros mais influentes nas propriedades mecânicas dos perfis ASTM A572 G60, o que possibilitou a determinação da composição química ideal do aço e os melhores parâmetros de processo de laminação.

Jul 30, 2018

By Francesco Chiappalone, Marco Invernizzi, Franco Gasperin, Fabrizio Fara

As part of the Ship Canal Water Quality Project, 2.7-mile Combined Sewer Overflow tunnel is excavated with a 21.5-foot diameter EPB Tunnel Boring Machine. Due to the difficult geological and hydrogeological conditions, the tunnel is excavated maintaining a ground support pressure between 1 and 3 bar imposing significant challenges to the projects. The first part of the paper describes the general characteristics of the project while the second part focuses on the challenges and technical details of the pressurized breakthrough that took place in a deep shaft excavated in urban environment as part of the project.

Jun 23, 2024

By James Douglas

For the past several years, inflation has placed increasing pressure on our economic system. The total effect of inflation is complex when combined with other factors which affect the economics of equipment. A mathematical model is described herein which can be programmed on a computer to determine the effect of inflation on economic life and profits after taxes. The computer output results in graphic plots which clearly show the relation of various percentages of inflation to life and profits. Inflation has become a common topic of conversation in the recent past. What is it and how can it be measured? What effect does increased inflation have on equipment policy? Research now in progress at the Construction Institute at Stanford University is beginning to unravel some of the mystery of inflation. As a start, let us answer the first question by defining the word inflation. The dictionary says that inflation is "an increase in the volume of money and credit relative to available goods resulting in a substantial and continuing rise in the general price level. It appears, in fact, that we are in an inflationary spiral which is "a continuous rise in prices that is sustained by the tendency of wage increases and cost increases to act on each other." 3 Inflation behaves just like compound interest. It takes more dollars of future years to buy an equal amount of a given commodity, be it a material or a service. Let us assume an annual inflation rate of 5 percent. Assume that 1Associate Professor of Civil Engineering, Stanford University, Stanford, California. 2Webster's Seventh New Collegiate Dictionary, Springfield, Mass., G. and C. Merriam Co., 1969. 3Ibid.

Jan 1, 1972

By R Cooksey

The Globe-Progress Mine is an open pit gold mine that is part of the larger Reefton Goldfields deposit located on the West Coast of New Zealand. The regional geology comprises a series of north to south oriented fold structures that have undergone post-deformation mineralisation. The structural geology within the mine itself is more complex, with major shears hosting numerous high-grade mineralised quartz shoots and splays that have been historically mined.The selective mining of ore within the pit is challenging due to the orientations of the hanging wall and footwall areas of the main Globe shear zone, the lithologies of these areas which range from highly brecciated and sheared material to competent mineralised host rock, and in the hazards presented by the numerous old historic underground workings. The coordination of drilling, modelling and excavation of the ore requires careful planning to maximise recovery whilst operating with the pit design boundaries.Grade control packages are custom designed to reflect the orientation of the footwall and hanging wall mineralisation. The shear material in the footwall zone dips between 60° and 70° and requires angled drilling whereas the footwall mineralisation is contained in shallow dipping quartz veins sub parallel to bedding and can be vertically drilled to best intercept the mineralisation. Ore excavation is directed so that the contact between the footwall and hanging wall is mined in the correct direction so that any non-visual ore contacts can be safely mined and that the ore-waste dilution is reduced.The ongoing grade control and selective mining of the Globe Progress deposit continues to deliver high grade ore for processing by ensuring that waste and dilution of ore is reduced and that recovery is maximised.

Aug 22, 2011

By H. D. Yu

In this paper, an evaluation about the process mineralogy of the rich iron mine in Mongolia with comprehensive methods is given; this provides foundation of the comprehensive recovery of iron and cobalt in the ore. The research shows that the iron?s grade is 61.23%, Co?s grade is 0.02%, the ore is rich iron ore and its Co content also reaches border mining grade. For the ore, if want get high grade iron concentrate powder, must identify the mineral composition and the occurrence of iron and take into ac-count the recovery of Co content as associated resources. Chemical phase analysis results show that 86.35% of iron exists in magnetite, which means that the theoretical recovery ratio of iron is close to 86%. Minerals spectrum analysis confirmed that the magnetite containing a small amount of Mg, Al, and other impurities, the actual iron minerals to 70.28%, which means that theoretically iron grade iron concentrate only close to 70.28%. Based on the result of iron chemical phase analysis, by investigating the liberation of sulfide minerals and gangue, the recovery index of iron can be forecasted, when grinding fineness is 35%, 45%, 55% and 65% bellow 0.074mm,theoretical content of Fe in iron concentrate separately is 67.71%,67.88%,68.78%,and 69.43%,accordingly the theoretical recovery of Fe is 87.38%,87.05%,86.92% and 86.63%. From the perspective of process mineralogy, the forecast mineral beneficiation indicators show that the ore is easy sorting ore, iron processing operations have higher recovery rate, but wants sorting of high-grade iron ore concentrate still need appropriate grinding fineness. Furthermore, associated element Co, existing mostly in pyrite and pyrrhotite, is valuable in the ore. Pyrite and pyrrhotite have ideal liberation under grinding, so cobalt can be easily enriched in sulfide concentrate.

Jan 1, 2014

By Larry Southwick

This Peirce-Smith Converting Centennial symposium is celebrating the contributions of two men, William Peirce and E.A.C. Smith, in advancing technology allowing the copper industry to realize its full potential. However, theirs is representative of a larger story: New, simpler technology releasing the stranglehold of older, more complicated technology, new developments in vessel configuration and design finding alternate routes around dead ends in operability, advances in technique and concepts removing roadblocks of cycle time and capacity, and overall innovation opening up vast new reserves around the world to those companies willing to embrace those improvements. Our story is also one of personalities, stubborn smeltermen versus the innovators, those inside the industry versus those from outside. It is a story of an initial borrowing from the steel industry, but also Peirce and Smith, from the refining end of the copper business, taking the ideas of Baggaley from Pittsburgh’s steel and airbrake industry, who built on what Hollway, Manhès and David, Douglas, and others had done in smelter tests, further to compete with the previous primacy and closely held expertise of the copper smeltermen in Wales. These advances have been well recorded in photographs taken over the last 150 years. A number were submitted especially for this symposium. Many others were published in the mining and metallurgy press of the times. Several mining schools also retained copies of photos either taken during field trips, or donated to the school by alumni and operating companies. This presentation will provide a selection and discussion from these sources of “converters in action”, describing the various designs, operations and developments depicted. The focus here will be on the first roughly 60 years of copper converter development, from Bessemer’s days at the dawn of this new idea, up to and slightly past the time of initial adoption of Peirce and Smith’s designs.

Jan 1, 2009