Search Documents

By C. H. Fisher

Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils4 such as gasoline, kerosene, and neutral oils from coal-tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 80 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin-free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin-free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water-soluble sulphonic acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiating between cyclic (naphthenes) and acyclic hydrocarbons (paraffins), Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons. It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings.

Jan 1, 1937

By C. G. Goetzel

Until recently porous bronzes have found many applications for self-lubricating bearings in the automotive, electrical, household appliance and general machine industries. The bulk of an annual production of several million pounds of copper powder had gone into the manufacture of these articles, of which by now more than a billion are in service. However, the war has brought severe curtailment of these bearings because of the scarcity of the two main constituents, copper and tin. The development of substitute materials of equal or superior properties has led to a large-scale replacement by products made from iron powder. In spite of the diminished interest in powdered copper-tin alloys caused by this trend, it was believed worth while to investigate some mechanical properties of these materials as a reference base for substitutes. In addition, experiments using the hot-press method were incorporated to investigate possibilities of saving vital equipment or opening new fields of applications. It must be assumed that by this time the powder metallurgy process of making porous bronzes, a development that found its first industrial applications more than 10 years ago, is well known in engineering. The patent literature and bibliography is volu- minous, most publications referring to porous, self-lubricating bronzes, containing about 10 per cent tin and I to 5 per cent graphite, with porosities in the range of 25 to 35 per cent.l-7 The excellent antifriction properties of these bearings, caused by the uniform impregnation with oil, are dependent on the interconnection of the pores and the uniform distribution of the graphite inclusions. The sintering mechanism of porous bronze, with its structural changes during the transformation of the metal powder into the sintered bearing has been shown in colored photomicrographs by Hall.* Diffusion between copper and tin was found to begin within one minute, when tin-rich transitory phases were formed. After 25 min. a homogeneous matrix of alpha was reached for an alloy containing 9.5 per cent tin and 6 per cent graphite. Price, Williams and Garrand,9 studying certain metal powder combinations in which sintering is accompanied by the cementing action of a liquid phase, including a 90-10 bronze sintered at 925°C., have found that if the treatment is carried out within the liquidus and solidus temperature range of the system, a peculiar process of alternate solution and precipitation occurs. The particles of the major solid constituent are dissolved in the minor liquid phase, but thereafter are reprecipi-tated on certain nuclei, which develop into large grains, usually rounded.

Jan 1, 1945

By J. Murray Riddell, George A. Morrison

This paper is a companion to the one by George A. Morrison on Mining a Deep Limestone Mine in Ohio.‡ Barberton is 8 miles west of Akron, Ohio, and 23 miles south of Cleveland. The underground mining of limestone at Bar-berton constitutes the world's deepest limestone mine. The stratigraphy is as follows: 0-20 ft. Loam, clay, sand and gravel. Water bearing. 2-40 ft. Fractured sandstone. Water bearing. 40-110 ft. Sandstone with interbedded shale, slightly fractured. Water bearing. 110-314 ft. Sandstone with interbedded shale, slightly fractured. Water carrying. 314-2197 ft. Shale with occasional seams of sandstone, which varies in thickness from a few inches to 4 feet. Dry. 2197-2247 ft. Limestone. Dry. 2247-2742 ft. Dolomitic limestone. Dry. 2742-2767 ft. Salt. Dry. 2767- Dolomitic limestone. Dry. All of the strata dip to the southeast, about 0.5 per cent from the horizontal. The top 110 ft. of the crust is water-bearing. The rock strata are naturally fractured to a depth of 314 ft., sufficient to allow the passage of water. In the shaft-sinking operations, a stra- turn of oil-bearing sandstone one foot thick was encountered at a depth of 520 ft., and flows of methane gas were pierced at depths of 1350 and 1952 feet. Specifications for the mine plant called for, in part, the sinking of two vertical shafts and a hoisting plant capable of producing at the rate of 300 tons per hour. No. I shaft is 550 ft. west of No. 2 shaft. Each shaft measures 8 by 17 ft. outside of steel. General features of the design (Fig. I) are: Principal set members, 6-in. H-section; connecting angles (studdles), ? by 4 by 4-in. angle irons; spacing of sets. 8 ft. centers; spacing of bearer sets, generally, 160 ft.; bearers, of 12-in. I-beams. Each bearing set featured a concrete ring about the periphery of the shaft, steel to rock, and 8 ft. in height; permanent guides, 6 by 10-in. long-leaf yellow pine, 85 per cent heart. The Shaft-sinking Operation The preliminary shaft-sinking work consisted of driving interlocked steel piling about the exterior of the shafts to depths of 35 and 32 ft., respectively, and of such horizontal dimensions as to ultimately permit the pouring of a concrete collar 2 ft. in horizontal thickness. Following the pouring of a shaft collar, a temporary wooden headframe for shaft-sinking purposes was erected. The head-frame, while ordinary, featured: (1) a storage pocket of 300 cu. ft, capacity with truck servicing facilities, and (2) pneu matically operated dump doors, which mere actuated by the hoistman, thus caring

Jan 1, 1946

By C. H. Mahoney, A. L. Tarr, P. E. Le Grand

Magnesium, it is now generally realized, differs in some important aspects from most other structural metals, not excepting even its close neighbors, the aluminum-base alloys. This is particularly true with respect to the effects of elevated temperatures on the two light metals when in the molten state. Aluminum, 0' the one hand, should not be raised above its melting point any higher than is absolutely necessary if one is to avoid danger of gas absorption and a tendency toward grain growth in the resultant casting.' Magnesium alloys, in sharp contrast, actually benefit by being heated to temperatures considerably above their melting point, It is a commonly accepted practice to establish the desired fine grain in the industrial magnesium alloys of the aluminum-hearing group by raising the temperature of the melt after the refining treatment to some 250°C (482°F.) above the melting range. To recall briefly the typical practice for magnesium alloys, the molten metal is refined by fluxing at about 730°C. (I350°F.), and after the melt has been covered with a suitable flux, the temperature is raised to between 870°C. (I600°F.) and 930°C. (1700°F.). It is then cooled as quickly as possible to the casting temperature. This superheating, as it is called, results in a fine-grained cast metal structure which has superior mechanical properties, enhanced amenability to 'solution heat-treatment, and better machinability than cast metal that has not been superheated. The minimum temperature of superheating varies to some extent with the composition of the alloys to be treated and usually increases with the percentage of magnesium in alloys containing the same constituent metals.' It should be noted that the grain-refining effect of superheating is markedly apparent only in connection with the alloys containing aluminum as an alloying Constituent—the binary alloy containing 1.5 per cent manganese, for example, is not refined in grain to any noticeable extent by a superheating effort. While the phenomenon of superheating is well known in the magnesium industry, the mechanism of the process has remained a mystery During the superheating cycle something occurs that forces a fine grain upon the solidifying metal. The process has been controlled in an empirical manner, and occasionally, especially on large-scale melts, and for no apparent cause, no grain refinement is obtained from a superheating treatment. Only a few papers of importance have been published on the subject. Of these, one of the most helpful is the paper by Achenbach, Nipper and Piwowarski,3 which gives considerable data concerning the effect of superheating on various properties such as fluidity, shrinkage and hot crack

Jan 1, 1945

By Miroslaw Hajdasinski

Estimation of the economic effectiveness of industrial development projects including mining ones is generally made on the basis of the discrete model of the value changes in time, although the character of these changes is similar to the continuous model. In this paper an attempt has been undertaken to investigate the problem of the value equivalence of both models exemplified by a construction of an underground coal mine. An effort has been made to determine the errors which for different estimation criteria appear in result of the application of the discrete model. Theoretical considerations have been supplemented with practical conclusions.

Jan 1, 1977

By Thomas Kuhn

The detailed investigation of both active and inactive submarine hydrothermal systems has gained tremendous progress during the last decades because of the increasing usage of remotely operated vehicles (ROV) as well as manned submersibles. Special aspects like the targeted sampling of chimney structures and vent fluids as well as the analysis of zonations of near-surface structures like sulfides mounds was only possible with the usage of such vehicles. However, the availability of such vehicles has been very limited because of the few number of deep-water ROVs and manned submersibles which need both a trained crew and a special research vessel. This was especially true for the German science community which did not have such devices at its disposal until recently. With the ROV QUEST 5 which is based at the University of Bremen (c/o. Prof. Dr. G. Wefer, Dr. V. Ratmeyer) this major drawback has now been eliminated.

Jan 1, 2003

By A. Shemi

Tungsten carbide scrap (WC–Co) is material generated from the tungsten carbide manufacturing process and worn out or used carbide parts from industry. Tungsten (W) ores contain about 3 wt% WO3 and their W concentrates about 10– 75 wt% WO3. Tungsten carbide scrap typically contains 40–95 wt% W. The high intrinsic value of W and the fact that the least valuable scrap contains more W than the average tungsten ore makes tungsten carbide scrap a worthy material for re-use. This study has investigated the selective dissolution of the cobalt (Co) binder phase, and recovery of tungsten monocarbide (WC) and Co using an acid leach process. The Co component was selectively leached leaving the WC solid particles intact. Further investigation using a complexing agent-aided acid leach process that takes advantage of organic chelating agents that form a soluble tungsten complex in place of the passive insoluble tungsten oxide is envisaged. The optimal dissolution of the Co binder phase using an inorganic acid in conjunction with an organic complexing agent is a novel approach with the potential of reduced leaching times and possibility of regenerating the unreacted organic acid.

By Z. Luo, W. Chen, Y. Zhao, Y. Fu, L. Dong

The gas-solid dense-phase fluidised bed includes a complex multiphase fluid-particle system; different complex exchanges significantly affect the stability of the fluidised bed. To elucidate the characteristics of fluidisation in a gas-solid dense-phase fluidised bed, this study used experimental performance tests to obtain the static density characteristics, and the attachment and flow characteristic of the dense medium. The results indicate that the bulk density of the dense medium increases first and then decreases with the increase of particle size. The airflow rate difference is used to quantify the wall attachment characteristics of dense medium and the average pressure gradient in the axial direction of the bed is approximately 20 Pa/mm under the fluidisation results. At the same settlement location, with the decrease of fluidisation number, the settlement velocity of large and small particles becomes slower, the boundaries of settlement displacement and location probability are gradually disrupted, and the falling velocity of particles with a radius of 20 mm is faster than that of materials with a radius of 15 mm. This work also established a theoretical basis for regulating the stability and separation characteristics of gas-solid dense-phase fluidised bed. Keywords: Fluidised bed, different size particles, fluidisation characteristics, flotation bubbles, settling motion

Jan 1, 2020

By Kenneth C. Stewart

The overall purpose of this study was to develop and evaluate, in the laboratory, instrumentation and procedures which might allow for the use of physical measurements of earmuff attenuation which would yield results equivalent to those obtained from psychophysical measures of attenuation. The ultimate goal was to evaluate techniques which might subsequently prove feasible for physical measurement of earmuff attenuation in the field. Current instruments were modified to have a response similar to differrences observed in earmuff attenuation as observed in Volume 1 of the current contract. Mining noise spectra were selected and presented to a single subject seated in a diffuse noise field. The subject wore one of the muffs evaluated in the earlier study and was also fitted with two physical sound measurement systems. A linear system measured the "outside" noise level and a linear system plus "correction" filter measured the "in-side" noise level. These measurements indicated that, under the procedures presented in this report, a laboratory method for measuring earmuff attenuation is feasible and yields results comparable to an extensive psycho-physical procedure.

Jan 1, 1980

By Edward Thimons, William A. Hertbrink

The effect of wind speed upon aerosol penetration into an idealized enclosure was studied The idealized enclosure was a painted plywood box that was 1 2X1 2 XI meters in volume Two fans supplied 1 7 m3 /min of filtered air to this enclosure at a static pressure of 2 8 mm of water The enclosure had a 7 5 cm diameter vent port which was isolated from the air flow around the enclosure To simulate holes in real enclosures, three 16-cm diameter holes were drilled on the front and back sides of the enclosure This simulated enclosure was placed in a tunnel-like structure The air flow from an ultra-light air craft was directed at the front of the enclosure The air speeds were varied between 14 and 36 km/hr as measured by rotating vane anemometer Static pressure in the enclosure was measured with an electronic manometer Two optical particle counters measured the particle number concentration of particles between the 0 35 to 0 5 µm inside and outside of the enclosure Aerosol penetration into the enclosure was computed as the ratio of the aerosol concentration inside the enclosure to the concentration outside of the enclosure The enclosure static pressures measured increase from 2 8 to 3 4 mm of water (P=00001) Aerosol penetration into the enclosure increased linearly with air velocity above 20 km/hr Theoretically estimated penetrations were correlated with observed penetration into the simulated enclosure When simple linear regression was used to model the observed penetration as a function of the estimated penetration, the value of the slope was 0 69±0 12 and the P value for the regression model was less than 0 0001 These results indicate that enclosure static pressure needs to be higher than the wind's velocity pressure in order to minimize aerosol penetration into these enclosures

Jan 1, 1999

By Kenneth Eilerts

[The development and operation of ?combination on wells?5/ have created new and unusual problems, many of which cast to solved only if information is available concerning the properties of the fluids produced. Data as to the characteristics of the fluids at the relatively high pressures that exist in the reservoirs are especially important, and there is growing economic concern to know what part, if any, of the liquid recovered at the surface was liquid in the reservoir, As an extension of this problem, it is important to Know whether liquid will be formed in the reservoir it as a result o a isothermal retrograde condensation when the reservoir pressure is reduced. The pressure range of such condensation, if it occurs, is significant in the design of gas-recycling plants for maintaining reservoir pressures. In connection with the operation of such plants, it is particularly important to know how gyres sure and temperature will affect the yield of the liquid phase and the composition of the gas to be returned to the reservoir. It has not been possible to predict the behavior of these fluids that have high ratios of gas to liquid by comparing them with the behavior of low gas-liquid ratio fluids at identical pressures and temperatures. Such comparison fails because the proportions in which a component will be distributed between the phases of a system at any given temperature and pressure depend increasingly on the composition of the mixture as the critical temperature and pressure of the oysters are approached. Because many combination wells are producing from reservoirs that have temperatures near the critical point, experimental date on the properties of the fluids under reservoir conditions are particularly important at this time. To rest the immediate requirements of the industry for such experimental information an equilibrium cell has been constructed at the Petroleum Experiment Station of the Bureau of Mines, Bartlesville, Okla. When adequate experimental date, have boon accumulated, it may be possible to mare dependable estimates of the phase relations ft. high gas-liquid ratio fluids at the pre runes and temperatures characteristics of ?combination-well? reservoirs.]

Jan 1, 1940

By B Murphy, A Uliana, P STrgio de Oliveira, G Ara·jo de Souza Franco, T Miettinen

Outotec has performed numerous research and development projects and various surveys in the study of reverse iron ore flotation. Over the past four years their TankCell-70 and TankCell-160 flotation cells at the Germano concentrator of Samarco in Brazil were extensively surveyed. These surveys have revealed some extreme operating conditions in reverse iron ore flotation and are the subject of this paper. Some of the findings include large variations in the content of solids in the various flotation stages. At the bottom of the cleaner cells, the content of solids by weight reached over 60 per cent, whereas at the bottom of the scavenger cell this was less than 50 per cent. Froth carry rates were also significantly different in the various flotation stages. In the case of coarse material, the scavenger cells operated at a froth carry rate of over 40 t/h.m2. With fine material, however, froth carry rates of less than 10 t/h.m2 were measured. High froth carry rates caused significant changes in the residence times at Samarco. In the rougher cells, the fifth cell had more than double the residence time of the first cell. This was even more pronounced with the scavenger cells, where the second cell had more than triple the residence time of the first cell. High froth carry rates also caused losses in iron recovery. As a consequence of such findings, it appears that different rules apply in the sizing of reverse flotation circuits compared to direct flotation circuits. Different operating parameters (mixing intensities and air flow rates) must also be used in the rougher, cleaner and scavenger cells in order to optimise the metallurgical performance. Outotec has also been working on a number of new technologies aimed at improving the metallurgical performance of iron ore reverse flotation circuits by increasing froth carry rate and decreasing fine iron entrainment.CITATION:Miettinen, T, Uliana, A, Ara·jo de Souza Franco, G, STrgio de Oliveira, P and Murphy, B, 2013. TankCell flotation at SamarcoÆs Germano concentrators, in Proceedings Iron Ore 2013 , pp 441-444 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Leoncio Méndez, Jesús Arguijo, Juan José Frausto, Daniel Castruita, Daniel Aguilar

Minera Sabinas (Grupo Peñoles), localizada en Sombrerete, Zacatecas, México, produce concentrados de cobre y zinc. Su proceso es un circuito de conminución de quebradoras y dos molinos de bolas en circuito cerrado con hidrociclones seguido de un circuito de flotación, a partir de mineral polimetálico extraído de una mina subterránea. Su problemática consiste en que la recuperación por flotación disminuye significativamente cuando minerales con contenido de pirrotita son procesados. La flotabilidad natural de la pirrotita supera la cinética de flotación de las especies de cobre y zinc y limita la capacidad de la concentradora para generar concentrados vendibles. Este artículo presenta un diagnosticó de los problemas que se tienen cuando se procesan minerales con alto contenido de pirrotita, así como resultados de un programa experimental a escala laboratorio realizado en el CIDT de Peñoles y en sitio. La investigación se enfocó en definir un esquema de reactivos para poder procesar minerales con pirrotita en su composición. Compósitos de alta y baja ley de cobre fueron usados en la investigación. Se identificó el agua de proceso como una fuente de iones calcio y sulfato. Se desarrolló un esquema de reactivos orientado a promover la selectividad de las especies de valor respecto a la pirrotita, incluyendo tratamiento del agua de proceso.

Sep 20, 2019

By R. Costantini

A. Brebner (Chairman, Dept. of Civil Engineering, Queen's University, Kingston, Ont., Canada) — Under the heading of friction losses, the author, in Eq. 10, gives the relationship

Jan 1, 1962

By Adam Moore, Peter Radziszewski, Matt Gallimore

"Stirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented. In the context of the mining industry, interest in stirred milling technologies has grown over the last 20 years where the typical observation reported inDespite these developments, the tumbling mills are continuing to be used in fine and ultrafine grinding applications. The main reason for this, as communicated at the Canadian Mineral Processors roundtable discussion in 2013, is that the comfort level in understanding stirred milling technologies is not at the level of that of tumbling mills.At CMP 2014, one contribution was made to explore how mill design affects power and energy in a stirred mill. While the 2015 CMP paper explored the application of one scale-up methodology to the Gibraltar case. For the CMP 2016, the aim of this paper is to contribute to increasing the general comfort level with stirred milling technologies by developing a better understanding of the different scale-up methodologies used. This will be accomplished by first completing an overview of the scale-up models found in the literature followed by a review of the different testing and scale-up procedures. This review will be supported by a number of case studies found in the literature. The paper will close with a discussion on some of the challenges that these models and methodologies have and how future research might contribute to overcoming them.IntroductionStirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented (Stehr, 1988). The year 1948 saw the successful application of Du Pont’s “sand mill” for pigment grinding. Subsequent years have led to the development of different types of stirred mills spanning a number of industries that require fine and ultrafine grinding."

Jan 1, 2016

By Alfred L. Ransome

The plan to develop a standard system of names and definitions of regions and districts in Alaska was borne of the need for a tool to use in statistical and economic studies of the mineral industry of the Territory. The purpose of this report is to present to the mineral industry, and to those individuals interested in the mineral or allied industries in Alaska, the system used by the Bureau of Mines in connection with its legal function of collecting and disseminating mineral statistics. It is hoped that the specific descriptions given will result in a more complete understanding of what is meant by the regional and district names that appear in publications of the Bureau of Mines relative to the mineral industry of the Territory. Problem of Standardization of Names and Definitions The question might be asked, does the naming and defining of regions and districts in Alaska present a problem relative to the establishment of a standard? Is it necessary to establish a standard?

Jan 1, 1954

By Shigeru Tsutsumi

The rapid development of transportation facilities in Japan focused the attention of this country on the possibility of converting the existing coal resources (of which there was an abundance) into liquid fuels, for which there was a constantly increasing demand. Previous work had indicated that this could be accomplished by utilizing one of two processes - the Bergius process, in which high temperatures and high pressures were employed to effect direct liquefaction of the coal, and the Fischer-Tropsch process, in which an indirect liquefaction of coal was accomplished by the production of liquid hydro-carbons from hydrogen-carbon monoxide mixtures. This report describes some investigations into the latter process, which was first developed by Fischer and his colleagues in the Coal Laboratory in Muhlheim, Germany, in 1923. By 1932, these investigators had achieved a 60-percent theoretical yield (152 ml. of liquid hydrocarbons per cubic meter of 2H2:ICO synthesis gas) by using a precipitated Co-Th02 catalyst.3/ At the same time (1932), Dr. Kita of Kyoto Imperial University and Messrs. Fujimura and Tsuneoka obtained 145 ml. of gasoline (C5+) per cubic meter of synthetic gas by using a Co-Cu-Th-U catalyst. 4/ This report is a description of the experimental results subsequently obtained at the Fuel Research Institute, Kawaguchi City, Saitama, up to 1935.

Jan 1, 1951

By Vinay Kumar

The present investigation describes R & D studies carried out for recovery of copper from the sulfate solution expected from the leaching of e-wastes in presence of minor constituents such as cadmium, zinc and nickel using solvent extraction process. In order to extract copper in continuous mode in mixer settler unit (MSU), basic studies have been made to optimize the experimental condition using 5%LIX84 in kerosene. Subsequently, the solvent extraction of copper was made in MSU maintaining leach solution flow rate 4.0 L/h and A/O ratio 1. The results showed complete extraction (~97%) of copper in three stages at A/O ratio 1 from the aqueous solution containing 1.98g/L Cu at pH 1.91 in presence of impurities. Loaded metal was completely stripped after scrubbing with 10% sulfuric acid in two stages. The stripped solution could be used for metal/ salt recovery by electrolysis/ crystallization.

Jan 1, 2010

By Ryan C. Stephan, Christopher Mark

"Some of the weakest roof in United States coal mines is found in the Illinois Basin. Historically, the Illinois Basin has also suffered from high rates of unplanned roof falls and rock fall injuries. During the past decade, however, roof fall and rock fall injury rates have fallen dramatically, and are now lower than the national average. Several technologies are responsible for the improvement. Roof screen was rarely used ten years ago, but a number of mines now use it on a regular basis to prevent rock falls and rock fall injuries. Other roof skin control fixtures and work practices have contributed as well.The reduction in roof falls is also directly attributed to enhanced intrinsic roof support. Stiffer primary bolting patterns have reduced the magnitude of roof spalling and roof sag. They have also helped create a more intact beam that is able to be suspended from longer cable bolts. Cable bolt design methodology has also contributed to this reduction in roof falls. Some early cable bolt applications were unsuccessful because they employed as few as two cable bolts per intersection. This paper describes a methodology for estimating rock loads for support design.ROOF FALL TRENDS IN THE ILLINOIS BASINAlthough the Illinois Basin has a long history of poor roof conditions and high rates of unplanned roof falls and rock fall injuries, recent data indicates a change in the trend. Roof fall rates are determined by dividing the total number of non-injury roof falls by the total number of hours worked underground. The data is considered for 200,000-man hours. While the Illinois Basin was once a coalfield experiencing roof falls at nearly twice the national average, it is now at or below the national rate. Figure 1 indicates the trend over the past 20 years. In 2008, the Illinois Basin mines experienced 5.06 roof falls every 200,000-man-hours, compared to only 0.75 in 2018.There has also been a significant reduction in the rate of rock fall injuries in the Illinois Basin coal mines, as shown in Figure 2. In 2008 there were 1.48 rock fall injuries every 200,000-man-hours, compared to only 0.43 in 2018.ILLINOIS BASIN COAL ROOF GEOLOGYThe roof rock in the Illinois Basin has been studied in the past to understand the primary causes of roof failures (Molinda et al., 2008; Thompson, 2010; Molinda and Mark, 2010). Rusnak and Mark (2000) evaluated 10,000 laboratory strength tests from 800 rock units and concluded that for shale, siltstone, and sandstone, the strength of the Illinois Basin variety was less than half that of the same rock types in Central Appalachia (Figure 3). A study of Coal Mine Roof Rating (CMRR) measurements in more than 200 US coal mines also found that weak roof was predominant in the Illinois Basin (Mark and Molinda, 2005)."

Jan 1, 2019

Mining One (M1) is often challenged with the task of evaluating deposits considering open cut and/or underground (UG) mining methods. In many near surface deposits a combination of both methods results in the optimum economic means of exploitation. As common as it is to have open pit mines eventually develop into underground mines, theory associated with determining the optimum underground/open pit interface location continues to be subject to refinement. With recent developments in underground software packages, the generation of rudimentary underground mining stopes from basic economic inputs is not only fast, it provides a practical underground mining solution. The determination of the open pit/underground interface is not new to Gemcom's Whittle 4X (Whittle). However, its solution has only ever claimed to be indicative, mainly due the rudimentary nature of how Whittle represents any potential underground mining. The efficient generation of the aforementioned underground mining solution has provided mining engineers with a unique opportunity. Underground mining can now be represented within the Whittle environment to allow the open pit/underground mining scenario to be modelled with increased accuracy. Providing Whittle with the ability to now consider mineable underground stopes combined with the consideration of time value of money (discounting), has delivered a solution with higher credibility than ever before.This paper will elaborate on the potential value gains associated with improved accuracies in the modelling of any potential underground mining in the Whittle environment. Furthermore, it will explain the importance of incorporating time value of money in the optimisation process to provide a consistent solution through to pit selection and final analysis.

Dec 6, 2010