Search Documents

GENTLEMAN: The year 1928 was another in the history of the Institute which was marked by quiet growth and steady progress. The total membership as of December 31, 1928, was 8703 as compared with 8438 on December 31, in 1927. Again the main increase has been in Members and the number of Junior Associates is less. As will be seen also by the Treasurer's report, the increase is reflected in larger receipts for dues indicating that fewer have had to be dropped for non-payment. There has been a gratifying increase in the number applying for reinstatement and it seems clear that interest in and attachment to the Institute has notably increased. The year was signalized by the merging of the Rocky Mountain Club with the Institute which brought to our roll one hundred and forty who were not previously members from among the men who have made the West. It also brought to the Institute a strong tradition of good fellowship and a fund of over $100,000, the interest from which is to be expended so far as may be, for purposes beneficial to the Western states. The Endowment Committee expects to see other and similar funds entrusted to the Institute and the Board has already appointed a special committee to consider all projects for expenditure of the revenue from them. It is felt that with the organization and personnel available in the Institute even modest revenues can be made to yield large returns in the way of scientific and technical knowledge. Within the year also, a third great Division has been organized within the Institute, building on the foundation of the old Iron and Steel Committee. The new Division signalized its independence by joining the Lake Superior Mining Institute in a visit to the Menominee Range in September and by furnishing material for a special volume of 353 pages, "Iron and Steel" Technology in 1928," printed and distributed in December. The Institute of Metals Division held its fall meeting with good attendance as one feature of National Metal Week at Philadelphia in October, and published its volume of Proceedings, running to 836 pages, in August. "Petroleum Development and Technology in 1927," 844 pages, came out in June and recorded the work of the Petroleum Division. A most interesting Fall meeting was also held by the Division at Tulsa,

Jan 1, 1929

By Ernest H. Gilmour

Introduction An earth science teacher at the junior high school level has the potential of working with 450 students per year. And these young people are at an age where they can be properly informed about the importance and necessity of a viable, domestic minerals industry. It was with this philosophy that a course was developed at Eastern Washington University for science teachers entitled, "The Minerals Industry of the Pacific Northwest." The two-week course is sponsored by the Northwest Mining Association and the Idaho Mining Association. It was first taught during the summer of 1971 and will be taught during the summer of 1986 for the sixteenth straight year. It is a two-week mini-version of the very successful six-week course taught at the Colorado School of Mines. In 1971, Russ Chadwick was President of the Northwest Mining Association. He suggested that such a course should be developed and offered at Eastern. It was determined that tuition scholarships would be necessary. This would ensure that a reasonable number of teachers would register for the course. Say a teacher has five classes a day, with 30 students in each class. Some 150 students come into contact with that teacher each term. With three terms a year, an instructor works with about 450 students per year. So, with 20 teachers in the course, it was possible that 9000 students a year could learn from our informed teachers. And now, after 15 years, more than one million students have learned about the minerals industry from teachers who have completed the course. The course is designed to take the teachers through all aspects of the minerals industry. Most of the lectures are given by the working geologists and engineers who talk about their jobs in the industry. This is extremely important for the credibility of the course. The teachers realize that the lecturing professionals really believe in what they profess. Industry fundamentals The course begins with a lecture on the need for minerals in a modern society. Most of the teachers do not realize how critical minerals are to every aspect of our daily lives. The lecture is followed by the US Bureau of Mines movie, "Minerals Challenge." An exploration geologist then discusses what is involved in the exploration for a mineral deposit. This includes a case history that the geologist has actually been involved in

Jan 9, 1985

By Dennis K. Mortensen

The Role of the Operator The ultimate objective of any installation is to be able to accomplish the useful work that it was originally designed for. The operator needs a tool that he can both operate effectively and maintain efficiently. The overall design and subsequent installation of a comminution circuit should be a marriage of good engineering practice and practicality. Since the operator must operate and maintain his equipment, his input into the design and installation is vital to its ultimate success. The design of a crushing or grinding circuit is dependent upon many factors including flowsheet design, equipment selection, physical layout, space restrictions, climatic restrictions and considerations for future expansion. The operator must live on a day-to-day basis with the results of the final design and installation. The most satisfactory operation will result when the operator has a major input into each of the criteria that are used to define the final design and installation. The operator referred to is not only the mining company or organization that is having the installation built for its specific use but, more specifically, the person or persons that will actually be responsible for its daily operation and maintenance. Future references to the "operator" will include those individuals with that daily reponsibility. The operator's input into the installation of the circuit is of equal importance to his input into the design. The engineering organization which puts together all of the various design drawings for circuit installation is generally restricted to trying to get all of the details onto a multitude of 24" x 36" two dimensional drawings with a few isometric drawings thrown in. It's almost impossible to get all of the details of a final installation onto all of the drawings, and field modifications are necessary to make everything fit properly. In a multilevel installation, such as a grinding or crushing circuit, it is difficult to envision space requirements to adequately operate and maintain the various pieces of equipment simply by looking at a set o£ drawings. For some designs it is helpful to build a scale model so that a more realistic view of what the installation will look like can be seen. The scale model allows the operator to make whatever changes in design are needed to operate and maintain his equipment most effi-

Jan 1, 1982

By Jamil M. Khalifeh, Shadia J. Ikhmayies, Bothina A. Hamad

"We computed the optical properties of the cubic niobium nitride (o-NbN) compound using the full potential linearized augmented plane wave (FL-LAPW) method within density functional theory (DFT). The complex dielectric function and optical constants, such as optical absorption coefficient, refractive index, extinction coefficient, energy-loss spectrum, and reflectivity, are all calculated and compared with experimental results. The behavior of the computed quantities is similar to that obtained experimentally, but the optical positions are shifted to lower energies. This shift was related to the strong interband transitions, which are located at energies higher than 5 eV for NbN- as they are for IV B transition-metal mononitrides- and they appear in the computed spectra and not in the experimental spectra. These interband transitions simply shift the position of the reflectivity edge or the screened plasma frequency to the longer wavelength side.IntroductionIn recent years, NbN, as a transition metal nitride, has become a very popular material due to its high hardness, melting point, wear resistance, chemical inertness and temperature stability, which makes it suitable for use as emission cathodes in microelectronics and sensors, optical films and micro-mechanics etc [l]. Niobium nitride has long been known as highly polymorphic material, for which several crystalline structures have been reported in the literature [2]. These structures include the well known super-conducting rock-salt (Fm-3m, or Bl) structure (o-NbN), the hexagonal structure with space group p63/mmc and prototype Fe2N (18fuN), the hexagonalstructure with space group p63/mmc and prototype NiAs ~-NbN) and others.There has been a lot of computational studies for the structural and electronic properties ofNbN [3, 4-7], but according to our knowledge there is not any computational work that has been devoted to study the optical properties of this transition metal compound. At the same time a number of authors had performed experimental work in this direction. For example, Xin-kang et. al [l] studied the microstructure and optical properties of magnetron sputtered NbN thin films. Torche et. al [8] studied the composition, structure, electrical and optical properties of nonstoichiometric niobium nitrides. Newport et. al [9] investigated the reflection and transmission spectra of cubic niobium nitride films, and Tanabe et. al [10] had investigated the optical parameters and reflectivity of reactively sputtered NbN thin films by using in situ ellipsometry."

Jan 1, 2013

By A. B. Kinzel

Advance in the art of slag control has been very rapid in the past few years. The viscosimeter method for slag-reaction rate and composition, together with the phosphorus and other methods mentioned by Dr. Herty, allow the steelmaker to rectify and control the slag in the finish period of the heat with much greater precision that ever before. However, the steelmaker's problem is more complex, and in order to make steel of proper analysis in the most economical manner the constitution of the initial slag that has formed immediately after the lime is up in the furnace is of prime importance, as it is one of the factors that determine the carbon content of the charge as melted. Many heats melt with high carbon and some with carbon much lower than is expected so that, on the average, increased furnace time is necessary before reaching the finishing period. The problem, therefore, is to so regulate the slag-making additions that a suitable initial slag will be formed at once. Where all cold metal charges are involved, particularly where the iron and scrap are selected, this may be done with a fair degree of regularity. This regularity results not only in better conditions at the beginning of the heat and during the carbon drop, but also the need for smaller slag-modifying additions toward the end of the heat. The above has been well demonstrated by the work reported by Reagan in the past few years. Where large amounts of cold pig or hot metal are used, the problem becomes more involved. It is much more difficult for the steelmaker to be sure that for any given furnace the heat will form the desired initial slag. Observations of many heats indicate that the pig iron is a dominating factor in the constitution of the slag formed. The scrap is also a factor but in general could be roughly classified and a correction made therefor. The necessity, therefore, arises for a method of correlating the pig-iron charge and type of slag formed for any particular furnace, which resolves itself into a measure of those qualities of the pig iron which affect the slag. The amount of silicon, manganese, phosphorus and sulfur in the pig iron will probably have some effect on the type of slag formed, but

Jan 1, 1935

By David K. Mitchell

The mineral pyrite (or marcasite) occurs in coal beds as balls, lenses, veinlets and bands. Several million tons are w-asted annually on the refuse dumps from coal mining and coal-preparation activities. Sporadic attempts have been made in the United States to recover this pyrite for manufacture of sulphuric acid but only a few plants have succeeded in recovering it on a commercial scale. Shipments of pyrite from coal mines during 1941 were reported as follows: Illinois -The Midland Electric Coal Corp., Henry County, shipped 12,026 long tons containing 46 pct sulphur, at its Atkinson preparation plant. Indiana—The Snow Hill Coal Corp. produced pyrite from its Talleydalc preparation plant in Vigo County. Kansas—The Mineral Products Co. produced 3902 long tons of pyrite containing 44 pct of sulphur from picking table and washery refuse. Specifications for coal pyrite for acid manufacture rangc from 5 to 8 pct maximum carhon limit, and 42 to 45 pct minimum sulphur limit. Where flash roasting is practiced, the pyrite must be minus 100-mesh. Most companies give no size specifications. One company specifies 20- mesh or finer. Impurities in pyrite other than carbon may limit its use—for instance, arsenic, probably as arseno pyrite-—even though a concentrate can be made complying with specifications otherwise. Pyrite-recovery Plants Bradford breakers and picking tables may be used to make a marketable product where the pyrite occurs largely in sizes coarser than about I in. To make a grade of concentrate acceptable to sulphuric-acid plants the pyrite must break freely from the accompanying coal and slate, which is a rare condition to find. Most pyrite occurring in coal beds requires crushing and an abrasive type of grinding to free it of entwined coal and slate, followed by mechanical concentration by jigs, tables or other concentrating devices suitable for heavy ores, to make a satisfactory concentrate. At the Snow Hill Coal Corporation's plant in Indiana and at the Midland Electric Corporation's plant at Xtkinson, Ill., the final concentrate is made by a mechanical jig. The most recent and complete mill for concentrating pyritc from coal-mine refuse is that of the Mineral Products Co. at West Mineral, Kans., in which jigs and tables are used. Many regrinds and recirculations of products are necessary to get a concentrate of uniform grade. Trends On the whole, the economics of recovering pyritc from coal is not favorable. Cer-

Jan 1, 1948

By J. P. Mogan

As diesel exhaust contains a mixture of several materials of varying degrees of toxicity which interact to a currently undefined extent in their effects on health, the prescription of a quantity of ventilating air to dilute the exhaust to a safe level is necessarily, to some extent, arbitrary. Some jurisdictions rely on the application of a safety factor to a single "governing" component (usually nitric oxide for most modern diesel engines). Others specify that the total of the "adjusted" concentrations (actual concentration divided by maximum permissible concentration) not exceed "one" for related constituents (irritant gases for example). Neither of these approaches, however, takes account of the interaction of the gaseous constituents with diesel soot (although many studies verify such interactions), nor do they provide any economic incentive for reducing pollutants which are not included in the criteria for ventilation. Because of these factors, the Canadian Department of Energy, Mines and Resources awarded a contract for a study of the current literature bearing on the "Health Implications of Exposure of Underground Mine Workers to Diesel Exhaust Emissions" (1). One goal of this study was the formulation of a new ventilation criterion. The contractors, Ian W. French and Associates, studied more than 1500 literature citations which they interpreted in a 350 page report and summarized in a companion 1600 page annotated bibliography. In the recommendations section of the report, they defined a new 'health effects index' or ventilation criterion "V" as follows: [ ] The contractors consider that a "V" between 3.0 and 4.0 poses a moderate threat to health which could be alleviated by the use of protective equipment such-as filter helmets. If V exceeds 4.0, an increase in ventilation quantity to reduce the pollutant levels is indicated. In the case of mines with a quartz content in excess of 20% in the ore, the contractor recommends that a term. [Quartz]/ [Threshold Limit Value Quartz] be added to the equation, and [2.0 = ?v? = 30] be the range justifying protective equipment, with added ventilation if "v" exceeds 3. A degree of pragmatism was inherent in the development of the equation, as the contractors recognized that the components of the index, if it is to be useful in the near term, should be within current routine underground environmental assay capability.

Jan 1, 1980

TENTATIVE -reservations for the cruise to Vene-zuela and the West Indies have been coming in nicely, but there is plenty of room yet for mem-bers and their friends. The exact schedule is even yet not entirely fixed. Owing to difficulty in securing the release. as, early as had been hoped, of the Lapland, which is so particularly well adapted to this cruise, the time has been shortened. The steamer is now scheduled to sail at midnight on Jan. 30 or 31, the exact date still to be determined, and to return on Feb. 20. This change will so shorten the time as to permit many more to attend as they need not be so long. away from their business. It .will necessitate cutting out the pro-posed day at Kingston in Jamaica, and, if the steamer is -not available until Jan. 31, may also necessitate passing Bermuda without a stop. The time remaining will, however, allow a stop of one and a half days at Havana, a full day, on the Canal, Zone with opportunity to go through the locks, the Culebra Cut, and to see Panama, and the five days, planned in Venezuela: Just how many can be taken into Lake Maracaibo and the oil fields will depend on the local transportation that can be made available. It may be necessary to restrict this shore party as to numbers, but if so, something interesting will be provided to fill the time of the others. At other points accommodations will be ample for all Members of the excursion will get back in time to register and attend the smoker on the opening day of the meeting as also possibly the Monday after-noon sessions if any be held. The usual Institute rules for excursions will be fol-lowed assigning space in the order of application with members first. Guests vouched for by members will be heartily welcomed. The steamer rate varies accord-ing to the accommodations chosen. There are a limited number of one and two berth rooms at the minimum of $250 per passenger with plenty of room at $300 to $500, according to space and location. At prices from $750 up per passenger rooms with private bath are to be had. Plans are on the-basis of two people in a three-berth room. The steamer, which is especially fitted for crusing, has ample deck-space and numerous large

Jan 11, 1927

By H. F. Seifert

THE classification and preparation of non-ferrous scrap metals is a subject of interest to every individual and corporation that employs in its processes of manufacture non-ferrous metals and alloys and accumulates in such manufacture scrap from these materials for disposition in the form of turnings, borings, short ends, punchings, clippings, grindings, washings, etc. All too frequently the disposition of such scrap is left to individuals who have no knowledge of the subject either from a metallurgical or a commercial standpoint, or both. Much money is thus lost which with a little more intelligent effort might be saved, and in this day of fierce competition and small profits such an opportunity cannot be ignored. The Mineral Resources of the United States for the year 1925, the latest issue available (Part 1, page 221), gives the secondary non-ferrous metals of certain classes recovered in the United States for the year 1924 to 1925 as shown in Table 1. The figures are tabulated simply to give the reader some idea of the scope of the secondary non-ferrous metal industry. Approximately 900,000 tons of an annual value of $244,000,000 were recovered in the year cited. In 1916 (again using the Mineral Resources of the United States as authority) the tonnage reclaimed was approximately 632,000 tons and the value, because of the high prices for metals prevailing at that time, amounted to $265,000,000. It is not the purpose of this paper to discuss smelting and refining operations or the feasibility of an organization, primarily engaged in some other activity, conducting smelting and refining operations to convert its own non-ferrous scrap metals and alloys. The classification and preparation of these non-ferrous materials is a preliminary step, regardless of what subsequent operations the material may pass through or where these operations may be conducted. For that reason the subject can be readily discussed without any reference to subsequent activities. Space must be provided, with suitable handling facilities, scales and the necessary storage bins where the material may be accumulated. The scope of the activity, the nature of the industry and the tonnage handled will determine, in a large measure, what preparation, if any, it may be desirable to give these scrap materials to put them in the best marketable condition. By preparation is meant largely what, for the want of a

Jan 1, 1928

By Güven Önal, Zeki Dogan, Neset Acarkan

"In general, the processing of glass sand may involve comminution, washing, wet classification and attrition scrubbing. Additional processes may include magnetic separation, flotation and leaching in various combinations.Yaliköy sand dune deposit is located near to Istanbul on the European side by the Black Sea coast. The reserve of deposit is around 70 million tons. Iron content of Yaliköy sand dunes is 0.48 % Fe2O3 and not suitable for glass manufacture. The iron content of glass sand should be less than 0.15 % Fe2O3 for window glass manufacture and 0.05 % Fe2O3 for glassware. In this study, it was aimed to produce glass sand with less than 0.15 % Fe2O3 for window glass and with less than 0.05% Fe2O3 for glassware manufacture from Yaliköy sand dunes. A representative sample with a weight of 200 kg was taken from Yaliköy sand dunes deposit through opening small pits.• Mineralogical studies have shown that iron is present in three forms:• Hematite, limonite, clay and iron silicate minerals such as epidote and garnet occur in free form.• Quartz grains are coated by hematite and limonite.• Iron is also present in the cracks of quartz grains.Free iron minerals such as hematite and limonite and silicate minerals were subjected to magnetic separation and flotation for removal. Iron coatings were tried to be removed by scrubbing and leaching. Iron removal in the cracks of quartz grains was attempted by grinding and leaching.Under optimal conditions, sand concentrate with 0.38 % Fe2O3 was obtained by means of high intensity disc type magnetic separation. Grinding and scrubbing were applied to see the effect of size reduction and attrition at room temperature and 90 ºC, by using non-magnetic fraction. Sand concentrate with 0.13% Fe2O3 was obtained at 90 ºC in this test.Sand sample which was previously ground to minus 0.5 mm and scrubbed, was floated by using sulphonates as collector. After flotation tests, sand Concentrate was obtained with 0.11 % Fe2O3.The optimum iron removal was achieved by H2SO4 leaching at 90 ºC depending on acid concentration and leach duration in static, percolation and agitation leaching. Agitation leaching was done by the use of mixer at 600 rpm, 50% solids and leach duration was 15 minutes."

Jan 1, 2003

By D. H. Wertz, R. R. Furlong

Dry room equipment at Donora Zinc Works is of the design which prevailed at the time the plant was built in 1915. It consists of 11 adjoining rooms, each being 99 ft long, 11 ft wide, and 7 ft high and having a capacity for 1040 retorts. Heat is supplied by steam coils beneath the slatted wood floor and by warm air ducts at the ceiling. Drying practice is about the same as that generally followed in the industry except that, under normal zinc furnace operations, the maximum drying time is 45 days. During certain seasons of the year the drying process was seriously affected by varying weather conditions which frequently resulted in a scrap loss of 5 to 7 pct. Because of these unfavorable conditions, which caused uneven drying and strains in the retorts, increased retort failures in the zinc furnaces were recorded. Regulation of temperature and humidity under all conditions appeared to be the logical solution of this problem. Controlled drying had been developed for a number of ceramic products and investigation of several such drying processes in this area revealed favorable results. Along with control of drying conditions and the attendant decrease in scrap losses, plant operators also reported a material reduction in drying time. Another factor affecting the decision to proceed with this development was the drastic change in market conditions for retort clay. Curtailment of shipments from the chief source of supply made it necessary to proceed with blending of other available clays, but quality of these clays was questionable for adequate retort life in the 24 hr furnace cycle. Rapid furnace testing of new mixtures was desirable but impossible with the prolonged drying schedule. Therefore development of a controlled drying process for zinc re- torts offered the solution to the problem of rapid testing of retort mixtures. Description of Process and Equipment The freshly extruded retort is cylindrical in shape, 58 in. long, 9 in. id and has 1 1/8 in. side walls. One end is closed and approximately 2 in. thick. The moisture content of this "green" retort is about 17 pct which means a necessary removal of 30 lb of water per retort. Retorts are set on the slatted floor of the dry room with the closed end down. The controlled drying process depends upon the circulation of a large volume of conditioned air at low velocity. To provide for uniform distribu-

Jan 1, 1950

By A. B. Kinzel

Advance in the art of slag control has been very rapid in the past few years. The viscosimeter method for slag-reaction rate and composition, together with the phosphorus and other methods mentioned by Dr. Herty, allow the steelmaker to rectify and control the slag in the finish period of the heat with much greater precision that ever before. However, the steelmaker's problem is more complex, and in order to make steel of proper analysis in the most economical manner the constitution of the initial slag that has formed immediately after the lime is up in the furnace is of prime importance, as it is one of the factors that determine the carbon content of the charge as melted. Many heats melt with high carbon and some with carbon much lower than is expected so that, on the average, increased furnace time is necessary before reaching the finishing period. The problem, therefore, is to so regulate the slag-making additions that a suitable initial slag will be formed at once. Where all cold metal charges are involved, particularly where the iron and scrap are selected, this may be done with a fair degree of regularity. This regularity results not only in better conditions at the beginning of the heat and during the carbon drop, but also the need for smaller slag-modifying additions toward the end of the heat. The above has been well demonstrated by the work reported by Reagan in the past few years. Where large amounts of cold pig or hot metal are used, the problem becomes more involved. It is much more difficult for the steelmaker to be sure that for any given furnace the heat will form the desired initial slag. Observations of many heats indicate that the pig iron is a dominating factor in the constitution of the slag formed. The scrap is also a factor but in general could be roughly classified and a correction made therefor. The necessity, therefore, arises for a method of correlating the pig-iron charge and type of slag formed for any particular furnace, which resolves itself into a measure of those qualities of the pig iron which affect the slag. The amount of silicon, manganese, phosphorus and sulfur in the pig iron will probably have some effect on the type of slag formed, but

Jan 1, 1935

By J. T. Brown

AS far as could be ascertained, no one had previously investigated the creep strength of silicon poly-crystals. Literature has appeared showing evidence for plastic deformation in silicon single crystals and whiskers.*1"6 Also the fact that germanium, a material of similar crystal structure to silicon undergoes plastic deformation under stress at temperatures above about 60 pct of its melting temperature, has been known for some time.2"4'7 This investigation was performed for the purpose of determining the strength and ductility of silicon polycrystals under creep conditions that would give fairly long times to rupture. PROCEDURE The silicon specimen blanks were obtained by first placing granulated transitor grade silicon (99.999 + pct pure) in a silica crucible. The crucible was surrounded by a graphite susceptor, and induction heating was used for melting the silicon in a vacuum furnace. Blank specimens were formed by freezing molten silicon onto a polycrystalline seed of silicon in a vacuum furnace. The seed was attached to a motor driven revolving rod. As silicon solidified, this rod was gradually withdrawn from the melt. A shape with a contracted center section was obtained by varying the rate of withdrawal from the melt. Specimens for the creep-rupture tests were ground from these "pulled" blanks. Creep-rupture tests were performed in spring loaded machines under constant load at 1800" and 2000° F. RESULTS AND DISCUSSION A test specimen which was sectioned longitudinally is shown in the photomacrograph in Fig. 1. Very little deformation has taken place in the portion of the specimen shown, however, slip lines from several slip systems within the same grain, and deformation band formation was seen. The elongated appearance of the grains is due to the method of growing the specimens. One of the most interesting aspects of the results obtained from the creep-rupture tests was the high strength and the accompanying large amount of ductility. The data obtained is listed in Table I which shows the stress to rupture in 100 hr at 2000°F is between 8000 and 9000 psi. This indicates that silicon's strength at 2000°F is about equal to that of the best commercial super-alloys. It is important to mention that silicon has less than 1/3 the density of iron-, nickel-, and cobalt-base alloys. The usual type alloys for high-temperature applications

Jan 1, 1960

By R. B. Newcombe

Despite abnormal economic conditions and the unhealthy state of the petroleum industry, 1930 closed without any marked decline in total production of oil in the Middle Western States. The most accurate figures available would indicate for this district an output of close to 25,000,000 bbl. for 1930 as compared to 26,000,000 bbl. for 1929. This can be accounted for by the settled nature of a great many of the wells producing in this area and the favorable geographical position, which affords adequate refining and marketing facilities. The only new flush production field discovered in the area was the Legrande oil pool in southeastern Hart County in western Kentucky, where wells up to 1000 bbl. initial have been reported from a shallow depth. Important extensions have been found in a number of central Ohio fields, and activity in the central Michigan area resulted in new pools along the northwest trend of the Mt. Pleasant structure. These new districts, known as the Leaton and Vernon pools, have not yet reached the scope of the Mt. Pleasant field proper, and although the structure is similar, sand conditions are not strictly analogous. Wildcatting was retarded somewhat by the scarcity of market for oil and many important wells were shut down for several months. This has not shown such a profound effect on production as the reticence of operators to drill inside proven locations. The major companies have not been able to dispose of their oil and the smaller operating units are having trouble financing their projects. The result is that oil in sight is not being produced and output is suffering accordingly. Another important effect on production was the introduction of proration by the major crude purchasers and a voluntary shut-down by Kentucky operators. This step became necessary because of the glutting of lake port refineries with Mid-Continent oil, and was not fostered by regulating state bodies, as in the case of the southwestern states. Small refining units have sprung up to meet this situation in a number of instances but they have experienced some difficulty in disposing of their product because of "dumping" tactics from other quarters. New refinery outlets on the Great Lakes and new pipe line connections should tend to alleviate this difficulty during the coming year. The

Jan 1, 1931

By David K. Mitchell

The mineral pyrite (or marcasite) occurs in coal beds as balls, lenses, veinlets and bands. Several million tons are w-asted annually on the refuse dumps from coal mining and coal-preparation activities. Sporadic attempts have been made in the United States to recover this pyrite for manufacture of sulphuric acid but only a few plants have succeeded in recovering it on a commercial scale. Shipments of pyrite from coal mines during 1941 were reported as follows: Illinois -The Midland Electric Coal Corp., Henry County, shipped 12,026 long tons containing 46 pct sulphur, at its Atkinson preparation plant. Indiana—The Snow Hill Coal Corp. produced pyrite from its Talleydalc preparation plant in Vigo County. Kansas—The Mineral Products Co. produced 3902 long tons of pyrite containing 44 pct of sulphur from picking table and washery refuse. Specifications for coal pyrite for acid manufacture rangc from 5 to 8 pct maximum carhon limit, and 42 to 45 pct minimum sulphur limit. Where flash roasting is practiced, the pyrite must be minus 100-mesh. Most companies give no size specifications. One company specifies 20- mesh or finer. Impurities in pyrite other than carbon may limit its use—for instance, arsenic, probably as arseno pyrite-—even though a concentrate can be made complying with specifications otherwise. Pyrite-recovery Plants Bradford breakers and picking tables may be used to make a marketable product where the pyrite occurs largely in sizes coarser than about I in. To make a grade of concentrate acceptable to sulphuric-acid plants the pyrite must break freely from the accompanying coal and slate, which is a rare condition to find. Most pyrite occurring in coal beds requires crushing and an abrasive type of grinding to free it of entwined coal and slate, followed by mechanical concentration by jigs, tables or other concentrating devices suitable for heavy ores, to make a satisfactory concentrate. At the Snow Hill Coal Corporation's plant in Indiana and at the Midland Electric Corporation's plant at Xtkinson, Ill., the final concentrate is made by a mechanical jig. The most recent and complete mill for concentrating pyritc from coal-mine refuse is that of the Mineral Products Co. at West Mineral, Kans., in which jigs and tables are used. Many regrinds and recirculations of products are necessary to get a concentrate of uniform grade. Trends On the whole, the economics of recovering pyritc from coal is not favorable. Cer-

Jan 1, 1948

By J. J. Bodmer

The substances or materials employed in this manufacture, are the same as those used in the preparation of mortar and concrete, viz., the different kinds of lime and sand. Instead of, or in conjunction with, sand there may be used calcined clay, blast-furnace slag, clinkers or ashes from furnaces, natural puzzolana, powdered chippings from stone quarries, etc. Of the different kinds of sand, pitsand—siliceous sand, as it commonly occurs mixed with gravel—and the sand found on the seashore, where the salt has been washed out by long exposure, whilst out of reach of the tide, may be used. The purer the above-named materials are from admixtures of clay, earth, or organic substances, the more complete will be their combination with the lime, the quicker will the manufactured brick or block set, and the more satisfactory will be the quality which it ultimately attains. For this reason, subdivided blast-furnace slag is preferable in most cases to sand, and the only sand which, in reference to setting capacity, is analogous to blast-furnace slag, is the volcanic sand occurring in different localities in North and South Wales, as an almost pure calcined silica. The lime used for the manufacture may be either slaked or unslaked. In the first case, (slaked), in order. to obtain satisfactory results, the lime must be strongly hydraulic. The use of unslaked lime, however, is by far preferable. A process for using fresh or unslaked lime has been patented in England by Major-General Scott. Lime thus prepared is called " selenitic lime," and consists of a mixture of fresh (unslaked) lime with sulphate of lime, or plaster of Paris. The graystone lime, for instance, found by the Medway, is mixed with from 5 to 7 per cent. of plaster, which has the effect of keeping the lime from slaking when water is added. This mixture also partakes of the nature of cement, and when used for mortar, or concrete, attains in a shorter time a greater degree of hardness than the same lime would ever have obtained after being slaked. Bodmer's process for the manufacture of artificial stone bricks consists chiefly in the use of automatic measuring, forwarding, and mixing apparatus, by means of which the materials are supplied and unite in a continuous stream, and are accurately measured. They

By N. W. Perry

Some months ago a gentleman gave me a handful of minerals which he had collected in an arroyo, or dry stream-bed, that ran through the town of Ramos, State of San Luis Potosi, Mexico, as a sample of the class of ore that might be expected in the mines of that section. I was, however, familiar with those mines and their ores, and cast the pebbles aside as of no interest. I afterwards returned to Mexico and took charge of two groups of mines, one in the State of Zacatecas, and the other in the town of Ramos, State of San Luis Potosi. While I was thus engaged, it was a very frequent occurrence for parties to bring me specimens of rock, ores, etc., for my opinion on them; and one day a man brought me a half-dozen or more small pieces of a very black shiny mineral, desiring to know what it was. I did not recognize it, and desired him to give me the specimens for analysis, which he promised to do in a day or two. He never did give them to me, for he lost them ; but he said there were plenty more where these came from—at Ramos—and he could get them at any time for me. I thought no more of the matter until after my return to this country, when, one day, in looking over some of my old " trash," I came across the specimens at first referred to as having been cast aside so carelessly. I noticed two distinct minerals among the pebbles : one being erubescite or tetrahedrite, the predominating mineral of the mines of Ramos, and the other a hard black shining mineral, the same that I had wished to analyze in Mexico. On testing for hardness I was surprised that it scratched topaz with some degree of ease, thus placing it above 8 in the scale of hardness. Trying it with a corundum, I sometimes succeeded in scratching it, but at other times it would scratch the corundum, and at still other times neither would produce the slightest effect on the other. Crystallized topaz would be ground to a powder in attempting to scratch the black mineral, without abrading it in the slightest. It must, therefore, be placed at 9 in the scale of hardness. It is of the deepest opaque black, not unlike pitch-blende in ap-

Jan 1, 1884

By J. J. Bodmer

THE substances or materials employed in this manufacture, are the same as those used in the preparation of mortar and concrete, viz., the different kinds of lime and sand. Instead of, or in conjunction with, sand there may be used calcined clay, blast-furnace slag, clinkers or ashes from furnaces, natural puzzolana, powdered chippings from stone quarries, etc. Of the different kinds of sand, pit-sand-siliceous sand, as it commonly occurs mixed with gravel-and the sand found on the seashore, where the salt has been washed out by long exposure, whilst out of reach of the tide, may be used. The purer the above-named materials are from admixtures of clay, earth, or organic substances, the more complete will be their combination with the lime, the quicker will the manufactured brick or block set, and the more satisfactory will be the quality which it ultimately attains. For this reason, subdivided blast-furnace slag is preferable in most cases to sand, and the only sand which, in reference to setting capacity, is analogous to blast-furnace slag, is the volcanic sand occurring in different localities in North and South Wales, as an almost pure calcined silica. The lime used for the manufacture may be either slaked or unslaked. In the first case, (slaked), in order to obtain satisfactory results, the lime must be strongly hydraulic. The use of unslaked lime, however, is by far preferable. A process for using fresh or unslaked lime has been patented in England by Major-General Scott. Lime thus prepared is called " selenitic lime," and consists of a mixture of fresh (un¬slaked) lime with sulphate of lime, or plaster of Paris. The gray-stone lime, for instance, found by the Medway, is mixed with from 5 to 7 per cent. of plaster, which has the effect of keeping the lime from slaking when water is added. This mixture also partakes of the nature of cement, and when used for mortar, or concrete, attains in a shorter time a greater degree of hardness than the same lime would ever have obtained after being slaked. Bodmer's process for the manufacture of artificial stone bricks consists chiefly in the use of automatic measuring, forwarding, and mixing apparatus, by means of which the materials are supplied and unite in a continuous stream, and are accurately measured. They

Jan 1, 1874

By E. A. Calnan, B. E. Williams

IN the development of a new treatment for the prediction of deformation textures,'-' it was noted that for no metals are there experimentally determined tension textures with which the predictions may be compared. There is a considerable knowledge of drawing textures and previous workers have been content to consider these as equivalent to tension textures for the purposes of comparison. It is shown, however, in the new treatment that the tension and drawing textures are not necessarily identical, the radial compression exerted by the dies in the drawing operation producing some modification of the tension texture. In particular for the face-centered cubic metals it is predicted that for drawing the final texture should be [1ll] with a spread towards [211] (a more detailed derivation of this texture has been made by Calnan3). This has been amply confirmed by experiment, see Hibbard.6 For the pure tension case, however, the treatment predicts intermediate [1ll] and [loo] textures leading to a [211] end-point, while all previous treatments have predicted the final texture as [1ll] with in some cases an additional [loo] component. Thus evidence that the pure tension end-point is the [211], or at least that [1ll] and [l00] are not the final textures, should provide a valuable test of the new treatment. Accordingly some experiments were made on aluminum. Three aluminum specimens were examined in detail, one of cold-rolled high purity rod (99.99 pct), specimen A, and two of commercial extruded rod of purity 99.4 pct, specimens B and C. The initial annealing treatments were: A, 1½ hr at 400°C; B, 2 hr at 400°C; C, 1½ hr at 650°C. The principal difficulty is that of obtaining sufficient elongation before fracture occurs. This was overcome to some extent by giving a softening heat treatment, 1 hr at 300°C, after each 15 pct of extension. Vickers hardness measurements gave values before and after the softening treatment of about 30 and 28, respectively, in comparison with the initial value of about 19 corresponding to fully annealed material. From recent observations in this laboratory it is concluded that this small recovery corresponds to a polygonization process rather than recrystallization proper and consequently the preferred orientation is unaffected. At the higher extensions, however, some slight necking of the specimens took place and it was necessary to turn them down to a uniform cross-section before

Jan 1, 1953

By P. Crowther, G. J. Lamprecht

The solubilities of silver, zinc, and cerium in liquid sodium, in the temperature ranges 100 to 270°C, 190° to 550°C, and 120" to 460°C, respectively, have been determined. From the solubility data the heat the entropy the partial molal enthalpy of mixing the excess entropy and the partial molal free energy of solution for the systems Nu-Ag and Na-Zn have been calculated. For the system Na-Ce the observed negative is discussed in terms of the solubility of the oxide Ce2O3. In an earlier publication the results obtained in the study of the solubility of tin' in liquid sodium are presented, as well as the detailed analytical procedures used. 1) REAGENTS Spectroscopically pure metals as supplied by Johnson Matthey and Co, were used to produce the following tracers: 253-day Ag110, 245-day zn65, and 325-day ce141. The tracers were prepared by irradiation in a thermal neutron flux of 4 x 10 13 neutrons cm-2 sek-1. To obtain a uniform amount of the required specific activity, needed for each solubility experiment, the radioactive metal was diluted with the corresponding inactive metal, by melting them together in an inert atmosphere. The liquid sodium used contained 11 ±2 ppm of O,1 determined by the vacuum distillation method.' The oxygen was assumed to be present as the oxide NaD. 2) THE SYSTEMS: SODIUM-SILVER AND SODIUM-ZINC Plots were made of the log of the mole fraction of silver, Fig. 1, and of zinc, Fig. 2, dissolved in the liquid sodium vs reciprocal absolute temperature. The equations for the solubilities, based on the least-squares fit to each plot, are: where Xi is the mole fraction metal dissolved in sodium, T is the absolute temperature, and s is the standard deviation in the value of log Xi. The heats and the entropies lution were calculated from the solubility data by In neither of the two cases was any intermetallic compound formed between sodium and the solute metal as was the case for tin.' Thus, for the silver and zinc systems the pure metal was taken as the reference phase. Since the solids in equilibrium with the liquid sodium were the pure metals, one can calculate the partial molal enthalpy of mixing and

Jan 1, 1969