Search Documents

By John D. Kalasky

Continuous mining has revolutionized the coal industry but intensified the problems of earlier mechanization. From the installation of the first miner, it was recognized that face ventilation would be one of these problems. To establish an efficient work cycle for the equipment being used, conventional mechanized mining provides four or more development faces. Continuous mining, relying on a single machine, requires only one face, although more than one can be driven alternately by the same machine. In gaseous areas mined by the older methods, the intermittent rate of exposure allows time for the face to bleed off or be cleared, and the width obtained with conventional units makes it possible to hang a brattice line almost to the face. Continuous mining increases the ventilation hazards; there is no margin of time, and very limited space.

Jan 9, 1959

Diversification has characterised the mining industry in this country and globally in recent decades, and in Western Australia in particular. One of the most obvious aspects of diversification is technological change which continues at a rapid and sometimes bewildering pace. A function of technological advances is the increased capacity to further diversify the range of minerals which can be identified in economic concentrations and profitably extracted. This broadening of the total base of the industry has a synergistic effect on its further development by extending its geographical spread and increasing scope for decentralised infrastructure. Another aspect of diversification is the corporate thrust towards establishing overseas mining bases for a variety of reasons. Off-shore (sea bed) mining is a further manifestation of increasing diversity, although very much in its infancy.

Jan 1, 1996

By R. Y. Wan, J. D. Miller

Thiohydrometallurgical systems including thiosulfate, thiocyanate and thiourea have been stud- ied as alternative liriviants for the leaching of gold. Research and development of thiohydrometallurgical technology has been prompted by environmental concerns with the use of cyanide and problems associated with the processing of difficult-to-treat ores. These thiosystems have some chemical similarities, enabling gold to be leached in a practical oxidizing environment. However, the solution chemistry of the thiosystems is complicated due to instability of the thioreagents and many other reactions which occur during the gold leaching reaction. In this paper, interference reactions of selected metal ions and sulfide minerals are examined in order to understand important aspects of solution chemistry which control the stability of the thioleaching reactions. Applications using thioreagents as lixiviants for oxide and refractory gold ores are presented.

Jan 1, 2005

By A Kindred

The Bogong Hydropower Development is a 140 MW high head power project currently under construction in Northern Victoria. The project is the final link in the Kiewa hydroelectricity scheme, which was originally constructed in the 1950s. Due to its location in the Alpine National Park, the waterway for the Bogong project must be located entirely underground. A series of shafts and tunnels is being constructed to transfer the water from the headworks at McKay Creek to the new power station located on the shores of Lake Guy in Bogong village. The difference in elevation between the headworks and the power station is greater than 420 m, which poses particular issues for the design and construction of the waterway. The purpose of this paper is to describe the design and construction planning aspects of the tunnelling and shaft excavation and lining works for the waterway. The tunnelling works includes 5.7 km of hard rock tunnel boring machine (TBM) driven tunnel, 1.1 km of drill and blast tunnel and two deep shafts. The tunnels and shafts are lined with a mixture of permanent rock bolts and shotcrete, concrete lining and steel lining. The viability of the Bogong Hydropower Development relies heavily on the ability of the TBM to excavate at high speed through the East Kiewa Grandiorites. Particular attention was given during the construction planning stage to understanding the excavation characteristics of this material, and designing a suitable hard rock TBM that would be capable of meeting the program requirements of the project.

Jan 1, 2008

By Peter Babik

"Cable TV networks are extensively used throughout Canada for TV signal distribution. Mobile/portable radio communications are also used extensively throughout all sectors of industry. There are numerous manufacturer supplying these industries with a wide variety of equipment and accessories.IAL's underground radio communications system combines the techniques of cable TV and mobile radio to produce a flexible communications system with most of the advantages of both systems. Standard off-the-shelf mobile, portable, base-station and repeater equipment can be used. The equipment may need modification to be customized to particular end user requirements, but does not require a complete new unit redesign. Likewise, the cable TV distribution equipment is off the-shelf, with some items requiring modification for underground system application.Radio communications can be provided wherever the cable system is extended. Where traffic or type of activity warrants it, multiple radio channels can be provided on the same cable. Certain radio channels could also be used with data channels for control or supervision of remote equipment or environmental conditions. In addition, the same cable can be used to distribute or monitor signals from remote TV cameras in selected or dangerous areas. The system can be interfaced to a telephone system, if required, to provide extended communications to above-ground workshops, offices, medical stations or even hospitals and other emergency services.IntroductionReliable communications among personnel throughout an underground mine area have long been the dream and goal of various mine operations personnel. The system to be described was designed to meet this objective."

Jan 1, 1983

By Edgar Stansfield

ONE of the most striking features of the coal series passing from peat through brown coal, lignite, etc., up to anthracite is the gradual reduction of moisture content with the increased coalification of the original plant material. Thus drained peat from a bog may contain 90 per cent water, brown coal contain 50 per cent, lignite 30 per cent, while a bituminous coal may contain only 1 per cent moisture. Moisture, therefore, is one of the important factors to be considered in coal classification, especially with the lower rank coals. With bituminous and higher rank coals the moisture content is less satisfactory for classification; it may even pass a minimum value and then increase with increasing rank to anthracite and superanthracite. Coal in an undisturbed seam contains moisture which is an integral part of the coal, but it may also be wet with free, underground water percolating through the seam. Only the former must be considered in evaluating the moisture content of the coal for classification purposes; this will be called the "true moisture" of the coal. When the seam is mined and sampled the sample taken may show the true moisture; on the contrary, it may contain in addition free mine water or, especially in dry, well ventilated mines, it may contain less than the true moisture. Coal contains unstable organic compounds which may decompose, with the production of moisture, when the coal is exposed to air at ordinary temperatures, or is heated with or without exposure to air. The potential moisture of a coal therefore is higher than its actual moisture. The lower the rank of the coal, the greater its instability, as a rule, and the greater the care necessary to avoid oxidation or decomposition in any investigation of moisture content. The majority of coal workers have preferred, on account of the difficulty in evaluating the true moisture of a coal, and for other reasons, to classify coals by analyses calculated to the dry-coal basis. A number of workers familiar with lower rank coals have recently insisted that the classification of such coals can be satisfactory only if analyses on the moist-coal basis are employed. The moisture-holding capacity of coal is therefore intimately connected with coal classification, and in this paper a procedure is outlined for determining the true moisture of a coal.

Jan 1, 1932

By Jacques H. Nantel, James F. Archibald

"Frozen tailings material may be required, in the future, to perform the support functions of underground backfill in mines located in zones of permafrost, notably in the high Arctic. To date, no knowledge of physical support parameters of such materials has been obtained in Canada due to the limited mining activity in permafrost regions. It is therefore judged essential that the important physical and mechanical properties relating to frozen tailings material be assessed.Innovative mining methods will be required to cope with the harsh environmental conditions that exist at mining sites in the Canadian Arctic. A preliminary laboratory study, in the absence of field trials at limited Arctic mining sites, has been completed in which the physical and mechanical properties of several types of representative mill tailings mixtures have been investigated. A variety of tests, to determine frozen slurry and pelletized tailings strength properties, moduli of compression, optimum water contents, deformation characteristics and the like, have been conducted.The results of this study will be used to establish guidelines for the suitability of tailings use in such northern mining environments. IntroductionFrozen tailings material has never been used to backfill underground openings in Canadian mines. At present only one Canadian mine, the Polaris Mine situated on Little Cornwallis Island, is investigating the use of frozen backfill. However, the Canadian North covers a large territory and potentially contains a large number of mineral deposits. The understanding of concepts related to mining activities in sub-zero frozen ground is therefore important.The implications of using frozen tailings as underground backfill material are far reaching both from the point of view of mine stability and disposal of tailings in the arctic regions.The strength of frozen materials (soil, backfill, etc.) may take on different meaning depending on the engineering situation. Both the concepts of rupture and excessive deformation need to be considered.The functions usually required to be performed by the backfill material in underground mines may be summarized asfollows:a) working floors; such as in cut-and-fill stopesb) stope wall support; for cut-and-fill and delayed fill stope~c) self-support when backfill is exposed on one face; during pillar recovery phases.For fill functions such as working floors, the short-term response of the frozen fill is the dominant concern. For the other fill functions, the long-term deformation response of the frozen fill, or creep, is of interest."

Jan 1, 1986

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Square-set timbering of stopes developed from stull support methods because veins too wide for stulling were being mined. In general, the void caused by the stoping of the ore is filled with a system of interlocking timbers. Timber framework supports the wall rock, the mining operations, and provides access. A timbered stoping method can be used in all widths of veins at any dip. The timbering can be normal and parallel to the planes of the walls or at angles to these planes. Irregularly shaped ore bodies can be worked by timbered methods. Pinching or swelling of the vein will not adversely affect the method. Timbered stoping is especially advanta¬geous where weak ground is encountered in the vein or the wall rock. The ground is unsupported only until timber sets are stood. These stopes can be filled with sand or waste when desirable. The customary method of developing a square-set timbered stope with haulage drifts above and below and timbered raises on each endline is shown in Fig. 1. The drifts are timbered the full stoping length. The raises have two compartments with the manway and timber slide in one compartment and the chute in the other. The drifts and the raises cannot be widely spaced as handling timbers is an important consideration. Stoping can begin immediately above the drift timber and continue in both directions and upward from the raise. Breasting down each blast round for only one timber set laterally is the common practice. The blasted ore falls to a lower floor where it is slushed or trammed to the chute. Drilling can proceed on the upper floor while broken ore is being removed from the stope. As shown in Fig. 2, square-set timbering may be used in cut-and-fill stopes to support the back and walls until fill is added. There are various ways of developing an ore block for timbered stoping. Fig. 3 depicts the situation for the main haulage in the vein with an intermediate drift separated from it by a sill pillar. The ore is slushed into the chute connecting the two drifts. The situation in Fig. 4 is identical to that in Fig. 3 except that no sill pillar is used. In Fig. 5, the haulage drift development is done in the footwall with crosscuts driven to intersect the ore body. The intermediate drift development is above the crosscuts with a minimal sill pillar. The main bottleneck in timbered stoping is in the timbering process. Drilling in the stope is generally held up while timbering is done. Two or three men are re¬quired to do the timbering and an additional one or two men are needed to transport and raise or lower the tim¬ber. Good organization is essential to timbering. Skill must be exercised in standing the timber to support the ground and still maintain good production. COSTS AND PRODUCTIVITIES Development and stoping costs are presented in Tables 1 through 7 for the situations in Figs. 3 and 5,

Jan 1, 1982

By R. J. Dippenaar

In his inaugural lecture (delivered in Afrikaans at the University of Pretoria on 16th February, 1995), Professor Dippenaar defends his doctrine, philosophy, objectives, and methodology, as was required of a newly appointed professor in the days of old. Briefly, he recounts the growth and achievements of the Department of Material Science and Metallurgical Engineering at the University of Pretoria; he sketches its strategic guidelines and the obstacles encountered; he outlines the opportunities for the metallurgical industry in South Africa and the need for environmental control; and he describes how modeling techniques, together with expert systems, can aid both the industry and the community. He ends on an optimistic note, saying that his Department will continue to strive to transform adversities into opportunities, and to give its students a view of new horizons beyond the foundations laid by their teachers.

Jan 1, 1996

Because the Australian resource industry differs from the resource industries of other countries, direct application of manpower planning processes derived from overseas experience may be singularly inappropriate for Australian projects. Too often in Australia, project manpower planning has been undertaken as an afterthought to technical and financial analysis. A wide variety of complex and interrelated manpower considerations should be evaluated from the beginning of project planning, even at feasibility study stage, and relevant deductions should be incorporated into all other planning. Many manpower factors can be considered sequentially but it is probably necessary to undertake critical path analysis for manpower planning. The paper highlights some key factors involved in project manpower planning and suggests a simple linear planning sequence which integrates the analysis of factors and can in turn be integrated into technical and financial planning.

Jan 1, 1983

By Richard R. Klimpel

INTRODUCTION The purpose of this paper is to summarize the current status of reagents used in the mineral industry plus present some current challenges and possible new technologies of the future. Table 1 lists the important families of reagents which, when taken together, constitute at least 95% of the current commercial reagent market. A very approximate estimate of the free world reagent market size in mineral applications is about 1.5 to 2.0 billion dollars (U.S.) using 1985 data. Obviously, to serve such a large market requires the effort of many different types of commercial supply sources. It is estimated that there are over 300 industrial firms in the free world that have a dedicated business/technical structure for supplying reagents related to the mining industry. There are a number of characteristics which are associated with the product families listed in Table 1. Understanding these characteristics helps to provide a realistic economic/technical basis for outlining future challenges in mining chemicals. 1.Essentially all of the products listed are old chemistry in the sense that the molecules have been known and manufactured for at least 25 years. This has not been a highly dynamic field of endeavor from the viewpoint of new product introduction. 2. The greater majority of the products listed can be viewed in commercial terms as "commodity" chemicals, that is, they are available from many sources and the pricing of a some- what generic product generally dominates differences in product quality or uniqueness. With commodity pricing, reagent suppliers significantly reduce research expenditures, loosen product quality somewhat if the applications of the reagents allow, etc. in order to be cost competitive.

Jan 1, 1989

By Greg Halsted, Joshua Gilman

Today's civil and geotechnical engineers play an important role in helping to achieve sustainable infrastructure. To address environmental sustainability and climate change caused by green- house gas (GHG) emissions, all engi- neers must adjust their traditional approach to materials, design and construction practices to include a focus on minimizing carbon dioxide emissions. The considerable influence that geotechnical engineers have on projects provides an important oppor- tunity to affect positive change. The carbon footprint of the construction methods and materials used for foun- dations can be as much as 8-9% of a new building's total carbon footprint, and geotechnical engineers have an op- portunity to evaluate alternatives based not only on cost, but also the long-term environmental impacts. Growing environmental considerations and societal concerns are influencing the selection of construction materials and methods, including cement and concrete's role and significance for infrastructure applications today and in the future.

Jan 1, 2023

By Roger L. Keller

Cautious, productive blasting is employed in the adaptation of a mobile crushing system extending into a highway through cut. In Hong Kong's final chapter of infrastructure development in preparation for handover of sovereignty, the vital link to the new governing country, The People's Republic of China, is now being completed. The Ting Kau approach and Tai Lam tunnel involves the removal of 6 million cubic meters of rock by drill and blast means. For the main-cut excavation (because of removal Iogistics) a unique adaptation of a Lokotrack crushing and conveyor transfer system is being used. The characteristic narrow working area associated with through cuts, positioning of equipment, and production demand place many limiting factors on blasting. Add to this the strict criteria set by the local regulatory body, the Hong Kong Mines Division, and nearby vibration limiting structures (13mm/sec), has led to highly cautious, fine-tuned blasting.

Jan 1, 1998

By G. Vibert Douglas

THE prospecter and geologist in the field, in the search for gold, are very often faced with a real difficulty. The: mineralized rock _frequently contains gold which is so finely divided or associated with sulphides that it is not recognizable in the gold pan. In recent years, the practice has been to take samples, send them to an assay office, and sit down and wait for results. This paper describes a method of solving the difficulty of proving the presence of this fine gold. The investigation is still in an experimental stage; but certain results have been obtained which would seem to justify publication. We do not consider that the method outlined is quantitative, but we believe that qualitative results are assured. The procedure has the great merit of simplicity. A sample of approximately two pounds of the mineralized rock should be taken and powdered as fine as is practicable. This powder is theo panned and the heavy minerals concentrated. Approximately two grams of these concentrates are taken for the test (one gram can be roughly gauged in the field by heaping up the powder on a Canadian twenty-five cent piece). The material is placed in a test-tube and 6 c.c. of a 10 per cent solution of iodine in alcohol are added (one-third of a test-tube full is approximately equal to 6 c.c.). Heat gently for about ten minutes over a spirit lamp, but without actual boiling. Allow to stand undisturbed until the sediment has settled to the bottom. Remove the clear iodine solution with an eye dropper. Allow it to fall, drop after drop, on a warmed pyrex watch-glass (the drops should be of equal size), taking care that the successive drops fall in the same place and that each drop evaporates before the next drop falls. Heat is applied to the lower side of the watch-glass by means of a spirit lamp. If gold is present in amounts of $2.00 or more per ton, a gold mirror will be formed on the watch-glass. This process of dropping and evaporating should be continued until no clear solution remains. If no mirror has appeared when all the solution has been used, another 6 c.c. of the iodine solution should be added to the powder and the process repeated. The absence of a mirror after the double treatment denotes an amount of gold less than two dollars per ton at the present price, or that the ore contains no gold. The mirror obtained must be washed with nitric acid ( 1: 1) to remove any copper, silver, lead, zinc, and iron. The yellow mirror remaining is pure gold.

Jan 1, 1937

By R. Karl Zipf, Christopher Mark

Highwall mining continues to grow in importance as a coal production method from U.S. surface mines. It may account for as much as 4% of the total U.S. coal production, according to one recent estimate. Analysis of Mine Safety and Health Administration (MSHA) accident and injury statistics shows that, overall, highwall mining has maintained an admirable safety record. Its fatality and injury rates are comparable to those for other surface mining methods, and are significantly lower than those for underground mining. No mining method is risk free, however. Highwall mining injuries have been associated with handling materials, slips and falls, machinery, powered haulage, and other types of incidents. But perhaps the greatest risk, to both personnel and equipment, is from ground control. The two most significant ground control hazards are rock falls from the highwall and equipment entrapment underground. Highwall Stability Ensuring highwall stability through proper ground control engineering is of paramount importance to safe highwall mining operations. The only fatality to occur during the last five years at a highwall mining operation was due to highwall collapse. There have also been numerous near-misses, several of which have involved extensive damage to equipment. In the central Appalachians, where the majority of highwall mining occurs in the U.S., hillseams are the most prominent geologic structures that affect highwall stability. Hillseams (or mountain cracks) are near vertical fractures in the rock that are formed in response to natural weathering and erosion of hillsides. They extend hundreds of feet down from the surface. They typically run parallel to the hillside, but they can also extend across narrow points or ridge lines. The hazard arises when rock slabs that form along the hillseams detach and fall away from the highwall face (See Figure 1). [ ] Unfortunately, it is impossible to control the location of hillseams or reliably detect their presence within a highwall. There are, however, a number of measures that can be taken to minimize the risk of failure associated with hillseams: Planning-Most operators choose to skip those areas of the highwall where a prominent hillseam daylights (See Figure 2). Existence of such areas is known for several weeks in advance of highwall mining; therefore, planning engineers can adjust the layout of highwall mining panels to locate barrier pillars within areas of questionable highwall stability. [ ] Inspection and monitoring-Daily inspection of the benches above the active highwall mining area is a prudent precautionary measure. A crack in a bench immediately above a highwall miner is shown in Figure 3. Simple displacement monitors may be useful for detecting movement along cracks that may precede a significant life-threatening failure. New tools, such as slope monitoring radar, may also prove useful in detecting motion of the rock slopes above active highwall mining operations. Good blasting practice-Most surface coal miners in the central Appalachians use pre-splitting and the familiar halfbarrels are routinely seen throughout the pits. Shorter delays along the face and longer delays between rows can direct more of the blast force parallel to the face, potentially doing less damage to the wall rock. In addition to pre-splitting, decreasing the burden, spacing and charge weight in drill holes close to the highwall will also decrease damage to the wall rock. Decreasing the highwall slope angle-Decreasing the highwall slope angle from 90° (vertical) to 70°-80°, especially in areas of known hillseam concentration, could eliminate the hillseam hazard (See Figure 4). Angled highwalls are routinely employed in many Midwestern surface mines and in some

By L. B. Pankratz

Thermodynamic data on the elements, oxides, sulfides, halides, and selected hydrides, carbides, nitrides, carbonates, sulfates, silicates, and miscellaneous compounds were reviewed, evaluated, and compiled at the Bureau of Mines. Values for CP°, S°, H° -H°298, ?Hf°, and ?Gf° are given in tabular form. A brief thermodynamic background and a number of examples and applications are presented.

Jan 1, 1984

Report of Secretary TO THE BOARD OF DIRECTORS OF AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen -I have the honor to present the following report for the calendar year 1920 The activities which-seem to call for special com¬ment are THE NEW FORM OF MAGAZINE MINING AND METALLURGY appeared every month during the calendar year and has been developed until it contains some ten departments It has brought forth more commendatory letters than have been received at headquarters on any other subject throughout the year Less than a dozen letters unfavorable to the change have been received, and the indications are that the magazine has met a want deeply felt, especially by members distant from headquarters The technical papers printed by the Institute are published in abstract in the magazine and opportunity is given to members who desire them to receive full copies of any or all papers published The Bound Volumes, as usual, contain all the papers in full and discussions thereof FINANCES The greatly increased cost of paper and printing has put a tremendous burden on the Institute's finances, since the dues of $12 per year are only 20 per cent greater than the members paid when the Institute was founded forty-nine years ago This has resulted in a temporary deficit, similar to that encountered by many of our sister engineering societies The fact that our Institute has lower dues and gives more in the way of publications to its members than any other of\the national engineering societies has rendered the situation more difficult for us MEETINGS The Annual Meeting in New York, the Field Meeting in the Lake Superior District, the meeting of the Petroleum and Gas members at St Lours, and of the Institute of Metals Division in Columbus, Ohio, have all been described in full in the magazine

Jan 1, 1923

By Glenn A. Gruber

The conditioning of phosphate flotation feed with anionic flotation reagents was identified as a high- priority research topic during a beneficiation work- shop sponsored by the Florida Institute of Phosphate Research (FIPR). FIPR subsequently solicited research proposals to identify the mechanisms of reagent adsorption, to determine scale-up relationships for conditioner design, and to investigate the effect of conditioning variables on reagent adsorption and flotation performance. The two-year research project was awarded to Jacobs Engineering. Somasundaran, Inc., the University of Florida Mineral Resources Research Center, and the U.S. Bureau of Mines assisted Jacobs. Two mechanisms of anionic collector adsorption were detected by spectrographic analyses and confirmed by microcalorimetric measurements. The mechanisms provided a sound technical basis for the empirical practice of conditioning phosphate flotation feed at a high percent solids. Tests performed in laboratory and pilot-scale agitated tanks indicated that power intensity may be used as a reliable scale-up parameter for anionic conditioning of phosphate slurry. Excessive agitator speed during conditioning was found to be detrimental to anionic flotation performance. Some dimensional ratios of anionic conditioners were found to be consistent with good utilization of agitation energy. Laboratory conditioning and flotation tests demonstrated that adsorption of collector onto phosphate and the subsequent recovery of phosphate in anionic flotation were significantly influenced by the quantity and quality of water used in conditioning. Conversely, the quality of water used in flotation was more influential on the recovery of quartz in the concentrate. A comprehensive survey of anionic conditioners and conditioning practice in the Florida phosphate industry was also performed during this project. The study clearly showed that flotation testing with laboratory conditions typical of scientific research gives different results than laboratory testing with simulated plant conditions. The effects of test conditions on laboratory test results should be carefully considered by investigators planning and conducting applied research.

Jan 1, 1999

By Paul L. Goddard, Alfred G. Hoyl, William R. Sirola

A good place to look for elephants is in elephant country, and old mining districts are certainly elephant country as far as minerals are concerned. In many areas probably more ore is still in the ground than has been taken out. The old timers were good miners and hard workers and when they left ore behind, it was usually for good reason; but many an old mining district has been revived by new approaches to old problems, taking advantage of new techniques and new equipment. One of these is the Front Range mineral belt of Colorado, which has produced minerals for the past 100 years through the ups and downs of mineral prices and the general economy. Gold, silver, copper, lead, and zinc have been found in abundance in the complex sulfide veins of the area. Between Idaho Springs and Central City lie several strong veins which have been mined successfully in the past. The two strongest of these veins, striking northeast-southwest, (Lake-Bald Eagle), and northwest-southeast, (Crown Point-Belman) , and dipping northeast and northwest, respectively, intersect in a flat X near the head of Virginia Canyon. From the lowest drainage of the area, Clear Creek Canyon, the old timers drove the Central, or Big Five, haulage-drainage tunnel due north. It intersects the two veins 8460 ft from the portal and 1670 ft below the surface. The two veins were mined successfully at the surface and at the tunnel level. Without an opening to the surface at the in- side end of the tunnel, ventilating became very difficult as the stopes were opened up, and mining ceased in 1929. Vertically, 1200 to 1600 ft of virgin ground remains in the veins.

Jan 6, 1959

By W. A. Bruce

THIS paper presents the essentials of a mathematical method of studying the pressure behavior of an oil reservoir as the fluids are withdrawn. Methods are shown whereby the behavior of a reservoir can be used to predict the future relationship between withdrawals and pressure. The oil reservoir is considered as a small part of a large porous continuum, which contains for the most part water. The expansion of this water resulting from a decrease of pressure in the oil zone causes a movement of water that is an important factor in the relationship between fluid withdrawals and reservoir pressure. Examples are given to illustrate the methods of pressure prediction for a circular reservoir containing undersaturated crude, the pressure distribution over a field that has a uniform production rate, the effect of a fault line near a field, the mutual interference of near-by fields, and the perturbing influence of a gas cap. Applications of the analysis to sell-spacing problems are shown.

Jan 1, 1942