Search Documents

By R. Hagemeyer

In North America, the paper industry is by far the largest consumer of coating and filler mineral pigments. Present use is at an annual rate of 5.5 million metric tons with a value of $660 million. Current estimates are 65 percent is used in coating and 35 percent in filler applications. During the past decade, the switch to alkaline papermaking has provided the opportunity to substantially increase filler levels while maintaining paper strength. As a result filler consumption has been growing at a late in excess of 15 percent yearly. Unfortunately, within a few years, mandated recycling could slow or even reverse this trend. The critical issue is finding an economically viable method for recycling the mineral pigment and/or minimizing the disposal problem

Jan 1, 1994

By Joe M. Bryan, George E. Rodger

The development of small precious metal mines in the western states has been directed at heap leach operations. Crushing plants are an essential adjunct to heap leach operations. They must meet environmental air quality regulations which generally follow a similar pattern from state to state. Prior to mine construction a permit must be obtained and an operating permit granted during or shortly after the start-up period. The typical construction permit application consists primarily of drawings, specifications and an explanation sufficient to indicate that the mass of particulate matter entering the atmosphere is below minimum standards. The operating permit may be granted following demonstrations that air emission control equipment or methods comply with information submitted in the construction permit application.

Jan 1, 1987

By R. Harris, M. Misra

Column flotation technology has a demonstrated potential for recovering clean coal from high-ash waste fines. The effect of different variables such as air flow rate, frother addition, depressant addition, percent solids and particle size on the quality of separation are discussed. Results indicate that air flow rate and depressant addition are the important variables which control the selectivity in the flotation of fine coal in a column cell. Separation efficiency achieved with column cells is significantly better than that with conventional flotation cells. Under appropriate experimental conditions with a deep column, more than 80 percent coal can be recovered in the concentrate containing 10 percent ash from waste fines containing over 60 percent ash.

Jan 1, 1988

By Tuomas van der Meer, Jukka Tanninen, Annukka E. Mäkinen, Mika Martikainen, Laura M. Nevatalo

The mining industry consumes huge water volumes and the waste streams typically contain sulfate, which has caused problems to many operations around the world. Discharge of sulfate to fresh waters is being restricted as the sulfate load increases salinity and causes problems when sulfate is reduced to toxic H2S by natural bacteria. To reduce fresh water consumption, internal water recycling had become a necessity in metallurgical processes. However, the recycling causes accumulation of sulfate and other components in water, causing problems to process performance and increases scaling in piping and equipment. Few technically feasible water treatment processes exist in the market that can be applied to decrease sulfate concentration below gypsum saturation level: biological sulfate reduction, membrane separation, ion exchange, evaporation and chemical precipitation. Some of these technologies are effective for treating wastewater, but there is typically a highly concentrated sulfate fraction left requiring still further treatment. Outotec has developed a sulfate removal solution, Outotec Ettringite process, which allows flexible control of residual sulfate concentration, thereby opening doors for increased water recycle within processes and control of the sulfate in discharged waters. In this article the results and benefits of this novel process along with examples of operating costs are presented.

Jan 1, 2014

By Dion Weatherley, Raúl Castro, Pablo Cid, René Gómez

In underground mining, hang-ups due to coarse fragmentation are frequently observed in drawpoints, drawbells, and ore passes during ore draw. Hang-ups can often require operational interference and hang-up removal activities. Drawpoint and drawbell design has been shown in some studies to influence hang-ups; however, the full extent of this influence remains open to question. In this study, the discrete element method was used to analyze the effect of hang-ups on three distinct drawbell geometries: the Drawer type, Circular type, and El Teniente type. The drawer type was used as the base case given that data was available from a physical model in which hang-ups were studied. The drawer type base case data was then used to calibrate our numerical model. Results show that the El Teniente drawbell geometry sustained 13% more hang-up events as compared with the base case, while the circular drawbell geometry had 16% fewer hang-up events than the base case. From this study, it can be concluded that fewer hang-up events will occur with a rounded drawbell geometry.

Apr 11, 2023

By Shinya Otsuka

Activity coefficient of oxygen in sulfide-rich and metal-rich melts in copper-sulfur binary were determined at 1423 and 1523 K by means of a modified coulometric titration technique using the following cell: 0 ( is Cu-S melts) I Zr02 (+Ca0) I air, Pt The activity coefficient values obtained in the present study increase rapidly with sulfur composition in the vicinity of xs = 0.3333. The data obtained for the matte saturated with the metal-rich melts are in good agreement with those obtained by Kuxmann and Benecke, Schmied 1, and Eguchi and Yazawa. Those obtained for the metal-rich melts are in good agreement with the results of Sano and Sakao.

Jan 1, 1983

By Sidney Katell

An estimated capital investment of $76,499,800 will be required for a plant designed and built to produce 90 million standard cubic feet per day (std.c.f.d.) of synthetic pipeline gas through Lurgi gasification of bituminous char. This investment figure does not include the pretreatment plant, the cost of which is assumed to be reflected in the cost of the char fed to the gasification system. Shift conversion, C02 removal, and methanation are required after gasification in the Lurgi unit to make a gas suitable for pipeline transmission. Capital investment data are based upon equipment costs, January 1959. Based on a 90-percent or 330-day operating year, the operating cost before profit and Federal taxes with the char price as a variable will amount to the following: [ ]

Jan 1, 1959

By T. Avilez, D. Salari

"The economics of developing gold deposits containing elevated levels of cyanide soluble base metals is often challenged by high cyanide consumption and increased operating costs. SART is a chemical process that enables cyanide consumed by base metals to be recovered and recycled for gold leaching. The process also provides concurrent recovery of the base metal to generate incremental revenue from the sale of high-grade base metal sulphide concentrates. Although SART was developed and successfully piloted by Lakefield Research and Teck Corporation in the late 90’s and is now a public domain technology, the adoption of SART has been relatively slow due to concerns about implementation costs and the reliability of metallurgical performance. Through extensive experience in selective metal sulphide precipitation applied to mining wastewater since 2007, BQE Water has provided process know-how, design along with operations and maintenance experience to a number of projects involving the integration of SART into various metallurgical flowsheets on an industrial scale. This paper presents the commissioning experience and operating data from a SART plant treating up to 500 m3/hr of leach solution at a heap leach operation in Mexico. INTRODUCTION One of the current trends in the gold industry globally is the increasing importance of complex polymetallic gold deposits as discoveries of large Carlin type gold deposits become increasingly rare (Sceresini, 2005). The presence of cyanide soluble copper and zinc in complex gold deposits necessitates changes to the traditional gold extraction metallurgical flowsheet. A tool available to the industry to help manage the interference of cyanide-soluble base metals in gold extraction is the SART (sulphidization-acidification-recycling-thickening) process. SART breaks the weak acid dissociable (WAD) base metal-cyanide complexes, precipitates the metals as high-grade sulphide concentrates and makes the freed cyanide available for recycle."

Jan 1, 2018

By J. E. Gray

Before specifications are discussed it may be well to define the term "Mineral Aggregates." Professor K. B. Woods (1) defined "Mineral Aggregate--An aggregation of sand, gravel, crushed stone, slag, or other material of mineral composition used in combination with a binding medium to form bituminous and portland cement concrete, macadam, mastic, mortar, plaster, etc., or alone as in railroad ballast, filter beds, and various manufacturing processes, such as fluxing, etc. " This definition is too all inclusive for the purposes of this paper; therefore, this discussion will be confined to specifications for natural aggregates which means sand and gravel and crushed stone, and limited primarily to coarse aggregate which is aggregate larger than one-quarter inch in size. To the uninitiated, this may seem to be a very limited subject on an unimportant material. However, aggregates are essential in all types of construction. The tonnage and value of these two aggregates produced in the United States during 1959 as reported by the Bureau of Mines were as follows: Sand and Gravel 729,895,000 tons valued at $728,527,000 Crushed stone 581,721,000 tons valued at $824,411,000

Jan 1, 1961

By GEORGE S. POPE

The purchase of coal by the Government under specifications depending on the heating value of the coal, its content of ash and of moisture, and other considerations, rather than upon the reputation or trade name of the coal, was based on the fuel investigations begun by the Technologic Branch of the United States Geological Survey in 1904. The plan was first adopted by the Treasury Department in 1906. Since then the plan, variously modified in form but the same in principle, has been gradually adopted by other departments until at present of the coal used by the Government, the total value of which approximates $8,000,000 annually, more than half is purchased under specifications. The Government publications dealing with the adoption by the Government of the specification plan, the number of contracts awarded on that basis, and the quality of the coal delivered under such contracts in the several fiscal years covered by the reports are given in publications listed at the end of this bulletin. Under the authority of acts of Congress making appropriations for analyzing and testing fuels belonging to or for the use of the United States Government, a laboratory is maintained at the headquarters of the Bureau of Mines, Washington, D. C., where samples represent- ing deliveries of coal purchased under specifications for Government use are analyzed and tested. At this laboratory more than 1,200 samples have been analyzed and tested in one month. With the complete equipment and the efficient force employed, the analytical work has been so perfected that the analyses and heating-value tests of the samples received are as accurate as may be reasonably expected in laboratory work of this nature. One of the serious drawbacks to the general adoption of the speci- fication method for the purchase of coal is the difficulty of obtaining at reasonable cost samples of coal that can be considered fairly repre- sentative of the commercial product delivered in wagons, railroad

Jan 1, 1913

By Robert Jacob Cefalo

In 2019, the Bingham Canyon Mine, owned by Rio Tinto Kennecott Utah Copper Company, mined through the active underground that dewaters the pit. The active underground required the limitation of vibrations to avoid catastrophic damage or damage that would require work to the shotcrete and additional roof support. The surface design of the current sector was mined next to and through portions of the active underground.

Feb 1, 2020

By J. Chupak, D. J. Salley, G. L. Simard

Radiotracers were demonstrated to be of considerable value in a study of the interaction of dithiophosphate with galena. The interaction had characteristics of both chemisorption and chemical reaction, being complex because of the nature of the galena surface. Sorption was rapid and markedly reversible, and flotation occurred at relatively small amounts of dithiophosphate sorbed.

Jan 1, 1950

By Lixue Wen, Jun Xiao, Dongping Shi, Yan Xue, Jinmiao Wang

Mine ventilation energy consumption is one of the main sources of energy consumption in mining production, accounting for about one-third to one-half of the total energy consumption. Therefore, reducing the energy consumption of the mine ventilation system is crucial for mining production. With the premise of meeting the airflow requirements of the underground work areas and achieving sustainable development of mining production, this paper establishes a nonlinear optimization mathematical model for the mine ventilation network with the objective of minimizing the total power. Regarding the model, optimization of the decision variables was carried out using the method of minimum spanning tree. The constraints for air flow balance, wind pressure balance, and fan operating conditions were optimized using the exterior penalty function method, thereby transforming the model into a nonlinear unconstrained model. Based on this model, a modified sooty tern optimization algorithm (mSTOA) was proposed to achieve optimization. Improved the sooty tern optimization algorithm (STOA) by using the uniform reverse strategy, fitness value-distance balance selection strategy, and mutation strategy. The STOA, mSTOA, and three other classical optimization algorithms were applied to the optimization of a ventilation system of an actual mine. The experimental results show that after using mSTOA to optimize the ventilation network airflow distribution in the mine, the total energy consumption can be reduced by about 35.06% while meeting the constraints and demands of the ventilation network regulation and usage. This is of great value to mine roadway operation environment safety and clean production.

Dec 20, 2023

By Hazal Melis Aytac, Lana Alagha, Fardis Nakhaei

Gallium (Ga) and Germanium (Ge) are essential strategic elements that are extensively used as semiconductors in many technological fields. Owing to their essential uses and supply disruption, Ga and Ge are deemed critical by the U.S. They are typically found as substitutions or inclusions in zinc minerals. However, their distributions within zinc minerals are not well understood. To address this, trace element and mineralogy analyses of representative samples obtained from an old high-zinc-grade tailing were performed using various qualitative and quantitative techniques. These techniques included Inductively Coupled Plasma Mass Spectrometry (ICP-MS), Tescan Integrated Mineralogical Analysis (TIMA) with Scanning Electron Microscopy (SEM) and X-ray Diffraction (XRD). Moreover, bench-scale froth flotation tests were conducted to enrich zinc minerals, the major hosts of Ga and Ge, using PAX as a collector, Na2S as a sulfidizer, Pb(NO3)2 as an activator, and MIBC as a frother. Comprehensive characterization analyses of the flotation products showed significant enrichment of Zn, Ga and Ge in the flotation concentrates.

Feb 1, 2025

By O. W. Owings

"The handling and transportation of explosives and explosives supplies are inherently hazardous owing to their sensitiveness to impact and flame or electric arcs and sparks. Many accidents have occurred in the past during transportation of explosives, especially when they were carried by individual miners on man-trips. When electric haulage became the usual mode of transportation and shots were fired electrically, the hazards of carrying explosives and supplies on man-trips were fully realized, and in some mines all explosives were placed in one car, usually at the rear of the trip. Far-sighted managers saw the danger of this practice and provided separate trips for delivering explosives. This step was a definite advance in safety, but the latest achievement is the construction of special, rugged, nonconducting cars.Many coal-mining men have shown considerable interest in the construction of safe cars for explosives during recent months. Undoubtedly many others are interested in this phase of safety, therefore this circular is issued to give information on cars of this type now in use.Car A (fig. 1) is essentially a closed inner box separated from an outer box by an insulating lining of rubber. The double box is attached to a standard steel chassis that has spring journals and electric welding instead of certain rivets. The chassis is equipped with roller bearings. The over-all length from pin to pin is 11 feet, 9 inches; the wheel base is 54 inches, the track gage 42 inches, and the capacity eighteen 50-pound cases of permissible explosives. The box is 10 feet long, 6 feet wide, 3 feet high at the top of the arched roof, and 2 feet 9 inches at the edges. The top of the car is 46 inches above the top of the rail.The inner box is insulated from the outer box by two pieces of 1/4-inch switchboard.-insulating matting cemented together. To cover the top, two ends, two sides, and the bottom of the box requires 320 square feet of the l/4- inch matting.The walls are well-seasoned tongue-and-groove oak, 1 1/4 inches thick and 2 3/4 inches wide. A 1 1/4-inch air space is maintained by oak strips between the outer wall and the two thicknesses of 1/4-inch rubber matting. The inner box is made of 7/8-inch, well-seasoned, tongue-and groove oak fitted closely against the insulating matting. No nail, rivet, or bolt extends through the rubber insulation.The floor of the outer box is secured to the chassis by two sets of bolts through an intermediate piece of well-seasoned oak. One set of bolts is countersunk from the top of the intermediate piece of oak, and the other set is countersunk from the bottom. The countersunk portions are filled with ""insulate,"" an insulating compound. Adjacent bolts are at least 6 inches apart.The bed of the inner box is divided into six compartments by transverse strips of wood at the bottom and partitions near the roof. Each compartment accommodates three 50-pound cases of explosives. This arrangement prevents cases in adjacent compartments from touching, so that there is no possibility of end thrust of the entire load of explosives. Each inner compartment is 21 inches high, 5g inches long, and 16 1/4 inches wide. Separating strips at the floor are 3 inches wide and 1 1/4 inches thick. The outside dimensions of the 50-pound cases of explosives used are 17 1/2 inches long, 13 1/2 inches wide, and 12 1/2 inches high."

May 1, 1940

By M. S. Celik, H. Du, J. D. Miller, F. Cheng, O. Ozdemir

"In this paper, recent progress with respect to the flotation chemistry of soluble salt minerals is reviewed, and some of the more relevant issues including the hydration states of ions, the interfacial phenomena of salt surfaces and the flotation behavior of selected soluble salts are discussed. Due to the high solubility, the flotation of most soluble salts has to be carried out in their saturated brines. Anecdotal evidence has suggested that the hydration states of the ions have significant influence on the physicochemical properties of the solutions, the surface charge and wetting characteristics of the minerals, the collector adsorption states and, further, the flotation behavior of the soluble salts. In this regard, reviewing past research findings, efforts are made to establish a correlation between the ion hydration states with the flotation behavior of the soluble salts. Further, advances in understanding the significance of colloid adsorption involved in the soluble salt flotation process are addressed, and future research efforts to understand the soluble salt flotation chemistry are suggested.IntroductionSoluble salt minerals are essential raw materials for the production of a variety of commodities, fertilizers, potassium hydroxide, soda ash, magnesium compounds and other chemicals. These soluble mineral resources can be processed using flotation technology and, currently, more than 80% percent of the world’s potash is produced by the selective flotation of KCl crystals (sylvite) from other salt crystals, predominately NaCl (halite) and other more complex salts (Searls, 1990). Despite the successful application of flotation technology in the potash industry, the mechanisms for collector adsorption on soluble salts have not yet been fully understood and, therefore, have been of considerable interest to flotation researchers for many decades."

Jan 1, 2015

By G. Szilvay, P. Kinnunen, J. Salminen, V. Miettinen, O. Salmi, J. Mäkinen

This paper demonstrates experimental studies on bioprocessing of different waste streams. In Part I of this paper three tailings from mining industry were bioleached with mixed acidophilic culture in order to solubilize valuable metals, like copper, nickel, zinc and manganese to leaching liquor. Bioleaching resulted in > 70 %, > 85 %, 100 % and > 70 % leaching yields for Cu, Ni, Zn and Mn, respectively. However, contaminants like arsenic and chromium were not leached efficiently and they will cause challenges in residual solids and sometimes also in metal recovery from leaching liquor. Bioleaching resulted in 99 % leaching yield for copper. Part II demonstrates mine water treatment and also gold recovery from process liquids with biosorption method. The novelty of biosorption was finding that certain fungal species were able to be cultivated to self-immobilized systems, which are easier to operate than traditional suspended biomass methods. Biosorption resulted in more than 90 % removal for all contaminants, but was also seen to be gold selective.

Jan 1, 2014

By G. J. Abbaschian, A. B. Gokhale, M. M. Kunjapur

"A laboratory scale model furnace was constructed for obtaining radially inward oriented columnar grains in disc shaped castings. The furnace consisted of eleven circular, concentric, equispaced resistance heaters on each half of a split graphite mold. Water or air flowing through a copper pipe along the periphery of the disc constituted the heat sink. After filling the mold, the heaters were turned off consecutively in top and bottom pairs from the rim towards the center, causing the temperature gradients to move inward. Equiaxed structure was obtained at the center by turning off the inner coils together when desired. Sn:15%Pb alloy was used to cast integral blade disc castings using the above technique to obtain dual-property discs with a central equiaxed structure and an outer columnar grain structure projecting inwards from the blades to the rim. A numerical technique was used to predict the temperature profile in the disc during solidification, and good correlation was obtained with the experimentally measured temperature profiles. The corresponding heat transfer coefficient values obtained were h = 544 Wm- 2k-1 (0.013 cal/cm2- ° C-sec) for cooling between metal and chill and h' = 71 Wm- 2k-1 (0.0017 cal/cm2- ° C-sec) for the heat input from the hot mold to the liquid metal. BackgroundHigh temperature alloys used in the current generation of gas turbine engines have evolved through two main stages of development: in 1950's, the increase in the efficiency of gas turbines was paced by improvements in alloy design, which led to the development of Ni and Co-based superalloys (1). By mid-1960's, it was realized that improved alloy chemistry alone was inadequate in meeting the increasingly stringent service requirements. The focus of research then shifted from alloy development to process development, and resulted in the introduction of directional solidification (DS) techniques for the production of turbine blades and vanes (1,2).Under typical operating conditions, the blades and vanes are subjected to aerodynamic loading, while the blades are additionally subjected to high centrifugal loading and vibratory stresses. The primary material requirements for blades may be summarized as follows (1,3):•,High creep resistance•,Good high temperature tensile strength (typically in the range of•,275 to 550 MPa at temperatures in excess of 750°C)•,Resistance to both low cycle and high cycle fatigue (LCF and HCF)•,Resistance to erosion, corrosion, and oxidation•,Resistance to thermal fatigue"

Jan 1, 1986

By N. R. MacMillan

INTRODUCTION The Bullmoose Coal Project is part of a major development in northeastern British Columbia which comprises a new rail line, a new townsite, powerline, highway, the upgrading of the Canadian National Railway's main line, a new coal port at Prince Rupert and two new coal mines, the Bullmoose mine and the Quintette mine. The total investment by all parties is estimated to be in excess of $2.6 billion and made up approximately as follows : [Table No. 1 $ Millions - Quintette Coal Limited 950 Teck-Bullmoose Coal Inc. 275 Canadian National Railway Company 800 6 British Columbia Railway Company Port at Prince Rupert 280 Townsite, Roads 6- Power ] The new infrastructure is intended to serve not only the Bullmoose and Quintette coal projects but also eventually a number of other coal properties in northeastern British Columbia. The Bullmoose project is structured on a joint venture basis as follows : [Table No. 2 Teck Corporation 51% Lornex Mining Corporation Ltd. 39% Nissho Iwai Coal Development 1 0% (Canada) Ltd. -- 100% ] The mine has a capacity of 2.3 million tonnes of clean coal per year. In the initial years 1.7 million tonnes will be metallurgical coal and 0.6 million tonnes thermal coal. After the first three years of operations the annual production of metallurgical coal will increase to an average of approximately 2.1 million tonnes and the production of thermal coal will decrease to an average of approximately 0.2 million tonnes. At this level of 2.3 million tonnes annual production, the Bullmoose mine has sufficient reserves for at least 26 years of production. History Brameda Resources Ltd. commenced coal exploration in the Bullmoose-Sukunka area in 1969. Teck obtained an option on the Bullmoose coal licences in 1970 and started surface exploration and diamond drilling in 1971. Teck earned a 50% interest in the property, and thereafter expenses were jointly financed by Teck and Brameda. In 1981 Brameda merged with Teck making Teck the sole owner. The initial phase of the exploration program, which was completed in 1975, included 7,200 meters of diamond drilling in 35 holes. During 1976 and 1977, detailed exploration and test work were carried out on the South Fork and West Fork areas where multiple seams close to surfaces indicated the potential for large tonnages of strippable coal. In those two years, work included road construction, detailed mapping and trenching to outline the coal seam traces at the surface, 6,300 meters of diamond drilling in 80 holes, and 300 meters of underground bulk sampling from seven adits. Washability tests and analysis work were carried out on the drill cores and adit samples, and pilot plant washability studies were undertaken. In 1978 and 1979 Teck engineers prepared open pit mining plans and production schedules and Kaiser Engineering was retained to prepare a layout of the plant preparation facility. A feasibility study prepared by Teck's engineering group in January 1982 was the base document used by the Lenders in assessing the technical and economic viability of the project. Property Location The property lies some 650 kilometers northeast of Vancouver, and 87 kilometers south by road from the village of Chetwynd. The Sukunka property (British Petroleum) adjoins to the north, the Mount Spieker property (Ranger Oil Option) adjoins to the east, and the Quintette property is located to the southeast.

Jan 1, 1985

By B Haase, R Saha

Conditional simulation (CS) has been extensively used in metal industry to assess uncertainty of geo metallurgical variables to build robust distributions around grade tonnages across different time horizons. Coal’s entry to nonlinear stochastic modelling is relatively new and this paper summarises the work done at BHP to enable its practical usage from production time frames to Life of Asset planning. CS in coal using Sequential Gaussian Simulation (SGS) is used to understand resource confidence around specific variables within pre-defined boundaries of spatially continuous domains for each coal seam. The variation between simulations for a given parameter reflects uncertainty. This paper demonstrates the use of CS to profile resource based upon agreed seam/parameter uncertainty thresholds which affect planning, forecasting, extraction and inform identification of key production risks and defining mitigation strategies. The end goal is to de-risk long-term plans by optimising infill data collection and improve stability in short-term planning through increased understanding of confidences locally rather than at global resource definition stages. The paper also briefly discusses the use of automated workflows and systems to minimise the time spent on the process to enable use in decision-making.

Mar 22, 2022