Search Documents

By Warren A. Sheaffer

THE chief uses for copper are as a conductor of electricity and as the chief component in brasses and bronzes. For such uses, the copper must be of very high purity. H the impurities are zinc, iron, lead, arsenic, or antimony, they can be removed to a great extent by fire-refining. H, however, gold, silver, nickel, or cobalt are present, electrolytic refining is necessary. Electrolytic refining must be preceded by fire-refining and hence all impure copper must be fire-refined. The electrolytic refining of copper is most efficiently carried on when the impurities in the anodes are at a minimum. Some of the impurities tend to deposit with the copper at the cathode, while others remain in solution, decreasing the conductivity of the electrolyte and thus increasing the voltage necessary for refining. Since these dissolved impurities must be removed by continuous purifications, the amount of impurity in the anode copper should be reduced by furnace refining to some predetermined limit. Anode furnace operation aims to reduce these impurities to a minimum beyond which the cost of further furnace refining would exceed that of removing the remaining small amounts of impurities from the electrolyte. The anodes should have a fine-grain internal structure because any pieces of metal becoming detached from the anode during the electrolytic refining are inconvenient to remove from the cells and may cause short-circuits. Impurities tend to disrupt such a structure and thus form zones of weakness during corrosion. When the impurities are reduced to a satisfactory mini-mum, the anode, due to having a fine-grain structure, will corrode uniformly over the entire surface area exposed to the electrolyte. Oxides of the impurities may be volatile, in which case they pass off as flue gases, or they may form viscous slags having a lower specific gravity than molten copper, thus permitting their removal by skimming. Some impurities can be oxidized by introducing air into the bath. Due to the large solubility of oxygen in molten copper, oxygen is distributed uniformly throughout the bath and thus comes into intimate contact with all impurities. The oxides which are insoluble in molten. copper are removed either as flue gases or as slag.

Jan 1, 1942

By M. M. Williams

WESTERN CAN ADA'S coal industry has experienced a serious set-back since 1949, following a pattern well known to its counterpart in the United States. The loss in coal markets in Western Canada has been particularly severe as the discovery of large reserves of oil and natural gas and the subsequent construction of re-fineries and pipelines roughly coincided with the dieselization of both main railways. While the coal industry will have to face a further decline in markets of long standing, others with a large growth potential can be se-cured if present marketing methods are changed where needed and if fundamental and applied research programmes are actively pursued. The energy and chemical potential of Western Canada's coals will eventually find their place in the ever-growing needs of industry and electric power producers. Electric power generation would appear to offer the largest and most immediate market for coal. If the coal industry is to serve this market adequately and gain as much of it as possible, coal operators ? must have a good knowledge of certain characteristics -of the electric utility industry and its fuel requirements. This paper is prepared primarily to set out some of these characteristics, but also discusses other probable markets for coal.

Jan 1, 1958

By Nick M. Withers, Suthagarann Visvalingam, Cillian Mc Colgan

The level crossings removal project in Victoria is removing 75 level crossings across Melbourne to improve safety by separating trains from traffic, with other benefits such as reduced congestion, an upgraded road network, connected communities and support of urban regeneration. The level crossing at Station Street in Carrum forms part of the scope being delivered by the Southern Program Alliance (SPA), which is delivering level crossing removal works associated with the Frankston Train Line. At Station Street, a rail viaduct consisting of 19 spans and totalling approximately 545 m in length is under construction to remove the former level crossing. The viaduct consists of two parallel reinforced concrete Utrough girders and steel trough girders, one for each rail line. The foundations of the rail viaduct are founded on groups of Continuous Flight Auger (CFA) piles. The characterisation of geological units encountered at Carrum for the foundation design has been based on insitu testing and interpretation of test results from high strain dynamic pile testing (PDA) and Case Pile Wave Analysis Program (CAPWAP) from the Seaford Road Bridge, located approximately three kilometres South of Carrum, in similar ground conditions. By conducting pile load-deformation analyses based on pile testing significant savings were made for the client compared to the original design which was based on more traditional empirical correlations. This paper discusses the pile design methodology adopted using pile test data for this viaduct foundation. The results of this assessment are also compared to existing empirical correlations, and the limitations are discussed. The performance of the adopted pile design methodology using pile test data at Carrum rail viaduct is also discussed.

Nov 1, 2022

By T. Banerjee, R. deS. Almeida, D. Gudgeon, F. C. F. Batista, L. deÁ. Silva

"Yamana Chapada’s mine is one of the larger copper-gold mines in Brazil. The mine is located in Goiás state, in the central part of Brazil. The mine has estimated Mineral Reserves of 4.1 million ounces of gold and 3.2 billion pounds of copper as of December 31, 2016. While gold and silver are significant, Chapada’s process flowsheet is configured closer to that of copper facilities. This includes a SAG/Ball configuration for grinding followed by flotation. In the case of Chapada, the mineralogy results in higher-than-normal complexity, notably a significant circulating load both in the grinding and flotation circuits. From an operating perspective, the complexities are controllable, but require careful attention to ensure that circulating loads are effectively managed and gold is not lost to tailings. Chapada created an automation roadmap in 2016 designed to increase plant performance (tonnage, recovery and efficiency). Based on strong potential, the project was fast tracked and within 4 months instruments were installed, control algorithms implemented, and training sessions took place to ensure sustainability at site. This paper will follow the Chapada journey from identifying the opportunities through to implementation and testing.IntroductionYamana Chapada mine is a Copper-Gold mine located in Goiás State, Brazil. Although the mine contains large quantities in Mineral Reserve of gold (4.1 million contained oz as of December 31, 2016), Chapada is primarily a copper mine with copper principally found as chalcopyrite. Accordingly, the processing flowsheet at Chapada is comparable to that of other copper mines with a SAG and Ball mill each partnered with a cyclopack, followed by a flotation circuit. While the overall design is conventional, the mineralogy at Chapada results in significant circulating loads both in the grinding and flotation circuits. This does introduce certain complexities for operating strategies and practices, but, importantly, favourable recoveries and elevated processing rates can be maintained, albeit they need to be closely managed. Plant automation helps in this regard."

Jan 1, 2018

By D. W. Butner

This Information Circular , one of a series published by the Bureau of Mines , reports on the methods and costs of mining and concentrating zinclead ore at the Highland Surprise mine in the Pine Creek area of the Coeur d'Alene region of Idaho . The mine is owned and operated by the Highland Surprise Consolidated Mining Co. , which supervises operations of the Nevada Stewart group of claims , which is adjacent on the northwest . These properties are at the extreme eastern end of a zone of fracturing that strikes northwest across the Pine Creek area . In fractures along this zone are the principal Pine Creek mines ; these are the Highland Surprise , Nevada Stewart , Sidney , Denver , V and Idaho , Liberal King , and Northern Light . Country rock at the Highland Surprise is argillite of the Prichard formation (Belt series ) . Fracturing has permitted the movement of mineral- izing agents that have replaced adjacent walls and crushed country rock with sulfides . Ore minerals are sphalerite and galena with accessory pyrite , chalcopyrite , pyrrhotite , and siderite . Three principal ore shoots were found on the Highland Surprise property . The Highland ore shoot was mined from outcrop to the 400 level . The Surprise ore body has been developed to a depth of 1,400 feet on the dip of the vein . The outcrop of the Surprise ore shoot was 150 feet long and 2 to 4 feet thick ; on the 1,150 ( lowest ) level , the ore shoot is 320 feet long and 10 to 17 feet thick , with good zinc content . Surprise ore shoot No. 2 occurs 250 feet west of No. 1 and has been mined from the 500 to the 1,000 level . From 353,000 tons of ore mined between 1910 and 1948 , the property has a recorded production of 256,000 ounces of silver , 7,500 tons of lead , 24,000 tons of zinc , and 412 tons of copper . Both shrinkage and cut and fill stoping methods are used at the Highland Surprise , but shrinkage is unsuitable for mining below the 700 level , because faulting has weakened the walls . Development of the Surprise ore , as well as exploration laterally and along the strike , is prosecuted steadily . A prospect heading is being pushed westward toward Nevada Stewart ground from the 700 level . The mill has a rated capacity of 275 tons per day and operates near capacity . Selective flotation makes zinc concentrate that is shipped to the Anaconda smelter and lead concentrate that is trucked to the Bunker Hill smelter at Kellogg .

Mar 1, 1950

By Staff

The Tetreault mine, operated by the British Metal Corporation (Canada), Limited, holds a unique position in Canadian mining, being the only steady producer of zinc in Canada east of the Rocky mountains. Its importance in Canadian zinc production may be gauged with some accuracy, since, in 1927, it was responsible for over 13 per cent of the zinc output of the Dominion. In addition, it also made valuable contributions to the production of lead, silver, and gold. Location: Situated in the foothills of the Laurentian mountains, 600 feet above sea level, 20 miles from the St. Lawrence river, and 52 miles due west from the city of Quebec, the property is in the township of Montauban, county Portneuf, Province of Quebec, as shown in Figure I. The municipality of Montauban, immediately adjoining the mine, has a permanent population of 700 people and is six miles by road from Notre Dame station on the main line of the C.N. Rys. between Montreal and Chicoutimi-Notre Dame being n6 miles by rail from Montreal. Connection by 19 miles of dirt-and-gravel road with the Provincial highways' system of Quebec Province, the city of Quebec, which is distant 78 miles, can be reached by automobile in less than three hours, while the distance to Montreal by road is 16o miles .

Jan 1, 1928

By A G. Noble

Tunnelling for hydro-electric power projects can be a very challenging component of the overall development. In contrast to urban transportation tunnelling where the logistics for access and supply of power, water and other essentials are readily available, hydropower projects are usually in very remote locations and all necessary plant, equipment, spares and materials need to be brought in and the site must function as a self sufficient unit.For a large scheme the river diversion tunnel(s) are usually on the initial phase critical path in order to meet the non-negotiable deadline of river diversion before the onset of the wet season. A newly formed tunnelling crew, once mobilised to the site for the project, will face the first major learning curve of the project’s systems and logistics during this critical tunnelling activity.Power tunnels convey the water to the turbines in the powerhouse and are usually on the critical path for the main works, especially if the scheme comprises a powerhouse located within an underground cavern. A modern cavern arrangement requires a complex warren of various openings: access adits, ventilation/cable tunnels, shafts, surge tunnels, etc.Hydropower tunnel construction tends to be dominated by tunnel boring machine (TBMs) or drill-and-blast excavation techniques and each has its challenges in very remote locations. TBMs still have long lead times as for any type of project, but additionally require a thorough roads and bridges infrastructure assessment of the country from the port of entry to the site to ensure a problem-free delivery. In some cases the project also requires the establishment of a complete precast concrete segment production facility and the space for creation of laydown areas; there is no ‘just-in-time’ delivery mechanism applicable to typical remote hydropower sites.This paper highlights the technical and risk management considerations in the planning, design and construction of tunnels for hydropower projects. It contrasts the typical factors that govern the design of urban transportation tunnels with those for remote hydropower tunnels. The perspectives of stakeholders are provided including those of international lenders. With examples from large and small scale projects across the globe it provides an insight to all parties and in particular, those tunnellers that are working in the hydropower field for the first time.

Mar 8, 2011

By George Markon

The rapid growth and development of the Soviet coal industry rank the U. S. S. R. with the United States among the leading coal-producing countries. The coal resources of the Soviet Union are among the largest in the world, although coal development has been hindered by the disadvantageous location of the coal deposits with respect to the major consuming centers. Although coal production in the U. S. S. R. reached a record high, the total energy output of mineral fuels in 1957 was still far below that of the United States because a significant part of Soviet coal output was lignites or lower rank coals. Although the Soviet coal industry soon may exceed that of the United States in tons produced, the energy equivalent of Soviet output will be considerably less because of the inclusion of a high percentage of lower rank coals. Energy sources in the United States also involve large quantities of oil and natural gas, whereas coal supplies most primary energy in the Soviet Union.

Jan 1, 1959

By R H DAVIES

Peak Gold Mine is a new gold and base metal mining project being developed by Enterprise Metals (a 100 per cent subsidiary of CRA) at Cobar in the centre of New South Wales. The Cobar district has a long history of copper and gold mining operations stretching back to the 1870s. Extensive gold and base metal mineralisation was discovered at the Peak in 1981 below a series of gold mines which had been active around the turn of the century. Evaluation of the deposit through the 1980s led to CRA's decision to develop the project for production at a capacity of 450 000 tonnes per annum in late 1992. The project has been developed with a green fields approach despite the long history of mining in the local area. This approach has lead to several innovative ideas being trialed at the site which are expected to result in the operation being a low cost producer of gold and base metals.

Jan 1, 1992

By D Kay, M Lovitt

Mass Blasts are generally required at the completion of longhole stoping cycles to maximise the recovery of ore from a specific orebody. During the course of mining, the practice is to leave pillars of ore to support the opening left by extracted ore and to mitigate stresses from working areas of the stope. These pillars usually contain ore that has been included in the resource evaluation and is highly valuable to the mining operation. Due to their stressed nature, the removal of pillars by conventional blasting techniques, through small blasts, can result in pillars being reduced beyond their critical size and ultimately failing, rendering the ore unrecoverable. The AurionGold Kanowna Belle Gold Mine operates a Mine to Mill philosophy. This philosopy requires the fine tuning of blasting to provide the best possibe ore feed at the highest grade for mill productivity. This means that ore to the mill must be well fragmented from blasting that provides high extraction rates from draw points, with minimal dilution from overbreak or fall off, and sized to maximise SAG mill throughput. The AT04 Mass Blast contained significant ore reserves which were required to meet gold production targets. KBGB needed the AT04 Mass Blast to perform as well as if not better than conventional stope blasts to maintain mill production. This paper describes the circumstances, planning philosophy, techniques, including the use of Electronic Initiation Systems and Bulk Emulsion Explosives, and results that provided a highly successful outcome.

Jan 1, 2002

By AIME AIME

CERTAINLY in point of attendance, and doubtless in several other ways as well, the 147th meeting of the A.I.M.E. was the best ever held. In times of depression, mining engineers and metallurgists have plenty of time to come to the Annual Meeting but money is scarce; at the height of industrial activity they have plenty of money but no time. "The current period of transition seemed to provide ideal conditions for' both the preparation of papers and attendance at their presentation. The weather made even the Californians present envious though the weather man gets no credit, for rain and snow was what he willed. Among the elevator men, the miners have the reputation of being the toughest crowd to handle, though the best natured, withal, of all the engineering groups that meet in the Engineering Societies Building. This year Your inquiring reporter was told, "it was the damnedest meeting I ever saw; they

Jan 1, 1937

By Leon E. Laforest

An early commitment by Kidd Creek Mines Ltd. (formerly Texasgulf Canada) to follow a stringent environmental control programme from the initial stages of design and development of its metallurgical facilities in Timmins, Ontario, has resulted in the on-going attainment of extremely low levels of industrial waste emissions. This paper outlines the monitoring programme initiated and maintained by the company's environmental control section. Comparative results of environmental sampling for the periods before and after the copper smelter start-up are highlighted.

Jan 1, 1983

By Cathy Aimone-Martin, Frank Achuff

The New Mexico Department of Transportation (NMDOT) and the Federal Highway Administration (FHWA) have let a contract to Sierra Blanca Constructors for a design / build contract along 38 miles US 70 in Lincoln County, New Mexico. The project will improve safety of travel along the corridor and facilitate the adopted economic development goals of the state. Proposed improvements include widening the existing highway from two lanes to four lanes, providing left turn lane options at selected locations, improving access for businesses and residences, aesthetically enhancing retaining walls, improving storm drainage and replacing the existing pavement with a 30 year mechanistic imperialistic perpetual pavement design. The US 70 Hondo Valley highway project is situated in a narrow valley with steep limestone walls, passes along a Scenic Byway and numerous historic ranching communities with structures that date back three centuries. The scope of work included requirements to monitor and mitigate blasting, noise, and vibrations. The contract was very presumptive with regard to blasting design and procedures. These included visual impact mitigation to treat and stabilize slope cuts, the Migratory Bird Treaty Act protecting roosting and nesting birds from airblast, and the protection of historic and cultural features such as acequias, wells, and structures. Public involvement affecting the rock blasting design has come from citizen task forces and committees concerned with highwall aesthetics and preserving the scenic byway and cultural resources. Constraints placed on the blasting program from agencies and the communities are often at odds. For instance, blasting must produce stable yet natural-looking walls to preserve aesthetics. Restrictions have been placed on pre-splitting and smooth-wall blasting yet safe slope are of the highest priority. This paper presents details of the design/build process undertaken by the contractors to conduct blast rock in an environmentally sensitive region. Blast designs consistent with good construction practices and used to comply with the many federal and state highway stipulations are described.

Jan 1, 2004

By Clarence P. Linville

(Pittsburg Meeting, March, 1910.) IT is recognized that, in all metallurgical operations, the greatest possible uniformity in all conditions is essential to the best results. It is the constant aim of metallurgists to secure this uniformity, and their success in this respect has been in many cases the cause of great advances in the metallurgical processes themselves. Of all such processes, the production of pig-iron in the modern blast-furnace is perhaps the most complex and the most difficult of control. Notwithstanding the great progress of recent years, there is still great difficulty in obtaining anything like uniform conditions and results in the manufacture of pig-iron. The reason is not far to seek. The ores vary in composition and physical properties, often carrying a varying amount of gangue material, unevenly distributed The coke may vary in composition, cell-structure, moisture, hardness, and other properties. The blast, the weight of which far exceeds that of any other constituent, varies in its moisture-content and consequently in its chemical composition ; and its temperature, by reason of the method of heating, is not uniform, but, besides varying from time to time with atmospheric and other outside conditions, has a maximum and minimum for every changing of stoves. Now, with regard to these variations, the modern demand for uniformity has been greatly aided. Chemical analysis has made it possible to select ores so that the composition of the charge can be kept fairly constant; coal may be obtained from a given field, and coked in the same kind of ovens under conditions which . make the fuel practically uniform ; the Gayley

Mar 1, 1910

By Joseph T. Singewald

The possible value of the red hematite iron ore of the southern Appalachian States, if some practicable method of concentrating it could be devised, has long been recognized. The ore is very low grade, and although in enormous quantities, particularly in the States of Alabama, Tennessee, and Georgia, is only at a few points rich enough to work, and even the best of it ranks among the lowest grade iron ores being mined in the United States. A cheap method of beneficiating this ore would make enormous quantities available and vastly increase the iron-ore resources of the country. However, this low-grade ore in effect constitutes a potential iron reserve, and as long as ample quantities of ore can be obtained elsewhere the question of its utilization does not demand immediate notice. Where these ores are in part of workable grade, however, a problem of more immediate importance arises which, from considerations of economy and prevention of waste in their mining, ought to be solved or, at least, attacked as quickly as possible. Where these ores are being worked they are usually intimately associated with lower-grade material that in mining is left behind. The difficulty and expense of going into ground broken by old workings makes the recovery of this lower-grade ore practically impossible and it is lost forever. Success in concentrating the red ores, therefore, would save material that is now being irretrievably lost. The successful large-scale concentration of law-grade ore in the last few years on the Lake Superior iron ranges should encourage the attack of similar problems in the Birmingham district.

Jan 1, 1917

By Micah Nehring, MEHMET KIZIL, Farzad Sotoudeh, Amin Mousavi, PETER KNIGHTS

Production scheduling in underground mines is one of the most important and complex processes in maximising the economic value of an operation over the life of the mine. Due to increasing energy, transportation, processing and smelting costs and reducing water availability, the extraction of ore deposits through underground operations has become more expensive and challenging. A potential productive and efficient solution to mitigate these issues is to integrate pre-concentration systems into the existing mining system to increase ore grades through a preliminary process of rejecting some waste before sending the ore to the energy intensive mineral processing plant. Further benefit of such systems includes the utilisation of the waste and low-grade material in backfilling of open stopes to reduce the transportation costs and surface environmental impact such as reduction of CO2 emissions and waste transportation. The objective of this paper is to present a new mathematical model to optimise the production schedule of underground metalliferous mining operations in the presence of a pre-concentration system. The proposed model optimises the production schedule and sequencing of stopes within a sublevel stoping operation. The results of this study illustrate the potential economic benefits of using a pre-concentration system prior to a mineral processing operation as a result of increased net present value.

Nov 16, 2023

By R Redden

"The Didipio Gold-Copper project in the Philippines has been a well-defined reasonably high gold grade porphyry for almost two decades. OceanaGold are now bringing the project into production in late 2012 and have recently reoptimised the project with the goal of combining the inherent high grades with higher through-put than previously proposed that will see strong initial metal production. The project was discovered and well defined by 1995, but has seen some obstacles to development, namely sovereign risk, capital cost and project funding. The project strengths over this time that have kept the flames alive are: strong grades large orebody with low stripping ratios a simple beneficiation process and a clean high-grade concentrate strong support from the Philippines government.The initial study in 1998 used Gold and Copper price assumptions of $325/oz and $0.95 lb respectively. Today reserves are based on $950 and $2.85. So, being a porphyry with a large reducing grade halo, the deposit now lends itself to extraction on a much larger scale than before, without any significant capital expenditure as a larger open pit now dominates the project.Didipio is a game changer for OceanaGold, so it has been important to learn from history and to capitalise on a strong initial metal production profile. The project sits in a reasonably remote mountainous area of Luzon which sees annual typhoons and numerous short duration high intensity rainfall events and two rivers flowing through the project area, so it has not been without some innovative technical solutions.CITATION:Redden, R, 2012. Didipio - Learning the lessons, adapting and getting ready for production, in Proceedings Project Evaluation 2012, pp 67-76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012

By G. De Gregoriis, G. E. da Mota, H. P. Dias, J. E. M. Blasques

In recent years, like many other smelters around the world, Albras has been increasing line current. The necessary adjustments to the work practices and process variables need to be made on all potlines, which in this case means on 960 cells at the same time. It was a challenging task to adjust the process parameters to the new amperage. In July 2003 potlines 2, 3 and 4 were running at 1 73 kA and the goal at that time was to reach 180 kA. Preliminary trials with 180 kA were performed on a group of 10 boosted cells on potline 3 in order to investigate possible operational problems. It was decided to increase the amperage in three steps accompanied by continual evaluation of the state of the process. In July 2004 the target of 180 kA was achieved with good operational results. This paper presents the overall results, the parameter adjustments made during the amperage increase in the booster group and how the increase was implemented on the other potlines.

Jan 1, 2006

By Michael A. Anuta

This report describes the potential for utilization of satellite observations for remote sensing of mine waste disposal areas. Four study sites consisting of metal and nonmetal mining areas in different climatic and physiographic regions of contigous United States were used in this investigation. The mine waste disposal sites consisted of mining of phosphates in Florida, copper in Arizona, silver in Idaho, and coal in West Virginia. Landsat satellite multispectral scanner observations were used together with aerial photographs, ground surveys, U.S. Geological Survey maps, and other ancillary information. Landsat digital data were categorized using automated supervised classification algorithms and an image analysis system. Detailed description of automated classification techniques employed and the accuracy attained is provided together with the results of manual interpretations. The inventory of areas distrubed for phosphate mining and a change detection investigation for-Polk County Florida were also undertaken during this study.

Jan 1, 1982

By Todd W. Armstrong, Michael D. Reader

"INTRODUCTIONThe Playa Vista Development is the largest urban infill development in the history of the United States. Overall, it encompasses about 1100 acres in the City of Los Angeles and is situated north of Los Angeles International Airport near the Pacific Ocean. The development taking place on the project consists primarily of high-density residential condominiums with 1 to 2 levels of subterranean parking . The geotechnical conditions are typified by high groundwater, soft clays, and liquefaction, in addition to environmental issues such as methane.Due to a combination of the geotechnical factors and noise restrictions, both driven and drilled piles were not feasible once the initial phase of the project was occupied. As a result, the project developer undertook a testing program that consisted of the installation and load testing of 9 piles in order to obtain City of Los Angeles acceptance of a pile installation system that met the site constraints. The testing program was divided between two separate contractors operating on sites set on opposite sides on the street (Figure 1 ). Contractors working in Test Areas A & B employed the ""dry dip"" and ""wet dip"" methods of auger pressure grouted displacement (APGD) pile installation, respectively.This paper summarizes the extraordinary program undertaken to install, document, test, and examine auger pressure grouted displacement piles at this site. The program ultimately resulted in City acceptance of auger pressure grouted displacement piles, a historically difficult challenge given the City's resistance of acceptance of ""new"" technologies.A summary of elements included in the test program are: (1) quality control; (2) load testing; (3) long-term testing; (4) non-destructive testing; and (5) pile exhumation."

Jan 1, 2005