Search Documents

By Xinli Wang, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng, Byoung-Gon Kim

"The microwave reflection loss (RL) of ferric oxide is studied in the temperature range from 297 to approximately 1400 Kat frequencies of 915 and 2450 MHz. It is shown that the maximum microwave absorption with RL of -38.46 and -35.97 dB can be obtained for ferric oxide having thicknesses of 0.03 and 0.01 m at 915 and 2450 MHz, respectively. The maximum absorption peak with RL below -10 dB is in a 250 K temperature range from 723 to 973 Kat 915 MHz, which shifts to the range between 823 and 1073 K at 2450 MHz. This migration is in good agreement with the variation of the dielectric loss tangent of ferric oxide.IntroductionMicrowave irradiation has distinguishing characteristics such as volumetric and selective heating compared with conventional methods, leading to extremely broad applications in materials heating and processing [1-5].The efficiency of microwave heating was found to be dependent on various factors, such as microwave power [6], frequency [7,8], radiation time [8], applicator geometry [8], sample microwave absorption properties and position as well as dimension [9-11 ], etc. Among these parameters, sample dimension plays an important role but is usually neglected by researchers in microwave processing of materials. In fact, although numerous studies have been directed toward the utilization of microwave energy to assist materials heating and processing, few reports were released on the effect of sample dimension [12,13].This is because all aforementioned factors influencing microwave heating generally exert interactive effects to each other during the heating process, making clarification of the effect of sample dimension difficult. Therefore, it is necessary to propose a parameter or concept for quantifying the effect of absorber dimension on microwave heating, increasing heating efficiency."

Jan 1, 2013

By Yotamu Hara, Animesh Jha

"High Curie temperature and large magnetic anisotropy make cobalt an important magnetic material for power engineering applications of magnets operating above ambient. It is also an essential constituent of modem lithium - cobalt oxide batteries, without which modem electronic gadgets will be functionless. Both these applications of cobalt save energy and reduce C02 emission. Ironically, however the production of cobalt from copper and nickel smelting in the world remains one of the least energy efficient process. The paper analyzes the energy balance, material and process chemistry of overall cobalt recovery and the waste generated, which entail the process limitations. We discuss a novel approach for the reduction of sulphide minerals with CaS04, permitting better separation of metals from slag and generating higher concentrations of S02. Such an approach may seem to be an alternative energy efficient option for processing and further purification of cobalt in metallic form. The results are discussed in the context of process thermodynamics and reaction kinetics for Coalloy production.IntroductionCopper sulphides bearing minerals are predominantly associated with iron and cobalt sulphides minerals. Carrollite (CuC02S4) is a mineral that has both copper and cobalt sulphides [1,2], which may also contain FeS, by substituting either Cu2+ or Co2+ ions in mineral lattice. On smelting copper - cobalt - iron sulphide concentrates, some parts of the cobalt often partition to matte at preferentially low oxygen potential by forming eventually an alloy phase with copper, however a significant fraction is often lost into an oxide slag rich in iron and silica. The slag heaps accumulated in the Copperbelt region in Zambia from last 60 years of mineral processing and metal extraction is reported to be 0.3 to 2.6 wt% of cobalt element, which is high [3]. Cobalt is also available in smaller concentrations in the copper smelting and converter slag, as reported in the investigations on the recycling of such slag materials using leaching with ammonium salt [4], iron chloride [5], and sulphuric acid [6], and solvent extraction [7].The recovery of cobalt from slag, irrespective of the techniques researched so far, does not seem energy efficient because the molten slag at 1300°C is quenched by losing thermal and chemical energy. The quenched slag is again reheated to above room temperature for leaching and above liquidus for carbothermic reduction of residual cobalt oxide. For example, in Mintek DC arc smelting [3], 80% of cobalt and 95% nickel are recovered by expending 600 kW per tonne. Assuming that the mineral carrollite is the starting phase, the univariant calculations for the Co-Ca-Si-S-0, Fe-Ca-Si-S-0, and Co-C-Si-S-0 systems are shown in Figure la, lb, and le, respectively at 1573 K."

Jan 1, 2012

By S. Banisi, E. Arghavani, M. Pourkani, M. J. Rajabi, Gh. A. Mohamadian, H. Bidshahri, Gh. A. Parsapour

The Sarcheshmeh copper complex flotation circuit of plant No.1 consists of two identical north and south sections where each includes four rougher (each bank consists of 14 cells), two cleaners (each bank consists of 8 cells), two recleaners (each bank consists of 2 cells), and two scavenger banks (each bank consists of 10 cells). The reduction of feed grade along with a change in the mineralogical composition is the main reason of current lower concentrate grade (24%) compared with the design concentrate grade (32%). Because of a lower feed grade, the amount of rougher concentrate has decreased which in turn has significantly reduced the feed rate to the cleaner, recleaner, and scavenger banks. This has increased the mean residence time of the material in the cleaner section resulting in a lower final concentrate grade. A laboratory study showed that the final concentrate grade can be increased by 2-4% if one cleaner stage is added to the flotation circuit. In this research, based on the laboratory results, one cleaning stage was added to the current flotation circuit. In order to make this modification instrumentally possible in the plant, the final concentrate was gravity transported to the Mo-Cu thickeners. This released 2 pumps and associated tanks which made addition of one cleaning stage practicable. Finally, a part of the cleaner and scavenger cells were used as the third cleaning stage. This decreased the residence time in the cleaner and scavenger banks. After implementation of one cleaning stage in the south section of the plant, the performance of the circuit compared with the identical north section. It was found that at the same recovery, the concentrate grade of the south section increased by 2.5%. The promising results led to the implementation of adding one cleaning stage in all sections of the flotation circuit.

Jan 1, 2018

By C. E. Jordan

The Tuscaloosa Metallurgy Research Center of the Bureau of Mines, U.S. Department of the Interior, is investigating the recovery of phosphate from beneficiation slime, as part of the Bureau's efforts to conserve mineral resources through increased use of wastes. Phosphate equivalent to about two-fifths of U.S. production is discarded annually in the wastes. Exploratory flotation tests on the plus 5-um fraction of a slime sample showed promise for a classification-flotation technique. Onsite classification tests at six phosphate washing plants were conducted with a two-stage hydro cyclone system designed to recover the plus 5-um material. The cyclone underflows contained 8.3 to 19.1 percent P2O5, and the recovery of the plus 5-um PZOS values ranged from 81 to 95 percent. The percent P2O5 recovery from the total slimes ranged from 38 to 47 percent. Batch-flotation studies are currently being conducted.

Jan 1, 1978

By W. R. Cowan

The Caledon Outwash is a large deposit of glaciofluvial gravel and sand located 55 km north west of down town Toronto. For the most part it was laid down in a meltwater channel fronting the Paris Moraine about 14,000 years ago. Applying the braided bar model of Eynon and Walker (1974) the principal facies present are imbricated coarse gravels (bar corefacies); crudely stratified, imbricated bar top sandy gravels; and trough crossbedded side channel sands and gravelly sands. Of lesser importance are crossbedded bar front gravels, shallow braided stream facies gravels, and stoss side facies sands and pebbly sands (rare). Lithologically these deposits are characterized by FIGURE I. Geological relationships of Caledon Outwash. Industrial Minerals in Canada up to 95% Ordovician limestone and siltstone in the gravel fraction. A siltstone content of up to 34% requires that beneficiation be carried out for the production of better quality aggregates. Resources remaining are estimated to exceed 500 million tonnes in 3000 ha of the most suitable part of the deposit. Present production is about 4.5 million tonnes per year, shared by several producers.

Jan 1, 1984

By Quenton Johnson, W. A. Gough, David Carr

"This paper describes the application of the BrainWave Model Predictive Controller (MPC) and Advanced Control Expert (ACE) Advanced Supervisory Control System on the SAG Mill, Ball Mill, and Rougher Flotation cells for a new gold processing line at the Oceana Gold - Haile Gold mine in Kershaw, South Carolina. For this project, ANDRITZ supplied the control system design and programming, operator-training simulator and advanced control. The advanced control was tested against the IDEAS™ dynamic simulator, and commissioned during the startup of the processing plant to help achieve target production as quickly as possible. Operators were able to run the equipment in a consistent and optimized manner from an early stage of the plant operation, increasing efficiency and profitability. MPC is able to reduce process variability beyond the best performance that can be obtained with conventional Proportional Integral Derivative (PID) control methods. MPC is able to optimize the control of processes that exhibit an integrating type response in combination with transport delays or variable interaction, which are characteristic of many gold processes including SAG mill weight control and Flotation cell froth level control. The experience and benefits of applying MPC during the startup of a new gold processing plant are presented in this paper.INTRODUCTION Mineral processing operations present many challenges for automatic process control due to variations in unmeasured ore properties, material transport delays, and non-linear response characteristics. Advanced process control technologies such as expert systems and multi-variable model predictive controllers are often used to improve the control of these processes to increase productivity and recovery efficiency. Typically these systems are applied after the mine has been in operation for a period of time. For this project, a complete dynamic process simulator was developed using the IDEAS platform for the purpose of training operators before the plant was constructed. Operators were able to become familiar with the process and the control system in order to become proficient in the use of the controls before the plant was ready to start. They were able to practice abnormal condition management including startup and shutdown of the process using the simulator and develop complete Standard Operating Procedures (SOPs) for these situations. The simulator was also used to test the control system functionality and operator Human Machine Interface (HMI) configuration to reduce errors and improve the performance of the control system during plant start-up."

Jan 1, 2017

By L. C. Brichta

The Melrose zinc-lead. deposit is in an area of structural disturbance of sedimentary rocks in the Melrose mining district in Cherokee County, Kans., 25 miles west of Joplin, Mo., adjacent to the northwest limits of the Tri-State district. Mining and milling in the Melrose district has been sporadic and. very limited, largely due to the high cost of exploration through great thicknesses of barren rock, 350 to 440 feet overlying the ore deposits. No mining has ever been done on the Melrose zinc-lead tract, but it has been drilled extensively. The drill-hole logy indicate extensive structural deformation, silicification, and zinc-lead deposits in the Boone limestone-chert formations of the Mississippian series, which is overlain by thick-bedded Pennsylvanian shale and sandstone. Analyses of samples from Bureau of Mines drilling indicate the ore minerals are sphalerite and galena with no evident oxidation. During the period from November 2, 1949, to March 13, 1950, the Bureau of Mines investigated the deposit by churn drilling and sampling 23 holes aggregating 10,405 feet of bore. Factual data on the investigation and logs of holes drilled by private parties and the Bureau of Mines are presented in this report.

Jan 1, 1951

By Hideki Yarnarnoto

The simultaneous removal for NH4+ and PO43- in aqueous solution was carried out by using Ca type zeolite synthesized from coal fly ash. The effect of pH on the cation exchange capacity and adsorption properties of the obtained zeolite, the simultaneous removal of NH4' and ~04'. in various solutions and the mechanism of simultaneous removal were investigated respectivel? ,The Ca type zeolite used in this study can simultaneously remove NH4+ and PO43- In aqueous solution without releasing counter ion, and this method gives great advantage over the other ordinary removal methods.

Jan 1, 2002

By Rui Xiang Yang, Cong Li, Jia Zeng, Rong Liang Zhang, Wei Zhang, Chao Fan Tang

This research took the roasted products obtained by leaching copper (Cu) refining slag using waste acids and roasting leaching residues with calcium oxide (CaO) as raw materials and used oxidative leaching to extract Cu from roasted products using waste acids. Influences of the leaching temperature, liquid–solid ratio, and sulfuric acid ( H2SO4) concentration in waste acids on the leaching rate of Cu in the oxidative leaching process of roasted products using waste acids were investigated. The unreacted-core shrinking model of heterogeneous reactions was adopted to reveal the leaching kinetics of Cu in the oxidative leaching process of roasted products using waste acids. Results show that the leaching rate of Cu reaches 91.68% when the leaching temperature, liquid–solid ratio, H2SO4 concentration in waste acids, and injected airflow are 80 ℃, 8:1, 1.5 mol/L, and 200 mL/min, respectively. If the leaching temperature is below 80 ℃, the leaching process of Cu is controlled by the solid-film diffusion, and the apparent activation energy Ea is 11.0835 kJ/mol; at a leaching temperature above 80 ℃, the leaching process of Cu is governed by the interfacial chemical reaction, with an apparent activation energy Ea of 42.3183 kJ/mol. The liquid–solid ratio can positively influence the reaction rate constant. The apparent order of the leaching reaction of Cu is 0.632.

Jan 11, 2023

By Wenkai Wan, Charlie C. Li

Strain burst can occur in underground hard rock excavation when the in-situ stresses are high enough. The prerequisite for rock burst is that the total energy released from the rock mass is higher than the energy needed for rock fracture. The total released energy is contributed by both the burst rock and the surrounding rock. The part of the energy from the burst rock is constant per unit volume of the rock, but the part from the surrounding rock is associated with the burst volume. A greater amount of energy will be released from the surrounding rock in the case of a larger volume of burst rock. The postulation for the energy conversion in strain burst is verified through a FLAC3D model in the paper. It is assumed that the strain burst occurs in a circular tunnel that is located in the hydrostatically loaded rock mass in the model. Six pairs of notches with different depths are created in the opposite walls of the tunnel to simulate the bursts. The energies released from the notch rocks and from the surrounding rock are calculated during the burst. The simulation results show that the percentage of the energy released from the surrounding rock in the total released energy increases with the notch depth. The numerical modelling confirms the postulation that the surrounding rock contributes more energy than the burst rock itself in large-scale strain bursts

Apr 26, 2022

By Grieve BL

For a blast to be successful both heave and fragmentation must be satisfactory. Amongst the major factors influencing blasting are rock properties. This paper considers the effect of rock density on fragmentation and heave and how better results can be achieved in dense ore. Patterns which increase the heave and give better fragmentation are examined and the application of theory to the blasting of the Dales Gorge Haematite, density 4.2 - 4.5 t.m.,3 is then discussed. The drilling of staggered patterns instead of square patterns and a shallower 'V' initiation system has given better heave and fragmentation. This practice has re- duced backbreak and improved toe conditions; these factors have resulted in increased load ing rates. There has been an increase in the lump/fine ratio which is consistent with the theory although other factors such as ground conditions could have contributed.

Jan 1, 1978

By E. Emelyanenko, P. Solozhenkin, J. Yagudina, O. Ibragimova

To recover tetrahedrite-tennantite series minerals from porphyry copper-pyrite ores by the froth flotation method, further research on thiol collectors is launched to promote the utilization efficiency of copper ores. In the present paper the adsorption mechanism of the collectors on tennantite surface has been investigated by computational modeling and FTIR-spectroscopic analysis, which have revealed that the decrease in prognosis of collector activity evaluation (PCAE) for tennantite is in the following order: BX (-0.34318), AEROPHINE 3418A (- 0.61756), AERO 5100 (-14.18857). The lower PCAE the stronger the ability of the collector to interact with the mineral surface of tennantite and form the stable complex. More kinetic reliable conditions to form suitable adsorption layer and rupture of the liquid interlayer with AERO 5100 have been observed by FTIR spectra due to decrease of the intensity and stretching and bending vibrations of water (less than 20 and 65%, respectively). In order to verify the feasibility of AERO 5100 as a collector the industrial flotation tests have been conducted. Flotation performance has improved significantly with the stadially grinding and preflotation of tennantite in intercycle copper flotation that allows to avoid desliming of the fragile mineral and minimize loss of Cu and As in tailings. The recovery of copper in copper concentrate increases by 3.9% with the grade maintained.

Jan 1, 2018

By J. S. Carman

As with the slogans of Madison Avenue, catch words or phrases frequently become topical. Much is heard these days of the confrontation between governments of developing countries and international mining capital. In actual fact, sadly there are too few cases of anything as positive as confrontation because such an action at least signifies a dialogue which may begin badly but end up fruitfully. Instead we have in general a climate of indifference and fear with the mining companies of note marking off most of the developing world as being unsafe for investment. There is an unreal air to this damaging impasse. The common sense and objectivity which are prerequisites of positive action are lost in a swirling cloud of mythology, embraced largely by governments. Let us examine some of the dangerous misconceptions.

Jan 1, 1977

RUSSIA was the United States Number One source of manganese ore in 1948 when 34 pet of imports were received from that source, stated Norwood B. Melcher, assistant chief, ferrous metals and alloys branch, Bureau of Mines. In 1949, this country received only 20 pet of 1948 shipments from Russia, and only token amounts are now being received. Aggressive programming by industry and government resulted in prompt increases in shipments from major, producing sources; India, Gold Coast, and the Union of South Africa all increased exports to fill the vacuum left by Russia and provided an excess adequate to increase total imports approximately 290,000 short tons in 1949. Again in 1950, and with, even less ore from Russia, imports increased another 290,000 short tons. Since the shift from Russia as a source of manganese, the United States has received in total about 85 pet of its imports from India, Union of South Africa, Gold Coast, and Brazil in that order of importance. Producers of both home consumed and merchant ferromanganese have been able to adjust downward the manganese content of the home-consumed product and so obtain partial relief. Millions of tons of steel were produced in 1951 with a relatively low grade ferromanganese. This adjustment has been made without decreasing the quality of the steel, although with some increase in cost through introduction of new problems, including increased hand- . ding of material and additional removal of carbon. Forced into a pattern of price and grade structure such as exists today, the producer of ferromanganese must adopt one of three possible courses as a short-range program: 1-He may continue to deplete his stocks by producing standard (78 pet) ferromanganese and hope that the future will bring some form of relief; 2-he may attempt to produce 78 pet ferromanganese by paying higher prices for premium ores; or 3-he may drop the grade of ferromanganese and stretch stocks and future supplies of ore as far as possible. The present rundown condition of Indian railroads is attributed to the fact that the service has had no opportunity to recuperate since the beginning of World War II, while the demand for the movement of commodities has probably increased. The Union of South Africa has expanded its exports to the United States greatly since 1948, but, the showing of that country in 1951 was disappointing. Efforts have been made for some time by firms in the United States, at the urging of the manganese miners in the Union, to prevail on the railroad authority to grant and make available larger allocations of cars for manganese ore movement. As a whole, such efforts have been unsuccessful. Although the allocation of rail shipping has been the obvious factor in the decreased movement of ore, many other less determinate factors appear to be involved. Brazil, long an important supplier of manganese to the United States, has important manganese deposits in three areas, all of which are significant to this country. The Gold Coast is an important source of supply. Its metallurgical ore is particularly of significance because of its unusually high grade which permits considerable latitude in blending with the lower grade materials of South Africa and India. The Belgian Congo should have an output of 100,000 tons or more annually beginning this year. R. S. Dean presented two papers. One with K. M. Leute on hydrometallurgical methods for recovery of manganese from domestic ores and one as sole author on the so-called carbamate or Dean process. The two papers tied into each other. In the first mentioned he reviewed the various processes applicable to oxidized, and nonoxidized and reduced ores. The advantages of each .were pointed out. So far the only process tried on a substantial scale on oxidized ores was the SO2 process used at Las Vegas, Nev., on Three Kids ore during World War II. Many problems were encountered. Some of them were whipped while some of those remaining perhaps would have been whipped had time permitted. Since then work has been done elsewhere to avoid the formation of the troublesome thionates encountered at the Three Kids plant. Dean discussed the thionate and NO, processes as applied to oxidized ores. The only commercially used process on reduced ores is that of making electrolytic manganese. Among others that have been considered are the nitric acid process, the Bradley-Fitch ammonium sulphate process, and Dean's ammonium carbamate process. Dean's thesis was that extremely large tonnages of so-called low grade manganese ores are available, and that these should not be depleted in attempting to simulate a foreign metallurgical grade ore. He pointed out that the grade of the domestic manganese ores would be considered high if the same grade were found in copper ores. The selling price of electrolytic manganese and electrolytic copper are roughly the same. In addition to electrolytic manganese, he believes that domestic ores should be used to make exceptionally high grade products. These might be battery grade oxide or substantially pure oxide sinter, which might be used for high manganese alloys or for upgrading metallurgical grade manganese to produce a high manganese ferroalloy. The carbamate process is based on the fact that manganous oxide is readily soluble in concentrated ammonia solutions containing ammonium salts. In solutions of sufficiently high concentration the manganese exists as an anion. Lixiviants of ammonia and ammonium carbonate permit extraction of the manganese from reduced ores and the manganese can be recovered as carbonate by heating or by driving off ammonia. R. V. Lundquist presented a paper on upgrading high-silica ores or concentrates with sodium hydroxide to extract silica and to yield a product with a more favorable manganese: silica ratio. The NaOH is, regenerated in part by CaO.

Jan 1, 1952

By W. F. Stowasser

Robert E. Hagen (Oliver Iron Mining Div., U. S. Steel Corp.)—Mr. Stowasser and his associates are to be congratulated on their achievements in developing the design of a pilot agglomerating plant, based on information obtained from experiments made in a laboratory sinter pot, and subsequently constructing and successfully operating this plant. In his Transactions article, May 1955 (vol. 201) Mr. Stowasser stated that the output of his heat treating strand was about 2 Lt per sq ft of grate area per day and that the fuel consumption was 0.7 to 0.8 million Btu per Lt of product. If it is assumed that the burning zone extends from the back of the ignition furnace to the beginning of the recuperation windbox, only about 1/3 of the grate area over the windboxes is utilized for burning pellets, and the actual rate at which partially dried pellets are burned is about 6 Lt per sq ft of grate area per day. It may be interesting to compare the above operating data with that obtained at the Extaca plant, where taconite concentrate is treated on a conventional sin- tering machine using limestone or hydrated lime additives with no recuperation of heat. The entire windbox area is used for burning, and a production rate of 2.5 Lt per sq ft of windbox area per day has been attained at a fuel consumption of 1.8 to 2.0 million Btu per Lt of product, the latter being considerably in excess of that reported by Mr. Stowasser, partly because a circulating load of returns amounting to 28 to 30 pct of the machine feed is used and because no attempt is made to recuperate heat from the waste gases. With the high capital and labor costs prevailing today, it seems that future development of the downdraft grate pelletizing process should be directed toward taking advantage of the high burning rate of predried pellets and increasing capacity, perhaps at the expense of fuel economy, by decreasing the proportion of grate area utilized by ancillary functions. For example, eliminating the cooling zone and using this area for burning would increase the proportion of grate area available for burning from 33 to 50 pct of the total windbox area, and a proportionate increase in capacity would result.

Jan 1, 1956

Gas-liquid contacting in the packed bed is a common operation in metallurgical reactors. Research has shown that, unlike wetting flow, non-wetting liquid flows in the form of discrete droplets or rivulets. Thus, modeling of the liquid phase as a continuum is in contradiction to the observations. Also, for the non-wetting case, continuum models have failed to describe liquid flow path when the liquid source is a point source. The aim of the current work is to put forward a combined Lagrangian-Eulerian approach to model the liquid and gas flow in the packed bed. Liquid is assumed discrete and modeled using a force balance approach. Gas is assumed to be interpenetrating continua and modeled using k-emodel for turbulent flow. Structured packing is assumed and x- ray imaging technique is used to visualize liquid flow lines in the bed. Simulation results for liquid flow path compared with the experiments.

Jan 1, 2006

FOR some years past it has been usual to specify high-grade copper for use for many purposes, but the practice of specifying zinc of a high degree of purity for certain purposes is of comparatively recent origin. It is a practice, however, which is extending ag the effect of the impurities in zinc on products manufactured therefrom becomes widely recognized.The notes hereunder are intended to briefly survey the principal uses to which high-gr.ade zinc is being put, and, wherever possible, to indicate the effect of the impurities normally present in the lower grades of zinc.In the United States zinc is graded into five divisions, known respectively as "High-grade" "Intermediate" "Brass Special" "Selected," and "Prime Western." The maximum amounts of impurities allowed in the various grades are indicated in Table I,which is compiled from data published by the American Society of Testing Materials:In addition, it is specified in an cases that the slabs shall be reasonably free from surface corrosion or adhering foreign matter. Although zinc used in Europe has in many cases been sold on analysis it is only recently that any attempt has been made to grade...

Jan 1, 1923

By LaPoint D. J.

Copper deposits in sandstones are excellent targets for open pit mines using SX-EW extraction and processing methods. The mineralogy consists of chalcocite as the primary sulfide and copper carbonates and sulfates in the zone of oxidation. Two general deposit types are recognized: early diagenetic copper deposits that are associated with the reddening of the surrounding sediments, and epigenetic deposits that are associated with the migration of copper-rich basinal fluids along faults into permeable reservoir beds with a source of reductant. Epigenetic copper deposits are more likely to contain enough tonnage to be economic.

Jan 1, 1996

By X. Zhang, E. Li, Y. Xiao, Z. Yu, H. Han, J. Xie, J. Tian, W. Sun, K. Hong

In a pulp environment, the surface properties of magnesite and dolomite tend to be similar, due to the re-adsorption of dissolved calcium species, which makes the flotation separation difficult. In this paper, the chelating reagent EDTA is introduced to eliminate the adverse influence of the calcium species and to restore the selectivity of magnesite-dolomite separation using sodium hexametaphosphate (SHMP) as a depressant. Flotation experiments confirm that the recovery of magnesite improves significantly in the presence of EDTA. Zeta potential experiments confirm that the negatively charged EDTA4+ and HEDTA3+ species can form soluble and stable chelates with positively charged Ca2+ and Ca(OH)+ species preventing their adsorption on the magnesite surface. Adsorption measurements prove the addition of EDTA can decrease the adsorption of depressant SHMP on the magnesite surface. X-ray photoelectron spectroscopy (XPS) measurements further confirm the transformation from the surface of magnesite to dolomite in the presence of calcium ions, and the possible adsorption mechanism of EDTA and SHMP on the magnesite and dolomite surface. Key words: Magnesite; Dolomite; Surface dissolution; Flotation separation

Jan 1, 2020

By K. Sakaguchi, T. Yokoyama

"In-situ rock stress measurement was carried out in the Kamaishi mine of Iwate Prefecture to quantify the variation of the shallow crustal stress field associated with the 2011 Tohoku-oki earthquake. Stress measurement was conducted by the Compact Conical ended Borehole Overcoring (CCBO) technique, which is one of the stress relief method. The CCBO technique is the one of the suggested method of ISRM. Measurement period is from 1991 to 2014. Main results obtained in this study can be summarized as follows.The direction of the maximum principal stress did not change much before and after the earthquake. However, the directions of the intermediate principal stress and the minimum principal stress of one year after the earthquake changed from those of before earthquake. Namely, the direction of intermediate principal stress was East-West horizontally, and the direction of minimum principal stress was vertically. This state of stress is reverse fault type and was maintained for three years after the earthquake.The magnitudes of principal stresses and the vertical stress of one year after the earthquake became more than the double before the earthquake. However, the magnitudes of the maximum principal of two year after the earthquake became smaller comparing with those of one year after the earthquake. Furthermore, the magnitudes of the intermediate principal stress and the minimum principal stress of two year after the earthquake became almost same as those before earthquake, and the vertical stress of two year after the earthquake became almost equal with the overburden pressure. And the magnitudes of three principal stresses of three year after the earthquake became the same level before the earthquake."

Jan 1, 2015