Search Documents

The Queensland Magnesia Project is based on a unique cryptocrystalline nodular magnesite orebody which required an innovative approach to process design in order to economically exploit the characteristics of the ore and produce a marketable range of high quality refractory magnesias for a declining world market. High quality natural refractory magnesia must have an MgO content in excess of 95 per cent with a very strictly controlled content and ratio of residual impurities such as calcium, silica and iron. The natural products compete with magnesias derived by chemical extraction from sea water or brines which exhibit very high purity but often lack other characteristics which are of value to refractory brick makers. Since start up in late-1991 QMAG has achieved a remarkable market penetration for both its deadburned and electrofused products with sales for the 1993/94 financial year representing 92 per cent of deadburned capacity and 138 per cent of original electrofused capacity respectively, all at a time when the world steel industry has been in recession.

Jan 1, 1995

By R. Gradnik

The continuous need for infrastructure expansion forces the mining industry to develop underground structures into more sensitive and violent environments. When underground excavation enters into deep and high stress rock conditions, geotechnical designers find themselves faced with the difficult task of selecting a rock support system that will meet today's stringent requirements. Whatever support system is chosen, it is mandatory that potential rock movement be controlled. All this has intensified the development of safety systems and new, unique solutions which can enable construction companies to go both, further and deeper, without reducing the level of safety. To address these needs, Atlas Copco developed the Roofex® bolt, specifically designed to withstand large static and dynamic deformations under prespecified load conditions. The Roofex Rock Bolt acts as stiff support up to a designable load level before the sliding effect of the mechanical frictional system is triggered and allows highly controlled rock mass movement without loosing the support function.

Jan 1, 2011

By Leslie G. McMillion

A field project to develop and demonstrate a method for alleviating problems of highly mineralized ground water where they occur as isolated zones or pockets in fresh-water aquifers is being conducted in the Ogallala aquifer of eastern New Mexico by the Robert S. Kerr Water Research Center. Removal of contaminated water is by a large-capacity well and the pumped poor-quality water is used locally for secondary recovery of oil. Benefits of the operation are threefold in that the aquifer is being reclaimed for future fresh-water production, contaminated water is being used beneficially, and fresh water which otherwise would have been used for waterflooding is available for other purposes. Ground-water quality in the site has improved markedly after two years of operation. Use of water in the arid and semiarid Southwest has grown so rapidly that demands in many localities far exceed available supplies. In the High Plains region of New Mexico, Oklahoma, and Texas, the only large sources of water are underground reservoirs, being depleted at an alarming rate. In some parts of this region, the aquifers contain pockets of highly mineralized waters; and the mineralized waters in some of them have started spreading in response to the drawdown effects of pumping wells. The aquifers of this region are primarily composed of sand and gravel beds; any cleanup by natural processes will require many tens or even hundreds of years. Most of these pockets of highly mineralized water were caused by oil-field brines seeping downward from earthen disposal pits. Thousands of these pits were in use in the region until only a few years ago when they were prohibited by the oil regulatory agencies of the respective states. The resulting areas of poor quality water are serious enough to warrant much corrective attention. Correction will involve one or more of three approaches: 1) Restrict the pumping of fresh water in the zones where the drawdown of the pumping well will significantly influence the movement of the contaminant. 2) Remove the highly mineralized water entirely from the affected area. 3) Develop and pump the poor-quality water in such a manner that its movement is held in check, even though only a part of the contaminant is actually removed. The principal hurdle to overcome in applying methods 2 or 3 is financing of the operations, since there are very

Jan 1, 1972

By Laurentiu Nastac, Ruslan Mudryy

"This paper investigates the solidification of cast energetic materials. An active cooling and heating (ACH) technology and a mechanical vibration (MV) technology were applied to achieve unidirectional solidification during casting and to reduce cracks, gas pores, and shrinkage defects. The design parameters of these technologies were developed via Computational Fluid Dynamics (CFD) modeling and thermal stress analysis. Concerning the ACH technology, the number of cooling/heating sections and their temperature profiles and time sequences were optimized based on the thermo-physical properties of the energetic material as well as the riser and mold diameter, thickness and type. The ACH technology will also decrease the thermal stresses during casting of energetic materials and therefore minimize the formation of potential cracks that may form during the casting process. The MV technology will help to remove air entrapped during pouring process and decrease the detrimental gap size between the projectile and the solidified energetic material.IntroductionCasting processes are widely employed in the manufacture of products with intricate shapes and, in particular, in applications where the material of the final product is sensitive to machining. It is especially useful in processing of energetic materials. The cooling conditions applied in the casting process can affect the quality of the final cast in terms of void formation, residual stress distributions, and mold separation. Substantial shrinkage is also observed due to the density change upon solidification [1-3]. Residual stresses are known to be closely related to the formation of cold cracks and hot tears during casting. The formation of a gap between the mold and the cast material is of critical importance due to its deleterious effect on heat removal and on crack formation. In the casting of energetic materials all these defects can significantly impair the detonation velocity, Gurney energy, and insensitive munitions characteristics of the formulation, and lead to catastrophic accidents in explosives handling [ 4-5]. Imposition of carefully controlled cooling condition is thus critical in optimizing the cast quality that could help avoid such destructive effects."

Jan 1, 2013

By Earl R. McMillan

"Coal washing commands the thoughtful attention of a steadily incre in number of people. Clean coal is not merely a luxury but is rapidly becoming a necessity in some industrial operations.Coal seams in the Northeast are rarely free from ""bone"" and shale or clay partings which vary from a fraction of an inch to several feet in thickness. Nearly all of the coal measures are folded and faulted, the coal seams dip at various angles, and in some cases are badly broken. In mining these seams fragments of the roof and floor, as well as partings of impur-ities within the seams, unavoidably become mixed with the coal, so that the raw coal as it comes to the surface often contains as much as 50 per cent, by weight of waste.At the Bureau of Mines experiment station at Seattle, the washing of this coal in order to improve it for commercial use has been studied. Since the process of coal-washing depends upon differences in specific gravity between the clean coal and, its associated impurities, the first problem undertaken was that of determining the specific gravity of the clean coal and of each parting of impurity contained in a large number of representative seams.It was found that the freshly-mined coal is practically saturated with water, this being observed in determining the effect of moisture content upon the specific gravity of the coal particles, selected from samples of coal varying from low-grade subbituminous up to semianthracite, all of which are found in the State of Washington. The specific gravity values determined for the cleanest particles varied from 1.28 to 1.35; in general, the higher the rank of the coal the hither the specific gravity."

Nov 1, 1920

By Catherine Cai

A granular sorbent, prepared by gel-coating polyethyleneimine (PEI) on high surface area silica followed by crosslinking with a low-molecular weight diepoxide, has significantly higher uranium capacity, greater salt tolerance, and faster kinetics than the commercial resin Dowex 21K. Though having lower U(VI)/Fe(III) selectivity than Dowex 21K, the gel-coated PEI affords much higher sorptions of both U(VI) and Fe(III) and also their separation by selective stripping with acid.

Jan 1, 1999

By Claude MacDonald, John H. Ashburn

"IntroductionIndustrial growth and technological change over recent years had been accompanied by two major sources of concern to management and employees: (a) increase in occupational injury and illness and the resultant costs involved; and (b) equipment damage and breakdowns in concentrated production lines causing more extensive loss potential.Due to economic factors, management attention has focussed more on production and quality than on safety, health and related loss potential sources. As a result , occupational safety and health activism has grown, government legislation of compensation and occupational safety and health standards have progressively developed and stronger liability attitudes have been taken by courts of law.To improve efficiency and allow development in more competitive markets, rising labour costs, equipment costs and safety related financial losses have dictated that attention be given to conservation of all resources. Conservation of resources, people, equipment, material and environment, can no longer be addressed in isolation but must be managed integrally with production and quality. To this end, systems have developed utilizing sound management principles applied with equal intensity to production, quality and loss potential"

Jan 1, 1987

By Aly M. Mohammad

The 12th and 14th Street Viaducts, which carry Route 139, are located west of the Holland Tunnel in Jersey City, New Jersey. The two viaducts, provide access to and from the Holland Tunnel (which connects New York City and New Jersey) and carry upwards of 50,0000 vehicles per day from Jersey City and New York City to points west. The New Jersey Department of Transportation (NJDOT) selected AECOM to perform design services including rehabilitation and seismic retrofit for the 12th Street and 14th Street Viaducts while maintaining traffic at all times. Building a new parallel bridge just north of the 14th Street Viaduct was essential in avoiding extremely costly traffic delays. Installation of the new foundation, in close proximity to the existing viaduct, required drilling through some of the existing timber piles supporting the bridge. As a result, the existing bridge was required to be reanalyzed for this new foundation configuration. This proposed structure consisted of 8 piers each supported on a single six (6) foot diameter drilled shaft. Currently this portion of the bridge structure has been constructed. The shafts were constructed with rock sockets that were five feet six inches (5?- 6??) in diameter and were extended 11.2 feet (3.4 meters) into rock. A 2300 ton Osterberg Load Test was performed on one production shaft to confirm the capacity of the shaft. The rock socket for the test shaft was in sandstone. This paper will present a description of the design methodology and construction methods adopted for the foundations. In addition, the paper will illustrate the Osterberg Load Test including: equipment used, number and locations of strain gages, and interpretation of results. Additionally, regarding the close proximity of the new foundation, the paper will present the type of equipment used to drill through the existing timber pile foundation while minimizing the impact on the integrity of the existing foundation. We will also present the method of analysis for analyzing the redistribution of load on the remaining piles. The results presented in this paper will assist the design engineer by providing a comparison between the geotechnical design assumptions and the actual measurements obtained by field measurements for this rock formation.

Jan 1, 2009

By G. Piegols, J. A. Lombardi

Substantial volumes of cyanide are consumed in precious metals mining due to the purposeful destruction of base metal cyanide complexes and free cyanide to meet surface discharge regulations. This destruction of cyanide resource runs counter to the prevailing social ethic of resource conservation wherein cyanide recovery-and-reuse is considered a more socially responsible cyanide use pattern than systematic cyanide destruction. HW Process Technologies, Inc. (HWPT) has developed membrane based methods for the recovery of cyanide from barren solution as a means to reduce cyanide waste. The HWPT Engineered Membrane Separation (EMS™) system uses state-of-the-art spiral wound membrane elements that are engineered specifically for the treatment of high pH cyanide process solutions. The membranes fully reject WAD CN, SAD CN and most minor metals, and partially reject SCN, Free CN and precious metal cyanide from a high clarity barren solution feed to a small volume EMS™ “concentrate” stream. The EMS™ “concentrate” stream is returned to the process. The large percentage of the EMS™ process feed exits the system as cyanide lean EMS™ “permeate.” The EMS™ permeate, after residual cyanide destruction, polishing, and pH adjustment, is, thereafter, typically suitable for discharge. Separately, the HWPT EMS™-PLS method of cyanide recycling is an internal plant cyanide recovery step that removes base metal cyanides from a pregnant leach solution to a small volume EMSTM concentrate stream. The concentrate stream is then typically processed further for the recovery of metals and recovery-recycling of cyanide. The method makes it economically practical to recover gold from Merrill-Crowe or car-bon plant “fouling” solutions, e.g., those with greater than 400 ppm Cu, as might result from the use of the EMS™ method wherein EMS™ concentrate is constantly thrown back into the mine leach solution pool as part of the free cyanide recycle process, or as might result from the single-pass leach treatment of high copper content ores or concentrates. The EMS™ cyanide recovery method for barren solution treatment is shown to be “economic” for the treatment of clear solutions at the approximately 200 ppm total cyanide level (CNT), and for slurries at the approximately 400 ppm total cyanide level, where economic is defined as a 2 year EMS™ plant payback. The EMS™ plant payback calculation includes the beneficial monetary impacts of gold and free cyanide recycling and the avoided operating cost of cyanide destruction.• The cyanide recovery plant payback period is reduced further when the avoided capital costs for cyanide destruction (EMS™ permeate “clear solution CN destruction polish” only required) and/or metals precipitation are considered.

Jan 1, 2004

By R. Macleod, G. G. Bursey, T. R. C. Aston, J. E. Gale

In 1991 the problems of water inflow at the mine were addressed by a three-phase study. A three-dimensional finite-element computer code, CFEST (Coupled Fluid, Energy and Solute Transport), was used to model the system of groundwater flow around the mine, allowing assessment of the nature of the hydrological regime and of the various recharge mechanisms and sources of inflow. A regional (111 km2) model was used to simulate conditions of low to average mine inflow and provide boundary conditions for the subsequent local (16.8 km2) model. The regional model produced inflows of 0.26 m3/s and the local model 0.25 m3/s. With the use of constant head conditions to simulate a saturated flood plain along the Gays River and on doubling the rate of surface recharge, the local model produced a maximum mine inflow of 0.255 m3/s, in contrast to a measured peak mine inflow of 0.37 m3/s. The discrepancy suggests that during periods of high river level surface water gains access to features with high permeability, such as sinkholes, that may be connected directly or indirectly to the mine workings. Improved simulation of high inflow conditions can probably be achieved by determining the hydraulic conductivity of the river-bed and flood-plain sediments and modelling known sinkholes as discrete units. Possibilities for controlling the amount of inflow to the mine include sealing the flood plain with dykes, checking regularly for new sinkholes, which should be filled and capped, maintaining adequate mine drainage, and monitoring well levels and pressures on a continuous basis.

Jan 12, 1993

By George H. Schnakenberg

This Bureau of Mines publication describes a passive personal sampling device for N02 in air, developed by the New York University Medical Center under Bureau Grant G0133066. The sampler has been successfully demonstrated in the field and in the laboratory. In corroborative laboratory trials the agreement with reference method is excellent. The overall accuracy is approximately ±5 pct of reading to a precision of about ±l pct. All evidence indicates that these samplers should indicate the time-weighted-average N02 concentration to the above accuracy and precision equally well in the field since effects of wind velocity and relative humidity are negligible and the effects of temperature are about 0.1 pct per °F. The duration of exposure and the approximate temperature are the only data that need to be collected in the field. A two-step analysis procedure in field or service laboratory is then used to obtain the total cumulated exposure to N02 in parts per million-hours (ppm times hours), which can be converted to the time-weighted-average concentration of N02 in ppm by dividing cumulated exposure by the duration of the exposure.

Jan 1, 1976

By J. W. Thompson

MINERALS OWNERSHIP AND POSSESSION. The owner of minerals under a conveyance from the surface owner does not lose his right or his possession by mere nonusage of the minerals. McBeth v. Wetnight (Indiana), 106 Northeastern, 407, p. 410, October, 1914. QUIETING TITLE TO MINERALS-PLEADING. A complaint in an action to quiet title to minerals and to the min- eral rights in certain land is insufficient in the absence of a direct allegation of possession, although it avers that the plaintiff from the time of receiving the conveyance assessed the mineral interest for taxes each year and paid the taxes thereon and exercised various acts of ownership of such mineral interests, in that he caused test pits to be dug on the land for the purpose of exploring the minerals and ascertaining their quality and extent, in going upon the land and looking after them from time to time, and that he accompanied or caused his agents to accompany prospective purchasers of such mineral interests and exhibited the same to such prospective pur- chasers in efforts to sell them. Fowler r. Alabama Iron & Steel Co. (Alabama), 66 Southern, 672, p. 673, Novem- ber, 1914. SALE BY MARRIED WOMAN-VALIDITY. A conveyance by a married woman of the mineral rights in certain described land is void where she had previously conveyed the land to another grantee who had acquired title by adverse possession under the deed.

Jan 1, 1915

By Kenji Monden

A simple technique is presented to evaluate optical property of biomimetic microlens array (BMA) as an antireflective surface on a polydimethylsiloxane (PDMS) sheet. The integration of these structures is done by a thermoforming process. We have only UV-VIS spectrophotometer for optical evaluation apparatus. The transmittance of the sheet is measured with angled sample holder. The 50 deg. transmittance of 270nm pitch BMA on PDMS sheet increases from 87 to 92% after the moth-eye structure is introduced. The transmittance of 350nm pitch BMA on PDMS sheet increases from 87 to 96% after the moth-eye structure is introduced. The transmittance increases with increasing pitch of BMA. The results obtained using UV-VIS spectrophotometer with handmade sample holder.

Jan 1, 2015

By T. R. Wildeman

"At the Big Five wetland, which was built to treat drainage from a metal mine, encouraging results have attributed to sulfate reduction. Cu and Zn were reduced to below detection limits of 0.50 mg/L, Fe was reduced by at least 90% to below 3 mg/L, and the pH was raised from below 3 to above 6. The study showed that treatment was primarily through microbial processes within the substrate and that plants were not needed to insure success.Constructed wetlands can be taken through design and proofing stages, and into operations scale in a meaningful time frame for on-line acid drainage remediation. In staged design, laboratory experiments are initiated to determine reasonable substrate materials for remediation of a particular drainage. When a reasonable substrate is found, bench scale experiments are initiated as the next stage in the design. In these studies, removal efficiency, permeability, and flow are analyzed to identify candidate substrate which will support sulfate reduction and be hydraulically reasonable. Using this design method at one site, an acid drainage of pH 2.5 was raised to a pH of above 7. Total heavy metal concentrations in this drainage exceeded 900 mg/L. In the pilot constructed wetland Cu, Zn, and Fe were reduced by 99%.Determining how well these anaerobic cells operate in the winter is done at the pilot plant site in Idaho Springs, CO. It's been found that over the last four winters, those cells that emphasize anaerobic removal within the substrate have operated continuously and effectively the year round. Winter operation is aided by the fact that the water temperature of the acid drainage is always between 14 and 16° C, and the cell can be readily insulated from the cold. Activity of the sulfate reducing bacteria may decrease during the winter. However, it appears that organic complexation of metals helps to maintain low concentrations of metals in the effluent."

Jan 1, 1992

By Kerby Glass, Glenn A. Gruber

Mr. C. A. Hollingsworth introduced commercial column flotation to the Florida Phosphate Industry in 1976, with a six feet diameter prototype cell at the Tenoroc Mine. More than two-dozen column cells have been installed in phosphate beneficiation plants since then. The increased interest in column cells for phosphate flotation, and their potential use in new plant construction, prompted the Florida Institute of Phosphate Research to fund programs to investigate various aspects of column flotation. This report describes a test program, conducted by JACOBS at CF Industries Hardee Complex II, as part of a comprehensive research program awarded to the University of Florida by the Florida Institute of Phosphate Research. The 1.5 feet diameter test column was operated with plant process water and plant reagentized flotation feed. Several variables considered for column cells design and operation were tested. Feed specific capacity, air superficial velocity, and the length to diameter ratio of the column were the variables that influenced phosphate recovery. Concentrate phosphate grade was influenced by concentrate superficial velocity and feed specific capacity.

Jan 1, 2002

By P. F. Kinyoun

MANY interesting new features are embodied in the latest extension to the open-hearth department of the Bethlehem Steel Co., at Lackawanna, N. Y. Automatic control of the important factors in furnace operation-fuel, air, draft, pressure, slag composition, and of the temperature in various regions of the furnace-has been carried out to a remarkable degree; the human factor is minimized, and the chances for mishaps and irregularities in operation are greatly reduced.

Jan 1, 1937

By Andre Zingano, Anderson Weiss

"The objective of this paper is to study the behavior of a low thick and low depth coal seam and the overburden rock mass. The mining method is room and pillar in retreat and partial pillar recovery. The excavation method is conventional drill and blast because of the small production. The partial pillar recovery is about 30% of the previous pillar size, 7m x 7m. The roof displacement was monitored during retreat operation; the surface movement was also monitored. The effect of the blasting vibration on the final pillar strength had been considered. Due to blasting, the pillar reduced about 20%. The consequence is more pillar deformation and roof vertical displacement. The pillar retreat and ground movement were simulated in a three-dimensional numerical model. This model was created to predict the surface subsidence and compare to the subsidence measured. This study showed that the remaining pillar and low seam reduce the subsidence that was predicted with conventional methods.INTRODUCTIONMining low coal seams (less than 1 meter) with the room-and-pillar mining method implies the excavation of part of the roof or floor to maintain adequate entry height for equipment and compliance with labor regulations with respect to ergonomic issues. The direct consequence of this is an increase in coal contamination and the increased cost of transportation and preparation at the plant. Traditional room-and-pillar mining only uses a development operation, even with a continuous miner or drill-and-blasting. Therefore, all the run of mine (ROM) coal is carried out with part of the roof or floor. However, if the retreat mining method were to be considered, the quality of the coal could increase because only the coal seam is excavated from the pillar recovery. The quality of ROM coal will increase, and the cost will decrease proportionally to the amount of coal produced from the retreat operation.However, the retreat mining with partial or total pillar recovery implies greater subsidence. This is particularly true if the coal seam depth is shallow, under 100m depth. Subsidence prediction in room-and-pillar retreat mining is complex; it depends upon the remaining pillar (stump pillar) size, as well as the pillar height, and the behavior of the pillar after retreat. This is related to the strength of the remaining pillar, which is related to the excavated method (drill-and-blast or mechanical)."

Jan 1, 2018

By A. S. Romaniuk

More than a decade ago, CANMET management recognized the need to make better use of existing technological information in mining and extractive metallurgy-two fields basic to the economic well-being of Canada. There were at that time no indexes or files dedicated to disseminating technical information for the many minerals mined and processed in Canada, including coal. CANMET, with the nation's largest research and library resources in the minerals field, was in a unique position to fill this need. Initial efforts were concentrated on building a mining file, beginning with identification of world sources of published information, development of a special thesaurus of terms for language control and adoption of a manual indexing/retrieval system. By early 1973, this file held 8,300 references, with source, abstract and keywords given for each reference. In mid-1973, operations were computerized. Software for indexing and retrieval by batch mode was written by CANMET staff to utilize the hardware facilities of EMR's Computer Science Centre. The resulting MINTEC file-one of the few files of technological information produced in Canada-is the basis for the national literature search service in mining offered by CANMET. Attention is now focussed on building a sister-file in extractive metallurgy using the system already developed. Published information sources have been identified and a thesaurus of terms is being compiled and tested. The software developed for CANMET's file-building operations has several features, including the selective dissemination of information and production from magnetic tape of photo ready copy for publication, as in a bi-monthly abstracts journal.

Jan 1, 1979

By M. G. Gorman

The effects of particle size, particle shape and degree of aggregation on n-dodecylamine flotation of -20 µ m quartz and glass beads were studied. A microflotation cell suitable for use with very fine particles was used in the flotation experimentation. Degree of agglomeration of particles was estimated by comparing size distributions of the quartz and beads in a dispersed system to size distributions in systems in which the collector was present. Results obtained show that in such flotation systems the fine particles are not generally present as individual particles during flotation but rather as aggregations. However, the quartz floats more readily than the beads indicating that there are some shape effects in the systems, considering the large specific surface areas of the materials it also appears that substantial amine consumption in the systems may limit flotation or lead to a requirement of greater reagent dosage for equivalent flotation to that tor larger particles.

Jan 1, 1990

By K. Moxham, B. McKeown

The South African gold and platinum deposits were formed in very different ways and yet both have many similarities. They are flat dipping tabular orebodies, extremely narrow and located in hard abrasive country rock. The mining methods employed are also similar. Primary access is via shafts or declines; secondary access is via haulages and cross-cuts; and tertiary access is from raises. The proposed solution for rapid access described in this paper is focused on the haulages and cross-cuts.

Jan 1, 2006