Search Documents

By R. G. Knickerbocker, A. L. Fox, J. Koster, P. R. Perry

"During the past several years, alunite from the Marysvale (Utah) region has been the subject of investigation by the Electrometallurgical Section of the Bureau of Mines. The nature and occurrence of this mineral, with considerable data on the Utah deposits, together with a number of results of preliminary experiments, have been given in a previous report. 6/ The geology of the Marysvale region has been reviewed recently. 7/The present paper reports the results obtained by a method involving the sintering of alunite with boric acid and subsequent treatment of the sinter to produce alumina and potassium sulphate.The preliminary work just mentioned had given indications of the separation of sulphate salts high in potassium from fusions of alunite with borax glass.During the course of further work along those lines, fusions of boric acid and alunite were tried. No separation of salts was obtained, but it was observed that rather complete removal of so3 from the alunite occurred and that the sinter could be leached with water to give a solution contain¬ing most of the potash and a residue containing most of the alumina. The reaction that takes place can probably be written 8/:"

Mar 1, 1939

By J. G. Groppo

Hyperbaric filtration was evaluated at the laboratory scale for dewatering fine coal cleaned by froth flotation. A laboratory pressure filtration procedure is described to obtain uniform cake structure from dilute slurries containing a significant amount of coarse material. Baseline tests were conducted varying filter operating parameters such as driving force, time, cake thickness, percent solids, viscosity and pH to determine optimum operating conditions for eventual application on a continuous pilot scale hyperbaric filter.

Jan 1, 1994

By G. M. Potter

During investigation of the occurrence of manganese deposits in the western United States, the Bureau of Mines collected 2-ton samples of 4 ores from 3 properties in northeastern Nevada. Laboratory tests were made to determine the amenability of these ores to ore-dressing methods of concentration. The Caviglia-Vietti property is situated 11 miles southeast of Ely, White Pine County, Nev. The ore deposits are lenticular veins and irregular masses found in limestone fracture zones and along the contact of limestone and underlying shale. Two samples, of the ore were tested: Lot A, from the Vietti shaft, and lot B, from the. Caviglia shaft.

Jan 1, 1954

By V. ?. Chanturiya, I. Zh. Bunin, M. V. Ryazantseva

"Surface changes in naturally occurring metal sulfides (pyrite, arsenopyrite, sphalerite, chalcopyrite, galena, and molybdenite) due to treatments from high-power electromagnetic pulses (HPEMP) at varying times were studied using X-ray photoelectron spectroscopy. Analysis of the obtained results revealed common patterns and differences in surface transformations. The transformations were found to include two main stages. The first stage was observed at low treatment intensities (up to n ~103 pulses). At this stage, formation and accumulation in the surface layer of the nonstoichiometric sulfide phase, oxides and hydroxides, as well as elemental (polysulfide) sulfur and/or metastable sulfur species (thiosulfate, sulfite) was observed. The second stage (N = 3·103 pulses) is characterized by thermal removal of sulfur species and renewal of the mineral surface (sulfidization).It was found that the chemical changes of the sulfur on the surface layer of pyrite, arsenopyrite, chalcopyrite included accumulation/formation of S0 (Sn 2-) at the first stage of the transformation, followed by its removal. An increase in the surface concentration of elemental sulfur for pyrite and chalcopyrite was 10–12% while arsenopyrite was approximately 5%. A more complicated chemical change was observed for sphalerite and galena, that included formation/accumulation of metastable sulfur species (thiosulfate, sulfate) at the initial stage (up to 103 pulses) and during longer treatment times, the sulphur is reduced back to its initial state (sulfide or disulfide). The increased concentration of S0 sulfur, compared to the original sample, was only 3% in galena and sphalerite.The application of HPEMP treatment to improve flotation selectivity is supported by singlemineral flotation tests. Changes in flotability as a result of HPEMP treatment are principally explained by surface phase changes that resulted in higher adsorption activity."

Jan 1, 2016

By D Connelly

Silver and gold bearing ore from the Troy Resources NL Casposo Gold-Silver Project, located within the San Juan Province of Argentina contains a complex mix of gold, silver, electrum and silver sulphides in the ore. Casposo is a typical low sulphidation epithermal style gold–silver deposit where mineralisation is hosted within rhyolite – andesite flows and breccias. Veins are typically banded quartz–chalcedony colloform - crustiform banded with quartz - carbonate infill. Mineralisation is associated with an assemblage consisting of quartz, chalcedony, adularia, calcite, illite, sericite and trace sulphides. Gold and silver occur as electrum, native silver, sulfosalts and silver sulphides. This paper presents a case study that describes the process selection, development and engineering of a tailored process plant for the recovery of gold and silver from this ore.The original feasibility study, modelling, metallurgical testwork and engineering studies are outlined. The final flowsheet was based on minimising capital cost, operability, recovery and minimising technical risk.The process flowsheet uses the traditional Merrill Crowe route because of the high silver to gold ratio in the feed and achieves maximum gold and silver recovery while providing a common facility for future ore body treatment.

Aug 8, 2011

By L. M. Chan, D. H. Carlson, J. H. Johnson

"This paper discusses the evaluation and application of a portable parked-vehicle tailpipe emissions measurement apparatus (EMA). The EMA consists of an exhaust dilution system and a portable instrument package. The EMA instantaneously dilutes and cools a sample of exhaust with compressed nitrogen or air at a known dilution ratio, thereby presenting it to instruments as it is presented to personnel in the surrounding environment. The operating principles and governing equations of the EMA are presented.A computational method is presented to determine the engine operating and performance parameters from the exhaust CO2 concentrations along with an assumed engine overall volumetric efficiency and brake specific fuel consumption. The parameters determined are fuel / air ratio, mass flow rates of fuel, air and exhaust emissions, and engine brake torque and horsepower. These calculated engine parameters are used to characterize engine load when performing EMA in-field tailpipe sampling without a dynamometer, and to detect deteriorated engines.Evaluations of the EMA by comparison of diesel tailpipe measurements with those made using laboratory-grade instruments showed that the EMA measurements are accurate and reproducible. The results also show that the EMA is capable of detecting emission concentration changes resulting from engine faults. Calculated engine operating and performance parameters correlate and compare well with laboratory-measured values.The EMA in-field engine loading and tailpipe sampling procedures for parked vehicles are presented, and results of the EMA field measurements are also presented. Low coefficients of variation for repeat EMA tailpipe measurements on diesel-powered haulage vehicles in four underground mines indicate that the EMA in-field engine loading and tailpipe sampling procedures are reproducible.An analysis of EMA tailpipe measurements for three haulage vehicles in one mine shows that the EMA can: 1) identify haulage vehicles that emit excessively high pollutant concentrations, and 2) provide data needed to evaluate and determine the efficiency and effectiveness of tailpipe emission control devices.Finally, recommendations for a proposed commercial EMA system are presented. This commercial system would overcome many of the adverse features of the prototype EMA used in these tests."

Mar 1, 1992

By Timothy J. Matthews, Timothy J. Batchler, Ted M. Klemetti

"From 2011–2016, there were 1,511 documented injuries, including 7 fatalities, from ground falls in underground coal mines in the United States. The majority of these ground-fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely used in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program using the Mine Roof Simulator (MRS) in Pittsburgh, PA.The load-displacement characteristics of an 8-ft x 12-ft panel of 8-gauge welded screen were evaluated using a newly designed, large laboratory screen test frame with multiple load pull locations. This screen was tested in a configuration that simulates current installation practices in U.S. coal mines. In this study, the effects of varying the number and position of the load pull location on the screen performance were evaluated. Ultimately, the type of information obtained in this and similar studies can be used to aid in developing wire roof screen design criteria and to assist mine operators in the selection and use of roof screen in underground mines.INTRODUCTIONThe large majority of ground-fall injuries are caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Compton et al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program in the Mine Roof Simulator (MRS) in Pittsburgh, PA."

Jan 1, 2018

By M. Leahy

"Very little is known about the large scale fluid dynamics and associated distribution of copper in an operating electrowinning cell, yet they will have a major influence on mass transfer and plating quality. The CFD model in this work is used to simulate an entire EW cell with 60 cathodes and 61 anodes, or 121 anode–cathode pairs, elucidating for the first time the three-dimensional (3D) flow and copper distribution in an industrial cell. Two methods for the distribution of electrolyte are modelled:1. Downcomer method: electrolyte is fed by a downcomer at one end of the cell, overflowing at the opposite end.2. Manifold method: a horizontal manifold pipe runs the whole length of the cell and feeds electrolyte via small holes in the top of the manifold pipe.The recirculation that develops within each anode-cathode pair, driven by oxygen bubble generation on the anode, is similar to that seen previously in two-dimensional models of single anode–cathode gaps. However a more complex 3D flow recirculation is established, which involves flow of electrolyte down the side gaps (being a path of low resistance for return flow) as well as the usual return flow down the cathode side of each pair gap. The bubble-driven flow is not influenced by the mode of electrolyte distribution.The electrolyte flow due to the manifold and downcomer is somewhat secondary to the bubble driven flow. In the case of the downcomer distribution mode, the high injection velocity causes a very turbulent flow in the first 1–2 m down the cell from the downcomer, with several large vortices developing. This may lead to some sludge particles being entrained into the bulk of the cell.In the manifold pipe case, the jet from each hole is dissipated very quickly, within the first 10–20 cm. The jets are directed into the downward flowing zone of the bubble-driven recirculation, which leads to unstable and periodic behaviour on a large spatial scale.In both the manifold and downcomer cases, there is a marked two-zone vertical stratification in copper concentration."

Jan 1, 2016

"Successive seismic waves may cause progressive weakening of a fault zone, which has been recognized as the mechanism of earthquake aftershocks. However, it is unclear that how a fault zone slips under each wave cycle and how slip displacement accumulates under continuous wave cycles. This laboratory study provides direct evidences on the slip process of a simulated granular fault zone dynamically induced by an incident wave without the effects of late-arriving and reflected waves. The experimental observations show forward and backward slip paths of the fault zone and partially recovered slip displacement after a wave incidence. The unrecovered slip displacement after each wave cycle can be accumulated until it reaches a critical slip distance for seismic faulting, which may reinterpret delayed triggering in earthquake dynamics. The limited interseismic period restricts fault self-healing in strength. The experimental results also indicate that the dynamically induced frictional slip on the fault zone is associated with a complex frictional system, including seismic wave radiation, frictional slip initiation and normal stress vibration. Different from the dynamically induced frictional slip on the fault zone, the statically induced frictional slip causes a permanent increase of slip displacement along the shear loading direction. INTRODUCTIONAn earthquake mainshock may induce aftershocks by suddenly changing external stresses applied to another fault zone in the near field (Kilb et al., 2000) and by slightly perturbing a fault zone from a critical steady state to stick-slip faulting in the far field (Gomberg and Davis, 1996). The dynamically induced frictional slip on a fault zone has been recognized as the mechanism of earthquake aftershocks (Marsan and Lengliné, 2008; van der Elst and Brodsky, 2010). Although earthquake aftershocks have been extensively studied by many seismological methods, a simplified laboratory fault zone can provide possible interpretation on real faulting and detailed analysis on a friction process (Dieterich, 1979; Nielsen at al., 2010). According to a few laboratory experiments related to the dynamically induced frictional slip on a simulated fault zone (e.g., Uenishi et al., 1999; Johnson et al., 2012), the slip process induced by successive seismic waves exhibits continuous motions. However, it is unclear that fault slip response under each wave cycle and slip displacement accumulation under continuous wave cycles."

Jan 1, 2015

COAL constitutes such a gigantic item in modern industry, either for direct heating, production of coke for smelting, or for the generation of power, that its quality and price play a very significant part in economic industrial progress. Australia is still a very young country industrially, and is groaning under many disabilities compared with competitors overseas, not the least of which is the quality of coal. Linked with the word "quality" should be that of "utility," for high-ash content prevents efficient utilization of the fuel.The marketing of good quality coal is a very important matter indeed, and if industry in Australia is to progress in the way that it should, this matter must receive keen attention.New South Wales, above all the other Australian States, has been blessed by nature with vast coal-fields, from which fuel is shipped to every State, and provides the base for power for most of our railroads and industries.Experts frequently refer to the fact that in some districts only partial extraction of thick seam coal is being made, without a care or thought for the future. Ranking next in importance to this is the fact that much of the coal is being carelessly marketed.Very few collieries in Australia are equipped with coal-washing plants for dealing more particularly with small coal grading which most industries require, and to which coal producers as a whole pay the least attention. In England each year nearly20,000,000 tons of coal is being water-washed before sale, and is marketed as a fuel of far greater utility once it has been freed from extraneous ash.Investigation proves that a great many pits in New South Wales are marketing coal (more particularly small coal) containing a considerable quantity of extraneous ash, due to the admixture...

Jan 1, 1926

By J. Zhang, A. J. S. Spearing, L. Ma

Ore deposits are becoming more complex to mine as a result of the exhaustion of surface and other easily mined deposits. There is also increasing socio-political pressure to design more environmentally sound, sustainable, and safe mining practices. Wang and Ma designed a mining method for coal, similar to a modified drift and fill using a continuous miner to take sequential cuts (rooms) that are subsequently backfilled. The authors have modified the concept to make it more autonomous, safer, and less costly using highwall coal mining techniques, modified and adapted for underground applications. The method is more flexible than longwall mining and the percentage extraction would seem to be in the same range. In addition because of the backfilling, surface subsidence would not be a major issue and could be more effectively managed.

Feb 2, 2021

By Güney

"An investigation carried out to determine the tendency of coals to heat spontaneously in terms of time-temperature curves coupled with the resulting oxidation products in an adiabatically controlled laboratory setup is described. Tests were made at differing moisture conditions, including oxidation and also oxidation with either adsorption or desorption of water vapour on coal.From the experimental evidence, there is reason to believe that the oxidation of coal, although an important factor, is not the predominant one in the development of spontaneous heating. In addition to the temperature increase in coal and the gaseous products evolved due to auto-oxidation, the process is accelerated by adsorption and retarded by desorption of water vapour on coal."

Jan 1, 1971

By Surendra Kumar Biswal, Sachida Nanda Sahu, B. C. Meikap

The unutilized iron ore fines (IOF, − 10 mm, 45% to < 60% Fe(T)) left at various mine sites during blasting and processing are rich in goethetic-hematite associated with high clay and considered a potential iron ore resource. The variation of loss on ignition (LOI) from mines to mines is based on the goethite and clay mineral content. The clay containing below 45 μm is mostly brittle, causing beneficiation problems. The IOF has an LOI of 7.83%, with high silica (5.52%) and alumina (4.57%), and 57.17% of Fe(T) subjected to both conventional deep beneficiation (CDB) and magnetization roasting using high-ash non-coking coal to adopt the suitable upgradation process. The CDB and magnetization roasting concentrate has 62.61% and 67.58% Fe(T) with 64.69% and 85.19% yield, respectively. However, the presence of 6.40% LOI in CDB makes the ore challenging for pelletization. Characterization like X-ray diffraction(XRD), scanning electron microscope(SEM), and chemical analysis was used to assess the concentrate quality and potential industrial application.

Jun 4, 2022

By Syd Peng, Gamal Rashed

"Bumps in coal mines have been recognized as a major hazard for many years. These sudden violent failures around mine openings have compromised safety, ventilation and access to mine workings. Previous studies showed that the violence of coal specimen failure depends on both the interface friction and width-to-height (W/H) ratio of a coal specimen. The mode of failure for a uniaxially loaded coal specimen or a coal pillar is a combination of both shear failure along the interface and compressive failure in the coal. Unstable interface failures provide a sudden de-confinement to coal rib, thus triggering uns and compressive failure in the sidewalls. The compressive failure of a coal specimen or a coal pillar can be controlled by changing its W/H ratio. As the W/H ratio increases, the ultimate strength increases. With a proper combination of interface friction and the width-to-height (W/H) ratio of pillar or coal specimen, the mode of failure will change from sudden violent failure, which is brittle failure to non-violent failure, which is ductile failure. The main objective of this paper is to determine at what W/H ratio and interface friction the mode of failure changes from violent to non-violent. In this research, coal specimens of width-to-height ratio ranging from 1 to 10 were uniaxially tested under two interface frictions of 0.10 and 0.25. The results are presented and discussed.INTRODUCTIONCoal mine bumps are sudden, violent bursts of coal from a pillar or pillars or a block of coal, resulting in a section, the whole pillar, or the solid block of coal being thrown into an open entry. These bursts are accompanied by very loud noises (Peng, 2008). Several case histories in mining have long described coal pillars or coal faces failing violently with an accompanying ejection of debris and broken material into the working areas of the mines (Campoli et al., 1987; Osterwald, 1962; Peperakis, 1958; Garvey et al., 2013). Because of the catastrophic nature of these sudden failures, understanding the causes of coal mine bumps is essential to create a safe underground working environment. This phenomenon has motivated many ground control researchers to conduct extensive field investigations throughout the past century. Rashed and Peng (2014) compared the mechanical properties of two kinds of coal, one from bump and the other from non-bump-prone mines. They found that coal itself does not play any significant role in coal bumps and recommended that future research should focus more on the local variation of geological conditions such as the interface friction between pillar and roof and between pillar and floor."

Jan 1, 2015

By A. Alwasel

Musculoskeletal disorders (MSDs) threaten the wellbeing and livelihood of a large number of construction workers incurring a significant cost to society. We present a new method to monitor and diagnose MSD risks in the workplace. The sensing unit of the system is an optical encoder encompassed within a non-intrusive exoskeleton to measure the joint angle of interest. This sensor can be applied to ball-and-socket and hinge-type joints of the human body, such as the shoulder, elbow, and knee joints. The system is contactless and does not require markers or cameras. Angle measurements are acquired directly without mathematical post-processing, thereby avoiding numerical noise and drift challenges. The system is a simple, robust, and deployable, but it currently lacks resolution of parallel degrees of freedom.

Aug 1, 2013

By A A. Latscha, D O’Connor

Increasing orebody complexity, restrictions in ground access, and longer lead times for disturbance approvals, have generated the need for the Resource Development Team within Rio Tinto Iron Ore (RTIO), to explore optimised drill design techniques that deliver resource conversion value while maximising program outcomes. In response to this challenge, the Team initiated a case study to produce an AI assisted/designed drill program using a non-machine learning AI. The case study involved the assessment and implementation of an AI generated drill program at one of RTIO’s Pilbara iron ore deposits, located in the Hamersley Province of Western Australia. The Mineral Resource is currently classified as 100 per cent Inferred. Access constraints inherent to topography, and the presence of exclusions zones have prevented adequate drilling coverage, resulting in lower resource confidence and a poor definition of the orebody extents and geometry. The drill campaign, planned in Q1 2023, needs to consider access constraints, complex topology and the limitations related to additional ground clearance, while addressing the requirement of improving orebody knowledge. The drill plan had to address two objectives. The first and main aim of drilling was to upgrade the Resource Classification to allow for possible conversion to Ore Reserve. The input for this objective was a volumetric representation of the areas currently not meeting pre-defined quantitative Resource Classification upgrade criteria. The second objective was to better define the orebody extents and geometry. For the second objective, the input to the drilling optimiser was a volumetric representation (blocks) of the areas of high uncertainty in the mineralisation/waste boundary, which were defined using an indicator conditional simulation technique. The drilling optimiser output was a range of compliant drill plans. A set of KPIs based on economic and orebody knowledge criteria were used to assess the plans and to select the most optimal drill design to be drilled in 2023. The geology and management teams were able to make better informed, objective decisions using the trade-off between cost and orebody knowledge gained. As part of the assessment, the AI generated plans were compared to our current planning practises. The AI assisted plans, when gauged against the project KPIs, showed clear and measurable improvements in both meeting project objectives and in managing operational risk.

May 24, 2023

By John W. Chandler

The property of the lava Cap Gold: Mining Corporation is in the Nevada City-Grass Valley mining district about 5 miles east of Crass Valley, Calif. At present (July 1940) the plant is mining end milling about 390 tons of gold-silver ore a day; about 310 men are employed. This paper describes the mining methods used and presents mining costs for 1939, when 60,704 tons were mined by cut-and-fill stoping and 55,676 tons by square-setting.

Jan 1, 1941

By D. D. Bell

This paper presents the history of uranium procurement and demand, and takes a look at future requirements. The three basic conclusions drawn are: (1) the productive capacity of former and existing producers whose operations may be profitably reactivated is insufficient to meet demand projected beyond 1975; (2) reserves in the $5 -$10 price range do not provide the flexibility to sustain production at the high rates required in the late 1970's; and (3) only higher prices can overcome these deficiencies, as this would provide sufficient inducement for the industry to explore for and develop new reserves and productive capacity.

Jan 1, 1967

Exploration for SX-EW copper deposits and plant operation depend largely on the copper and gangue mineralogy inasmuch as? they govern the feasibility of leaching. Mineralogical parameters are pivotal in identifying if an ore is suitable to dump, heap, thin layer, vat or agitated leaching and/or if the ore requires curing, bioleaching or alternate lixiviants. Problems in metallurgical testing, production leaching and recovery forecasting are very often related to lack of mineralogical data. This presentation will illustrate the use of quantitative mineralogical analysis for exploration, acquisition assessment and optimization of copper leach operations.

Jan 1, 1996

By Jewel A. Gomes

Keywords: Electrocoagulation, arsenic removal, fuel cell, windmill, energy simulation, combined Fe-Al electrode assembly Arsenic contamination of well-water in different countries has caused signs and symptoms of arsenic poisoning. Although several physicochemical treatments are presently used for the removal of arsenic compounds from drinking water, an electrochemical treatment, electrocoagulation, is a promising processing technology and currently is the most efficient (above 99% removal) and environmentally friendly technique, particularly if combined with alternative energy sources. Wind and fuel cell technologies can be considered the most promising developmental clean power sources. We will discuss new insights into the materials processing mechanisms and show the coupling of electrocoagulation with fuel cells and simulated wind energy sources. Different electrocoagulation plate materials were considered, along varied currents from the fuel cell to produce maximum arsenic removal. Coupling these technologies will remove carcinogenic arsenic from water sources, and will exhibit efficient usage of these energy sources by producing pure water for human and agricultural consumption.

Jan 1, 2005