Search Documents

By Brinton C. Brown

This paper describes the methods and equipment developed at the Bureau's Experimental Oil-Shale mine near Rifle, Colo., for placing men in position to scale loose rock from the walls, pillars, and roofs of high stopes or rooms. The equipment developed at Rifle has application not only in oil-shale mining but in most of the country's underground limestone mines and in the exploitation of other mineral deposits mined in high stopes by room-and-pillar methods. Equipment in use at Rifle includes: 1. A boom-type scaling rig with a self-leveling platform constructed on a small "cat"-mounted crane. Men working from the platform on this machine can efficiently scale mine walls and roofs 27 feet above the floor. 2. A conventional fork-lift truck modified to provide a remotely controlled working platform from which men can scale to heights 27 feet above the mine floor. The platform on this unit is larger than on the boom-type rig and allows the men to inspect larger areas of the mine wall from a single setting of the machine. 3. A third rig, consisting essentially of a platform mounted on a tele-scoping tower, designed and built to elevate men 65 feet above the mine floor. Versatility of this machine permits men to work from the platform at heights of 5 to 65 feet. In the operating position, the unit requires a minimum clearance of 25 feet. In the nonoperating position the tower of the machine folds to an over-all height of 15 feet 10 inches to permit travel through haulageways. 4. An industrial gun, lightweight scaling bars, and mechanical scalers, which have been tried for removing loose rock from the mine walls with varying degrees of success.

Jan 1, 1950

By Walter W. Kaufman

The braking performance of underground, rubber-tired, non-coal mining vehicles is evaluated. Surveys of mining equipment and braking manufacturers and underground stopping tests are discussed as they relate to this evaluation. Stopping performance recommendations are included as well as related aspects of roadway construction and runaway vehicle protective devices.

Jan 1, 1977

By R Jacobs, J Yeates

"The Stockman base metals project is situated in State Forest in the alpine area of East Gippsland, Victoria, adjacent to a National Park and within the headwaters of a major Ramsar-listed wetland catchment and the Murray-Darling River system. Site topography is steep, and elevated (650 m – 1200 m above sea level), and subject to circa 1 m annual rainfall, with occasional winter snowfall. The project consists of two volcanogenic massive sulfide (VMS) deposits to be mined by underground methods and treated in a 1.0 Mt/a central concentrator to produce copper and zinc concentrates for export over a ten year operational life. New resource projects are rare in Victoria. Recognising the sensitive setting, planning for the Stockman Project, which is now in the advanced permitting stage, has focused on balancing economic, environmental and social outcomes to ensure social licence to operate is secured and can be maintained. This has involved close attention to triple bottom line (TBL) risks and outcomes. Stockman has successfully gained State and Federal approvals via the Environmental Effects Statement process. The process of obtaining these approvals has required close attention to effective stakeholder involvement, and management of a lengthy and difficult approvals process, which is still to be finally concluded. This paper is a case study of the process of that permitting and the issues encountered to date. Key learnings from the experience have included: successful approvals require close attention to much more than just the project and its technical aspects and physical setting – effective stakeholder involvement and endorsement is critical the differing consultation requirements for local, regional and government stakeholders, to design and plan implementation of a project to meet TBL objectives, and to gain social licence to operate within the Victorian approvals process, the need for an effective lead government agency with policy authority dealing with material policy change requiring post-closure financial sureties estimating realistic permitting time and cost during the project evaluation phase. CITATION: Jacobs, R and Yeates, J, 2016. Stockman base metals project – sustainability, social licence to operate and permitting lessons learnt, in Proceedings Project Evaluation 2016, pp 98–110 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By R. L. Summers

The tremendous engineering advances occurring during this past century are very evident within the boundaries of the Anthracite Section of AIME. The Steelton plant of Bethlehem Steel Corporation, located along the Susquehanna River just east of the Commonwealth's capital at Harrisburg, for more than 105 years has experienced a most dynamic life which has paralleled America's industrial growth. (Figure 1) In June 1865, just after the Civil War, a group of men met to organize the Pennsylvania Steel Company. The war had brought into sharp focus the vital importance of the railroads to the country's expansion. Until that time wrought iron rails were used, and the replacing of track after only several months wear had become an almost unbearable cost. The spirit of free, competitive enterprise and the prospects of a lucrative market compelled these men to form that first Pennsylvania Steel Company and to develop better rail products. They issued the following statement: "...our desire to free ourselves from dependence upon a foreign market (has) led to the organization of the Pennsylvania Steel Company, and the parties who have connected themselves with it are determined to produce upon American soil all the principal manufactures of steel that are now, at such a serious cost for freight, commission, insurance, exchange, duty, etc., and often, with so much delay and uncertainty, imported from abroad. (We) are preparing to establish near the consumer, works at which articles of accustomed pattern will be promptly produced, and from the

Jan 1, 1971

By J Jackson

The term geometallurgy (or geometallurgical) first appeared in the literature some 40 years ago and has a wide range of definitions and perspectives which increases the barriers of communication between practitioners and across functional groups and management levels within organisations. However the consistent theme running through the diversity of definitions and perspectives is the requirement for close collaboration between the relevant disciplines. This concept of geometallurgy arguably goes back to the earliest days of the exploitation of mineral deposits, through the mid-1500s to the beginning of the 20th century.This holistic and integrated view was diminished during the 20th century due to a number of factors which included the commencement and continuing upward trend of large-scale mining and the expansion in production, the rise of scientific and classical management theories and methodologies, increase in specialisation and the development of traditional project planning. The re-emergence of geometallurgy in the late 20th century required the relevant functional units and disciplines to collaborate as a team. This necessitates a common understanding that the geometallurgical program’s goals must be obtained, which requires clear and consistent communication, particularly with the modern trend of virtual teams.A multi-dimensional construct is proposed to assist in providing a consistent approach in the communication of the context and purpose of both general and specific geometallurgical programs, thus simplifying communication. This geometallurgical construct consists of the dimensions of process span, response knowledge, variability knowledge, spatial knowledge, application and project phase in relation to extraction process(es) applied to geological materials from a mineral deposit. These dimensions are then linked to the phase of mineral project development in which the geometallurgical program is being applied, which ranges from advanced exploration through to operational execution. This paper outlines the multi-dimensional construct with examples of how the context, purpose and scope of geometallurgical programs can be clearly delineated and communicated.

Sep 5, 2011

By Luana Ferreira de Carvalho, Aurelio Manço Garcia, Gustavo Sampaio Lopes, Jose Silvio Corsini, Davi Bastos Martins de Oliveira

The Enaex Mining Technical Solutions (EMTS) team, in partnership with the Anglo American Iron Ore Brazil drilling and blasting team, has developed a study aiming to optimize the blast design applied at the Minas-Rio project. The study consists of modeling the dynamic behavior of one lithological domain to determine the best configuration of drilling pattern, charge configuration, timing and sequencing of the blast designs applied at the mine in this particular rock.

Feb 1, 2020

By Thomas C. Ruhe

The Bureau of Mines conducted research to determine the safe operating conditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) saves energy, reduces oil imports, and reduces mining costs. Low ambient temperatures may cause these recycled oils to become too viscous for proper absorption by ammonium nitrate (AN) prills and result in poor blast performance, safety hazards, and environmental problems. To help quantify and resolve these issues, viscosity, mixing, and performance tests were conducted at various temperatures. Diesel fuels No. 1 and No. 2 were studied separately and in blends with 25,50, and 75% RO. Good quality ANFO mixes (94-6) were produced with dry absorbent prills and blended fuel (No. 1 diesel plus RO) at temperatures as low as -40°F (-40°C) with 75% No. 1/25% RO, and at -20°F (-29°C) with 50/50. Diesel fuel No. 2 also made good mixes as low as -30" F (-34°C) with 75% No. 2/25% RO, and at 0°F (-18°C) with 50/50.

Jan 1, 2008

By James D. Cooper

Technologic advances in materials utilization during the past two decades have brought is a long way toward the point where we can make the products we need from the materials we have readily available. Notable examples are the synthesis of diamond, zeolites, quartz crystal, mullite, and mica, and the development of phosphate bonded tale. Two of these--zeolites and mullite--involve the use of clays. There is little reason to doubt that equally important advances will be realized in the next decade, and that clays will play an important role in the developing materials technology. Indeed, the stage is already set for many of them. This discussion is concerned primarily with the high quality, relatively high priced clays, kaolin, bentonite, fuller's earth and ball clay. The first three have enjoyed demand growth rates over the past two decades which on the average exceeded the growth rate for the economy as a whole. There are indications that demand for ball clay will be growing at a faster rate in the future.

Jan 1, 1970

By D. Harrington

"While distribution of air currents to working faces is a necessity in coal mines, especially those having explosive gas, advancing faces in metal mines rarely have circulating air other than the ordinarily inadequate amount supplied through the compressed air system. Even where comparatively large quantities of air pass through main mine shafts and levels. whether the circulation is actuated by fans or by natural ventilation, only occasionally can a metal mine be found where any considerable percentage of the ""blind ends"" has circulating air of sufficient velocity to be measured by an anemometer or even be discerned by deflection of flame of candle, or of acetylene lamp; and unfortunately these ""blind ends"" include nearly all of the places from which rock is taken.During several years study of metal-mine ventilation in various mining districts of the United States, it has been found that in some mines many of the workers in ""blind ends"" practically continually breathe air with 0.02 to 0.04 per cent of CO gas from unremoved fumes from explosives; in other mines CO2 chiefly from timber decay and breathing of men, is so high that a candle will not burn though usually the acetylene lamp will, hence oxygen is below 17 per cent but above 12 per cent; in some regions CO2 from strata fills the entire mine forcing cessation of work; in other mines in dead ends, gases such as nitrogen, H2S, SO2, etc., are found under some conditions. In many regions with hot rock or water (especially in deep workings) men in blind ends must work with little or no circulation, in air above SO degrees F. and even above 90 degrees, relative humidity only too frequently being around 100 per cent; in other regions workers in blind ends in practically ""dead"" air must continually breathe enormous quantities of finely divided rock dusts. All of the above conditions are decidedly harmful to health and prevent the worker from delivering anything approaching an adequate quantity of work, and in addition, some of these conditions have direct or indirect effect in bringing about definite increase of accidents; all of the above mentioned bad conditions in ""blind ends"" in metal mines as well as their ill effects, are remediable by providing at those places adequate quantities of fresh circulating air."

Nov 1, 1923

By Sheng Dai, Yuan Lee, Haiming Xiao, J. P. Young

"There are numerous analytical applications of scatter-emission and/or absorption spectroscopy applied to liquids and solids in the temperature range of 0 to 350°C. In this paper an all-silica fiberoptic probe is described which is useful for spectral analyses from 0 to 1600 K and can be used in harsh chemical environments. The probe has been used for Raman spectral analyses of many molten salt and solid material systems to 1000°C. It has applications for such studies at higher temperature ranges. The instrumentation required along with the demonstrated and proposed applications of the all-silica probe are presented and discussed.IntroductionThere are many kinds of scatter-emission spectroscopies that are of value for analytical measurements. Fluorescence, reflectance, arc or spark emission are descriptors for some of these. Raman scatter spectroscopy is also quite a useful technique for analytical measurements.In Figure 1, we give a simplified explanation of the Raman effect. If one shines monochromatic light into a sample, light may be absorbed, exciting the sample to some virtual state. We know from experience that almost all of the light is re-emitted in the same wavelength range. This is called Rayleigh or Mei scattering and is designated in the figure by the arrows in both examples that point up and down from the same lower energy state. A very small percentage (the order of 10-4%) of the monochromatic light is re-emitted leaving the sample at a vibrationally-excited state. Thus, this light is at a distinctly lower energy compared to the exciting radiation. This is called a Stokes shift and is represented in the left-hand example by an arrow descending to a more energetic vibrational state. If the sample is not at a temperature of absolute zero, some of this vibrationally excited state will be thermally populated. That portion of the sample still absorbs and re-emits exciting radiation as Rayleigh scattered light, but a small percentage of the exciting light is re-emitted as the sample relaxes to the lower vibrational state. The energy of this light is of higher energy and is called an anti-Stokes shift, depicted in the example to the right. Notice that the energy separation of the Stokes or anti-Stokes shifted emission from that of the exciting radiation is the same, and expressed in ~cm-I. The intensity of either shifted emission is a function of the population of the vibrational energy states; therefore, the ratio of the intensity of Stokes to anti-Stokes signal varies with absolute temperature. We will come back to this point later."

Jan 1, 1997

By Andrew Baxter

The Crystal Bridges Museum of American Art in Bentonville, Arkansas is a beautiful glass and concrete structure cut into a valley that mingles with water ponds spanned by multiple bridges with suspended roofs. Or, at least it will be when completed in 2009. At Crystal Bridges, most of the proposed buildings involve cuts up to 50 ft high to be retained by the building structures. This requires the construction of retaining walls adequately founded to support lateral loads of up to 70 kip/ft. To add to this difficulty, the site is within a karst region with all the variability and irregularities associated with solutioning and erosion of the parent rock in this environment. The irregular rock profile made it virtually impossible to conceive a predictable arrangement of shallow footings and shear keys for the retaining walls. The existence of layers of soft soils within a hard rock formation made a caisson foundation impractical. The authors developed an innovative solution based on micropiles, which proved to be invaluable from a cost and schedule point of view. In areas where rock was shallow, micropiles were used as ?shear pins? to transfer the horizontal loads to the rock. In areas with significant overburden, a system of vertical and battered micropiles was devised to carry vertical and horizontal loads from the retaining walls. This paper presents a detailed description of the design and installation of the micropiles used as shear pins, and includes the results of lateral load tests performed on full-scale models of the grade beams on shear pins. The work performed shows that micropiles in rock can be effectively utilized for support of significant lateral loads provided that an adequate arrangement of suitably sized micropiles is provided, and that micropiles used as shear pins may develop significant tensile stresses when loaded laterally.

Jan 1, 2008

By Eugie Kabwe

Rock bolts are components of tunnel support structures and their efficacy in reinforcement requires the appropriate estimation of the bolt pre-tension. However, cases of ineffective rock bolt application due to loosening are common which leads to the potential failure of the support structures, thus negatively affecting the tunnel stability. The effective employment of pre-tensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut pre-load. Henceforth, this paper presents a load indicator washer (LIW) capable of withstanding assigned static loading as well as provides an appropriate pre-tension. The different LIW breadths are numerically analysed in the finite element code (ABAQUS) to estimate deformation when a designated 60-kN pre-load is applied. The numerical simulation employs a bi-linear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nutLIW-rock bolt connection. Therefore, a long-term relaxation effect on bolt pre-tension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW-predetermined deformation is the bolt pre-tension. It is drawn from the simulation results that the 1.5-, 2.0-, 3.0-, 3.5-, and 4.0-mm-thick LIWs are completely flattened when subjected to 28-, 42.5-, 65-, 76-, and 88-kN pre-load respectively.

By D. C. Lynch

While silica ores are generally considered to have little value, those with exceptionally low B and P content have, potentially, significant worth if processed for use in photovoltaics. The sales value of a cubic meter of ?run of the mill? silica sand is $42 per cubic meter (retail and delivered). If the silica sand can be used to produce solar silicon, its value after processing is $34,000 per cubic meter. Factors that impact the suitability of silica for direct processing in production of photovoltaics are examined.

Jan 1, 2010

By B Wong, R G. Coleman

In flotation, the selection of the size, number and type of cell for a particular duty depends on two important factors. Firstly, the required flotation residence time and secondly, the physical constraints of how much concentrate can be recovered for a given froth surface area and concentrate lip length. The residence time is influenced by ore type and characteristics such as liberation, kinetics and reagent dosage. The amount of concentrate that can be recovered for a given froth surface area and lip length depends on ore type and other characteristics such as particle size, specific gravity and mineral grade. Residence time is determined through a combination of laboratory-scale test work and design scale-up factors. However the critical froth transport parameters such as froth carry rate and froth lip loading cannot be determined in a laboratory. This is because the froth is scraped during a laboratory flotation test and thus does not exhibit natural behaviour, and it is not possible to scale-up froth transport distance or air rate. These values are generally compared via calculation to rule-of-thumb maximum values to establish if these values will be exceeded by the flotation cell selection.This paper first reviews these critical froth transport parameters and then discusses actual parameter values across diverse operating sites, with varying cell duties, cell sizes and types, orebodies and particle sizes. These values are compared against the industry rule-of-thumb to test the applicability of the rule-of-thumb to actual performance. Options are also presented for adjusting these parameters in operating flotation cells.CITATION:Coleman, R G and Wong, B, 2018. Flotation launder design and the measurement of critical froth transport parameters, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 353–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By D Ford

BHP BillitonÆs new rotary iron ore car dumper installation at Finucane Island (Port Hedland) was constructed to increase the total capacity of the port facility from 110 Mtpa to 120 Mtpa and to allow for incremental capacity increases in future. The arrangement of the dumper is similar to other car dumper installations existing on site. To construct the facility, approximately 120 000 m3 of material was excavated in six months, to a total depth of 22 m. The saline water table was nominally 6 m below ground level and the materials excavated varied depending on depth, ranging from sand to mangrove muds. There was a need to retain the sides of the excavation and limit the amount of water from entering the excavated area. This was required to allow excavation to progress and had to be maintained during construction of the permanent concrete and steel facility. The excavation was backfilled progressively as construction progressed. Various retaining wall methods were investigated with the preferred option being sheet piles secured by walers and ground anchors. Detailed electronic models were developed and assessed to complete the final design arrangement. Dewatering bores around the perimeter of the excavation removed the groundwater to intercepted sumps within the site. A strict and methodical program was developed to monitor the integrity of the temporary works and the quality of the groundwater. The works were completed on time despite the following challenges being encountered: availability of resources and equipment, movement of mobile plant on æboggyÆ materials, difficulty driving sheet piles into material at depth, drilling of ground anchors to 32 m, grouting of ground anchors, greater than expected groundwater flows, and the risk of hydrocarbons within the groundwater. The lessons learned from the use of the retention system and, in particular, the associated construction challenges overcome, provide a sound basis for similar work in this buoyant resource market. The conference paper describes the temporary works options investigated, design considerations and processes, construction methodology and challenges encountered, and the monitoring systems developed. Lessons learned are also discussed.

Jan 1, 2007

By R. F. Coulter

THE Flin Flon concentrating and metallurgical plants (Figure 1) of the Hudson Bay Mining and Smelting Co., Limited, lie adjacent to the town of Flin Flon, on the Manitoba-Saskatchewan border, 400 miles northwest of Winnipeg. Since the start of milling operations in 1930, over 50 million tons of ore from the Flin Flon mine have been treated in the concentrator. During the past few years, newly discovered orebodies have been brought into production and their ores processed at the company's main metallurgical plants. All these properties are within a 75-mile radius of Flin Flon and have aided substantially in augmenting plant metal production as well as retarding depletion of ore reserves in the Flin Flon mine. •Current satellite producers are the Schist Lake, Coronation, and Chisel Lake mines. The Schist Lake mine, located 3 ½ miles southeast of the main plant, is a copper-zinc producer. It was brought into production in 1954. The

Jan 1, 1962

This publication summarizes, for all interested parties, the research, development, and demonstration in-house projets programed by the Bureau of Mines for fiscal year 1980 (October 1, 1979 - September 30, 1980) under its Minerals Health and Safety Research program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1980

By F. C. Smyers, E. W. Merrick

ALTHOUGH the zinc and pyrite concentrates produced at Midvale go to other companies, the United States Smelting Refining and Mining Company smelts and refines its own lead. Refining is the first step of the process that is done at some distance from the mining operations, the plant being at East Chicago, Ind., an industrial center about 25 miles southeast of Chicago. For years it has been notable as being the only lead refinery in the country using the Betts electrolytic process. The original buildings, many of which are still in use, were erected in 1906 when the plant was known as the United States Metals Refining Co. In 1920 the parent company sold its copper refinery at Chrome, N. J., and since the copper refinery was also known as the U. S.

Jan 1, 1948

By T Elms, R Beckman, M Sampson

"In today’s mining industry, the pressure of reducing costs and increasing production while maintaining high safety standards is at the forefront of operational endeavours. A combination of specific mining knowledge and technological advances has helped enable this notion. Fleet management systems have been developed to enable sites to better measure and manage production to improve operational efficiency.The integral part to managing production is having accurate, readily accessible data. This empowers key stakeholders in the management team to drive production reporting, materials tracking and budget forecasting.If a site does not run a fleet management system, manual input is heavily relied upon for production data, which introduces increased risk of human input error. Errors can drive outcomes that don’t achieve increased production at a reduced cost. Alternatively, a fleet management system can have improved accuracy but involves a high monetary investment. Such an investment is not always feasible for smaller mining operations subject to current industry cost pressures.The Emeco Operating System has been developed in alliance with sites such as the Mungari White Foil Operations by satisfying the criteria of a low intensity hardware installation, material tracking data validation processes, remote monitoring, identification of metrics to improve overall operating efficiency and providing the right information to key stakeholders.Citation:Beckman, R, Elms, T and Sampson, M, 2016. Getting Accurate Mine Information to the Right Teams to Drive Production Improvement, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 203–211 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Christopher Laughton

A new underground laboratory is under construction at the recently closed Homestake Gold Mine, Lead South Dakota, United States of America. The Deep Underground Science and Engineering Laboratory is designed to meet the needs of an international group of scientists and engineers interested in conducting fundamental and applied research at depth in the Earth’s crust.

Jan 1, 2011