Search Documents

By Timothy Batchler, Khaled Mohamed

Standing supports have been used in coal mines for decades to enhance roof support capability. Occasionally, standing supports are used to resist the lateral movement of spalled ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting a testing program for standing supports to investigate the effect of lateral loading on their vertical loading capacities and the factors affecting their lateral loading capacities. The Mine Roof Simulator (MRS) was used to determine the response of steel props to vertical and horizontal loadings. Finite element models (FEMs) were developed and verified using the tested steel props. Prop models were used to study the effect of a range of roof and floor materials — gray shale, shale and claystone — on the critical buckling loads of the steel props.

Dec 1, 2022

By Ekin Güngor, Berkant Ozdemir, Erkan Bayrak, Serdar Ergün, Sedat Esen

"This paper presents the final wall blasting practices at Eldorado Kisladag Gold Mine in Turkey. Benchmark and improved wall control designs were explained in detail. Kisladag Mine has been implementing a high quality slope stability program on-site. The quality of pit walls is generally considered excellent, with very few wall failures being evident and with presplit hole barrels prominent in most areas of the pit. However, a minor scale slope failure occurred recently at the north-east section the pit. A project was initiated to diagnose the cause of the crest loss and evaluate ways to limit its effect on final walls. Final wall blasting practices and geotechnical designs were evaluated. The work presented in this paper showed that changes to the blasting and geotechnical parameters are required atthe north-east section of the pit. Geotechnical design changes were 10 m bench heights with 70 ° slope face angle at that specific area. Having implemented several geotechnical and blast design changes (elimination of the subdrill for the catch bench, appropriate primer location, more favorable blast tie-up and delays), the crest loss was minimized significantly (<1.5 m) (<5 ft)."

Jan 1, 2017

By S. M. Shelton

Preliminary work in the investigation of electrolytic manganese, as reported J, showed promise for a practical procedure of continuous production. Laboratory work was continued in the direction of process simplification to determine an economically feasible procedure that mould require a minimum of expensive equipment for plant erection and a minimum of regent consumption for operation. Results furnished enough evidence to indicate that modifications of the process could be made leading to simplified procedure and with no sacrifice in operating efficiency. A supply of at least 200 pounds of the metal was desired for alloy research, and it was believed worth Mile to utilize available facilities in a search for difficulties, that were not encountered in the laboratory and that might arise in larger-scale operation. Consequently, an experimental pilot plant was erected. The plant was designed for a capacity of 15 rounds per day of metal and operated under simulated -plant practice.

Jan 1, 1938

By Tao Zhang, Wen-tao YU, Hai-bin ZUO, Jian-Liang Zhang

Sintering-pot tests and metallurgical performances of sinter with 4 kind of different Al2O3 contents are experimented in this paper. Results show: when the Al2O3 contents increase from 2.0% to 3.5%, acicular calcium ferrites in mine phase will be gradually replaced by plate-like iron calcium. The increase of Al2O3 contents will lead to the addition of liquid viscosity and the reduction of permeability of sinter bed. Sintering time will be prolonged. The rate of yield is stable basically but production is low; besides, the increase of liquid viscosity will decrease of drum strength. The change of permeability of the material layer will make RDI +3.15 decrease first and then increase when Al2O3 contents changed from 2.0% to 3.5%. RI of sinter shows a contrary trend because many open voids are formed by deterioration of liquidity first and then pores closed.

Jan 1, 2015

By Walter E. Lewis

A mothod of cutting St. Poter sandstono by streams of water under pressuro from nozzles and pumping the resulting, sand to the surface has roduced the cost of storm-sowor construction in the Minneapolis-St. Paul aroa. The hydraulic tunneling method, has boon in uso since 1934, and it is adaptable only to the lower part of tho St. Potor, sandstone, which lios within or just abovo the ground-wator levol. Tho upper part of the formation, immediately bolow tho Plattoville limestone, 18 comonted and camot bo mined by hydraulic mothods. The tunnel oporation observed in this instance is a main storm sowor starting at tho Mississippi Rivor below the 10th Avenuo SE bridge and will be drivon 6,000 foot at a grado of 1 foot por thousand undor the city of Minneapolis to Konnody and Arthur Stroots NE. A lateral storm sowor, which branchos from the main sovor at 8th Street SE, will oxtond from 10th Avonuo SE to 15th Avonuc SE. Tho tunnele are being drivon with the floor approximately at ground-wator lovol. All waters ontoring the main storm sower vill drain into the Mississippi Rivor. Tho main storm sewer cross soction is excavated to a roughly hox- agonal shapo 10 foot high by 10 foot wido at the contor. The upper half of the tunnol soction is solidly lined with either timber or stool. After all oxcavation is completed, the tunnel will be finished with a concrete circular lining 8 feet in inside diameter. The lateral storm sewer is excavated to a 5-1/2-foot by 7-1/2-foot section and will event- ually be finished with concrete to a modified horseshoe-shaped section 6 feet by 4 feet. Where the back or walls are considered unsafe during excavation, the upper half of the tunnel is lined solidly with timber. The equipment used by the Sower Division, City of Minneapolis, has been selected to meet a number of applications in storm-sewer work with diversified usage in mind. The sand pumps used on this job are rubber-lined, designed to work against a head of 100 foet. Either 4-inch or 6-inch diameter suction and discharge openings may be used. Other equipment, such as pipe, mine rail, flexible hoses, compressors, and general surface shop equipment, is drawn from a contral warohouse. It may be either new or used, depending on what is available at the warehouse. Much of the pipe and mine rail has been used for many years on several different tunnol jobs.

Jul 1, 1950

By V. Ushakov, P. Bogdan

Daily production scheduling in a highly dynamic smelter environment has always been a great challenge for the operation management due to a significant amount of uncertainties. Planned and unexpected equipment failures, various energy outages, inaccuracies in flow and mass balancing, manpower availability conflicts and other constraints make the job of daily production planning exceptionally difficult. This paper discusses a general scheduling approach utilized by the production management of the Phelps Dodge Miami Smelter (the Smelter). It also describes logical assumptions and some practical software solutions that have been exploited by the Smelter managers to assist the front line supervisors in dealing with daily planning activities for several years.

Jan 1, 2007

By Q. G. Reynolds

The presence of dust and fume suspended in the freeboard region is a common feature of the operation of direct current (DC) plasma smelting furnaces. This occurs primarily as a result of the use of fine feed materials together with the open-arc, open-bath operation of such smelters, and is exacerbated by the high velocities and turbulent mixing of the gas in the vicinity of the arc jet. Dust and fume losses into the furnace off-gas system can be significant in some cases and may have economic, operational, and environmental impacts on the process. A computational modelling study is presented in which the concentration of dust material was considered as a continuous field subject to a governing partial differential equation. Settling behaviour was calculated as a function of particle size, local gas/plasma temperature, and other physical properties. Development of the coupling between the concentration field and a magneto-hydrodynamic description of the arc is shown, and the resulting models were used to compute various aspects of the behaviour of the concentration field in the arc region for a variety of furnace conditions. Time-averaged as well as transient models of the arc were used to generate the results presented. Qualitative case studies produced several practical suggestions for furnace operation, including increased dust capture by the bath when feed ports are located closer to the electrode, and the possible effects of feed segregation in the furnace freeboard based on dust particle size and density.

Jan 1, 2014

By Harry J. Fitzgerald

During World War II mining machinery manufacturers were limited in the development of their product improvement programs. Following the war, however, the ideas and intentions of both the users and manufacturers of mining equipment became evident. The Coal Industry launched a series of events which indicated their determination to rise to the economic challenge of developing profitable machines which would eliminate the out-dated and back-breaking methods of mining previously used. Two major technological advances were developed as a result of the ambitious goals forecast by the Coal Industry: 1. Coal mining was going "off-track" and concentrated mining operations were to follow in rapid succession. 2. Carbide tools provided the remaining missing contribution to another technological breakthrough....Continuous Mining. Little did the inventors realize the significance of the misnomer they created because twenty-five years later the industry is still striving to secure the results implied by the meaning of the word...."Continuous". Nevertheless, all major manufacturers embarked on programs in an attempt to compete for recognition in this new mechanized-mining endeavor Eventually in 1950 there were three types of boring machines and two types of ripping machines being manufactured. Mining Speed was the desired goal.

Jan 1, 1970

By Peter A. Amelunxen, Richard LaDouceur, Courtney A. Young

"Many of the rare earth elements, the lanthanide series on the periodic table, are on the U.S. Department of Defense Strategic and Critical Materials list. In this regard, the U.S. Army Research Laboratory (ARL) has funded several projects at Montana Tech focusing on rare earth element recovery from natural resources. Current froth flotation operations utilize octyl hydroxamate for rare earth mineral extraction, however recovery is not ideal and flotation performance can be improved. Salicylhydroxamic acid (C7H7NO3) was identified as a novel collector due to similarities with n-octyl hydroxamate, notably the amine head group. Salicylhydroxamic acid is primarily used in the medical industry but due to the amine head group is ideally suited as a collector for rare earth mineral flotation.Parametric studies were performed for the flotation of rare earth minerals by modifying a wide range of variables. Mechanical variables of a 6L bench scale flotation cell, such as air inlet flow, rotor speed, and milling time for liberation were modified to elucidate energy input parameters for the desired minerals. Chemical parameters such as collector concentration and pH were varied to understand solution chemistry considerations of the salicylhydroxamic-rare earth mineral system. The study obtained a statistically significant experimental model for the flotation of rare earth minerals. A two stage compartmental model was also utilized for the determination of the first order flotation rate constants for each mineral. Optimized recovery of rare earth minerals was found to occur at near neutral pH ranges using salicylhydroxamic acid with maximum recoveries approaching ideal industrial standards although rare earth mineral grades were still not sufficient.INTRODUCTIONRare earth elements (REEs) are found in minerals that contain several REE which makes costeffective separation of the rare earths difficult. Significant scientific challenges have hindered mineral separation. The molecular similarity of rare earth elements results in minerals containing several REEs, such as bastnaesite [(Ce, La) CO3F]. This prevents efficient separation during concentration steps, for instance flotation, and has a direct impact on successive metallurgical processes. Consequently, concentration during flotation is of rare earth minerals (REM) as opposed to REE."

Jan 1, 2016

By Clayton A. Landsidle

There has been little change in timbering methods in anthracite mines for 75 years, and technical information on strata control is almost wholly lacking. In order to assist the industry to establish technical data, the Bureau of Mines and a Northern field operator are cooperating in underground experiments, the first phase of which has been to investigate pneumatic packing. The four principal methods of packing in mining are hydraulic, pneumatic, mechanical, and hand. The hydraulic pa caring system is believed to have originated at Shenanodah, Pa., in 1864,4/ to prevent destruction of a church by surface subsidence after underground coal mining. This method was used again in 1884 to arrest an underground fire at Buck Ridge colliery, near Shamokin, Pa. In 1901 hydraulic packing was introduced to Europe in Upper Silesia, where it gained in popularity owing to the availability of large quantities of sand suitable for flushing .5/ Hydraulic packing has a number of disadvantages. Chief among these are the softening effect of large quantities of water on the mine floor conducive to heaving action; drainage and punning costs; and the inability to fill roof cavities completely in flat beds.

Jan 1, 1953

By Strathmore R. B. Cooke

That calcium will activate quartz for flotation with anionic collectors such as soaps has been known for a number of years,1 2 3 and the method has been applied to the concentration of various iron ore 4 5 6 as well as to other materials. Clemmer gives the permissible pH range for the activation of quartz by calcium as between 9.5 and 12.5 with an optimum value of 11.0, and Hertzog7 has determined the calcium abstraction of iron ores and of Ottawa sand, but otherwise little quantitative data are available. The purpose of the present investigation was to determine those conditions under which dilute solutions of calcium chloride will activate quartz for anionic flotation and to determine the amount of calcium ion adsorbed by quartz. Those variables, the influence of which was primary, such as calcium, sodium, and hydrogen ion concentrations, were studied. Other factors which influenced the results are discussed in the description of the experiments. Three different experimental methods were used to determine the activation of the quartz. The first method was to treat a sample of ground, deslimed quartz with solutions of calcium chloride and sodium hydroxide, and to determine the calcium adsorbed by chemical analysis of the solution. Ad- vantages are that a direct value for the

Jan 1, 1949

By M. Cavallini, G. Cannavale, P. P. Milella, A. Pescetelli, C. Lupi

Ni-Cd sealed and vented cells have been widely used in the last few years. The environmental hazard related to the heavy metals contained in Ni-Cd batteries is well known. Therefore, a number of scientific studies and commercial processes have been implemented in order to recycle them. Since spent batteries are a heterogeneous and complex material, any kind of recovery process needs some preliminary treatments. The proposed process described in this paper has been tested in laboratory and further developed in a pilot plant. It consists of a combination of mechanical and hydrometallurgical treatment steps, and is able to treat all type of Ni-Cd batteries. In particular, the mechanical treatments have to be done separately on vented and sealed cells, while the hydrometallurgical step is performed on a mixture of the two products obtained from mechanical steps. A fully automated dismantling line would allow the separate recovery of the plastic or metallic casing, terminals, KOH electrolyte, and electrodes to be further processed· for Ni and Cd recovery. The electrodes coming from dismantling line and sealed batteries are submitted separately to an original crushing and elutriation treatment to separate metallic and active paste in the first case and metallic, plastic and active paste in the second case. The hydrometallurgical treatment is carried out on active paste bearing product to produce Ni, Cd, and Fe comn1ercial salts through acidic leaching followed by a multi-step solvent extraction operation to obtain pure solutions.

Jan 1, 2000

By Billy W. Parks

This paper reports on the first 2 years in operation of a special-purpose coal handling rig which provides blending, temperature reduction, and continuous, automatic mechanical sampling as part of midstream barge to ship coal transfers. Briefly reviewing some of the characteristics of coal handling peculiar to midstream transfers, the paper discusses how the most beneficial aspects of midstreaming were enhanced through the design of this blending and sampling rig.

Jan 1, 1986

By B. R. Rakishev

When transferring from the railway transport to the combined automobile-conveyor transport by stripping works at coal mines, it was proposed to form at the working zone a concentration horizon for reloading part of the stripping volumes at the railway transport. The procedure is adduced for substantiating parameters of bloc-panels, depending on the step of transferring of reloading points in interrelation with the intensity of the working zone?s development with observing the balanced movement of parts of the stripping zone relative to the temporary concentration level.

Aug 1, 2013

By I. D. Ustinov, V. A. Arsentyev, A. O. Mezenin, A. M. Gerasimov

"The solid mineral raw materials of the sediment deposits containing the argillaceous variations such as the coal and the potash ores are the most multi-tonnage solid minerals mined and processed in the territory of the Russian Federation. Both types of the deposits have relatively simple geology aspects with large and medium-sized solids and as a rule, the most often, with the regular bedding which are characterized by the fitchery thickness and the internal structure. Such deposits are very difficult for mining and processing. The thermal modification of this of ores allows changing the physico-chemical properties of its components in such a way that their further processing - grinding, separation, transportation and storage can be carried out without the use of process water or significantly reduces its consumption. The purpose of the present study is to increase the efficiency of the mineral processing containing the layered aluminum silicate by reducing their negative impact on the basic dressing processes, the separation of suspended matters and the storage of waste. INTRODUCTION Many deposits of minerals are associated with the presence of layered silicates such as the argil, mudstones, argillaceous slate - highly hydrophilic mineral varieties which have the ability to swell in the water. This ability to self-disperse creates the great difficulties both for the extraction and the processing of such ores. Since the dressing of most minerals is associated with the use of wet processes, where in contact with water the swelling layered silicates are dispersed to a particle size of less than 50 µm, but due to their high hydrophylic property they form bonds that promote the formation of so-called structured suspensions having increased viscosity. In this case the structured suspensions make it difficult to perform the separation operations as the classification, the gravity and magnetic separation, the flotation and thickening and filtration operations."

Jan 1, 2018

By Alvaro Diaz

Introduction, who is Teck Red Dog and Quebrada Blanca Mines Uniqueness of environment Arctic versus High Altitude Conditions Logistical challenges People and Stakeholders Conclusions

May 1, 2013

By R. V. Ramani

"A computer simulation model of a dragline has beer developed for the study of alternative dragline deployment schemes for varying geological and mining conditions. In this paper, the mathematical aspects of the model, the input data and output results are discussed. An application of the model to a coal mine in eastern Kentucky is presented.IntroductionDraglines are very productive machines. To extend their operating ranges, they are operated in several modes such as advance benching, key cut, extended benching and pullback. Unfortunately, these variations result in low machine productivities. Appropriate methods to operate these machines must be developed on the basis of detailed analyses of dragline performance under varying geological and mining conditions. There are several standard engineering procedures for the selection of dragline, and design of a dragline pit (Ramani, Iroegbu and Manula, 1976). However, the complex interrelationship which exists among equipment, methods and natural conditions can be quantified only through orderly and systematic experiments.Computer simulation is well suited to studying these types of equipment selection and method layout problems. Several alternatives can be analyzed in a relatively short time by the modification of input variables. Also, the application of computer simulation models can significantly reduce the manpower and cost required for such analysis."

Jan 1, 1985

By N. Edmonson

During the last 30 years, a dramatic increase in the supply of byproduct sulfur substantially reduced the share of the market held by Frasch-mined (non-by-product) sulfur in North America. Even though Canadian sulfur production is not discretionary, the geographic remoteness from the large US markets and the high transportation costs associated with delivering sulfur to those markets has meant that Canadian producers act like discretionary producers in many important ways. They have effectively replaced the US Frasch producers as the cost-marginal sulfur source to large US markets. Implications of this change in market structure include more volatile sulfur prices and longer sulfur price recessions.

Jan 1, 1998

By James Boyd

REACTIVE metals are not only those sufficiently radioactive to be used as fuels, such as uranium and thorium, but all metals that will find application in power reactors. It is required of such metals that they be relatively inert or chemically unreactive, dimensionally stable at high temperatures and pressures, and either very absorbent of radioactivity or transparent to it. To gain the right perspective concerning these metals it is necessary at this point to explode some erroneous concepts propounded so often they have become accepted as fact. The first of these is that the great industrial nations, especially the U. S., have reached their pre-eminent position chiefly because they possess abundant mineral resources. Some U. S. mineral economists, echoed by the politicians, have taken this position so often that many of their theories and policies are based on the presence of developed mineral resources as a sine qua non to the country&apos;s greatness. Actually the reverse is true- under a social and political system granting free rein to the initiative and creativeness of its people, many hidden mineral resources that otherwise would have lain fallow have been developed into productive enterprises to the benefit of the national industrial economy. Again, once the proper incentive was furnished, other countries have also been able to establish valuable mineral enterprises in recent years; resources long dormant for lack of a proper economic environment suddenly have become valuable and productive. It is possible to name immediately several nations where such domestic economic developments have had favorable repercussions within the last decade. The absence of productive mines in any country is no indication that workable deposits do not exist within its territory.

Jan 11, 1957

By C. S. Lord

"AbstractThe slow progress of conventional geological reconnaissance of the northern Canadian Shield during the past twenty years clearly indicates the need for a radically new field technique. Operation Keewatin, involving the use of helicopters as the traversing vehicles, was planned and executed by the Geological Survey of Canada in response to this requirement.About 57,000 square miles of District of Keewatin, N.W.T., were mapped during the 1952 field season in appropriate detail for publication at 1 inch to 8 miles. The Operation disclosed about 14,100 square miles of Precambrian sedimentary and volcanic rocks ranging in •age from Archaean to Late Proterozoic. About 7,700 square miles of this area are underlain by greenstone. This work was accomplished in a field season of 113 days, including the spring break-up. Routine aerial geological observations were made from two helicopters flying about 300 feet above the ground; these observations were checked by more than 1,700 landings and about an equal number of aerial observations from heights of less than 50 feet. Logistical support was •provided by a Norseman aircraft on skiis or floats. Combined helicopter and Norseman flying time was about 990 hours. More than 1-00 square miles were mapped per helicopter-hour, and about 815 square miles were examined each day that both helicopters operated. The reconnaissance cost about $207,000, or $3.63 per square mile mapped.As a result of this trial use of helicopters there is now available a reasonably proven method whereby an acceptable geological reconnaissance of the barren grounds of the Canadian .Shield within the Districts of Keewatin and Mackenzie might be completed within a decade. Thus, within a few years, it could place at the disposal of the prospecting and mining fraternity data which, by conventional methods, might not be made available to this generation. Due weight must be accorded this time factor when evaluating the aerial technique."

Jan 1, 1953