Search Documents

By A. Shandilya

ACC ECOSAND is finely powdered crystalline silica, which can replace natural sand usage in concrete and plasters. ACC ECOSAND ensures a comparatively denser concrete than those made only with natural sand and / or quarry fines / Manufactured Sand (Artificial Sand). Moreover, there is a significant gain in compressive strength (10-15 %) & durability in concretes (Reduced chloride conductivity leads to increased durability). ECOSAND is a by-product of froth flotation of limestone. At ACC Madukkarai cement works, Coimbatore, Tamilnadu, full-fledged mineral beneficiation process is adopted to enhance the usage of flotation reject in concrete and plasters. Optimum level for usage of ECO-SAND is 50%. With 50% usage of natural sand+50% ECO-SAND in concrete mix, 1 day, 3 day, 7 day & 28 day compressive strength is increased by 30.1 %, 22.6 %, 15.1 % & 11.0 % respectively and with moderate chloride permeability as compare to 100% Natural Sand. Keywords: froth flotation process, beneficiation studies, Denver cell, ECOSAND, siliceous material, durability & compressive strength, RCPT

Sep 1, 2012

By Ihor Kunasz

The high lithium demand forecasted for some high tech applications and batteries for electric and hybrid-electric vehicles, in particular, has sparked increased exploration for lithium, particularly for lithium- and potassium-bearing brine deposits. The latter have generally followed the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) NI 43-101 guidelines on resource reporting, formulated for hard rock deposits (metals and industrial minerals). While a number of the requirements can be appropriately applied to brines, brines are fluids and require a specific analysis leading to a distinct set of reporting requirements. Brines cannot be considered industrial minerals because the various elements occur as ions in a dynamic fluid, rather than being chemically bonded in a solid. Although chemicals are produced from brines, brines have no relation to industrial mineral deposits. This article analyzes the recently released (Nov. 1, 2012) document CIM Best Practice Guidelines for Resource and Reserve Estimation for Lithium Brines, in light of the practical knowledge available from existing brine operations. It recommends modifications to the guidelines, which, if applied in their present format, will result in overstating resources and reserves and mislead potential investors. The CIM Best Practice Guidelines for Resource and Reserve Estimation for Lithium Brines document is generally descriptive and does not fully address the methodology for brine resource or reserve definition. Lithium and other elements (potassium, magnesium) are contained in a fluid, the hydrologic characterization of which should be the principal focus of a brine exploration program. The fundamental requirement in defining lithium brine resources and reserves in a salar is the identification and definition of those formations ? the aquifers ? that will yield brine in a usable quantity to a well, because brines can only be extracted by pumping wells. Fine-grained sediments will never, as required in the summary Table 1, have ?reasonable prospects of economic extraction,? cannot be considered and, therefore, need not be tested. However, the guidelines recommend the collection of solid samples and a high-core recovery for laboratory testing of various sediments instead of focusing on the brine.

Oct 1, 2013

By Fredrick L. Johnson

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 25,640 acres of the 29,680-acre Devil?s Garden Lava Bed, 21,040 acres of the 28,660-acre Squaw Ridge Lava Bed, and 9,100 acres of the 12,600-acre Four Craters Lava Bed Wilderness Study Areas (OR-D01-D02, OR-001-003, and OR-001-022, respectively) in order to evaluate their identified mineral resources. The study areas are located in Lake County, OR, about 50 air miles southeast of Bend. No mineral resources were identified in the three study areas. The areas are almost entirely underlain by recent lava flows. Cinder cones occur in each of the areas; however, the best cinder occurrences are in the Four Craters Lava Bed study area. Slab lava, of facing stone quality, is scattered throughout the Devil?s Garden Lava Bed study area, and to a lesser extent, in the Squaw Ridge Lava Bed study area.

Jan 1, 1987

By C. J. Wilhelm

The disposal of brines produced with crude petroleum and natural gas has been a long-continuing problem to oil and gas operators as well as to farmers and stock-raisers in the vicinity of producing fields. An impartial appraisal of conditions pertaining to the problem of brine disposal leads to the conclusion that study of the technical consideration, with proper weight given to the economic and social factors, is the most desirable approach to this problem. Brine disposal is a problem of such magnitude in certain areas in the State of Kansas that in August 1934 a cooperative agreement was made between the Kansas State Board of Health and the U. S. Bureau of Mines for a cooperative technical study of methods of brine disposal.

Jan 1, 1935

By J. Menuge, G. Barker

"Liberation (QEM-SCAN) and surface chemical (time of flight secondary ion mass spectrometry -ToF-SIMS) analyses have been undertaken on plant Pb circuit flotation samples with the aim of defining the factors resulting in sub-optimal recovery. Lead flotation circuit feed, cleaner concentrate and tails samples were examined on a size-by-size basis using QEM-SCAN. Sulfide minerals accounted for approximately one third of the flotation feed with pyrite making up 16 wt.%, followed by sphalerite (13 wt.%) and galena (3 wt.%). Non-sulfide gangue minerals comprised calcium carbonates calcite (26 wt.%), dolomite (14 wt.%) with quartz, feldspars and barite all contributing > 5 wt.%. QEM-SCAN analysis indicated that liberation was not the primary cause of the poor flotation response. Principal component analysis was applied to the ToF-SIMS data derived from five samples (as for QEM-SCAN plus rougher concentrate and tails) to enable identification of correlated surface chemical components. Although a significant range of correlations were observed we focus here on those that show a discernible pattern throughout the float circuit. It was found that for the flotation feed the surface of galena were largely obscured but where Pb was observed there was a strong correlation to surface Fe. For the rougher and cleaner concentrates the galena surfaces were relatively clean with no correlation to Fe for the rougher concentrate and minor correlation in the cleaner concentrate. However, in the rougher and cleaner tails the clear correlation of galena with Fe was again apparent. These results suggest, in combination with prior studies of pyrite morphology, that the principal factor effecting grade is the rapid oxidation of the framboidal pyrite resulting in the contamination of the galena surface with a high loading of hydrophilic oxidised Fe species, thus depressing flotation."

Jan 1, 2014

By A Buckley

Many policy issues facing the mining industry and affected communities are at a level of complexity that they can be called ‘wicked’ problems. The term ‘wicked’ in this context is used, not in the sense of iniquity, but rather as social and economic issues highly resistant to resolution. For the resource extraction sector and affected communities there are an array of challenges embedded in the industry’s production and profit paradigm, the remoteness of mineral reserves and affected communities’ expectations of economic benefit and a positive legacy. The mining industry as a whole is dominated by economic, political, legislative and market structures that influence and constrain interactions between mine operations and local communities. For communities, with particular reference to regional Western Australia, intractable problems include the uncertainty of, yet increasing dependence on, a mining economy. Questionable outcomes for local communities include the limited realisation of local employment and business development benefits, and low overall outcomes or low multiplier effects. ‘Wicked’ problems, according to the literature, are best addressed via collaboration. In the mid-west region of WA, with mining and infrastructure construction underway, alliances have formed between mining companies, the major port and rail infrastructure project (Oakajee Port and Rail) and regional and local governance stakeholders. The major impetus for these affiliations is to expedite planning and associated infrastructure development taking into account the lessons from other mineral-led regions. What has resulted is an array of innovative approaches to stubborn problems including planning well in advance of full-scale mining; regionally coordinated procurement; ‘mine ready’ local businesses; and strategic investments in social infrastructure; including community trust funds paid in advance of project delivery. This paper examines these innovative approaches/alliances and assesses their effectiveness in addressing long standing mining/community dilemmas.

Nov 22, 2011

By Debasis Barman

TBM (TBM) mining in urban areas particularly under low overburden is a big challenge to design and excavate. During excavation of the Lucknow Metro project, in Uttar Pradesh, India the metro authorities encountered a design stretch where the TBM had to cross a sewer canal crossing of 15 m length under overburden of less than 1 m. Not only the stability of TBM due to uplift was of concern but also the stability of both banks. Most structures on the canal banks were non-engineered structures whose stability due to vibration of TBM was also of concern. Due to these risks, a method was proposed that met stability requirements for both ground and superstructures. The design was practical and cost effective to construct, and a collaborative exercise between the client, contractor and designer that took approximately 18 months to implement.

Jun 13, 2023

By Brenton Cook, Nate Long, Larry Applegate, Aaron K. McCain

"The Northgate Link Extension project is the third phase of the Sound Transit master plan to extend light rail throughout the greater Seattle metropolitan area. When completed, the Northgate Link Extension will extend the existing light rail system north by about 7 km (4.3 miles) from the University of Washington to the Northgate neighborhood. A general overview of the project alignment is provided as Fig. 1. The project was funded by a combination of federal grants and allocations from local taxes. The general contractor on the project was JCM Northlink LLC (JCM), a joint venture between Jay Dee Contractors, Frank Coluccio Construction Company and Michels Corp. SoilFreeze, Inc. was retained as a subcontractor to provide ground freezing design and construction services.The project involved the construction of two parallel 5.5-m, 25-cm (18-ft, 10-in.) (inside) diameter tunnels using earth pressure balance (EPB) tunnel boring machines (TBM) and precast segmental concrete tunnel liners. The two tunnels maintained roughly the same elevation along the alignment and were spaced roughly 12 m (40 ft) apart (centerline to centerline). A total of 23 cross-passages connecting the two tunnels were included at approximate 244-m (800-ft) intervals. Cross passage excavations were elliptical in shape with dimensions of approximately 5.6 m (18.5 ft) in height and 5.3 m (17 ft) in width. The cross-passages were 5.8 to 6.1 m (19 to 20 ft) long as measured between the exterior of the tunnels at springline elevation. Cross passages were intentionally located directly beneath public right-of-ways thus avoiding buildings. Many of the cross passages were located beneath narrow roads in residential neighborhoods with mature vegetation, existing utility structures and piping and limited parking areas. Excavation and support for each cross passage was completed using the sequential excavation method (SEM).The subsurface soil and ground water conditions at the cross-passage locations were described in the Northgate Link Geotechnical Baseline Report (GBR) prepared by Jacobs Associates and the Northgate Link Geotechnical Data Report (GDR) prepared by Shannon and Wilson, Inc. Soils along the project alignment were glacially overridden and characterized as very dense or hard. Subsurface soils consisted of cohesionless sand and gravel (CSG), cohesionless silt and fine sand (CSF), cohesive clay and silt (CCS) and till and till-like deposits (TLD)."

Dec 1, 2018

By Bastian Hoffmann, Christian Moormann

The paper presents results of an experimental study on the axial load bearing behavior of vibratory driven full displacement piles in comparison with impact driven and cyclic quasi-static installed piles in dense sand. The test setup and the measurement devices used to this end are explained. Subsequently, the results of the axial loading like load settlement curves are shown and the impact of the installation method is interpreted. The results presented in this work are mainly based on three installation methods: test series one investigates axial behavior of vibratory driven piles, test series two describe the same cyclic pile installation process but without dynamic influence wherein a special test setup developed to install the piles cyclic quasi-static in the soil was used. A third test series carried out using the conventional impact pile driving method served the purpose of not only comparing the results against vibratory driving, but also aided in isolating the effects of dynamics inherent to the vibratory driving process.

May 1, 2022

By D. M. Hausen

A quantitative x-ray diffraction method has been developed for the analysis of alteration minerals in wallrock. Alteration data are plotted and contoured (analogous to geochemical data). Alteration trends outlined by this technique correlate closely with geochemical anomalies, and in some cases attend well beyond the perimeter of anomalous base metal values. "Monomineralic contouring," applied originally to porphyry-type mineralization, has been extended to other types of mineralization, including volcanogenic massive sulfide deposits. Equipment and techniques used in the quantitative measurement of alteration mineralogy are discussed.

Jan 1, 1978

By D J. Bradshaw, E M. Wightman, B Newcombe

Flash flotation plays an integral role in many of the gold and sulfide mineral concentrators around the world, and yet despite this widespread use, very little information on this unit process is available in the published literature. For operations to maximise the performance of their flash flotation circuits, understanding how these cells operate, the nature of the particles they target and how to predict whether a flash flotation cell should be used on a specific ore type is of vital importance. This paper provides a summary of the key findings of a large flash flotation research project based in the operating environment of a refractory gold concentrator. The influence of key flotation performance criteria including gas dispersion, residence time and particle segregation within the cell will be discussed and recommendations for process improvements will be made throughout. The nature of the particles within the flash cell will be examined, as will the impact on the type of particles that are passed to downstream processes when the flash flotation cell is taken off-line. The development of a laboratory method to determine whether an ore is suitable to undergo the flash flotation process is also presented for its potential to aid in flow sheet development and optimisation for new ores.CITATION:Newcombe, B, Bradshaw, D J and Wightman, E M, 2012. Into the belly of the flash à Insights into the mechanisms at work within a flash flotation cell, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 163-170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"Underground refuge alternatives require an air source to supply breathable air to the occupants. This requires pressure relief valves to prevent unsafe pressures from building up within the refuge alternative. The U.S. Mine Safety and Health Administration (MSHA) mandates that pressure relief valves prevent pressure from exceeding 1.25 kPa (0.18 psi), or as specified by the manufacturer, above mine atmospheric pressure when a fan or compressor is used for the air supply. The U.S. National Institute for Occupational Safety and Health (NIOSH) tested a variety of pressure relief valves using an instrumented test fixture consisting of data acquisition equipment, a centrifugal blower, ductwork and various sensors to determine if the subject pressure relief valves meet the MSHA requirement. Relief pressures and flow characteristics, including opening pressure and flow rate, were measured for five different pressure relief valves under a variety of conditions. The subject pressure relief valves included two off-theshelf modified check valves, two check valves used in MSHA-approved built-in-place refuge alternatives, and a commercially available valve that was designed for a steel refuge alternative and is currently being used in some built-in-place refuge alternatives. The test results showed relief pressures ranging from 0.20 to 1.53 kPa (0.03 to 0.22 psi) and flow rates up to 19.3 m3/ min (683 scfm). As tested, some of the pressure relief valves did not meet the 1.25 kPa (0.18 psi) relief specification.IntroductionThe Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the United States in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and mine safety standards enforcement (U.S. Mine Safety and Health Administration, MSHA, 2006). Section 13 of the MINER Act specifically directed the U.S. National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of refuge alternatives for underground coal mines. This mandate culminated in the 2009 adoption of changes to Title 30 of the Code of Federal Regulations (30 CFR) mining health and safety regulations, requiring underground coal mines to provide mine emergency refuge alternatives and associated components, to provide a life-sustaining environment for persons trapped underground. Such refuge alternatives can be either self-contained mobile units or built-inplace facilities. The regulatory changes also include provisions establishing requirements for MSHA approval of refuge alternatives and their components, and among these provisions are numerous criteria for providing a safe breathable atmosphere under positive pressure within the refuge alternatives. One specific criterion for maintaining a safe refuge alternative atmosphere requires the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (0.18 psi), or at a pressure above mine atmospheric pressure, in the refuge alternative, as specified by the manufacturer when the breathable air is supplied by a fan or compressor (MSHA, 2008)."

Jan 3, 2018

By N. V. Moraka

Mining companies are required by law to improve representation of women on their boards. However, progress in this regard has been slow. Boards of directors play an important role in formulating corporate strategy, risk assessment, and effective governance for sustained financial performance. Although some women have successfully maintained board seats, others have been unable to do so. It is difficult to ascertain whether women are being appointed as tokens to satisfy social pressures, as little is known about the experiences of women board members in mining, which may inform or refute tokenism. In-depth interviews were conducted with 20 women and 16 men across six listed mining companies. Thematic data analysis revealed evidence of tokenism where recruitment to mining boards is compliance-based and is informally driven by influential directors. Adverse boardroom experiences that further confirmed tokenism were reported by women, such as disregarding their contributions, condescending behaviour, and limited influence in decision-making, while other women sought to validate their competence and oppose social exclusion. This study recommends that a strong Board Chair and nominations committee is critical to ensure sustainable recruitment of competent and suitably qualified women; and further foster a culture of inclusivity and valuing gender-diverse boards.

Dec 13, 2023

By Raymond Kaufman

While there is no immediate worldwide shortage of hard minerals, the consumption of natural resources is constantly increasing, and there are ominous predictions of shortages to come. Means of meeting rapidly increasing demands are being implemented. These include such methods as exploration and discovery of new ore bodies, development of new mines, increasing production at existing mines, working or reopening known deposits of lower grade ore and tailings, recycling old materials, and developing more efficient and less wasteful processes to convert ores and metals into useful products. The United States, although itself mineral-rich, depends in large measure on imports for many key minerals and basic materials derived therefrom. According to the Department of the Interior, the U. S. depends upon imports for more than half of its supply of six of the basic thirteen raw materials required by any industrialized society - aluminum, chromium, manganese, nickel, tin, and zinc. By 1985 the country will also depend upon imports for more than half of its iron and tungsten, and by the year 2000 imports will have to supply more than half of the copper, potassium, and sulfur that it requires.

Jan 1, 1975

NEW MEMBERS The following list comprises the names of those persons who became members during the period Oct. 10, 1918, to Nov. 9, 1918. ALLER, FRANK D., Copper Met., Ore Purchaser, American Smelt. & Refin. Co., 120 Broadway, New York, N. Y. AVÈRY, PAUL W., Met. Engr., Esperanza Min. Co., Apt. 8, El Oro, Mex., Mexico. BAKER, CHARLES A., Leaching Foreman, Copper Leaching Plant, Anaconda Copper Min. Co., Anaconda, Mont: BREED, CHARLES H Met., Crown Cork & Seal Co., Baltimore, Md. CHASE, R. L., Min. Engr 102S First National Bank Bldg., Denver, Colo. EICHELBERGER, FRANK, Vice-pres. and Engr., New York-Montana Testing & Engrg. Co., Helena, Mont. GESTER, G. C., Geol., Standard Oil Co. of Cal., 616 Standard Oil Bldg., San Francisco, Cal. GRIFFIN, JOHN, Mgr., Anthracite Territory, The Dorr Co., Board of Trade Bldg., Scranton, Pa. HAYNES, ELWOOD Pres., The Haynes Stellite Co., Kokomo, Indiana. Hsi, T. C:.. Sec'y, Tayeh Iron & Steel Works, Tayeh, China. HYDE, AUSTIN T., Mgr., Keokuk Plant, River Smelt. & Refin. Co., 607 Franklin St., Keokuk, Iowa.

Jan 12, 1918

By James E. Rider

"Fractures in mine hoist drumshafts are rare. We know of no previously reported attempts to repair a fractured drumshaft; any feasible method would involve welding and the associated problems of distortion, crack formation and strength.In June 1984, a fracture was discovered in the drumshaft of the production hoist in the Teck Corporation, Lamaque Division Mine at Val d'Or, Quebec. Delivery time on a new shaft would have been at least six months. The shaft was repaired in ten days and the total out -of-service time was four weeks.This paper describes why the shaft failed, how it was repaired, and the special alignment procedures employed during re-installation to minimize stresses in the repaired area.IntroductionThe performance of a mine hoist drumshaft is absolutely critical to mine operation. An inoperable drumshaft means no hoist, which in turn means no production or mine operation.Fractures in mine hoist drumshafts are rare. Previously when they have occurred, no one has seriously considered attempting a repair because of problems involved. Any feasible method would involve welding, which raises several major problems - namely, metallurgical, alignment, and strength.In July 1984 this very situation occurred at the Teck Corporation, Lamaque Division Mine in Val d'Or, Quebec.It was recognized that a new shaft would take at least 6 months' fabrication and delivery time. However, having had some experience at repairing broken shafts in other machines under similarly desperate circumstances, and after due consideration, it was concluded that by applying the correct techniques and engaging the right expertise, it would be possible to perform a repair and have the mine back in operation within a month.Thanks to outstanding efforts by all, the repair was accomplished in ten days and total out-of-service-time was only four weeks. The causes of the failure were determined and the calculated stress levels confirmed by strain gauge measurement during operation.The success of this project was achieved by adhering rigorously to fundamental management and engineering principles."

Jan 1, 1988

By Ralf Plinninger, Pafos Busch, Richard Gradnik

This paper presents the details of the Bad Bergzabern tunnel project. This tunnel is the main part of the B427 federal road bypass, intended to improve the regional traffic infrastructure and to reduce the traffic load in the historic city centre of the health resort Bad Bergzabern. Located in the south-western part of Germany, the project area is situated at the eastern margin of the so-called Palatinate Forest, a low mountain region of mainly triassic sediments with a complex and variable geological history. The German federal government, represented by the office of mobility of Rhineland- Palatinate, awarded the contract to BeMo Tunnelling, a specialized Tunnelling company with a long history of innovation and success in NATM tunnelling. The contract includes the construction of two separate tubes with a length of approximately 1,44 km (0.9 mi)—the road (main) tunnel with a cross section of 101 m2 (1,090 sq ft) and a parallel rescue tunnel with a cross section of ca. 23 m2 (250 sq ft.) Both are connected by six cross passages. Tunnels and cross passages are excavated according to the principles of the New Austrian Tunnelling Method (NATM). Due to BeMo Tunnelling’s technical expertise and capabilities, the project team was able to engineer a speed-up concept that saves money and time for the construction team and client. This paper presents the innovative approach BeMo Tunnelling made to optimize the execution of the tunnelling works and the challenges the project team is facing with regard to a complicated geological situation, countermeasures against an increasing effect of climate change and volatile prices for construction materials.

Jun 13, 2023

By Luca Pingue, Regine Jagow-Klaff, Franco Muratore, Carlandrea Albonico, Damiano Frontini, Rudolf Wernecké

This paper describes an artificial ground freezing (AGF) application carried out to ensure both watertightness and structural support for the safe excavation of four cross passages of the Forrestfield Airport Link (FAL) project in Perth. The line will deliver 8.5 km extension of the existing urban rail network connecting the growing eastern suburbs of Perth with the existing suburban rail network. The proposed soil improvement technique is adopted as a smart alternative to jet grouting from the surface since the use of heavy equipment with long vertical mast was not allowed due to the line underpassing an airport in operation. In this paper, details of the challenges and lessons learned during both design and construction phases are given. Furthermore, it is described the geometry and the installation of freeze pipes in presence of a massive steel frame, ventilation system and slurry pipes of the tunnel boring machine (TBM) in operation. It is also illustrated the web monitoring system to allow key personnel to follow in real time the development of soil temperatures, tunnel convergences and ground surface deformations as well as changes in the interaction between international parties involved due to the COVID-19 pandemic.

May 1, 2022

By Howard Scott

The great advances made in mechanical engineering during recent years through the use of alloy steels, as illustrated by the development of the airplane and automobile, may be ascribed primarily to the application of nickel as an alloying element. The ternary system iron-carbon-nickel has a wide industrial application and forms, further, thefundamental basis of the even greater class of the widely used quarternary steels such as nickel-chromium, nickel-silicon, and nickel-vanadium. As is not uncommon with such cases of virile growth in an industry, the application of the alloy steel in a largely empirical manner has outstripped its scientific development so that a fertile field for metallographic research still remains. In this field, the basic nickel steels require first consideration and are the subject of the present investigation, which is offered as a preliminary to the study of the more complex alloys of industrial importance Of the principal tools of metallography—microscopic examination, determination of mechanical properties, and thermal analysis—the last has developed much more slowly in its application to industrial needs so that the situation often exists that heat treatment operations are based on empirically determined temperatures; that is, temperatures deterrnincd without regard to the actual transformation characteristics of the alloy. This situation is undesirable as there is no uniform standard for comparison of results. It is due, outside the usual difficulties involved in temperature measurements, to the pioneer character of much of the published work; to the lack of definiteness of the Ac, transformation,1 particularly in low-carbon steels; to the failure to define operating conditions completely; and to the paucity of information correlating thermal characteristics with results of heat treatment.

Jan 1, 1922

By Howard Scott

The great advances made in mechanical engineering during recent years through the use of alloy steels, as illustrated by the development of the airplane and automobile, may be ascribed primarily to the application of nickel as an alloying element. The ternary system iron-carbon-nickel has a wide industrial application and forms, further, thefundamental basis of the even greater class of the widely used quarternary steels such as nickel-chromium, nickel-silicon, and nickel-vanadium. As is not uncommon with such cases of virile growth in an industry, the application of the alloy steel in a largely empirical manner has outstripped its scientific development so that a fertile field for metallographic research still remains. In this field, the basic nickel steels require first consideration and are the subject of the present investigation, which is offered as a preliminary to the study of the more complex alloys of industrial importance Of the principal tools of metallography—microscopic examination, determination of mechanical properties, and thermal analysis—the last has developed much more slowly in its application to industrial needs so that the situation often exists that heat treatment operations are based on empirically determined temperatures; that is, temperatures deterrnincd without regard to the actual transformation characteristics of the alloy. This situation is undesirable as there is no uniform standard for comparison of results. It is due, outside the usual difficulties involved in temperature measurements, to the pioneer character of much of the published work; to the lack of definiteness of the Ac, transformation,1 particularly in low-carbon steels; to the failure to define operating conditions completely; and to the paucity of information correlating thermal characteristics with results of heat treatment.

Jan 1, 1922