Search Documents

By Denise Y. Dixon

The objectives of this study were to (1) document the hydrologic impacts of longwall mining on ground water, (2) identify the factors which affect the extent of dewatering, and (3) develop empirical trends to predict the extent of dewatering and recovery in advance of mining. The study was confined to three mine sites in north-central West Virginia. At each site, available ground water supplies were identified and monitored for dewatering effects and recovery. Mine A, located in Upshur County, West Virginia, has relatively thin overburden (approximately 715-280 feet). At this site domestic water supplies and specially constructed monitoring wells were monitored, continuing with an earlier study done by Cifelli arid Rauch. Most such supplies were completely dewatered over the longwall panel. Some of these wells have shown significant recovery, especially near a stream. Extensive monitoring of two nested piezometer wells revealed that dewatering generally started in advance of undermining in the lowermost monitored overburden zones first and then progressed upwards. Most dewatered wells completed in bedrock have shown no recovery, except. for valley drilled wells located within 100 feet of a Stream. Affected dug wells completed in valley alluvium rend located within 200 feet. of the nearest stream have shown significant recovery. Some wells have partially collapsed following mine subsidence. Mine B, having relatively thick overburden (approximately 585 to 900 feet), is located in Monongalia County, West Virginia. Ground water supply surveys have been conducted there in an attempt to study past dewatering effects. Owners reported Chat several wells were dewatered by longwall mining arid vertical air shafts that preceded longwall mining. Dewatered wells over longwall panels hove shown some recovery within 3 ½ years of mining. Mine C also has relatively thick overburden (approximately 585-900 feet), and is located mostly in Greene County, Pennsylvania. In addition to a survey of domestic water supplies at this site, five specially constructed monitoring wells were tested. The shallow monitoring wells suffered drops in water level due to mining but totally recovered within one day to three weeks after dewatering occurred. However, they did occasionally exhibit partial collapse during mine subsidence. Subsidence fracturing was beneficial in increasing the lateral hydraulic conductivity by a factor of about S to 22 for rock strata located within 124 feet of the surface, indicating enhanced shallow aquifer potential. One deep well suffered both partial dewatering and structural damage, with the state of water recovery bring uncertain. Also, two shallow domestic supplies out of five located over the mine were reportedly dewatered, but this claim could not, be substantiated.

Jan 1, 1988

By K. Negishi, H. Izui, Y. Komiya

"Aluminum has the disadvantage of low strength. In order to obtain the high strength composites, crystals were refined in the composites. Grain refinement was approached at two process points, generating new grains and grain growth. It is important for refinement how to control the grain growth. Spark plasma sintering (SPS) technique and TiB2powder addition prevent grain growth. To investigate effects of strain and additives to the alloy, aluminum powder was sintered at 70 MPa and 80 MPa, changing the content of TiB2additive powder by SPS method. As the results, the crystal grain size was finer in the composite sintered at higher sintering pressure and with larger amount of additive, though over 1.0mass% TiB2addition dissuades grain refining. These grain refinements improve hardness and tensile strength of sintered aluminum alloys.INTRODUCTIONAluminum matrix composites have low density, high specific strength, and low cost. Their applications are growing continuously in the field of automotive and aerospace industries. Recent studies to improve their good mechanical and tribological properties use different ceramic materials such as Al2O3(Das, Munroe, & Bandyopadhyay, 1996; Ashwatha & Anthony Xaviorb, 2014),SiC(Hassani, Bagherpour, & Qods, 2014), B4C(Ehsan, Masoud, Touradj, Amir Hossein, & Ali, 2015),TiC(Ehsan, Ali, Masoud, Kamyar, & Touradj, 2017), and TiB2(Fei & Zhong-Hua, 2013).On the other hand, grain refinement is also an important techniques for improving the properties of aluminum alloys. Finer grains improve the mechanical properties of the alloy. For cast and wrought alloys, addition of grain refiners in molten alloys accelerates generation of nucleus and suppresses grain growth. Al-Ti-B alloy is generally added as grain refiners in the molten aluminum alloys(Easton & Stjohn, 2001). Especially, TiB2has very high melting point, low density, and excellent hardness. Therefore, TiB2was selected as additions into aluminum alloys. Liquids reaction leads to high cost, oxidation, discoloration of molten alloy, and clustering of additive powder as compared with solid reaction such as sintering. However, sintering of aluminum alloy powder with ceramic powders is difficult for oxide layer surface. Recently, we take attention to spark plasma sintering (SPS) as advanced sintering process. SPS process can easily sinter a high quality specimen at a lower sintering temperature and in a shorter time than conventional sintering processes. By SPS process, we have sintered titanium powders that are as difficult to be sintered by any other processes as aluminum powders, and improved mechanical properties by adding hard ceramic powders TiC and TiB(Kamegawa, Izui, Komiya, Kobayashi, & Arimoto, 2015; Sampei, Izui, Komiya, Shigimura, & Suzuki, 2015). Furthermore, it is important to consider not only pure aluminum but alloys for solid-solution or precipitation strengthening. Actually, pure Al does not have enough strength compared with the alloys. Al-Cu alloy and Al-Mg alloy demonstrate adequate strength for industrial and commercial sectors. Al-Mg alloy retains good formability, and has high resistance to corrosion. It is therefore used for many applications. We must consider alloying processes. The most cost effective process is blended elemental technology where alloying elements are added to base powder as elemental or master alloy powder (Smugeresky & Dawson, 1981; Yasue, Radjai, Miwa, & Sakaguchi, 2003; Bolzoni, Esteban, Ruiz-Navas, & Gordo, 2012)."

Jan 1, 2018

While there have always been mining activities on the outcrops of the copper deposits around Tsumeb, large scale mining activities in Namibia only started in colonial times. Originally focusing on the known deposits, the then German Geological Survey and independent geologists soon discovered significant deposits all over the country. This eventually lead to intensive mining operations all over the country on copper, gold, diamonds, fluorspar and finally uranium. Ever since those days, mining has been one of the major economical factors of Namibia?s development, as shown in picture 1. In the Central Namib Desert mining on base metals started in 1901, and first uranium deposits were discovered as soon as 1910, later followed by others, this did, however, not lead to any mining activities on those uranium deposits in the following decades. [ ] The upswing in the use of nuclear energy in the 1960s and early 1970s triggered some extensive uranium exploration worldwide and also in Namibia. Several airborne radiometric overviews were conducted by the Geological Survey at this stage and eventually the first uranium mine was commissioned in 1976. In the following three decades, the focus of prospecting activities in Namibia shifted away from uranium again. However, since 2000 the forecast for a developing and growing global economy and its even stronger growing energy demand have triggered a large number of nuclear energy projects worldwide, thus increasing the installed nuclear energy generation capacity from 387 GW today to more than 490 GW in 2025.

Jan 1, 2011

By H. D. Keiser

Minor industrial minerals included in this chapter are: the alum minerals, bromine, calcium chloride, epsomite and other natural magnesium salts, iodine, meerschaum, quartz, industrial crystals other than quartz, and nonfuel gases (air, helium, carbon dioxide). Alum Minerals The natural alums comprise a group of hydrated double sulfates, the most important of which are potash alum, KAI(S04)2.12H20, the "alum" of popular usage; ammonium alum, (NH4)AI(SO4)2, known mineralogically as tschermigite; and soda alum, NaAI(SO4)2.12H20. Kalinite, KAI(SO4)2.11H20, and mendozite, NaAl(SO4)2, 11H20, are fibrous monoclinic alums, distinct from the isometric species potash alum and soda alum.4 Alunite, KAI3(S04)2(OH)6, also known as alumstone or alum rock, has been used as a raw material in the manufacture of alum since early times. All the natural alums are highly soluble and occur as surface evaporation products in arid regions or in sheltered places. Potash alum, together with the other natural alums, commonly occurs as an efflorescence or crevice filling in argillaceous rocks and brown coals that contain disseminated pyrite or marcasite. The mineral is derived by the action of sulfuric acid, formed during the weathering of the sulfide, upon alkali-rich aluminum silicates. Ammonia alum is found chiefly in lignite or broad-coal beds and bituminous shales. Alunite is most commonly associated with acid volcanic rocks, where the rock has been largely altered and alunite formed owing to the presence of sulfuric acid solutions or vapors. Aluminum sulfate, which for most uses is the essential ingredient of alum, may be found in saline residues resulting from the evaporation of natural water and may be formed by the action of acid waters upon aluminous rocks. A deposit of natural potash alum occurs in an irregular network of veins associated with sulfur in rhyolite in Esmeralda County, Nevada, about 35 miles west of Tonopah and 10 miles north of Silver Peak. Alum was recovered at a plant operated on the property between 1920 and 1923 by crushing the ore to ¾ in., grinding to minus 80-mesh, and counter-current leaching; the resulting alum solution was then filtered and crystallized. Alunite was of much interest during World War I as a source of potash and during World War II as a source of alumina. The wellknown deposits at Tolfa, Italy, are veins in trachyte and have been the basis of alum manufacture there since the middle of the fifteenth century. Pure alunite is insoluble in water and in common acids, but if it is heated to 500°C it loses its water of hydration, and the residue consists largely of anhydrous potash alum, part of which is readily soluble in water or acids. If the heat is increased beyond 500°C, most of the sulfur combined with the alumina is released as oxides and the residue consists of potassium sulfate and alumina. Thus, either potash alum (and aluminum sulfate) or potassium sulfate and alumina may be made. In the

Jan 1, 1960

By H Park, V Sahajwalla

"Due to the increasing amount of gangues in iron ores, a beneficiation process is required more as a preliminary step for ironmaking process. However, mechanical grinding and washing of iron ore needs tremendous effort that increases operating cost. Therefore, there is a necessity of a novel approach to ironmaking which can tolerate considerable amounts of silica or alumina. In the present study, a high alumina-carbon composite pellet was examined for an ironmaking process. The effect of compositional changes in the CaO-FexOy-Al2O3-SiO2 oxide system on the reduction of carbon composite pellets was investigated in a purpose built thermo-gravimetric analyser (TGA) at 1473K (1200¦C). As a result, alumina increased the reaction rate of carbon composite pellets by increasing surface area, while silica decreased the reaction rate by lowering surface area of samples. Infrared gas analysis assisted with the reaction kinetics of carbon composite pellets through measurement of CO and CO2 in off-gases. This study will assist with establishing the new pelletising method which differs from the conventional fluxed pellets.CITATION:Park, H and Sahajwalla, V, 2013. Effect of CaO-FexOy-Al2O3-SiO2 oxide system on the reduction of carbon composite pellets, in Proceedings Iron Ore 2013, pp 467-472 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

There have been many developments in recent years in pipeline transport to enable them to be more widely used in industry. Substantial tonnages of materials that are not affected by water, such as coal and other minerals, aggregates and wastes, can be moved over considerable distances in quite small diameter pipes. Where there are no existing road or rail facilities, long-distance pipelines are usually cheaper to install, and this advantage increases in difficult terrain. Pipeline operators all over the world assert that hydraulic lines pay for themselves in a relatively short time, in spite of the heavy capital outlay, and this is equally true for lines convey-ing slurries or pastes within a plant complex.'This paper reviews some of the more important investigations in the hydraulic transport field. Although reference to systems carrying a wide range of materials is made, the majority of recent published data centres on coal transport.The paper looks at the application to a wide range of particle sizes, the development of non-aqueous slurrying media and coal/water fuels. The review also looks at some of the equipment being proposed to provide more reliable operation and in particular the range of solids-handling pumps now available.-The paper goes on to identify areas where further research and development is required and some of the many organisations undertaking this work.

Jan 1, 1985

By E. McCullough, S. Gaillard

"Diesel particulate matter (DPM) remains a health concern in many underground metal/nonmetal mines, and has been regulated by the Mine Safety and Health Administration since 2002. While the NIOSH 5040 standard method for DPM monitoring is required to demonstrate regulatory compliance, the FLIR Airtec DPM Monitor can serve as complementary engineering tool. It is a handheld instrument that offers near real-time measurements. As part of an ongoing field study, the Airtec has been used to survey elemental carbon concentrations (a proxy for DPM) in an underground stone mine. Via “spot-checking” and more prolonged area monitoring, this effort was aimed at determining spatial and temporal DPM variation in several key locations. INTRODUCTION Diesel particulate matter (DPM) is the solid fraction of the exhaust emissions from a diesel engine. It is largely made up of elemental and organic carbon (EC and OC, respectively), which can be measured as proxies for estimating mass concentrations of DPM. The National Institute for Occupational Safety and Health (NIOSH) considers DPM to be a health hazard and potential carcinogen [1]. It is believed to cause and/or exacerbate respiratory illness upon inhalation, deposition, and retention in lung tissue [2]. Since DPM exists in both the micro- and nano-particulate ranges, it can surpass typical auto-immuno defense mechanisms that keep larger particles out of the respiratory system [2]. Relative to other occupations, the DPM exposure potential for underground miners is high because these individuals work in enclosed environments where diesel powered equipment is frequently used [3,4]. A variety of engineering and administrative controls have been devised to reduce DPM exposures in underground mines, and increased airflow is often a key component of control strategies. In large-opening mines, which are most common in the metal/nonmetal sector, DPM abatement via increased ventilation can be especially complex due to moving and controlling the large air quantities [5]. The Mine Safety and Health Administration (MSHA) has regulated DPM exposure in metal/nonmetal mines since 2002. The final rule limits personal exposure to total carbon (TC, which is the sum of EC and OC) to an eight-hour time weighted average (TWA) of 160 µg/m3. To demonstrate compliance, operators must use the NIOSH 5040 Method [6]. However, the Airtec DPM Monitor (FLIR Systems, Inc., Nashua, NH) was developed as an engineering tool to provide near real-time measurements of both EC and TC for tracking personal exposures [7]. The portable Airtec works by capturing DPM on a filter and successively measuring laser extinction on the filter as DPM accumulates; the EC fraction of the DPM is dark, and so as it accumulates the filter becomes darker and absorbs more laser light [8]. The laser extinction value is directly correlated to EC, but since EC and TC are generally observed in consistent proportions (i.e., TC = EC*1.3), the Airtec is also programmed to display TC as a TWA [9]. There have been multiple studies conducted to validate the Airtec and the instrument has been adopted by some mine operators as a tool for their health and safety programs [3,8]."

Jan 1, 2016

By J. L. Huiatt

The U.S. Bureau of Mines and Great Salt Lake Minerals and Chemical Corp. developed a froth flotation process for concentrating potassium salts from Great Salt Lake solar evaporites containing about 5 percent K. The crude evaporites, which were predominately halite (NaCl) with smaller amounts of kainite (KCl.MgSO4.2.7H20) and schoenite (K2SO4MgSO4.6H20), were conditioned in a saturated brine solution, thus converting nonfloatable kainite to the floatable mineral schoenite. Schoenite was then selectively floated with a medium-molecular weight fatty acid. Continuous small-scale pilot plant testing indicated that 80 percent of the potassium could be recovered from the crude evaporites in flotation concentrates assaying about 11 percent K.

Jan 1, 1975

The growth in the nickel market and the price increases predicted in 1970 have not mat-erialized. Several plants have been construct-ed, particularly to treat lateritic ores. A spectacular increase in cost of energy and the escalation of capital costs have led to severe economic difficulties on the part of many nickel producers. Several of the nickel prod-ucers joined together to form a Nickel Develop-ment Institute in 1984 with the prime objective of improving nickel markets. Most producers have taken exceptional action to cut overall costs as well as unit costs. Another organiz-ation made up of nickel producers, NiPERA, was established in 1980, to study and take action on problems of nickel in the environment and especially in the workplace.Ion exchange, and particularly continuous ion exchange, has been developed into a reli-able commercial unit operation in the last dec-ade. An example of how ion exchange combined with hydrogen reduction can be integrated into a Caron type reduction roast ammonium carbonate leach process for the recovery of nickel from laterites is discussed.

Jan 1, 1985

By Baohua Guo, Xuelin Yang, Tingkan Lu, Hailin Sun

The work presented in this paper mainly involves two parts. Firstly, the fundamental characteristics of the high pressure carbon dioxide gas fracturing technique (CO2 technique), including, a proposed method of TNT equivalence calculation, which is used to calculate the TNT equivalence of discharge of CO2 technique, and the comparison of the explosion volume generated by dynamite and expansion volume of liquid carbon dioxide is conducted to show the differences of fragmentation capacity between the two of them. Secondly, the coal seam fragmentation mechanisms of CO2 technique are proposed, including, 1) Gas jet cutting and penetration by shaped charge, 2) Gas volume expansion by changing phases of carbon dioxide, 3) Coal seam softening by destress blasting and 4) Coal seam fragmentation by discharge vibration, associating with the mechanisms, the equations for calculating fragmentation radius are developed and verified.

Jan 1, 2017

By Tulu B. Ihsan, Mark A. Van Dyke, Ted M. Klemetti

"How well do current modeling procedures calculate the rear abutment extent and loading? Does an improved understanding of the rear abutment extent warrant a change in standing support in bleeder entries? What is the optimal standing support for bleeder entries separated from the longwall startup room by a barrier pillar? To help answer these questions and to determine the current utilization of standing support in bleeder entries, four bleeder entries at varying distances from the startup room were instrumented, observed, and numerically modeled. This evaluation was intended to determine the rear abutment extent and magnitude at various locations to optimize standing support in these entries and those under similar conditions. This paper details observations made by NIOSH researchers in the bleeder entries of a deep cover longwall panel; specifically data collected from instrumented pumpable cribs, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was on the extent and magnitude of the abutment loading experienced by the standing support. As expected, the instrumentation of the standing supports showed very little loading relative to the capacity of the standing supports—less than 25 tons load and 1 inch convergence. The observations of the conditions showed little to no change from before the longwall panel extraction began to when the panel was more than 50% extracted. In addition to the observation and instrumentation, numerical modeling was performed to evaluate the bleeder design. The Flac3D program was used to evaluate these four bleeder entries using previously defined modeling and input parameter estimation procedures. The results indicated only a minor increase in load during the extraction of the longwall panel. The model showed a much greater increase in stress due to the development of the gateroad and bleeder entries, with about 80% of the increase associated with development and 20% with longwall extraction. The Flac3D model showed very good correlation between expected gateroad loading during panel extraction and those expected based on previous studies. The front and side abutment extent modeled was very similar to observations from this and previous panels with similar conditions. The results of this study showed that the rear abutment stress experienced by this bleeder entry design was minimal. The convergence measured in these bleeder entries was small enough not to mandate any additional support beyond development even by U.S. or Australian standards. The pumpable crib load and convergence experienced depends on the geological setting, mining geometries, and timing. The farther away from the startup room, the lower the applied load and smaller the convergence in the entry if all else is held constant. Finally, the numerical modeling method used in this study was capable of replicating the expected and measured results near seam."

Jan 1, 2017

By G. W. H. Norman

Introduction During the past few years emphasis has been placed on the importance of major faults, fault zones, and associated structures in localizing ore deposition. This interest has developed partly through experience in mining camps in other parts of the world, and partly by the discovery of such structures associated with ore deposits in the Abitibi region, northwestern Quebec. The recognition of these structures has been brought about chiefly by detailed mapping that has been gradually extended along most of the southern gold belt of Quebec and across adjacent parts of Ontario. In the Chibougamau region of northern Abitibi, progress has been made in the mapping of major faults by using aeroplane photographs with a scale of about 1,000 feet to one inch for field mapping. These studies have shown that many large faults occur in the Abitibi region; also that there is a relationship, direct or indirect, between faults and mineral deposition. The faults are, however, of more than one type and age, and this should be clearly appreciated in any planned programme for prospecting this great region adequately. The information regarding faults and structure is so widely scattered that it is difficult to obtain a clear picture of the essential features, either for planned prospecting or for analysis and development of ideas for further study. This paper, as originally conceived, was intended only to discuss and compare the regional structure of southern Abitibi county-where detail mapping and diamond drilling have been carried on intensively for the past ten years-and of the less well-known Chibougamau district, in order that the experience gained in the one area could be usefully applied in the other. However, a comparison of the two districts leads naturally to a consideration of their common relationship to certain major late-Precambrian structures that form an important northeast system across the southeastern part of the Canadian Shield.

Jan 1, 1946

By M. J. Ferrante

The Bureau of Mines recovered rhenium powder from scrap tungsten alloy containing approximately 25 percent rhenium. Oxidation of the scrap at 950° C separated volatile rhenium heptoxide from tungsten trioxide. Minor amounts of tungsten, iron, and nickel were removed by selective precipitation from a rhenium solution from which was recovered crystalline ammonium perrhenate. Experimentation showed that hydrogen reduction of minus 325-mesh ammonium perrhenate at 1,000° C produced rhenium powder averaging 2.1 microns in size (Fisher Sub-Sieve method). The powder contained <50 ppm of total metallic impurities and 1,070 ppm of total interstitial impurities. Sintered compacts had a density of 95 percent of theoretical. Approximately 96 percent of the rhenium contained in the scrap alloy was recovered.

Jan 1, 1969

By D. R. Gladwell

This study examined the-feasibility of clay mineral identification and quantification by reflectance radiometry and subsequently developed a computer algorithm for deconvolution of the component spectra. Clay mineral analysis of 53 rocks and soils from Alberta, Saskatchewan, Ontario and Nevada by X-ray diffraction (XRD) compare favourably with the radiometric determinations. The application of the technique to precious metal exploration was examined at the Horse Canyon epithermal gold deposit, Cortez Mine, Nevada where low levels of illite and kaolinite are present alongside local silicification. Consequent on the success of the laboratory and field work a field portable clay mineral analysis system was designed and constructed.

Jan 1, 1985

By Rajashekhar Marthi

Lithium is a key component for future electric vehicle batteries and energy storage. The future availability of lithium to meet the growing demands remains in question. Around 60% of lithium resources exist in the form of continental brines. Traditional methods to recover lithium from brines use solar concentration with precipitation and have found limitations in lithium extraction due to interference of Mg in high Mg/Li brines. Thus, there is a need for highly selective adsorbents. Recently, spinel structured delithiated lithium manganese oxides have demonstrated promising results. However, due to the small particle sizes, it is economically difficult to recover the adsorbents and thereby limits industrial applications. In our work, LiMn2O4 ion sieve was synthesized and immobilized on diatomaceous earth. Fundamental adsorption studies were carried out in lithium buffer solutions to understand the nature of adsorption and kinetics. The adsorbents were also tested for recycle stability, as well as recovery of lithium from Great Salt Lake water samples.

By H. K. Lin, J. L. Oleson

The purpose of this study is to develop a mathematical model to describe the oxidation of cyanide with SO2as proposed in the Inco process. This research employed a direct method for measuring the change in cyanide concentration with respect to time as effected by varying concentrations of SO2, copper and pH. Developing this model may be applicable in determining optimum conditions in a process well known and used in the mining industry. It was determined that the reaction is first-order with respect to cyanide, SO2and [Cu+2].The reaction order is 0.15, or zeroth order with respect to [H+] at pH range from 8.0 to 9.5.The activation energy, Ea, is 21.6 kJ/mol. The overall rate equation, as determined through this study is: [ ]

Jan 1, 2004

By John C. Machisak

STATISTICAL data on injuries and employment pertinent to metal mines and to their mills, and/or processing plants are presented in this Information Circular for the calendar year 1960. The information pertains to metal mines, as well as ore-dressing plants and primary nonferrous smelters, refineries and reduction plants, and their auxiliary works. These data are voluntarily submitted annually to the Bureau of Mines by the operators, and contribute greatly toward the promotion of safety in the mineral industries. The data presented are classified according to the principal mineral produced and include information on copper, iron, lead-zinc, gold-silver lode, gold placer, uranium-vanadium and miscellaneous metals. A breakdown of miscellaneous metals by commodities is shown in table 19, page 41. The data also relate to workers engaged in production, exploration, development, construction, and maintenance and repair work, as well as supervisory personnel and office- workers at the mine or plant site. Injury and employment data at metal mines and metallurgical plants in the United States for 1960 are shown under the following general sections:

Jan 1, 1963

By Rafael Valencia-Dongo, Ernesto Ramírez, Julio Tapia

Enfocado en una novedosa metodología de resolución de conflictos basada en la teoría de juegos, este artículo propone estrategias para generar un equilibrio estable entre empresa, Estado y comunidad. Tras evaluar la tipología y características de la conflictividad socioambiental por acción de líderes opositores a la inversión, se desarrolla un marco de resolución de conflictos a través de lo que se denominan pactos de contrapeso, que cubren los ámbitos de comunicación, gestión sociopolítica y fidelización del trabajador minero. Estos pactos permiten cambiar la percepción, incentivos y acciones de los actores, lo que incluye la acción de terceros legítimos.

Sep 30, 2019

By I. C. Edwards, E. O. Lilge, H. H. Mccreedy

"Introductory and GeneralTHE DRIESSEN CONE bas been used fairly extensively commercially as a classifier. Its use as a concentrator in the upgrading of ores at a fairly high ratio of concentration with concomitant recoveries has been almost negligible. Certain known features about the cone, however, such as its high throughput capacity, cheapness of construction and operation, and simplicity of design have attracted the attention of mill men. An inadequate knowledge of the operating characteristics of the cone when used as a concentrator seems to have been the main reason for its lack of use. It was for this reason that the present investigations§ were undertaken to determine the operating characteristics of the cone and its application to the concentration of uranium ores, with particular emphasis being placed on the concentration of low-grade uranium ores.The investigations were started in December, 1951, and have continued uninterrupted to the present. The initial work was confined chiefly to investigating the operating characteristics of the cone in order to establish the trends that certain variables would exert on the general metallurgy of uranium concentration. Optimum metallurgy was therefore not the prime initial objective."

Jan 1, 1955

By John Chipman, Donald W. Murphy

RECENT developments in iron alloys containing nitrogen have indicated that this element may exert a considerable influence on the properties of the metal. This influence is not always in an undesirable direction and the indications are that nitrogen should be regarded as an alloying element, the amount of which should be subject to control, rather than as an inherently deleterious impurity. In controlling this element in liquid iron to the best advantage, it is necessary to have a reliable background of fundamental data pertaining to solubilities, rates of solution and chemical reactions of nitrogen in liquid iron. Obviously, the first step in such an investigation is the determination of the solubility of nitrogen in pure iron, and this has been the object of the experiments described in this paper. The solubility of nitrogen in solid iron has been measured by Zurich,1 Sieverts,2 Martin,3 and Iwasé4 and, the agreement among the first three inspires confidence in their results. No accurate determinations of its solubility in liquid iron have been recorded though several investigators have obtained approximate results. Strauss5 was able to introduce 0.03 to 0.04 per cent nitrogen into steel by the action of either ammonia or nitrogen on the liquid metal. This was accomplished by Eilender and

Jan 1, 1935