Search Documents

By D. E. Walsh

Over a period of seven years (1989-1996) the Mineral Industry Research Laboratory (MIRL) University of Alaska Fairbanks, has investigated the effects of temperature, residence time, and particle size on the degree of low-rank coal (LRC) upgrading for a non-evaporative, hydrothermal drying process, also known as hot water drying (HWD). Three Alaskan LRCs were used in this study: Usibelli coal (Seam No.4) from the Nenana Coal Field, Little Tonzona coal from near McGrath, and Beluga coal from the Beluga-Yentna field on the west side of Cook Inlet. Replicated, factorial tests were conducted. Experimental results indicate that most of the low-rank coal upgrading via HWD occurs rapidly within the first 10-20 minutes of residence time. Thereafter, the upgrading process slows down and over 100 minutes of additional residence time are required to produce similar percentage increases in coal properties to those achieved in the first 10-20 minutes. The properties of the hot water dried products were very sensitive to process temperature. Calorific value, carbon and oxygen contents, equilibrium moisture levels and Hardgrove grindabilities all appear to change linearly with temperature within the 275" C to 325" C range.

Jan 1, 1997

By Xueyuan Nie, Xuezhi Zhang, Henry Hu, Shen Xinwei, Jimi Tjong, Li Fang

With the demand for weight reduction in vehicles and airplanes, researchers have shown great interested in casting wrought aluminum alloy 7075 because of its potential advantages such as high strength-to-density ratio and stress-reduction capabilities. It is therefore essential to conduct a fundamental investigation on solidification behavior and grain microstructure of alloy 7075. In this study, a commercially-available wrought aluminum alloy 7075 was used to study the solidification behavior of alloy 7075. A thermal analysis was performed based on the cooling curve and its corresponding first and second derivative curves. The nucleation of the primary a-Al phase and eutectic phases were analyzed. The comparison between the microstructures of the wrought and cast 7075 alloys shows that coarse microstructure and porosity are present in the cast alloy. The techniques for grain refinement in casting, such as the addition of the nucleating particles and applied pressure, should be employed to reduce the dendrite arm spacing and the porosity.

Jan 1, 2015

By Norman L. Kotraba

In Electric Arc Furnace (EAF) steelmaking, dust emissions are collected in a baghouse to prevent their escape to the Environment. This fine dust, predominantly iron oxide, also contains oxides of various other metals introduced into the EAF from the scrap charge. For example, mixed or galvanized scrap brings with it zinc, lead, and small quantities of cadmium which preferentially accumulate in the collected off-gas dust. Stainless steel scrap brings chromium into the charge, some of which also makes its way into the baghouse dust as hexavalent chromium-containing oxides. Because many of the contained heavy metal oxides are water-leachable, the U. S. Environmental Protection Agency has listed EAF dust as a hazardous waste which, as of August 8, 1988, cannot be 1andfi11ed without first being treated. Moreover, beginning August 8, 1991, all dusts with zinc concentrations of 15% or greater will be required to undergo high temperature thermal treatment to remove the heavy metals prior to any further disposal. This deadline represents several EPA-granted time extensions to the original requirements; extensions which were granted to allow for further development of process technologies.

Jan 1, 1991

By E. R. Maize

This report is the third of a series on convergence of roof and floor in coal mines and subsidence of surface that accompanies it. The first paper5/ dealt with extraction in a mechanized mine (Montour 10) having relatively short rib lines that retreat rapidly. The second dealt with extraction in a mine (Crucible) in which coal was loaded. by hand and in which the rib lines wore long and slow-moving. The present report deals with a mine (Gibson) in which conditions approximated those in the Crucible mine, except that the distance between room centers was considerably less and the pillars were narrower in consequence. Moreover, the average cover was less and the studies were made under the steep hillside of a stream valley compared with a gently rolling surface over the portions of the second mine studied. Gibson mine lies in the east-central hart of Washington County, Pa. , approximately midway between the Montour 10 end Crucible mines on a north-south line. A cooperative agreement covering the work was made with the Hillman Coal & Coke Co. through W. L. Affelder, vice president. This paper describes the methods used in the investigation, gives excerpts from the data obtained, and offers such generalizations as appear to be justified.

Jan 1, 1940

By Makoto Ohlsuka

The ternary Ni2MnGa intermetallic compound is an intelligent material which has both a ferromagnetic property and a shape memory effect (SME). The use of the shape memory alloy films for an actuator of micro-machines is very attractive because of its large recovery force. The purpose of the present study is to investigate the effects of fabrication conditions and to clarify the relationships between these properties and fabrication conditions of the Ni-Mn-Ga films. The Ni-Mn-Ga films with a thickness of nearly 5 um were deposited with a radio-frequency magnetron sputtering apparatus using a Ni50Mn25Ga25 or Ni52Mn24Ga24 target. They were heat-treated at various temperatures between 873 and 1273 K for homogenization and ordering and then cooled in a furnace. The composition of the films depended on the sputtering power. The as-deposited films were crystalline and had columnar grains. After the heat treatment the grains widened and the grain boundary became indistinct with the increasing heat treatment temperature. The martensitic transformation temperature of the heat-treated films increased with increasing nickel content. Furthermore the effect of plastic deformation and constraint aging on SME is also investigated. After plastic deformation, the two-way SME was shown through the martensitie transformation and its reversion, The intensity of X-ray diffraction peaks from stress-induced martensitie phase was found. The constraint-aged films also showed the two-way 3ME by thermal cycling.

Jan 1, 2003

By Makoto Ohtsuka

The ternary Ni2MnGa intermetallic compound is an intelligent material which has both a ferromagnetic property and a shape memory effect (SMB), The use of the shape memory alloy films for an actuator of micro-machines is very attractive because of its large recovery force, The purpose of the present study is to investigate the effects of fabrication conditions and to clarify the relationships between these properties and fabrication conditions of the Ni-Mn-Ga films, The Ni-Mn-Ga films with a thickness of nearly 5 um were deposited with a radio-frequency magnetron sputtering apparatus using a NisoMn2sGa25 or Nis2Mn24Ga24 target. They were heat-treated at various temperatures between 873 and 1273 K for homogenization and ordering and then cooled in a furnace, The composition of the films depended on the sputtering power. The as-deposited films were crystalline and had columnar grains, After the heat treatment the grains widened and the grain boundary became indistinct with the increasing heat treatment temperature, The martcnsitie transformation temperature of the heat-treated films increased with increasing nickel content. Furthermore the effect of plastic deformation and constraint aging on SME is also investigated, After plastic deformation, the two-way SME was shown through the martensitie transformation and its reversion, The intensity of X-ray diffraction peaks from stress-induced martensitie phase was found, The constraint-aged films also showed the two-way 5MB by thermal cycling,

Jan 1, 2003

By Thomas V. Falkie

The purpose of this work was to investigate the rate at which coal is delivered from the underground working face by gathering arm type loaders as employed on continuous mining machines, to identify the factors -- geometrical, geological, mechanical, or procedural which affect the delivery rate, and to develop quantitative rate descriptive equations for the loading function. The mathematical techniques employed were factor analysis and multiple linear regression. It was determined that the coal-cutting function of the continuous mining machine is the factor that primarily influences the loading function. The geometrical factors -- the dimensions of the work area in relation to the dimensions of the mining machine - were the factors of secondary influence. Fifty-five percent of the experimental variation in the loading function was explained in terms of the six most prominent independent variables. It is expected that this work will be useful in operations-research studies as applied to underground coal mining, and with refinement will enable mine planners to select equipment based on the operating characteristics of the equipment and the mining conditions.

Jan 1, 1972

By Kenneth H. Johnston

This publication describes a thermal-recovery project and two waterflood projects in Carter, Garvin, and Stephens Counties, Okla., that will be visited during the 1966 annual tour by the Bureau of Mines in cooperation with the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects arc (1) the movement of heavy (15° to 28° API gravity) crude oil through the reservoir and into the well bore with energy furnished by burning a portion of the crude oil therein; (2) the use of an inverted nine-spot pattern with dually completed injection wells, to produce oil from deep (8,200 to 10,200 feet) reservoirs; and (3) the flooding of five sand lenses separately by using controlled water injections through multizone completed injection wells. Discussion of the individual projects includes information on their early history, method of completing and operating wells, source and treatment of injection fluids, oil production decline curves, and the results obtained from the development.

Jan 1, 1966

"In conjunction with Banick Mercur , Wright Engineers Limited designed the first multi-stage aqueous pressure oxidation system in an alkaline environment in North America. A three-stage slurry heating and slurry pressure let-down with heat recovery was an innovative approach to the problem of high energy cost with the low sulphur content of the ore. The design of this system required solving a number of problems associated with heating and pumping of slurries at pressures up to 3230 kPa and temperatures in excess of 220°C. Wright received an Award of Merit in October 1989, from the Canadian Consulting Engineering Awards Committee in the Process Category for its design of the Mercur pressure oxidation system.The Mercur Mine is located at the south end of the Oquirrh Mountains in Tooele County about 65 miles by road from Salt Lake City, Utah, U.S.A. The original mill was designed to process 5000 tpd of oxidized gold ore in a carbon-in-leach (CIL) circuit. A new ore treatment system was required to treat the substantial quantities of refractory ore reserves which could not be treated economically in the existing mill. The new pressure oxidation circuit makes the refractory ore amenable to gold recovery by oxidation of the sulphides contained in the ore .Wright Engineers Limited was commissioned by Barrick Mercur Gold Mine Ltd ., a wholly-owned subsidiary of American Barrick Resources, to design the pressure oxidation facility. This followed completion of a feasibility study by Wright which showed that the project was technically and economically viable.Work on the feasibility study began in 1986, detail design commenced in February 1987, and was completed in December 1987. Mechanical installation was completed in January 1988, and slurry feed began in February 1988. The plant has operated since June 1988 without major interruption . Wright was responsible for engineering, procurement and construction management for the addition of the 750 tpd pressure oxidation circuit to the existing mill and also had commissioning responsibility.Major unit processes involved in the pressure oxidation facility are ore thickening, three-stage slurry preheating, pressure oxidation and three-stage slurry cooling with heat recovery, stearn generation, propane and oxygen storage and a video graphic display process control system were included in the scope as process anciliaries.The pressure oxidation increases gold recovery from the refractory ore by conventional CIL from as low as 35% to more than 86070. A patent has been granted for the process."

Jan 1, 1989

By Kevin G. Stricklin

Introduction Continuous monitoring techniques have been used in the US and abroad for many years. A continuous miner has a monitor that measures methane and automatically gives a warning if the methane exceeds 1%. It deenergizes the continuous mining machine automatically at a maximum concentration of 2%. Main fans are also continually monitored to ensure operation. Alarms may also be given at a remote location should a fan slow or stop. The systems being developed can continuously monitor various gases and equipment throughout the mine and transmit pertinent data to a surface monitoring station. At this station, conditions throughout the mine can be monitored and, in some instances, controlled. These are known as Mine Wide Monitoring Systems (MWMS). History The use of environmental monitoring systems began in 1976 when a federal court approved the petition of modification to use belt air at the face. The first mine to receive a modification did install a system to supplement existing safeguards. Later, the Mine Safety and Health Administration (MSHA) and the US Bureau of Mines (USBM) conducted tests dealing with the use of belt air. Findings from these tests are being used to set guidelines as requirements of a petition. These requirements include: • Velocity of air has to be 0.25 to 1.5 m/sec (50 to 300 fpm); • Monitors will be installed at each belt drive and tailpiece and at intervals not to exceed 610 m (2000 ft); and • An alarm level of 10 ppm, above the ambient level is appropriate. The early uses of environmental monitoring could only be used outby the last open crosscut. That may be a reason for an initial slow growth of these systems. In June 1982, MSHA began evaluating systems that could be used in returns to ensure that monitoring systems being used in areas where permissible equipment is required does not of itself pose an explosion hazard. This is known as the Mine Wide Monitoring Systems Evaluations and Sensor Classification program. The evaluations and classifications granted are based on electric currents and voltages. Use of mine wide monitoring systems The environmental aspect of MWMS in today's coal industry deals with carbon monoxide (CO), methane (CH4), and air velocity. Just as all mines are different and encounter different problems, the MWMS are diverse and can be used to provide necessary data in all areas of coal mines. Mine operators in an ultragassy seam, for example, may be concerned with monitoring methane, while a mine that used diesel equipment may want to continuously monitor for diesel contaminants. In a mine with roof fall problems, airflow monitors may be helpful as an indication of whether the air is flowing in its normal course and at its normal volume. Today's MWMS can monitor any or all of these parameters. Most systems can be expanded as mining needs require. For example, a mine is now being monitored for methane and five years from now CO monitoring would help increase safety. It may be possible to use the same system by adding additional equipment. In the US, 30 environmental monitoring systems were installed from May 1985 through May 1986. In 1984 and 1985, there were 38 and 44 environmental monitoring systems in operation, respectively. Due to mine closings, 11 of these are no longer in use. However, the number of mines using environmental monitoring systems increased to 63. Use of these systems are not limited to any geographic area or

Jan 9, 1987

By Raymond E. Krauss

The McLaughlin Mine is based on a world class epithermal gold deposit located in the coastal thrust fault of northern California, about 1 12 air km (70 air miles) north of San Francisco. Owned and operated by Homestake Mining Co., the McLaughlin deposit contains about 18 Mt (20 million st) of gold ore at an average grade of 5.2 g/t (0.152 oz per st), or about 93 t (3 million oz). The area was identified as a gold target by Homestake in early 1978. Drilling confirmed it to be a commercial deposit by 1980. The mine was then planned, engineered, built and brought into production by March of 1985. The deposit was historically a part of the Knoxville District. It was mined for cinnabar, which was used to produce mercury for use in recovering gold and silver in the Mother Lode and Comstock districts. At that time, the mine was called the Manhatten and later the One Shot Mine. It was worked for more than 100 years, producing about 76,000 flasks of mercury without any awareness of the presence of economic concentrations of gold. By 1978, the site was largely disturbed and entirely unreclaimed.

Jan 1, 1990

By Charles Mitke

(San Francisco Meeting, September, 1915) INTRODUCTION THE Copper Queen mine is composed of seven divisions which are operated through the following shafts: Division Shaft Depth, Air Current No. Feet Uncle Sam 600 Downcast (shut clown April, 1914, to 1 curtail production) Southwest 600 Downcast 2 Czar 400 Downcast 3 Holbrook 600 Downcast 4 Spray S00 Downcast (shut clown April, 1914, to curtail production) 5 Gardner 1,000 Downcast 6 1 Dallas 1,400 Downcast 1 Lowell 1,600 Upcast 7 Sacramento 1,700 Downcast " I I The workings of the different shafts are connected by motor-haulage drifts on the even numbered levels. The general location of the orebodies and workings is illustrated by the vertical projection of orebodies of the district as shown in Fig. 1. The Uncle Sam, Southwest, and Czar workings have many connections to the surface through raises and extensive cracks that were caused by moving ground. These divisions are cool and are ventilated entirely by natural means. The Holbrook is ventilated partly by natural and partly by artificial ventilation, while the Spray, Gardner, Lowell; and Sacramento are ventilated entirely by mechanical means. In some of the divisions mentioned above a considerable quantity of air exhausts through shafts of adjoining properties.

Jan 9, 1915

By Claude MacDonald, John H. Ashburn

"IntroductionIndustrial growth and technological change over recent years had been accompanied by two major sources of concern to management and employees: (a) increase in occupational injury and illness and the resultant costs involved; and (b) equipment damage and breakdowns in concentrated production lines causing more extensive loss potential.Due to economic factors, management attention has focussed more on production and quality than on safety, health and related loss potential sources. As a result , occupational safety and health activism has grown, government legislation of compensation and occupational safety and health standards have progressively developed and stronger liability attitudes have been taken by courts of law.To improve efficiency and allow development in more competitive markets, rising labour costs, equipment costs and safety related financial losses have dictated that attention be given to conservation of all resources. Conservation of resources, people, equipment, material and environment, can no longer be addressed in isolation but must be managed integrally with production and quality. To this end, systems have developed utilizing sound management principles applied with equal intensity to production, quality and loss potential"

Jan 1, 1987

By M. Z. Emad, M. U. Khan, A. ur Rehman

Stemming plugs are used as an accessory in drilling and blasting industry. They supplement conventional stemming material (i.e. drill cutting) with retention of gases in the drill hole that result in better fragmentation of rock and improved explosive utilization. Better fragmentation and explosive utilization along with economic benefits enhance efficacy of the project. Incorporation of stemming plugs in drilling and blasting industry is in exercise for about thirty years. The efficiency of stemming plugs is a key factor in their rising induction in mining industry. Different studies have been conducted on the economic viability of these plugs. The focus of this paper is the selection of stemming plugs for a bench blasting operation and the examination of blasting operation efficiency based on ergonomics and human factors. Three types of stemming plugs were evaluated during multiple blasts at a limestone quarry. Their performance was evaluated using split desktop software. Based on the human factors plastic molded stemming plug (stemming plug-1) was found to be the best among all selected plugs. INTRODUCTION Surface mines and quarrying operations heavily depend on bench blasting to achieve high volumetric targets and production demands. Use of explosives is the most economic method adopted for rock breakage and movement. Extensive research had been performed to enhance explosives energy utilization. This include changing the drilling pattern, application of air decks, stemming plugs, and use of other supportive devices. Optimization of explosive energy has been a major concern in those mines that rely on drilling and blasting operation to carry out main production. Due to continually increasing cost, efficient mining demands, and associated hazards of using explosives, it is necessary to utilize explosives at their best. Efficiency of a blasting operation is generally evaluated by the fragmentation size. From post blast conditions at blasting site to efficiency of processing plant, anything can be affected due to improper blast resulting in bad fragmentation. Better fragmentation is necessity for better operation of the system along with consideration of the safety of operation, environmental issues and related costs. For developing a blast design, an engineer should always attempt to minimize the cost of operation without compromising with acceptable technical and safety necessities [1]. Blast performance is dependent on many different factors associated with the process. These factors have been gauged as blast geometry, explosive specification, and rock mass properties [2]. Similarly, in 2013 Mohammad et al. concluded that fragmentation dynamics depends on blast hole diameter, primer, spacing, stemming, burden, and delay timing for blasting operation [1]. At the work site where this study was performed, blast holes were filled by drill cuttings and muds to help in confining gases. In a blast hole, gas confinement helps in better rock fragmentation along with reduced flyrocks. This practice is most common in many countries including Pakistan. Due to lack of homogenized particle size, the effectiveness of confinement is variable and majorly based on the size of stemming. Extremely small sized drill cuttings often result in hole blow out along with flyrocks from the collar. This improper blast energy will result in poor blast, bad impacts on environment, and reduced operational efficiency. In addition to the stemming material, the length of stemming is also a prime consideration. The decrease in stemming length will increase the quantity of explosive in the blast hole and an increase in stemming material generally improves stemming performance.

Jan 1, 2019

By Larry A. Haas

The U.S. Bureau of Mines is investigating ways of enhancing the high-temperature softening-melting (HTSM) properties of domestic taconite pellets. These properties, which are important for determining the performance of pellets in blast furnaces, include pellet bed contraction, pressure drop, S-value (area under the pressure-temperature curve), and softening and metal-slag drainout temperatures. Experiments showed that HTSM properties were related to the physiochemical properties (fired strengths and reducibilities) of pellets containing different levels of limestone and dolomite flux. Flux additions resulted in slightly lower green and fired pellet strengths, but improved metallurgical properties, such as reducibility. The influence of reduction conditions on HTSM properties was evaluated by varying the pellet metallization starting temperature and the carbon monoxide content of the CO-N2 gas mixture. HTSM property change was more sensitive to flux addition levels when metallization was initiated at 1,100° C with 20 pct CO in the gas stream. The S-value and the metal-slag drainout temperature were found to be the best criteria for characterizing HTSM properties. The optimum flux addition level was about 8 pct (4 pct dolomite, 4 pct limestone) or a basicity of about 1. At higher flux levels, a higher metal-slag drainout temperature was obtained.

Jan 1, 2010

By J. Hollow, D. Walsh

The Fort Knox Mine is located in Alaska’s interior, where the average ambient air temperatures range from -24oC in January to 16oC in July. The mill processes a free milling gold ore utilizing both a gravity recovery circuit and a conventional cyanide leach/carbon-in-pulp circuits. Mathematical models have been developed to accurately predict the impact of leach circuit slurry temperature on gold leach, carbon adsorption and cyanide destruction kinetics. Additionally, an energy balance approach has been used to model the seasonal variations in slurry temperatures throughout the Fort Knox mill. The energy balance model, combined with the kinetics models previously developed to predict plant performance, was used to justify a tailing thickener installation at the Fort Knox Mine. This paper describes the development of the energy balance model and its prediction of plant performance assuming a tailings wash thickener to reduce heat loss from the mill. Also presented is an analysis of the post project plant performance that validates the model and shows the mine produced an additional 596 kg (19,155 ounces) of gold, while reducing mill reagent costs by $6,302,000 during the first 38 months of operation.

Jan 1, 2007

By Kenneth H. Johnston

This publication describes a thermal-recovery project and two waterflood projects in Carter, Garvin, and Stephens Counties, Okla., that will be visited during the 1966 annual tour by the Bureau of Mines in cooperation with the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects arc (1) the movement of heavy (15° to 28° API gravity) crude oil through the reservoir and into the well bore with energy furnished by burning a portion of the crude oil therein; (2) the use of an inverted nine-spot pattern with dually completed injection wells, to produce oil from deep (8,200 to 10,200 feet) reservoirs; and (3) the flooding of five sand lenses separately by using controlled water injections through multizone completed injection wells. Discussion of the individual projects includes information on their early history, method of completing and operating wells, source and treatment of injection fluids, oil production decline curves, and the results obtained from the development.

Jan 1, 1966

By Meagan S. Boltz

From October 2000 to April 2001 a local array of fourteen seismograph stations was deployed at the Trail Mountain Mine (TMM), an underground coal mine in Emery County, Utah, to locate mining-induced seismicity (MIS). Original analysis of the data provided epicentral locations that coincided closely with the active longwall panel. The original analysis yielded poor quality hypocenters, however, preventing a useful relation from being made between mining activity and the event depths. For the original analysis, only stations at elevations above mine level were used for locating MIS. As a result, P- and S-arrival times from four of the stations in the local array were not used: an inmine station and three stations at elevations below mine level. This study compares mine workings and active mining to a revised TMM dataset that included P- and S-arrival times from the lower elevation stations that were not used in the previous study. In the revised locations, a modified master event methodology was used to calculate station delays. These station delays correct for errors in the shallow layers of the velocity model. The resulting hypocentral locations have improved depth resolution, determined by a lower root mean square (RMS) for the locations, compared to the original study. Most of the events occur in the roof of the mine and follow the longwall panel. When located using the velocity model determined in the original study, the elevations of the events increase as the longwall panel progresses. One possible explanation for the elevation increase is that it may be related to geology or the caving process. As presented here, a 10% decrease in the shallow velocity structure results in a more plausible location for the hypocenters. Consequently, it is hypothesized that progressive development of the TMM longwall panel(s) may have resulted in a progressive change in the velocity model.

Jan 1, 2012

By David S. Robertson, Richard F. Douglas

"Uranium is a lithophile element of relatively low natural abundance. Concentrations of uranium form through processes of erosion and sedimentation, and over 90 per cent of the western world's uranium ore reserves are in sedimentary rocks.Proterozoic quartz-pebble conglomerates contain about 60 per cent of the known uranium reserves. These are all similar in appearance, in mode of distribution and in manner of origin. They carry uranium minerals and/or gold and abundant pyrite. Their unique distribution in Huronian time required a pre-existing crust well enough evolved to have plentiful quartz and abundant gold, uranium and pyrite. The materials of value were deposited as detrital heavy minerals prior to the appearance of an oxidizing atmosphere in late Proterozoic time.Epigenetic uranium deposits occur in arkosic sedimentary rocks through the entire geological column. About 30 per cent of the western world's known ore reserves are in _these rocks. This type of deposit is particularly prominent in semi-arid parts of the United States, having yielded most of the uranium ore produced and containing nearly all of the known reserves.The Western States type"" of deposits occur in lenticular, permeable stream-laid sedimentary rocks. The de-posits are believed to have been precipitated from moving ground water at locations where plant debris or other organic matter had accumulated. The uranium may be derived from volcanic sediments, which are commonly associated with the units containing the ore, or it may be leached from exposed granite surfaces or from granitic debris which forms the sediments.A significant part of the world's uranium resources are in black shales and lignitic rocks. The lignites that contain uranium are virtually valueless as potential sources of heat. Uranium concentrations at levels such as to be potential sources of by-product uranium occur in many phosphorites.Reworked sediments may provide uranium in pegmatites and vein-like deposits."

Jan 1, 1970

Develop a safer, more effective, and more efficient method to control fires in abandoned coal mines and waste banks. Maintain the costs of this new method at less than or comparable to conventional AMI fire control methods. How It Works Cryogenic extinguishment of subsurface fires is a method of heat transfer. Bureau-designed injection equipment produces a pumpable slurry of liquid nitrogen and solid particles of carbon dioxide. Liquid or gaseous carbon dioxide from a pressurized tank flows to a bell-shaped nozzle where the change in pressure causes the carbon dioxide to form a granular snow. The solid carbon dioxide is mixed with liquid nitrogen. A jet pump is used to move the slurry through the delivery lines and into a simple injection probe. At injection, the nitrogen vaporizes and the carbon dioxide sublimes. This phase change produces a cold gas (-180° C) that, as it expands and moves in all directions, removes heat and also displaces oxygen. This combined process inhibits the combustion process and lowers the temperature below the reignition point. When the liquid nitrogen and solid carbon dioxide are converted to gases, the expanding gas acts like a piston, forcing warm air out of the porous bed, Although smoke and hot gases arc forced from the burning coal, generally there is no significant increase in the odor associated with burning coal.

Jan 1, 1992