Search Documents

By Rojas M. Raúl

Durante el proceso de explotación de la mina Cerro de Pasco y dada la cercanía de la ciudad misma, esta se ha visto afectada por los problemas de vibración del terreno. En este sentido, el objeto del texto es determinar un control de las vibraciones a través de la voladura en el tajo Mc Cune de dicho yacimiento y así evitar daños a las construcciones civiles y labores de explotación subterránea.

Nov 8, 1984

By L. B. Beneitone

Over the years, the rope changing procedure on the two double-drum San Manuel ore hoists has been streamlined and improved, so that a job that once required eight hours to complete is now finished in four. The ropes, constructed of improved plow steel, 6 x 25 filler wire, pre-formed, right lay, Lang lay with a fiber core and weighing 8 ½ lb per ft, have a 2 ¼ in. diam and are 3200 ft long. They have widely varying lives, but on the average a rope change on one of the two hoists is required every six months. When a rope change becomes necessary, the ropes on both drums of a hoist are replaced. Thorough planning and preparation are essential for efficient rope changes. A briefing session is held on the day prior to the change, during which the entire procedure is reviewed on a blackboard and discussed among the cable rigging crew. These discussions have led to many improvements that have been incorporated into the present rope changing procedure.

Jan 4, 1968

By Thomas J. Peters

In 1979 and 1980, the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the 15,600 acre (6,310 ha) Freel Peak RARE II area (No. 5271) in the Lake Tahoe Management Unit. This study by the Bureau of Mines indicates that potential for economic mineral resources in the area is slight. The only mineralized structures in the area consists of two quartz veins. One quartz vein, at the Mountain Top Mine (fig. 1), located by Fred Denner in 1932, is estimated to contain 2,000 tons (1,800 t) of silver and copper-bearing resources. Chip samples from the vein averaged 0.61 oz silver per ton (20.91 g/t), and 1.59 percent copper. The narrow vein is not economically mineable. The other quartz vein is poorly exposed and contains traces of molybdenum. A second reported molybdenum occurrence could not be substantiated.

Jan 1, 1982

By A. A. Cochran

Bureau of MinesThe Bureau of Mines studied the development of practical methods for recovering manganese from the extensive domestic resources of low-grade ores and open hearth slags. A one-step operation was developed on a laboratory scale in which manganese and iron compounds are treated with chlorine, volatilized, and separated by selective condensation. Manganese recoveries of 90 to nearly 100 percent were obtained from 9 of the most important domestic ores. Analyses of the manganese chloride product indicated that it was suit-able for aqueous electrolysis with little additional purification. A complete, integrated process that provides for the recovery and recycling of chlorine is proposed. This process appears to have distinct advantages over previously proposed manganese recovery processes, and, in sharp contrast to leaching procedures, it is applicable to practically any manganese-bearing material.

Jan 1, 1967

By N. A. Gokcen

The construction and operation of a simple and accurate vacuum-fusion apparatus are described in detail. Absolute accuracy of the oxygen analysis has been determined by the reduction of oxides weighed to 20.01 mg. The Bureau of Standards steel samples have been analyzed repeatedly, and their inadequacy for the acceptable range of oxygen is presented. The limits of interference of manganese, aluminum, and titanium, and the effects of tin and water-cooling of the furnace tube have been investigated in detail. ANALYSIS by the vacuum-fusion method consists of melting a sample in a degassed graphite crucible under high vacuum and extracting oxygen as carbon monoxide, and nitrogen and hydrogen as gaseous elements. The resulting gas mixture is analyzed for its constituents, from which oxygen, nitrogen, and frequently hydrogen may be determined within 1/2 hr or less. The history and summary of methods1-4 and extensive reviews of literature'.' for the determination of gases in metals have been published in detail. The foundation of the modern vacuum-fusion method of analysis was laid by Jordan and Eckman,11 and Oberhoffer and his associates.1, 10 Diergarten,11, 12 Meyer,13 Thanheiser et al.,14, 15 Ericson and Benedicks,16 Ziegler,17, 18 Sloman,16-23 Thompson et al.,24 and later many others contributed to the improvement, accuracy, and limitations of the method. In some investigations, however, the limitations of the procedure and the errors involved in the analysis require further critical examination and evaluation. In many apparatuses, lunnecessarily complicated and cumbersome features and elaborate precautionary measures do not have conclusive advantages. The purpose of this invest:igation was, therefore, a) to construct a very simple and accurate apparatus, b) to determine the absolute accuracy of results, c) to establish the limits of interference of manganese. aluminum, and titanium, d) to reexamine critically the reduction and recovery of oxygen from oxide powders of various sizes, and e) to evaluate critically the eight steels of the Bureau of Standards."' Apparatus The apparatus used in this investigation is shown in Fig. 1. It has been used for over three years, during which several modifications were made. A brief description of the apparatus is as follows. The transparent silica or Vycor tube, E, is joined to the Pyrex head, B, by mean of a face to face ground joint sealed with mercury. A similarly sealed ball and socket joint would also have been satisfactory. A standard tapered ground joint, successfully used by some investigators, was tried, but in the absence of grease or vacuum cement it was very difficult to disassemble the joint. The graphite crucible, G, 15/16 or l 1/8 in. OD, 2 1/2 or 3 in. high, 1/10 in. wall, shown enlarged in Fig. 3a, is made from the rods containing less than 0.08 pet ash. Two baffles, overlapping sufficiently to prevent spattering, are inserted in two opposite slots cut on a band saw. Two small holes in the baffles permit the temperature measurement of the melt. A second type of crucible, Fig. 2, G, shown enlarged in Fig. 3b, is also satisfactory, though not as convenient as the crucible shown in Fig. 3a. Somewhat similar but more elaborate crucibles with baffles were first tried by Ericson and Benedicks,'" but were abandoned in favor of a crucible with a stopper and a peripheral graphite powder filter. Various versions of their crucible with a stopper have later been used by other analysts, 10-27, 27-30 The crucible is packed directly in E, Figs. 1 and 2, with —35 + 48 graphite powder for shielding and insulation. A minimum layer of 7 mm of powder is necessary for keeping E cool and minimizing the blank. The first use of graphite powder was made by Sloman,10-23 Who found that —200 mesh was the most satisfactory. The author tried various size powders from +20 to —100 mesh and found that a) particles of 28 mesh or larger were not sufficiently insulating and were heated by the induction current, b) the powder finer than 60 mesh packed too much and did not readily permit the escape of gases even when the crucible was heated very slowly; hence, the powder was occasionally blown out of the side in the crucible and in the mercury pump. The optimum size powder is, therefore, 35 to 48 mesh size or 0.4 mm in average diameter. The furnace is designed to eliminate excessive amounts of

Jan 1, 1959

By Augustus J. Bowie

THE discovery of the auriferous cement gravel deposits in and near Deadwood Gulch, Lawrence County, Dakota Territory, in 1876, created a mining excitement, and rush to the Black Hills. Numerous ten and twenty-stamp mills were built on Deadwood Gulch ; Central City and the town of Deadwood sprang into existence, and became the centres of the mining industry of the Hills. Gold quartz deposits were subsequently discovered and located on a so-called mineral belt, extending from Whitewood Creek on the south, to Deadwood Gulch on the north. A northerly group of these quartz locations was purchased in December, 1877, by parties in San Francisco,, who formed a company, incorporated under the name of the Father de Smet Consolidated Gold Mining Company. This company immediately commenced the work of exploration. The deposits were proved to be extensive, and easily mined, but it was found that the ore, on an average, would not. yield more than $10.00 per ton* of 2000 pounds. At this time the cost of supplies and materials in the Hills was high. Miners' wages were $3.50 per diem, and custom mills charged $6:00. per ton. The successful working of mines on "the belt" necessitated cheap milling. The ores being of so low grade,† this could be accomplished only with large and economically running mills. To insure the greatest possible economy, the Father,& Smet mill * Up to December 31st, 1879; the de Smet mine had produced bullion of the value of $718,211.68 from 76,155 tons of ore, being an average value of $9.41 per ton. During the year ending December 31st, 1879, the mine produced 46,344 tons, which yielded $425,360.42, or $9.18 per ton. The total gross cost of working for the corresponding period, including deadwork, exchange, legal expenses, fete., wits $219,914.82. The yield of the mine for the year 1880 (Engineering and Mining Journal, February 5th, 1881), was $600,011, with total expenses of mining and milling, of $313,108. † The first 4083 tons extracted from the de Smet mine, were selected, yielding $62,783.97. The next 25,728 tons produced $230,067.24. The total 29,811 tons were weighed, and worked at custom mills. The yield of the first 409 tons from tine Golden Terra Mine was $11.44 per-ton.

Jan 1, 1882

By D. B. Paterson

In view of decreasing head grades, the relatively high gold price, and recent developments in metal evaluation, an exercise was initiated to determine the extent of gold concentration, the mode of occurrence, and the areas of concentration within the run-of-mine milling circuits of Randfontein Estates Gold Mining Company (Witwatersrand) Limited. The total gold content of three of the thirteen run-of-mine mils in the Group was measured as a typical lock-up of approximately 200 kg per mil. The majority of this gold was concentrated either behind the grid-type body liners or within the pockets of the body liners. This paper is an account of the experimental procedure and the results obtained, and highlights possible means of limiting gold lock-up in future.

Jan 1, 1988

This paper suggests the models for determination the optimum life of machines on the basis of sum and difference of investment and maintenance costs. The economic-mathematical models are based on complex percentage method taking into account the time factor of referring cost. The following strategies of maintenance policy have been considered in machines repair: a strategy without investment, a strategy with continuous investment and a strategy with step-like investment. The effect of value of investment in repairing and time interval of investment on optimum machine exploitation life has also been considered. An illustrative example is presented.

Jan 1, 2003

LIBERIAN ore has been called the richest iron ore mined in the world, and thus far, the output from the Liberian Mining Co.'s Bomi Hills mine has lived up to its reputation. Iron content has been variously given as 68.47 pct to 68.825 pct. A recent United Nations survey gave it first place, surplanting the previously top-rated Swedish product. The first shipment of Liberian ore to the United States reached Baltimore in June, 1952 and went into blast furnaces at Republic Steel's Cleveland plant, where excellent results were reported. The physical make-up of the ore was hard, dense lumps, free of fines and with ideal size distribution. The Bomi hills mines were scheduled to be in full operation by the end of 1952. At the close of 1951, 200,000 tons of ore had been delivered to Baltimore. Liberian Mining Co. states that production is about 90,000 tons of ore per month at present. Between 1200 and 1500 men are employed at the mine site, with about 25 pct of them Americans. The Bomi Hill project was financed with the aid of the Export Import bank, which loaned Liberia Mining part of the sum needed to initiate and put the development into production. No definite expansion plans are in the making but extensive diamond drilling is being pursued. Original estimates of annual production for Bomi Hills ran in the neighborhood of 1.5 million tons, but the figure is no longer applicable. Liberia's potential as an iron producing country has been known for a long time, but the physical obstacles in the way of large scale production were such as to prohibit even contemplation of the project. Until recent years, the only route from the mine site to Monrovia was a foot trail. Once to the coast, over swamps and unbridged rivers, the ore was still useless because of the lack of loading facilities. Transportation Solved One problem was solved with the completion of the artificial harbor at Monrovia. Harbor construction was well under way when the mine project began in 1948. The island location of Monrovia also made the building of a bridge across the St. Paul River necessary. The 980 ft reinforced concrete structure, accommodating railroad and vehicular traffic, was opened in 1949. Meanwhile, preliminary work on railroad construction started. Grading was completed quickly. In April, 1951, the first train made the trip from Monrovia to the Bomi Hills. About half of the cost of the entire project went into railroad construction. More than 2200 men, often forced to resort to primitive methods, were engaged in clearing a path through the heavy forests between the mine and port. Swamps were drained and filled, and bridges, including the William V. S. Tubman, named for the Liberian President, were constructed. At the port, a Robbins Conveyor Belt Co., orehandling plant was installed. Ships can be loaded from the stockpile at the rate of 3000 tons per hr and vessels need spend only one day in port. Liberian Mining is operating under an 80 year lease, giving the company exclusive mining rights to all minerals, except gold, platinum, and diamonds, within a 40 mile radius of Bomi Hills. The contract provides a fixed royalty to the Liberian Government of five cents per ton of ore extracted, and a premium -based on the New York market price for Bessemer-grade pig iron. The entire project started because an American,

Jan 1, 1952

By B. Beatty

Discussion by B. Beatty This is a response to M.J. Hrebar's paper, which tracks in detail the highly productive stripping capabilities of modern large bulldozers at two separate installations. It proves the old adage "economies of scale" and quantifies the advantage of being able to move large loads of dirt over comparatively short haul distances by sliding rather than carrying the load. This discussion examines whether a bulldozer is the most efficient way of using this geotechnical principle. Case 1 - Study eastern US: Contour coal stripping application The energy consumption for the Case 1 mining method (eastern US contour stripping operation) shows the D11 averaged 117 L (31 gal) of diesel fuel per scheduled hour, and produced 333.3 bank m3 (436 bank cu yd) per scheduled hour (0.351 L/m3). Assuming 1 L (0.26 gal) of diesel fuel contains 10.4 kW-hr of energy, the unit expenditure of fuel energy for Case 1 Study was 3.66 kWh/m3. Another way of shifting this material is by using an overburden slusher (OS), as shown in Fig. 1. The OS as shown in Fig. I. The OS is electrically powered and consists of a manned low wall winch (LW ), a remote controlled (radio telemetry) highwall winch (HW) and a hoe. The winches operate to pull the hoe back and forth across the pit. The hoe carries load in the forward direction ahead of a rear mounted blade and returns empty. A spreadsheet (Lotus 123) simulation package, BOSSIM, models the OS operation on a load by load basis over a wide range of pit configurations. The geometry shown in Fig. 2 of the paper was modeled using BOSSI M and the results are summarized in Table1. Table 1 shows a LW with 150 kW (200 hp) and a HW of 120 kW (160 hp) installed power, towing a 15-m3 (19-cu yd) hoe, would accomplish the Case 1 stripping task at about the same scheduled stripping rate (D11=333 m3/hr or 433 cu yd/ hour, OS=342 m3/hr or 447 cu yd/ hour). It was assumed the winches in this equipment have an electromechanical efficiency of 90%. This gives an average electrical energy expenditure rate of 151 kW-hr, and a unit energy expenditure level of 0.44 kWhr/m-3(0.57 cu yd/kWh)-an improvement of 8291%- over the D11 alternative. The energy comparison illustrates the importance of using more efficient electric power if possible, ahead of the internal combustion engine, and delivering power from a fixed ground position rather than through a moving track system. Another important energy observation is the comparative action of the dozer blade and the OS hoe. The former implement continuously digs and spills as it works the load forward. The OS hoe digs the load until full, the blade then lifts due to the contained load pressure and a shear plane forms under the mass, enabling it to slide forward in a force reduced - transporting mode. Economic comparison Table 2 operating cost per scheduled hour and unit cost comparison follows a format used in Tables 2 and 3 of Hrebar's paper and compares Case 1 Study with the OS alternative. Drill and blast costs are kept constant in both cases, although when larger OS units are considered, it is expected these costs will reduce because bigger hoe sizes will permit larger rocks to be transported efficiently.

Jan 1, 1995

By T. W. West

During the design and construction of a coal preparation facility, there are many items that can cause serious problems if not properly handled in the early stages of a project. These problems can be a detriment to smooth owner/ contractor relationships, the designing of a flow sheet, the selection of equipment, the design of the facility, the maintenance of schedule and budget, and a smooth start-up. It is the purpose of this presentation to identify some of these problems and to suggest steps that can be taken to reduce or eliminate their impact.

Jan 1, 1977

By L. B. Clarke

The optimal maintenance and control of the air flow and pressure distribution in a mine network are achieved by the correct positioning of the mine fans and regulators within the mine ventilation circuit. The principal considerations are the location of the main and underground fans or regulators and the attendant control of mine leakage. Air flow control is achieved by either passive or active regulation. Passive regulation adds resistance, usually in the form of a regulating door. Active regulation adds pressure sources in the form of underground booster fans. Ventilation engineers are increasingly turning to analytical tools to assist them in the design and operation of ventilation systems. The application of computer methods, formal optimisation methods and numerical solution methods is outlined

Jul 1, 1996

By Leo Horvitz

Microanalysis of near-surface soils for hydrocarbons is the basis of a method for locating gas and oil deposits. To substantiate this technique, evidence of vertical migration of hydrocarbons from petroleum accumulations is presented. Tabulated data relevant to hydrocarbon surveys conducted in several petroleum provinces are included. PEROLEUM and natural gas are composed principally of the saturated hydrocarbons ranging from methane, the lightest, to nonvolatile liquids and solids containing approximately thirty-five carbon atoms. A technique for locating buried accumulations of these hydrocarbons before drilling obviously requires that some of the hydrocarbons leave the deposit and migrate toward the surface of the earth where they may be detected in their original form. Earliest attempts to link near surface hydrocarbons to petroleum at depth were apparently made by Laubmeyer' in Germany and by Sokolov in Russia. These investigators collected samples of soil air from boreholes one to two meters deep and analyzed them for traces of hydrocarbons. They found that soil air over producing areas is richer in these constituents than is soil air over barren areas. Since 1936 work on petroleum exploration techniques of this type has been going on in this country. However, instead of determining hydrocarbon content of soil air collected in the field, investigators analyze samples of the soil itself for adsorbed and occluded hydrocarbons, which are released by suitable treatment and found in larger amounts than are the quantities reported for soil air. Difficulties often encountered in collecting gas samples in the field, moreover, are eliminated when soil is used as the sampling medium. Field Procedure: Sample locations are first surveyed over the area to be investigated. Care is taken to locate the stations at considerable distances from roads, pipelines, drilling wells, and other sources of contamination. The borehole pay be dug with a bucket-type hand auger or with mechanical drilling equipment. Lubricants are avoided in either case. When the desired depth is reached, a sample is brought to the surface, placed in a pint glass jar or can, and securely sealed. Sample containers are carefully labeled and delivered to the analytical laboratory. Generally a satisfactory sampling depth range is 8 to 12 ft. In some regions, however, satisfactory data are obtained from samples collected at much shallower depths. Such is the case, for example, in areas of west Texas where the limestone and caliche near the surface occlude hydrocarbons and prevent their rapid escape to the atmosphere. In carrying out broad reconnaissance surveys in search of large features, considerable time is saved by first taking samples one-fourth to one-half mile apart along profiles about one mile apart. If the analytical data indicate a hydrocarbon anomaly of interest, additional samples are taken to produce a more dense and uniform sampling pattern within the interesting area. This sampling program is particularly adaptable to areas that are sectionized. In areas covered with a network of roads, sampling along these roads facilitates the reconnaissance survey. Actual sampling density used depends upon areal extent of features expected. When flanks of piercement-type domes where accumulations may be only several hundred feet wide are sampled, stations are often no more than 200 ft apart. Analytical Technique: Of the hydrocarbons composing petroleum, only the more volatile would be expected to reach the surface of the earth. The analytical technique, therefore, was developed to determine only those constituents that exert a vapor pressure at room temperature. Actually, in near-surface soils, only a very small part of the hydrocarbons are heavier than pentane. Details of the analytical technique have previously been reported. Only a brief description of the methods will be presented here. A weighed portion of the sample, about 100 g, is first treated with an aqueous solution of copper sulphate and then with phosphoric acid in a partial vacuum. The copper sulphate prevents the reaction of the acid with carbides that may be present because the sample has been contaminated by auger particles. Such a reaction may produce spurious methane. The role of the acid is to decompose any carbonates present, thereby helping to release the hydrocarbons. The carbon dioxide is removed with potassium hydroxide and the flask containing the

Jan 1, 1955

The oxidation of zinc vapour plays a very important part in the operation of the Imperial Smelting Process. The kinetics of the reoxidation of zinc vapour by carbon dioxide and water vapour onto quartz and zinc oxide substrates is qualitatively understood and this pertains to the conditions found as the gases are being transferred from the furnace to the splash condenser. However, re-oxidation also occurs in the shaft of the furnace where the solid substrates are sinter and metallurgical coke. It was found that there was a threefold increase in the rate of oxidation on sinter, compared to quartz and a 30 to 300 increase in rate on the coke. This was attributed to the high surface area offered by these materials.

Jan 1, 2003

The oxidation of zinc vapour plays a very important part in the operation of the Imperial Smelting Process. The kinetics of the reoxidation of zinc vapour by carbon dioxide and water vapour onto quartz and zinc oxide substrates is qualitatively understood and this pertains to the conditions found as the gases are being transferred from the furnace to the splash condenser. However, re-oxidation also occurs in the shaft of the furnace where the solid substrates are sinter and metallurgical coke. It was found that there was a threefold increase in the rate of oxidation on sinter, compared to quartz and a 30 to 300 increase in rate on the coke. This was attributed to the high surface area offered by these materials.

Jan 1, 2003

By Fathi Habashi

Nitric Acid has been used for over 50 years in the uranium industry and in phosphate fertilizer manufacture. Its application in the treatment of sulfide concentrates is relatively recent. A review of recent developments is given.

Jan 1, 1999

By S. Mohanta, I. D. Behera, B. Sahoo

"Run-of-mine coal contains particles of different sizes with different specific gravities, and when this coal is crushed, the amount of material present in a particular density class changes. This alters the washability characteristics of the coal, which affects the quantity, quality, and separation efficiency of the gravity-based coal washing process. The degree of difficulty in washing a typical coal at a particular specific gravity depends mostly on the amount of material occurring within ±0.1 specific gravity range, which is known as ‘near-gravity material’ at that particular specific gravity of separation. In this paper, two numerical indices, namely ‘near-gravity material index’ and ‘index of washability’, are used to quantify the distribution of near-gravity material in different density classes and to evaluate the degree of difficulty involved in the washing process. The results of this preliminary investigation indicate the uniform distribution of near-gravity material in all density classes for finer size fractions, whereas for coarser size fractions more near-gravity material is present in the lower density classes, making the washing process more difficult at a lower specific gravity of separation. IntroductionThe prime objective of coal beneficiation is to remove physical impurities as effectively and economically as possible. The beneficiation process includes various operations on the asmined coal to make it more suitable for enduse application without destroying the physical identity of the coal. There are several coal beneficiation processes, but gravity-based separators remain the most efficient unit operation for removing the undesirable gangue material from run-of-mine coal. These separators exploit the difference in density between coal particles and gangue particles to effect a separation. The feed is introduced into an aqueous suspension of ultrafine magnetite with a particular density. The feed particles with a relative density less than that of the suspension (clean coal) float to the top surface of the suspension, whereas particles denser than the suspension density (gangue material) sink to the bottom. When the difference in density between the particle and the aqueous suspension is large, the separation is easy, but when this difference is less the separation becomes much more difficult since the settling velocity of the particles is very low. This lower settling velocity increases the probability that particles that should report to floats report to sinks, and vice versa, hence increasing the amount of misplaced material. Therefore, the degree of difficulty in beneficiating a typical coal at a particular specific gravity depends on the amount of material occurring within ±0.1 specific gravity range. This is known as ‘neargravity’ material, also termed ‘near-dense’ material, at that particular specific gravity of separation."

Jan 1, 2016

By F. T. Cawood

One of the consequences of globalizing mine finance is a necessity to apply uniform accountancy and valuation standards that are clearly understood and consistently applied by the global investment community. However, each country has unique circumstances, which sometimes make it difficult to align domestic practice with international requirements. South Africa is no exception and issues such as its political history, a taxation regime enforcing different rules on different mineral producers and a unique mineral rights ownership distribution, are barriers to internationalization. The economy is in a transitional phase as a result of the many and diverse policy documents following the change in political dispensation in 1994. Many of these documents have recently been implemented through new legislation and, in the case of mining, negotiations are continuing in order to ensure an acceptable outcome. This paper discusses the challenges that the South African minerals industry faces in the field of mineral property valuation. It draws on international experience and includes a discussion on the unique considerations that the South African mineral property market must take into account in establishing a code for this purpose, as such a code could later be aligned with international practice.

Jan 1, 2004

By Johannes Moeljono, Werner Wenzel, Heinrich Wilhelm Gudenhau

As an important mechanism for increasing production of the suction-draft-sinter process, it has been shown that gas permeability through the sinter layer plays an important role. Methods to increase production rates have been indicated and suggestions for carrying out the process have been made to improve the rate of production, reduce the fuel consumption, and at the same time obtain a uniform sinter. Laboratory experiments were conducted at the Institute for Ferrous Metallurgy of the Technical University at Aachen to illustrate these methods. Methods of Increasing Gas Penetration Through Sinter Layers The following are of fundamental importance in determining the process cycle during the sintering of iron ores: 1) Generation of maximum temperature, since its form and range determine sinter quality. 2) Propagation velocity of the temperature maximum which controls the attainable output. 3) The convective heat transfer which influences the velocity of travel of the temperature maximum.

Jan 1, 1974

By D. Jean Hutchinson, Mark Diederichs

"Cable bolts are an important support component in modern underground mines. If an optimized cable bolt system is to be achieved, it is insufficient to focus on cable bolt layout design or on cable bolt installation in isolation. Cable bolt support, like all engineered systems, requires a holistic approach, encompassing integrated elements of design, implementation and verification. The “Cable bolting Cycle” described in this paper incorporates these components along with related tools and procedures which should be used together to ensure effective and efficient cable bolt support.Design involves the consideration of demand, capacity and constraints as outlined in this paper. The demands imposed on the sup-port system by the rock mass response to excavation under the combined action of stress and gravity must be matched to the capacity of the cable bolt array. The cable bolt system capacity is a function of the component strengths of the steel strand and the bond (load transfer) and by the deformation response and retention characteristics of the system. The design is bounded by operational and economic constraints.Implementation of the cable bolt array can then proceed and must include appropriate protocols of communication, training and quality control, in addition to both general and site specific installation procedures. Implementation will be discussed as the sum of these components.Implementation of the cable bolt array can then proceed and must include appropriate protocols of communication, training and quality control, in addition to both general and site specific installation procedures. Implementation will be discussed as the sum of these components.The information presented in this paper represents a very abbreviated version of much broader concepts, procedures and design charts, presented in a practical cable bolting handbook by Hutchinson and Diederichs (1996)."

Jan 1, 1996