Search Documents

By Alan K. Burton

Along with tires and transmission systems, engines have been a limiting factor in the growth of large off- highway trucks. The problem, primarily, has been the development of reliable, high-performance engines that are not prohibitively heavy or expensive. For many years, horsepower to overall truck weight ratios have been in the vicinity of 300 lb per hp for rear dump units up to 50 tons capacity. This ratio is obviously very poor when compared to the much lighter and smaller highway trucks, which frequently have a performance ratio of 100 lb per hp. Unfortunately, the larger mining trucks have not been able to match even the 50-ton trucks, and in some cases, ratios have dropped as low as 450 lb per hp. This results in a performance of only 67% of that achieved by the older smaller trucks. Thus, the message is clear: what is needed is more horsepower and less weight.

Jan 10, 1975

To provide a method for locating trapped miners promptly and accurately. The Approach: Develop a wireless emergency system that is intrinsically safe, compact, easy to operate, reliable, sturdy, and economical. How It Works: A (one transmitter has been developed under Bureau of Mines contracts. The transmitter weighs only a few ounces, is powered by a cap lamp battery, arid can be carried on the miner's belt. A compact loop antenna, which could either be carried by the miner or strategically located in the mine, is used to generate a magnetic field that is sensed by a mobile receiver on the surface. When needed, the antenna is deployed to form a single loop. In mines where the overburden is less than 600 feet, a loop of No. 19 wire approximately 30 feet in circumference is normally adequate. This antenna weighs less than one half pound. In deeper mines, a heavier wire and bigger loop is required; a No. 10 wire deployed around a pillar has been used.

Jan 1, 1974

By R. C. Ferguson, B. Bernstrom

R.C. Ferguson (District Manager, Hardinge Company Inc., Hibbing, Minn.) — In the opening paragraph of Mr. Bernstrom's paper he stated that the Cascade mill performance information is preliminary. With the completion of the 1962 operating season, more reliable performance information became available. The main bearings, which had been damaged, were reconditioned at the factory. New Gatke bearing bushings with a 120° are of contact were supplied. Provision was made to introduce high pressure lubricant at two points in each bearing. New spherical bearing balls that operate in spherical seats were aligned at the factory and held in place by several setscrews to aid in installing the bearings in the field. The screws were not loosened prior to, or during, operation; therefore, the bearings operated as rigid bearings. The lubricant cooling system was changed to the cooling tower type to provide lubricating water of a suitable temperature. Another refinement consisted of installing a device to add a set percentage of soluble oil to the make-up water.

Jan 1, 1963

By E. G. Kelly

Many methods of evaluating the efficiency of mineral separations have been described in the literature. In most cases, these present the efficiency as a single number. This paper argues that single-number measures of efficiency are inadequate because they seldom allow reliable comparisons, and are unlikely to correspond to the optimum operating conditions. To realistically make comparisons, it is necessary to distinguish the particle-induced component from the equipment- induced component. In a number of situations where the separating property can be identified (such as in gravity concentration and classification), this can often be done. However, in more complicated systems, such as flotation, this has not been possible. A technique is described whereby particle and equipment contributions to efficiency can be distinguished without the need to define the separation property. Because smelter schedules define a boundary correlation between grade and recovery, they generate some of the better single¬-number measures of efficiency, but even these have limitations.

Jan 1, 1991

By D. E. Kraushaar

Ruhrkohle in West Germany evaluates and compares the net present values of long-term periods from its coal mines by a computer assisted long-term planning system. Two main parts of this system are computer programs for the prediction of: (a) mineable reserves and their distribution in longwall panels as a function of dependent geological variables; (b) daily outputs and costs of longwall panels as a function of dependent geo- logical, layout and operational variables. This paper describes the investigations, which ended in the above computer programs: ? the collection of information from past workings and their organization in databases; ? the statistical evaluation of the databases, and ? the resulting correlation formulas. The correlation formulas vary the mean dependent variables as a function of independent variables which can be indicated with high reliability for planning projects in the long run. The system thus serves the purpose of facilitating long-term planning and excluding biased individual judgement of local planning staffs.

Jan 1, 1987

By U. E. Paakkinen

Progress in computer control of flotation circuits has developed parallel with advances in reliability of on-stream X-ray analysis (Cooper, 1976). Attainment of acceptable results with X-ray fluorescence analysis over the past ten years has led to application of computer control in more than 30 concentrators. Gains in applying flotation control also have given incentive to improving measurement and control devices for other essential functions in control systems. At the same time, advancing technology has made available computer systems having characteristics practical and economical for the physical environments of concentrators and ore processing plants. Benefits from flotation control have centered on increased efficiency in mineral separations, derived by stabilizing circuit operation subject to changing ore characteristics. The gains have been most evident in processing complex ores for multiple concentrate products. In many cases, particularly when coupled with grinding control, the economic results from on-line control have been substantial compared to investments in monitoring and control equipment.

Jan 1, 1979

By L. Kilpinen, K. R. Kay, H. B. Fowler

"FOREWORDThe International Nickel Company of Canada has built four ore concentrating plants since 1950. The fifth and largest is now under construction. In each successive plant, the level and type of instrument control and sophistication of control techniques have increased as experience was gained. The type of control progress is illustrated in Fig. 1.At Frood-Stobie the high degree of instrumentation and the level of control were made possible by the constant evolution of techniques and improved instrument hardware technology. We have established in practice concepts that are sound, although many modifications to instrument sensor types and locations 1-rere often necessary. It is generally true that at other existing Inco mills, it is possible to run ""all manual"" for protracted lengths of time because of operator availability and dependence. The Frood-Stobie Mill is the exception, and it is the degree of reliability of the instrumentation hardware and level of maintenance that has made this possible."

Jan 1, 1971

By Kai Kang, Jun Bao, Shouping Liu, Xiao Sun

Powder characteristics have a significant influence on selective laser melting (SLM) process. In this research, particle size, surface contour and the microstructure of IN718 powder used in SLM were tested, and the physical and chemical changes during heating process of the powder were investigated as well. The shape characteristic and fluid properties of IN718 powder were defined and measured. It is shows that most particles of IN718 powder exhibited nearly spherical shapes, and the particle size is about 22.95μm. On this basis, IN718 sample was fabricated by SLM process using the powder and the microstructure of the fabricated sample was investigated. The results indicated that the sample has a dense microstructure, no macro-defects but a few micropores and porosity. Compared with the powder, there was no new phase formed in the sample and melting point of the sample was little less than that of the powder.

Jan 1, 2015

By Mark S. Rayson, Jessy Lee, David O. Johnson, Matthew R. Rawls

The ability to manipulate the structure of liquid chemicals in an explosive is important in mining applications, where precision blasting is crucial for the safe, reliable, economical and eco-friendly extraction of ores. Static mixers allow explosives, emulsion-based in particular, to be custom-made as they offer precise and reproducible mixing without the need for moving mechanical parts. In this paper, we perform numerical simulations on the laminar mixing of two nitrate-based fluids in a Kenics static mixer unit for various mixer parameters. Two numerical methods were investigated in the study of the mixing pattern: solving the mass transfer equation and using particle tracking. The former introduces artificial numerical diffusion which can lead to spurious smearing of the component boundaries, a problem that can be avoided with the latter technique. We have also demonstrated that the particle tracing method is capable of qualitatively predicting the blending patterns under the conditions studied.

Jan 1, 2014

To quickly and more reliably measure the alignment and deflection of mine guides used to run skips and cages into a mine shaft. The Problem Conventional mine guide alignment measuring systems require the use of a plumb bob and tape measure. This method is not only laborious, but it is time consuming as well. Approach Aware of the drawbacks of the current measuring method, the Bureau of Mines designed a self-contained instrument system that can accurately perform vertical guide alignment and deflection measurements by remote control. How It Works The Bureau-developed instrumentation system, called the Guide Alignment Measuring System (GAMS), is based on conventional mechanical electronics using inclinometers and displacement transducers. The instrumentation system is attached to an operating skip or cage where it functions as a completely self-contained measurement system, operating in conjunction with nor-mal travel of the skip or cage. An on-board tape recorder or a mini-computer with memory can be used to record all telemetry.

Jan 1, 1987

By Theirry Bernard

The era of non-electric systems as an initiating system has revolutionised the blasting world by introducing a very safe initiating system that is reliable, with initiation sequence possibilities that are superior to those of purely pyrotechnical or electric systems. Electronic initiation has brought with it accuracy, programming and controls that were lacking in the non-electric systems. However, it has also led to a certain degree of complexity, which works against user-friendliness, sometimes introducing a few constraints that are balancing out the intrinsic performance of electronic detonators. The introduction of a hybrid initiation system, Electronic and Non Electric, offers accuracy, and flexibility that were lacking in non-electric systems, whilst removing the inherent complexity of electronic systems. This paper endeavours to summarise the advantages and disadvantages of non-electric and electronic initiation systems that have been recorded after years of experience on site. The paper will then describe how a hybrid system only keeps the advantages whilst eradicating the disadvantages, via a case study.

Jan 1, 2007

By A. M. Lovelace

Introduction One area of engineering utilization of materials in which the requirements are especially rigorous and demanding is that of aerospace systems, including aircraft, helicopters, missiles, and space satellites. Materials used in these systems must reliably perform many critical functions in a broad range of adverse environments. Some of the most critical functions are performed by polymeric nonmetallic materials such as elastomers (rubber), coatings, fibrous materials, and reinforced plastics. These types of polymeric materials have some common characteristics that make them attractive to aerospace system designers: light weight, corrosion resistance, and relative ease and low cost of processing and fabrication. Each type also has its own special characteristics that enable it to perform certain required functions better than other competing materials can (Table 1). The desirable properties of polymeric materials, which in some applications make them the only practical candidates, are partly offset by their principal limitation, which is degradation by exposure to high temperature. [ ]

Jan 1, 1971

By Ke Yang

In Chinese coal mines, extraction of deep, highly gassy soft coal seams sandwiched between soft floor and soft roof in complicated geology is commonly encountered. How to safely and efficiently excavate such seams is a very significant and important problem. It has been a focused research area in recent years. By combining the characteristics of fully mechanized longwall mining methods such as large cutting height and mining along the dip, an integrated method and technologies for the Zhangji Coal Mine were developed. This technology includes the design of a complicated geological exploration system, optimization of mining method and working face parameters, control of rock pressure and high levels of gas, reliability model of the production system, and selection and compatibility of equipment. Engineering practice shows that the integrated technology was successful in mining these complicated seams. This study not only enriches the mining method, but also improves the coal mining practice, especially ensuring both safety and productivity under complicated geological conditions.

Jan 1, 2009

Improve the safety, reliability and overall effectiveness of mine stench warning systems and to provide a means of remote control stench injector operation. Approach Industrial gas odorants were analyzed for their suitability for use in mine stench warning systems. A prototype stench injector capable of precise flowrate control was designed, fabricated, and tested using the odorant chosen as having the most favorable properties. Based on the results of the field tests, a second generation injector was developed. The second generation unit features optional remote control operation, and in addition, is simpler to refill and is less expensive than the original injector. A complete second generation system, consisting of two manually operated injectors and one remote controlled injector was in-mine tested through actual mine fire drills. How It Works Ethyl mercaptan mixed with Freon is the predominant stench agent used in the U.S. underground metal and nonmetal mines. However ethyl mercaptan's toxicity,

Jan 1, 1982

By G Ride

The provision of a water supply is a major consideration in planning mining developments particularly in remote areas. The evaluation and development of adequate water supplies in arid areas of Australia is often as important as the discovery of the orebody. The copper orebody at Warrego near Tennant Creek could not be mined economically if cheap treatment water was not available near the mine. This paper describes the difficulties in obtaining water in the Tennant Creek area and the water supply investigations carried out near the Warrego Mine which resulted in the successful discovery and evaluation of a reliable large scale water supply. It is contended that the establishment of a water supply must be approached on a systematic and scientific basis similar to the approach with the exploration and establishment of actual ore reserves. Mining companies with similar water supply problems may benefit by approaching their problem on this basis. The approach adopted by Peko Mines is outlined in this report.

Jan 1, 1971

By K. Becerra, D. G. Almond, T. D. Maru

"Nkomati Nickel Mine in South Africa processes one of the world’s hardest ores in a 375k TPM autogenous grinding circuit. The plant employs an unconventional processing circuit, comprising a primary autogenous mill (AG or FAG) and pebble crushing circuit followed by a secondary hybrid pebble/ball mill and classification cyclone cluster.Advanced Process Control (APC) or Expert Control is now generally accepted as an advantage in most modern high capacity concentrator grinding circuits. This paper reviews the installation of model predictive control at Nkomati and examines the results and benefits of installation in an autogenous mill during plant ramp-up. The paper also demonstrates how predefining process control objectives together with good plant and supplier cooperation can achieve a robust and reliable APC implementation on a very short site program.The results conclusively demonstrate operational and economic benefits during circuit operation with the advanced process control system ON. Production performance and circuit stability were significantly better than during manual control."

Jan 1, 2012

By E. J. White

Data from oil well logs and core analyses were used to quantitatively evaluate formation porosity and water saturation of heterogeneous carbonates and to study the pore geometry and performance characteristics of cores from these formations. Logs and cores from the Madison limestone from 233 wells in three fields in the Williston basin were used in the investigation. A comparison of log and core analyses shows that log porosities are consistently larger than core porosities, and the differences are correlatable with core porosity ranges. Water saturations from logs are usually smaller than the corresponding core saturations by summation of fluids, but the difference is attributable to mud filtrate invasion into the cores during drilling. Petrophysical studies show that the low permeabilities and high residual water saturations in these reservoir rocks are due to their fine crystalline texture and complex pore geometry (heterogeneity). It is concluded that both log and core analyses must be used for reliable evaluation of these carbonate formations.

Jan 1, 1971

By J. T. Sims, C. E. Karayannopoulos

Today's rare earth industry is undergoing significant and rapid evolutionary change toward greater reliability and diversity of supply, increased security of supply chains, and better price forecasting. Technology innovation is reducing rare earth production costs while decreasing the impact of producers on the environment. Advances in rare earth material science are reducing the need for relatively scarce heavy rare earths (HREEs) in high-performance neodymium-iron-boron (NdFeB) permanent rare earth magnets and opening the NdFeB magnetic market space for a broader range of downstream applications. Rare earth producers such as Molycorp are increasingly able to offer long-term supply agreements with forward price predictability, something that has not been the case for many years. All of these trends are helping to restore the confidence of customers and other stakeholders in the rare earth space. That increased confidence is likely to bolster global demand for rare earth materials and expand innovative utilization of these remarkable materials.

Jan 1, 2014

This paper forms part of a series of papers relating to the Melbourne Underground Rail Loop and presented to the Fourth Australian Tunnelling Conference in Melbourne, March 1981. The Design of Electrical and Mechanical Services in Museum Station and adjacent Running Tunnels and their relation to Rail.wruy Operation through the Loop are described. The descriptions, while specific to Muscrio Station, are generally representative of those being provided at Parliament and Flagstaff Stations. The Museum Station comprises some 6500 square metres of platform and track area, 5000 square metres of booking hall concourse and entrances and 1200 square metres of offices and plant rooms. The Mechanical and Ilectrical Services for this complex are .imilar in many aspects to those of a large !.gr.hrise city building, but in general the i::;ign is directed more strongly towards :.arety, durability and reliability, and subject to many restraints imposed by L'mitations of space and accessability.

Jan 1, 1981

"The Garfield plant of the American Smelting & Refining Company is situated about seventeen miles west of Salt Lake City, on the Los Angeles & Salt Lake Railroad, and has freight service by the Denver & Rio Grande Western, Western Pacific and Bingham & Garfield Railways.The site lies between the picturesque Great Salt Lake, with its mountain islands, and the northern point of the Oquirrh Range, which forms the western boundary of the Salt Lake Valley.The location includes several hundred acres of land rising from the southern shore of the lake, selected on account of its adaptability to the economical handling of materials by gravity methods.The smelter is a custom smelter, treating copper ores and concentrates produced in Utah and adjoining states.The ores treated consist mainly of oxides from the Tintic and Park City Districts, sulphides from Bingham District, and concentrates from the mills of the Utah Copper Company, from mills in California, and copper precipitates from the Ohio Copper Company. The last product comes from low grade ores of Bingham Canyon.The following figures represent approximately the daily consumption of materials:Ores and Concentrates…2,700 tonsLime sand…100 ""Coal…350 ""Oil for Roasters…240 Bbls."

Jan 1, 1925