Search Documents

By Motyka J, Adamczyk AF, Witczak S

A case study of migration of a paper factory fluid wastes, on the distance of 5 km from an underground disposal site to an ore mine is presented. The ore mine in question, situated in SW Poland is pumping 3.5 m3/s (ca 300 000 m3/day) of groundwater, producing a cone of depression about 150 m deep and several kilometers wide. The migration of wastes (pollutant) occurs within the carbonate karstic aquifer of Triassic age. The aquifer is about 100m thick and is characterized by the coefficient of hydraulic conductivity equal to 8 m/day on the average. The results of systematic measurements carried out for 13 years enabled to estimate the mean breakthrough curve of the pollutant. On this basis and taking into account the coefficient of hydraulic conductivity as well as the mean hydraulic gradient between the disposal site and the ore mine, the migration parameters of the polluting material, i.e. the real flow velocity, the effective porosity and the longitudinal disper- sivity have been calculated. As the measurements considered a long migration distance of the pollutant, the obtained hydrodynamic dispersion constant (dispersivity), in the authors opinion, is reliable enough to be applied for regional groundwater calculations, regardless of the "scale effect".

Jan 1, 1988

Most coal mines in Chongqing Area are highly gassy mines and liable to outburst of coal cnd methane. In order to harness mine environment and raise the Prodction capacity, methane predrainage is generally taken as a main preventive measure against outburst by all mines. In the recent ten years, the drainage volume per year has increased from 38.25 million m3 to mote than 100 million m3 with a volume over 12 m3 per tome of coal. In some mines, the draining rate is approaching to 50 percent, the rate in mining districts is up to 60 to 70 percent. The predrainage volume accounts for one fourth of total drainage volume. All these have effectively prevented the occurrence of coal and methane outbursts.This is the current situation of methane predrainage in coal mines in Chongqing area, the methods of predrainage to prevent outbursts and related parametres comprise:1. methods, technologies, supervision and effect of predrainage in different geological and mining conditions,2. the change of methane parametres pre-and post-drainage and the analysis of the effect of methane predrainage to prevent outbursts, and3. ways to improve the effect of methane predrainage.Thus the safety, reliability and production of Changqing Coal Mines will be enhanced.

Jan 1, 1991

By W Valery, A Jankovic

The ball mill in closed circuit with hydrocyclones is an industry standard, and well known methodologies exist for equipment sizing, selection and design. However, the potential to improve the capacity of ball mill circuits by replacing cyclones with screens has been recognised for many years and recently has been successfully realised, thanks to developments in fine screening technology. Proper methodology for equipment sizing and selection is required to capitalise on this opportunity, but there is currently insufficient information and few guidelines available on how to design such a circuit. This paper discusses the differences between ball mill circuits closed with cyclones and with screens. A methodology is described for equipment sizing and selection for a circuit closed with screens, and the laboratory testing requirements are described for low grade base metal ores and magnetite ores. An economic evaluation is also presented for a case study demonstrating the potential benefits of closing a ball mill circuit with screens.CITATION:Jankovic, A and Valery, W, 2013. Energy efficient ball mill circuit - Equipment sizing considerations, in Proceedings MetPlant 2013 , pp 285-295 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

At many locations in Australia the decommissioning of mining operations will require the disposal of excess water. If the water is contaminated its disposal may be restricted by government guidelines. The timing of water disposal may be critical to the schedule of close-out. The uncertainty of the annual rainfall input to the water storage and disposal system may determine the success or failure of close-out. The uncertainty associated with any outcome can be used to determine the reliability of the system, or inversely its risk. The technique of Monte Carlo simulation, using the uncertainty in annual rainfall, is applied to quantify the risks associated with water disposal as part of the requirements for close-out in two case studies. In both case studies it is assumed that water disposal is via evaporation only. The first case study is the Nabarlek operation, located about 270 km east of Darwin. This project is required to complete the engineering work associated with its close-out by December 1995. The second study investigates the situation of close-out for the Ranger Uranium Mine, about 250 km east of Darwin. It should be noted that the Ranger mine was examined as part of the annual update of its contingency rehabilitation plan and the probability of implementing the plan is extremely small. The probability of success for the Nabarlek case varied from less than ten per cent to greater than 95 per cent depending on the management strategy. Four possible strategies were investigated for the Ranger mine with the chance of success varying between 20 and 95 per cent. The estimation of the evaporation rate and the area allocated to evaporation was critical in both cases. By applying seasonally based evaporation pan coefficients determined on site, rather than an average monthly value of 0.75, the chance of success was improved by up to 35 per cent for Ranger. Simulation modelling is able to provide information on the likely response of mine water management systems and the level of risk. This information is required to efficiently plan and manage the disposal of water for close-out.

Jan 1, 1994

By Luis Giraldo

Rock bolt installation characteristics near roof falls have been identified as contributing to failure. One documented and regularly occurring failure mechanism is loss of anchorage between the grout and the rock wall of the bolt hole. Key contributors to the integrity of the grout interlocking with the rock mass are the diameter of the hole relative to the diameter of the bolt, resin versus cement type grouts, rock type, and condition of the hole. Smooth bolt holes consistently exhibit less rock bolt load bearing capacity than rough walled holes. The goal of this study was to quantify the benefits of borehole conditioning and develop a systematic approach that would allow improvement of roof bolt performance. A new rock drilling technology, the Helical Drag Bit (HDB), was used in the early stages of this project to condition the borehole. The HDB cuts a prescribed helical groove in the borehole wall. When a bolt is grouted into a hole that has been conditioned using the HDB, the grout fills the helical groove and provides a stronger, more reliable mechanical lock between the rock and the grout. This paper presents results of a series of tests conducted in the laboratory and in the field. Short encapsulation pull out tests have demonstrated considerable increase in pull out strength and more consistent bolt performance when hole geometry is modified using the HDB. The results have also shown that greater load bearing capacity improvements are obtained in mines with weak roof rock, where it is most needed. Additionally, bolts recovered for examination suggest that hole conditioning during roof bolting reduces the effects of finger gloving. Therefore, mines with stronger roof rock could also benefit from hole conditioning. A new roof bolt that uses the HDB principle has been designed and tested. The new system works with existing bolting equipment requiring minimal modifications to the traditional procedure used for installation of fully grouted rebar bolts. The use of these higher anchorage capacity bolts will allow mines to reduce severe injuries and fatalities resulting from ground failures while maintaining or increasing productivity.

Jan 1, 2005

By N. G. Cook, N. C. Joughin, A. J. A. White

The rate of face advance in the gold mines is between 3 and 10 m a month, with a median value of about 5 m a month; it follows that faces are blasted less frequently than is planned. There are many advantages in the use of short holes for stoping to give face advances of from 0,7 to 0,8 m per blast. This has the potential for so increasing the frequency of blasting that monthly rates of face advance could be improved significantly. Cleaning with face scrapers is too slow to permit the maximum achievement of a complete clean, drill, and blast cycle for each shift. Short-hole blasting, combined with the use of mechanical conveyors for face cleaning, offers the possibility of completing two such cycles each day, yielding monthly rates of face advance of up to 35 m. Experiments aimed at developing safe, unitized explosive charges well-suited to produce reliable face advances of 0,7 to 0,8 m per blast under a wide range of gold-mining conditions have been notably successful. A novel method of assessing the effectiveness of a blast based on the percentage of holes that leave socket lengths of 5 cm or less was used. Unitized charges of 60 per cent Ammon gelignite, 600 mm long by 25 mm in diameter, appear to be near optimal. The explosive is de-sensitized to obviate detonation by chance mechanical impact, but requires only a 6D detonator for initiation; it has good water-resistance. Means have been developed for producing these cartridges automatically, but the necessary machines will have to be built specially and the cartridges are not yet available in large numbers. A second experiment by way of an extended pilot production trial using these cartridges in holes 0,9 m long is now under way. Preliminary results indicate that drilling and explosive efficiencies and productivity are well above average, even though face scraping is being used. Unitized charges of this type are likely to prove even more advantageous when mechanical face conveyors come into use.

Jan 1, 1975

In the 1890s, The Goldfields Water Supply Department in Western Australia commissioned the diamond drilling of two deep artesian exploratory water bores near Coolgardie (Blatchford, 1899). At the time, in spite of strongly-worded advice to the contrary from the Government geologists, there was a wide popular belief that you could obtain artesian groundwater virtually anywhere providing you drilled deep enough. The first Coolgardie hole was drilled to over 900 m, despite the fact that the bore penetrated granite from a depth of 5 m below the surface. Drilling proceeded for more than 16 months, between July 1896 and November 1897. A small quantity of salt water was struck at a depth of 36 m. The second bore was mercifully terminated at a depth of 50 m, also in granite, with again only a small inflow of salt water. Such were the desperate lengths that were pursued to obtain a reliable water supply for the influx of people in the Eastern Goldfields gold rush. The WA Goldfields continued to rely on huge condensers for water supply until that great engineering feat, the construction of a water pipeline from Mundaring Weir to Coolgardie, was completed in 1903. An enormous network of rail tracks penetrated outwards from Kalgoorlie and Coolgardie for the collection of timber, principally to feed the condensers. Remnants of the rail network are still visible today. The acute shortage of fresh water led to great deprivation, disease and death among the early miners. Today, the water problems faced by the mining industry are thankfully not as severe, but they are nevertheless no less challenging. The southern part of the WA Goldfields is a notoriously difficult area for finding potable quality groundwater. Even as recently as the 1990s, there were occasional serious efforts to find potable groundwater in that area, some very imaginative and innovative. One mining company, working south of Southern Cross, spent many months experimenting with recovery of potable quality water from a shallow freshwater lens overlying hypersaline water in a low permeability weathered granite aquifer. They used very low capacity pumps manufactured from car windscreen washer pumps powered by solar panels.

Jan 1, 2000

By Peter Heine

Diavik Diamond Mines Inc. (DDMI) has treated systems development as an integral part of the construction project when it built Canada?s second diamond mine. Fully aware that the proper collection and processing of operational data is needed to drive business decisions during production and planning, key Performance Indicators (KPIs) were defined to effectively manage operations when the mine went into production. The Production Information Management System (PIMS) allows KPIs to be measured, reported, and transferred to other systems in a reliable and convenient manner. PIMS provides a mechanism to collect real time production data from the various control systems around the site and acts as a tool to ?drill-down? and establish the important cause-effect relationships that impact the value of a KPI. Thus PIMS provides a data collection, storage, management, and an environment in which cause-effect relationships can be analysed and statistically verified. This understanding of the real cause-effect relationships, close to the source of the data and in the context of the operation, can be used to improve both operations and maintenance performance. The PIMS includes the PI Database implementation, its associated external interfaces with the various Control Systems, Cleaning Packaging Weighing System, Environmental System, Enterprise Asset Management (EAM) System, and Diamond Tracking System (DTS), as well as laboratory data collection, custom applications (downtime tracking, data reconciliation) and user clients. The interface with the EAM system provides material flow quantities and equipment availability on which the plant performance reports are based. The transfer of equipment usage to the EAM system is fed into the maintenance notifications and work orders functionality in the EAM. The environmental system interface provides the mechanism for capturing water consumption data required to generate the various regulatory reports. The interface to the cleaning-packaging-weighing system provides the mechanism for capturing batch data for transfer to the DTS for diamond product tracking at the production splitting facility in Yellowknife. The PIMS lab application provides a means of getting sample data into the system for critical metallurgical metrics, and the data reconciliation application provides a means of manually verifying the data before it is published or passed onto other systems.

May 1, 2003

By S. B. Flagg, J. F. Barkley

In the past few years an awakened activity in power-plant econ- omies has resulted in a marked improvement in the equipment for generating and utilizing steam. Although the improvement in design and construction of steam-driven prime movers has been greater than that of the steam-generating equipment, the economies obtained with the more efficient engines and turbines have stimulated interest and activity in eliminating unnecessary boiler and furnace losses. Much attention has been given to the boiler room in efforts to obtain proper combustion of the coal, because of the importance of the coal item in costs of power production. As evidence of this increasing interest may be cited the record of the development within the past few years of new apparatus for the analysis of flue gases. Many new forms of apparatus have appeared, including those for the determination of carbon dioxide, oxygen, and carbon monoxide, and others for indicating and for recording the content of carbon dioxide only, as carbon dioxide content is usually a good indicator for the control of furnace operation. Because of the large number of steam-power plants operated by the Federal Government and the number of CO, recorders used therein the Bureau of Mines undertook to collect information regard- ing the practical application of such recorders. Articles published from time to time concerning CO, recorders have been mostly descrip- tive, giving little reliable information as to the results that could be expected from the various types of instruments in ordinary prac- tice, and most of the tests made have been of a laboratory nature. Tests of several different types of recorders were made under service and laboratory conditions in order to obtain needed information. The purpose of the Bureau of Mines in publishing the results is to show the factors which may affect the accuracy of a CO, recorder and the manner in which a recorder should be tested. Readers should note that the remarks on different recorders apply to the instruments tested and not to later instruments of the same makers. In the course of the tests the following details were determined: 1. The lag in recording changes of composition of a flowing gas. 2. The accuracy of each type of recorder.

Jan 1, 1916

By P. B. Liebermann

THE resistance to motion offered by mine cars is caused principally by: Rolling friction, flange friction, bending rails, bearing friction and wind resistance. With proper construction and with a fair amount of attention and care, that is, under favorable conditions, the first three items cannot be greatly improved. The wind resistance ordinarily is negligible on account of the slow speeds commonly used. The bearing friction, however, is a variable item, depending upon the design, the bearing material, the lubrication, the location (whether in wheel-hub or on car-body) and the alignment. Under the most favorable conditions the bearing friction will reach a lowest possible value. By the development of a successful anti-friction mine-car bearing this lowest value has been improved to such an extent as to affect the whole system of mine haulage. After being satisfied of their durability and certainty of operation, any investigation into the advantages of anti-friction bearings for mine cars will have to be based upon reliable information as to the saving in power of such bearings. While numerous tests have been made in this direction, the results have not always been convincing, principally because of the rather crude methods that were employed. These crude methods are the main cause of the wide variations existing in regard to the exact amount of the frictional resistance. Frequently an ordinary spring balance is used and the pull necessary to move a certain car or train of cars is obtained by a number of readings. Such spring balances necessarily have a coarse graduation and the continuous vibration and fluctuations to which they are subjected make them highly dependent upon the individual observer. Further, they must be frequently calibrated. Sometimes these tests were made without regard to acceleration, speed or even grade.

Jan 6, 1916

By Glenn A. Gruber

The conditioning of phosphate flotation feed with anionic flotation reagents was identified as a high- priority research topic during a beneficiation work- shop sponsored by the Florida Institute of Phosphate Research (FIPR). FIPR subsequently solicited research proposals to identify the mechanisms of reagent adsorption, to determine scale-up relationships for conditioner design, and to investigate the effect of conditioning variables on reagent adsorption and flotation performance. The two-year research project was awarded to Jacobs Engineering. Somasundaran, Inc., the University of Florida Mineral Resources Research Center, and the U.S. Bureau of Mines assisted Jacobs. Two mechanisms of anionic collector adsorption were detected by spectrographic analyses and confirmed by microcalorimetric measurements. The mechanisms provided a sound technical basis for the empirical practice of conditioning phosphate flotation feed at a high percent solids. Tests performed in laboratory and pilot-scale agitated tanks indicated that power intensity may be used as a reliable scale-up parameter for anionic conditioning of phosphate slurry. Excessive agitator speed during conditioning was found to be detrimental to anionic flotation performance. Some dimensional ratios of anionic conditioners were found to be consistent with good utilization of agitation energy. Laboratory conditioning and flotation tests demonstrated that adsorption of collector onto phosphate and the subsequent recovery of phosphate in anionic flotation were significantly influenced by the quantity and quality of water used in conditioning. Conversely, the quality of water used in flotation was more influential on the recovery of quartz in the concentrate. A comprehensive survey of anionic conditioners and conditioning practice in the Florida phosphate industry was also performed during this project. The study clearly showed that flotation testing with laboratory conditions typical of scientific research gives different results than laboratory testing with simulated plant conditions. The effects of test conditions on laboratory test results should be carefully considered by investigators planning and conducting applied research.

Jan 1, 1999

By John Gross

The study of the energy used in crushing operations has advanced from a period of perplexing confusion to one of greater clarity. Only within the last few years has any true conception of the work in crushing been possible, owing to the chaotic state of theoretical knowledge. For some 20 years a controversy existed between those advocating the Rittinger law and those advocating the Kick law. The Kick law now appears to be definitely out of the picture, and crushing efficiency may be based confidently on the Rittinger theory. There also seems to be a generally crystallized conception as to the meaning and nature of sub-sieve material. There is needed a simple, direct method for determining surface on a crushed ore product, and also a simple and accepted method for size determination on minus 400-mesh material. The Crushing Law The Rittinger(l)‡ theory of crushing was advanced in 1867 and the Kick(3) theory in 1885. While the Rittinger theory might have been accepted without much question and actually had been accepted by many investigators, a serious doubt as to its validity was raised by Stadler(10) who upon purely theoretical grounds proclaimed the Kick "law" as the true law of crushing. According to Rittinger the energy required in successive steps in reduction increases geometrically, while according to Kick the energy increases arithmetically. These "laws" therefore are at variance, and the establishment of the true law was recognized as of first importance. Many simple experiments have been made to demonstrate the application of the Rittinger theory to crushing, and it would seem that its simplicity should favor its acceptance. Experimental evidence, however, was not convincing, as no reliable data could be obtained on the finer material from a crushing or grinding operation. Gates,(13) Bell,(19)

Jan 1, 1935

By C. C. Griggs

From its inception, a limestone quarry or mine should be under the direction of a capable engineer. Before it becomes a reality, he should outlinc the future results, plan the most economical methods for moving the materials and the most efficient equipment, and pilot the undertaking along the narrow pathway of success, avoiding the pitfalls of uneconomical production and the precipitous walls of scanty profits. Inspection of successful limestone properties shows that all have had difficult engineering problems, the solution of which have required keen engineering ability. In approaching a subject of this nature, it is logical to follow the progress of the limestone operation from its inception to the end, as reflecting the engineering required. There are four major divisions: Investigation, equipment, development, and operation. Investigation On the reliability of the engineer's estimates and the soundness of his judgment depend the success or failure of the enterprise. When one visits a prosperous concern, realizes that the limestone is of a constant chemical composition, sees the mechanical devices installed, and watches the output leave the plant in trains of railroad cars or fleets of vessels, he may overlook the fact that in the remote past this great creation was born in some man's brain and evolved through competent engineering. Many factors must be considered before a promoter could procure the money necessary to launch such an enterprise, for a conservative banker will only recommend a successful producer while the promoter must provide funds on his own and his engineer's judgment. An engineering investigation must be made preliminary to expenditure for actual operation, which, for a limestone deposit, would' naturally embrace such subjects as : ' Readily available. 1. Tonnage available........ Possibly available. Chemical analysis.

Jan 1, 1925

By A. Probst, J. A. Finch

"Solids concentration (% solids) profiles and the clear liquid/slurry interface level (mudline) were determined from conductivity measurements in thickeners at Falconbridge' s Strathcona mill (Ni concentrate and non-mag thickeners) and Kidd Creek Division (Cu, Zn concentrates and final tails in the concentrator and thickeners in the Zn plant).The conductivity measurement system consisted of a probe 1.5 m in length with 24 electrode cells, a 24-channel relay, a conductivity meter and a computer. A conductivity profile is collected which locates the mud-line by the sharp change in conductivity. The conductivity measurements are readily converted to solids concentration profiles without need for calibration.The results from the conductivity measurements were compared with those from pressure profiles and direct measurements on local samples obtained using a modified Noranda sampler.It is concluded that the conductivity technique is applicable to locate the mud-line and to estimate the solids concentration profiles in thickeners. This on-line information could improve the operational efficiency of industrial thickeners.INTRODUCTIONAn automated, on-line technique for detecting the clear liquid/slurry interface (or mudline) and the variation in solids concentration with depth would enhance thickener operation and control. In some processes such enhanced control offers significant benefits. For example, in hydrometallurgical operations solid/liquid separation is often the process limiting step. Water treatment plants are increasingly expected to operate remotely and reliable sensing is vital.Current attempts to detect the mud-line include reflection of some signal (e.g. sonar), floats (Dahlstrom, 1985) and measurement of pressure (Rosenblum, 1991), and in one case, natural radioactivity of the solids (Johnston and Simic, 1991). A recent commercial development uses reflection from a vertical array of optical transmitters/sensors, which also gives local solids concentration (BTG Inc., 1991)."

Jan 1, 1993

By Mariana Xavier Milagre

As tensões residuais são geradas, sobre um material em equilíbrio, após a deformação plástica não uniforme causada por cargas mecânicas, térmicas ou mudanças de fase. Falhas estruturais podem ocorrer por uma combinação dos efeitos das tensões de serviço e das tensões residuais o que torna importante a medição e avaliação de como estas afetam as propriedades mecânicas dos materiais. Neste trabalho investigaram-se os valores médios das tensões residuais da fase austenítica de amostras de aço inoxidável duplex UNS S32304 por técnica de difração de raios-x. Acompanhou-se o comportamento do plano 420 com radiação CuKa (?= 1,5419 A ) em difratometro de geometria Bragg-Brentano. As amostras foram tratadas a 600°C com tempos de encharque de 10 minutos, 20 minutos e 8 horas em atmosfera ambiente e resfriamento ao ar e água do mar. Os resultados foram analisados pelo método do sen²? e indicam que as variações microestruturais e térmicas, relacionadas aos diferentes tratamentos, influenciam o valor médio das tensões residuais da fase em estudo.

Aug 8, 2018

By Fergusson E.

An account is given of the history and operation of the Straits Tin market and the Penang price. The procedure by which the official ruling tin price is determined is presented and the way in which bids are treated is outlined: the price declared in Penang is the result of a joint operation by the two Malaysian smelters and is arrived at by finding the highest price at which the whole of the day's offerings for sale can be sold, thus reflecting the marriage of the offerings of the individual mine producers with the demand for Straits Tin from the consuming countries of the world. A system of accurate weighing, sampling and assaying of concentrates delivered to the smelters' premises enables the various ore-buying agencies of the two smelters to notify their central offices promptly of the estimated tin content of the concentrates their customers wish to price that day, so that by 11.00 a.m. both smelters will have exchanged with each other figures giving the total quantity of metal they have for inclusion in the day's market, at the same time exchanging particulars of the bids they have received. Miners are encouraged to sell regularly for cash and an evenness is thus achieved which avoids large daily fluctuations in overall quantity.

Dec 30, 1971

By C. A. Komar

The Bureau of Mines has undertaken an investigation to determine possible applications of acoustic energy at sonic and ultrasonic frequencies to improve ultimate recovery from oil reservoirs. A literature search was conducted to provide background information for initiating laboratory research. The purpose of the literature search was to review the uses that have been made of acoustic energy in the petroleum industry and to select procedures and techniques that could be applied to the solution of petroleum production problems. The characteristics (68)3 of ultrasonic energy make it potentially useful to a variety of industrial and experimental applications. Pulse techniques (99) are common in the testing of materials where inspection is accomplished by propagating an ultrasonic pulse through the material. Viscosity measurements (45) are made by interpreting changes in the absorption of sound as it is propagated through a flowing liquid. Cavitation phenomena (93) produced by high-intensity ultrasound in liquids have been used extensively in industrial cleaning, machining, impact grinding, and aluminum soldering operations.

Jan 1, 1963

By C. R. Austin

In a recent paper1 the authors presented information on a refinement of the Rohn type of creep test with data on pure iron that exemplified the behavior of the apparatus. The present paper extends that work to nickel and cobalt and to the examination of the comparative high-temperature properties of two widely used commercial alloys. Careful attention has been given to the effect of plastic deformation in decreasing creep rate, using the elementary metals iron, nickel and cobalt for purposes of analysis. In any endeavor to develop new materials for high-temperature service one soon encounters a real problem as to the sort of test to be employed in evaluating the commercial possibilities of the alloys. At one time it was considered satisfactory to determine the tensile strengths at elevated temperatures and to use these values as a criterion for the commercial application of the alloys. More recently the proportional limit has been used as a means of classification. Data obtained from a form of bend test have also shown promise as providing a "merit index" of high-temperature serviceability.= Koerber and Pomp3 state that since the influence of testing time is small, the high-temperature yield point of steel furnishes sufficiently reliable and concordant values up to about 350" C. (and a maximum of 450" C. for alloy steels) to serve as a suitable basis for comparison evaluations of materials and for judging permissible stresses. Koerber and Pomp consider, however, that above these temperatures creep limit must be substituted for the high-temperature yield point as the all-important characteristic of the material. Whatever may be their definition of

Jan 1, 1934

By Pollmans GJ, Hoberg H, Schneider FU

The Institute of Mineral Processing at Aachen University of Technology has been engaged in fine and ultrafine comminution for several years. Former investigations had been dealing with the mechanical activation with the aim of increasing the solubility of highly resistant oxides such as tantalite and niobite while research on the product of ultrafine powders is of major importance at the moment. Materials of that kind are of increasing interest in the production of extremely resistant ceramics, in the development of new raw materials, in powder metallurgy and in the production of fillers (extender pigments) and pigments. The creation of ultrafine powders is difficult and very expensive. They can be produced by means of condensation or dispersion methods. One important method of dispersion is mechanical comminution. Due to long and intensive research and development all over the world important advances have been achieved but still a great number of questions and problems occur especially in producing materials of submicron and nanometer grain sizes which could be answered or solved only insufficiently up to now. These mentioned difficulties refer especially to: ò the required energy input into the feed material, ò the forming of strong agglomerates and wall stickings, ò the required product qualities, and ò the entire and reliable characterisation of the products. Basic investigation aim to clarify the micro and macro processes of ultrafine grinding and work towards solutions to the difficulties mentioned above. The aim of the Institute's research is the development of a new grinding device for producing ultrafine powders. First results of a laboratory scale mill of that type will be presented in this paper.

Jan 1, 1993

By O. W. Ellis

RECENTLY there has been a considerable revival of interest in the effects of the various elements commonly added to brass for the purpose of increasing its strength. For many years the work of Guillet2? alone gave reliable information in this regard. Even today his determination's of the coefficients of equivalence of the various elements relative to zinc in brass are those universally employed in industry. This is so because these coefficients have stood the test of time-their substantial correctness has been proved in almost universal practice. It is not our intention to discuss here these coefficients or their use. Rather do we wish to emphasize the need for further systematic studies of the mechanical properties of the ternary systems of copper, zinc, and other individual elements. Since Guillet published the results of his first investigations Millington,16 Smalley33 and Thibaud45 have added somewhat to our information. In general they have confirmed the findings of Guillet, which may be stated in the following rather general terms: 1. The addition of aluminum to the 70:30 and 60:40 brasses progressively increases their hardness and strength and reduces their ductility and resistance to shock. 2. The addition of small amounts of iron to a 60:40 brass improves its strength without affecting its ductility. 3. The addition of small amounts of manganese to a 60:40 brass causes a progressive increase in its strength and reduction in its ductility. A considerable amount of information has been amassed in regard to the effect of nickel on brass (9, 22, 41) which it is unnecessary to refer to here, in view of the scope of this paper.

Jan 1, 1929