Search Documents

By Antonius Prayoga

PT Smelting adopted the Mitsubishi Continuous Technology for its copper smelter plant which has been operating since 1998. Through a series of expansion projects, the plant annual production capacity increased gradually from 200,000 to 300,000 tons of copper. There were no significant modifications for the smelter to reach the 50% additional capacity. It was mostly achieved by intensifying the operation of the furnaces by increasing the oxygen content in the furnaces blowing air. Intensive smelting furnace operation caused shorter campaign life of some furnace refractory, especially the melt zone wall on furnace outlet. During each furnace relining, which is done once every two years, severe wall erosion was found. The worst condition occurred in 2007 when the smelting furnace experienced a melt leak through the eroded wall beneath the bath-line coolers. During the 2008 furnace relining, a modification was performed by installing vertical coolers behind the melt zone wall. Additional vertical coolers were installed during the 2012 furnace relining to extend the coverage area. The modification improved melt zone wall integrity significantly by keeping them safely within the two year campaign life. Recently a modeling study was done to estimate the influences of molten waves on furnace wall erosion. The aim of the study was to predict the impact of blowing parameters, such as blowing air velocity, on the melt wave character and wall erosion.

Jan 1, 2015

By J. M. Stuve

Low-temperature adiabatic heat-capacity determinations were made by the Bureau of Mines in the temperature range from 5 to 300 K for the two crystalline modifications of zinc sulfide, sphalerite (ß) and wurtzite (a). The entropy at 298.15 K of sphalerite was evaluated as l4.02±0.04 cal/deg mole and wurtzite, l4.06±0.04 cal/deg mole.

Jan 1, 1974

By Josef K. Alter

Crosshole Sonic Logging (CSL) of drilled shafts requires 1.5-in (38-mm) or 2-in (51-mm) I.D. sonic access tubes to be installed inside the steel reinforcement cage. The sonic access tubes do not contribute to the structural capacity of the drilled shaft. The proposed use of Ischebeck TITAN T73/56 CSL/Hollow Threaded Rebar for Cross Hole Sonic Logging Access Tubes Combined with Longitudinal Concrete Reinforcing in Drilled Shafts (patent pending) is discussed as an alternative method of construction and CSL probe access. The T73/56 hollow threaded rebar/sonic access tube performs as a high strength rebar while at the same time creating a 2.2-in (56-mm) I.D. sonic access tube. The deformed high strength hollow bar provides better adhesion to concrete thus reducing the problem of debonding associated with smooth PVC and steel pipe. A cost comparison using conventional rebar with added sonic access tubes is discussed. The use of T73/56 CSL/Hollow Threaded Rebar as a value engineering alternative can reduce both material and labor costs for drilled shaft construction and can provide an advantage where anchor bolt cages and longitudinal reinforcing create congestion.

Jan 1, 2011

By M. Gebhardt, J. Johnson, S. Rosenthal

The use of presplitting applications in an underground mine setting is a method of reducing overbreak in the rib and back when blasting occurs. Presplitting performed at the Underground Mine Education Center (UMEC) on Montana Technological University’s campus in Butte, Montana showed a dramatic decrease in the amount of overbreak incurred in the blasting process. Application of the presplitting technique occurred after presplitting presentations at ISEE in San Antonio. Presplit testing consisted of drilling perimeter holes closer together than production holes and loading perimeter holes with a combination of specialized presplit explosive and packaged emulsion with electronic detonator initiation. The ideology was to shoot the perimeter row first, to create a fracture around the perimeter, so when the main production round is shot there is less shock exerted on the surrounding walls due to the pre-fractured perimeter rock. For the test performed, the back ended up with 83% of total holes resulting in half barrels representing a remarkable result. The right rib ended up with one half barrel visible before muck was removed while the left rib did not have any half barrels visible due to a clay seam being in very close vicinity to the perimeter row. The first test blast was a great start encouraging future work on presplitting applications in the UMEC. Additional testing will continue with different combinations of perimeter hole spacing, the addition of a buffer row along the ribs, and varying loading techniques to determine the most effective presplit method for the rock type of the UMEC. Detailed test results and loading configurations will be provided in the paper.

Jan 1, 2024

By AIME AIME

THE 1944 Chairman of the Institute of Metals Division might be classed as metallurgically ambidextrous ; he is teacher of theory and practice of both nonferrous and ferrous metallurgy, and he is consultant on brass and on highspred steel. Arthur Phillips was born in Troy N.Y. and attended the New Haven Connecticut high school. Upon graduation he entered Yale, receiving a degree in metallurgy in 1913. At that time Professor Mathewson was starting his plan of '"co-operation with the metal industries in metallographic work at the Hammond Laboratory of the Sheffield Scientific School, Yale University, and Arthur Phillip, became the first co-operative graduate student, working in the laboratory of the Bridgeport Brass Co., and receiving his Masters of Science degree in 1915. A little later, when the department of metallurgy at Yale was expanded. Me. Phillips was appointed assistant professor. In 1928 he was made associate professor, and in 1934 he was promoted to full professor.

Jan 1, 1944

By Manqiu Xu, Peter Wells, Gord Bacon

"A methodology is proposed for milling flowsheet design using flotation rate, selectivity and residence time distribution data. The flotation rate data and the difference in flotation rates between the main minerals to be separated are determined from laboratory batch tests. The residence time distribution (RTD) data is calculated using the tanks-in-series model assuming each flotation cell is a perfect reactor. The rate, selectivity and RTD data can be used to calculate the optimum flotation cell number in a bank for rougher/scavenger in a commercial plant.This methodology is demonstrated in a case study of a nickel sulfide ore. It is shown that miniplant rougher/scavenger data can be closely predicted from a batch test using the proposed methodology.INTRODUCTIONIt has been the trend in the past several decades that large flotation cells are increasingly used. This is largely driven by the economics as ore grades are getting lower and the rate of ore processing must be increased in order to keep mining operations economically viable. The development and evaluation of 250 to 500 m3 WEMCO SmartCell and Outokumpu TankCell flotation machines are well in progress. There are many advantages in using large cells: fewer cells, less floor space, lower power cost (although this is now being questioned for fine particle flotation), simpler circuit, simpler control, and lower auxiliary equipment cost (Arbiter, 1999). As flotation cells are getting larger, the importance of cell hydrodynamics, namely, air/slurry dispersion, power intensity, froth transfer, residence time distribution (RTD) and short-circuiting are being fully recognized (Jonaitis, 1999; Weber, et al., 1999; Gomez and Finch, 2002). It is not the intention of this paper to discuss flotation cell scale-up. The intention is to answer what is the optimum number and size of cells in a flotation bank for a given throughput. Figure 1 illustrates this problem facing design engineers. The same mean residence time required for a given throughput can be achieved in a single large cell, or many smaller cells in a row. A few cells of large size may be more cost-effective but they may not be as effective as more cells of smaller size in achieving the optimum metallurgy."

Jan 1, 2005

By H. K. Lin

The effect of metallic iron fines on froth flotation of a sulfide ore was examined by comparing the flotation results with and without iron fines present in the flotation feed. Mild steel and ceramic laboratory ball mills were used to grind 600 g sulfide ore charges. The mild steel ball mill generated approximately 4.6 g of iron fines (0.8% of the ore charge mass) when grinding to a product size of 80% passing 200 mesh (75 mm). When a low dosage of a weak xanthate collector was used in flotation, the impact of the iron fines on sulfide flotation was marked. Higher dosages of stronger xanthate collectors rendered the impact of the iron fines much less significant. Consumption of the collectors by the powdery iron fines is believed to cause the differences observed in the flotation results. A galvanic effect on flotation was not evident in this study. The impact of the iron fines on silicates depression was also examined.

Jan 1, 2008

By Ralph K. Foster

During five underground mine fires which occurred in Arizona during 1980 and 1981, sealing the fire area became necessary. To minimize leakage into the fire area, ventilation control measures were instituted to balance pressure across the bulkheads. Problems en- countered in sealing the fire areas and measures taken to improve these conditions are discussed. The routing of the ventilation and ventilation control to en- sure the workers' safety were also important considerations in reopening the mines. The use of continuous CO monitors is discussed. One important consideration was the condition of the fire, and chromatographic analysis was used to establish this. Graphs comparing the Trickett ratio, carbon monoxide, carbon dioxide, and oxygen concentrations are given. The Trickett ratio was useful but needed to be augmented by the comparison of CO, C02, and 02. Problems with getting good samples from sealed areas and recommended procedures that were developed during these fires are discussed.

Jan 1, 1982

By Dena Morgan, Emre Biringen

"Abstract This paper discusses the execution of pile installation and design issues at two environmentally challenging industrial sites in North America. Environmental regulations set constraints on the design and require versatility in choice of technology.For a proposed bridge, due to protected fish habitat, performing soil borings within 30 m of the creek embankment was prohibited. The limited subsurface profile indicated a thick upper layer of granular material, thus driving H-piles was considered. However, to limit generation of vibration and noise in the protected area, drilled piles had to be used. During execution, the subsurface profile differed from that in the borings 30 m away. Very soft, saturated silt was encountered at the bottom of the caisson and the length had to be redesigned very quickly while the contractor waited for instruction. For a new structure in uncontrolled fill area, performing soil borings was not allowed. It was known that a layer of peat was present in the area, but no information regarding the thickness and extent. The subsurface profile generally consisted of granular material overlying a thick compressible silt layer. Somewhere within the granular layer peat would likely be encountered. Franki piles were chosen to penetrate the peat and bear in the underlying granular material. During environmental sampling in the area, methane gas was encountered and Franki piles were no longer a viable option due to safety concerns. The foundation system was changed to steel H-piles driven to bedrock, which was more than 50 m below the ground surface and sloping. Rock shoes that would work to significant slopes had to be used in order to increase the likelihood of good embedment within the bedrock. Also, due to obstruction of an approximately 3 m thick debris field that was encountered in the upper granular soils, some of the piles had to be relocated and extra piling needed to compensate for such differences. The results of PDA testing to estimate compressive capacity and a series of lateral load tests are presented.INTRODUCTIONThe design issues that are encountered during construction can be quite problematic and have a significant impact on schedule. In order to avoid such impact on the project, a thorough subsurface investigation should be considered prior to design and construction. Better understanding of environmental regulations also prevents costly changes to the foundation design. This paper discusses the execution of pile installation and the design issues at two environmentally challenging sites in North America.BRIDGEDuring the subsurface investigation for a proposed industrial building complex, several boreholes were drilled within the footprint or in close proximity of various structures, with Standard Penetration (SPT) sampling of the upper coarse-grained soils (sand/gravel) and undisturbed sampling of the lower fine-grained soils (silt/clay). The SPT blow counts (N60) were corrected by a factor of 1.35 in order to incorporate the SPT automatic energy transfer ratio. When Modified California Sampler was used, a correction factor of 0.44 to 0.64 was also applied. N60 values were further corrected for gravel to avoid artificially high blow counts during the analyses due to spoon samples contact with gravel and cobbles, and the corrected values of (NG)60 (limited to a maximum value of 50 blows/300 mm) were used for design. The information from the SPT boreholes was then used to assess the subsurface conditions beneath the structures, as well as for a nearby bridge that was designed to cross over a creek. Since performing soil borings within 30 m of the creek embankment was prohibited due to the protected fish habitat, the investigation with regard to the bridge abutments was limited to two deep boreholes (B10-33 and B10-34) at the bridge location and two additional boreholes (B10-35 and B10- 36) located approximately 200 m upstream. The bridge location and two sets of boreholes are"

Jan 1, 2014

By S. J. Neethling

"Flotation is a complex process with many factors that influence the performance of a cell. This paper examines the impact of several key variables on the performance of flotation cells. The study makes use of a simulator for the froth phase of the flotation vessel, as the main purpose of this study is to separate the impact of different variables from one another.In experiments it is very difficult to separate the effect of variables from one another as a change in a singe input parameter, such as air rate, invariably also affects many of the other key variables, such as bubble size and bubble bursting rates. This interaction between variables makes it very hard to experimentally separate the impact of, for instance, the air rate from that of bubble size or bursting rate. In the simulator, though, it easy to make independent changes to these variables.In order to achieve this a base case simulation that is typical of many of the rougher cells found in sulphide flotation circuits was carried out. Four key variables, air rate, incoming bubble size, surface bubble size and the fraction of the bubbles flowing out of the cell unburst, were varied in order to obtain the system’s response.The most significant results were obtained when the bubble size was varied. An increase in the incoming bubble size has the effect of reducing the pulp zone recovery, but increases the froth zone recovery. If it were possible to vary the incoming bubble size without influencing the overflowing bubble size, the impact of the change would be unclear because of these two competing effects. The effect of a change in the overflowing bubble size has an opposite effect on the froth recovery, with larger bubbles resulting in lower froth recoveries."

Jan 1, 2003

By Gilbert Francklyn

The requirements of coals for the manufacture of coal gas, water gas and producer gas will be considered sparately and a short description of each gasmaking process will be given. In this report the term "gas coal" is confined to coals suitable for the manufacture of city gas in horizontal, inclined or vertical retorts. The report does not refer to coke-oven practice.' Briefly, the process of manufacture consists of distilling the coal at high temperature in an externally heated retort out of contact with the air. The products of distillation, consisting of gas, tar, ammonia, etc. are collected and purified. The residue consists of coke, which is removed from the retort at the end of the carbonizing period. To supply the heat required in the process, a portion of the coke produced is converted into producer gas, which is burned under the retort settings. Qualities of Gas Coals The chief qualities that coal must possess in order to be classified as a gas coal are as follows: 1. Gas Yield.—The coal must be capable of yielding gas in sufficient volume and of a satisfactory quality. The yield depends considerably upon the temperature of distillation; a higher temperature will give a larger yield of gas, but the qualit,y of gas (now measured by the British thermal units per cubic foot) will be lower, while a lower carbonizing temperature will give less gas of higher heating value. The true measure of the yield is the number of British thermal units produced in the gas from a given quantity of coal. This number is obtained by multiplying the cubic feet of gas from 1 lb. of coal by the British thermal units per cubic foot of gas; it is called B.t.u. feet per pound. It is found that the

Jan 1, 1930

By Wilbur C. Helt, Joseph J. Yancik

Throughout the history of mankind, the principal use of coal has been to produce heat through combustion. The heat is used in many ways: to warm air space for our comfort; to provide heat or energy to power industrial processes, such as cement and steel production; and to produce electricity. Because it is our nation's most abundant fossil energy fuel, coal in the late 20th century is on the threshold of becoming a significant source for synthetic liquids and gas energy fuels for this country. This is made possible by conversion processes which can change solid coal into various synthetic gases and liquids. These coal-derived fuels are nearly identical to the processed fuels and chemicals provided by natural gas and crude oils, which presently provide almost all the petrochemical feedstocks and energy fuels needed for the residential, light commercial, and transportation markets. A revolution is beginning to take place, not only in the United States, but in many other countries with a return to a coal-based energy economy. Also, new combustion and conversion technologies which are compatible with national health arid environmental goals are rapidly emerging. These technologies will allow coal's use to be expanded not only in its traditional markets, but also to supply markets held by natural gas and crude oil. With the worldwide decline in natural gas and crude oil reserves, coal is being looked upon to meet the energy demand. Because of these new coal conversion technologies, coal will no longer be only a combustion fuel, but a valuable raw material for production of a variety of clean fuels and chemicals. MARKETS FOR COAL: PAST AND FUTURE A simplified diagram of the marketing network for coal is shown in Fig. 1. As shown in this figure, coal is transported to its traditional

Jan 1, 1981

By Edmund S. Davenport

The production of thorium of high purity by the Ca-CaCl2 reduction has been described by Marden and Rentschler,1 who also reported some of the properties of the coherent, ductile metal obtained from this pure thorium powder. The present paper describes the properties of thorium produced by the Ca-CaCl2 process modified in some details to meet commercial conditions. The principal effect of these changes in process has been an unavoidable increase in the oxide content of the thorium. Materials and Methods The thorium employed in this investigation was made from pure thorium oxide (ThO2) by the Ca-CaCl2 reduction. The washed and dried metal powder was pressed into bars approximately 0.160 in. dia. and 10 in. long, at a pressure of 75,000 Ib. per sq. in. The bars were heat-treated in vacuum at 1175' C. for 1 hr. This treatment yielded ingots sufficiently dense and coherent for mechanical working. Thorium has been successfully worked without a protective metallic covering, but for the purposes of this investigation it was more convenient to inclose the ingots in soft iron tubes and swage or roll cold to the desired sizes. The iron sheath was dissolved with nitric acid, leaving the cold-worked thorium exposed. Chemical Analyses Analyses of typical samples of the material used in this work arc given in Table 1. Thorium powder oxidizes in moist air, even at room temperature; no unusual precautions were taken to prevent such oxidation of the material used in this investigation. A certain amount of oxidation probably takes place during pressing; certainly during heat-treating unless a very slow heating schedule is employed. These factors account

Jan 1, 1930

By Wilbur C. Helt, Joseph J. Yancik

Throughout the history of mankind, the principal use of coal has been to produce heat through combustion. The heat is used in many ways: to warm air space for our comfort; to provide heat or energy to power industrial processes, such as cement and steel production ; and to produce electricity. Because it is our nation's most abundant fossil energy fuel, coal in the late 20th century is on the threshold of becoming a significant source for synthetic liquids and gas energy fuels for this country. This is made possible by conversion processes which can change solid coal into various synthetic gases and liquids. These coal-derived fuels are nearly identical to the processed fuels and chemicals provided by natural gas and crude oils, which presently provide almost all the petrochemical feedstocks and energy fuels needed for the residential, light commercial, and transportation markets. A revolution is beginning to take place, not only in the United States, but in many other countries with a return to a coal-based energy economy. Also, new combustion and conversion technologies which are compatible with national health and environmental goals are rapidly emerging. These technologies will allow coal's use to be expanded not only in its traditional markets, but also to supply markets held by natural gas and crude oil. With the worldwide decline in natural gas and crude oil reserves, coal is being looked upon to meet the energy demand. Because of these new coal conversion technologies, coal will no longer be only a combustion fuel, but a valuable raw material for production of a variety of clean fuels and chemicals. MARKETS FOR COAL: PAST AND FUTURE A simplified diagram of the marketing network for coal is shown in Fig. 1. As shown in this figure, coal is transported to its traditional

Jan 1, 1981

By D. Lauzon, H. de Ruiter

"In 1988a decision was taken to design and install a computerized mine monitoring and control system. This system had to monitor and control all pumping and ventilation underground. The operation of the mine air heating, using waste heat from the mine water and compressors, was to be part of the system. It ultimately also had to interface with the four existing Canadian General Electric Series 3 PLC's which controlled the No .3 shaft loading pockets. Beside operational control and trouble shooting, the system is a valuable tool in energy management and ultimate savings are estimated at $50,000 per year.The final equipment selection was a General Electric Series Six PLC on surface with a total of 17 Series One Plus and Juniors PLC located underground. Data is transferred through a two-pair shielded cable using modems. Both analog and digital functions are being utilized.The basic monitoring and control system was commissioned during 1989and, due to a higher level of technology today, further improvements have been planned for the future. The system was designed by Walter Dow together with Gordon Champion of D.G. Champion Engineering Ltd. of Toronto. Advice for the ventilation part of the project was obtained from Maurice White, Independent Ventilation Consultant.The Ministry of Energy, Mines and Resources and the Ministry of Energy of Ontario approved this project together with the waste heat recovery project to qualify for a grant of$135,000 under the Enerdemo-Canada program.IntroductionThe Macassa mine is a narrow vein gold mine situated about 2 km west of the town of Kirkland Lake in northeast Ontario. The mine has been in continuous operation since 1933 and a total of about 3.0 million ounces have been recovered out of 6.6 million tons of ore ."

Jan 1, 1991

By L. V. Bell

THE object in prospecting is to find ore. With the exception of certain discoveries of more or less accidental nature, intelligent prospecting as conducted today is, whether consciously or not, based upon a process of elimination. In the following discuss on it is proposed to evaluate those factors that enter into the eliminating of certain tracts of ground and, conyersely, the concentrating of attention upon others. The danger of generalizations as to the barrenness of cer.ain areas, without having due regard for all such factors, is emphasized. The fact that our conception as to what areas or rock formations are to be regarded as favourable or unfavourable is, in some measure at least, changing with new discoveries under diverse and unexpected circumstances, adds more point to the discussion. The criticism might be raised that the subject is treated largely from the standpoint of geology, but that may be met by stating that it is, and must continue to remain, precisely from this standpoint that the prospecror directs his activities. Briefly, the geologist may render the greatest service to the prospector in the early steps of selecting (a) the general territory in which to prospect; (b) the area to be intensively prospected; and, finally, (c) those parts of the claim or claims to be prospected in detail. Although certain phases of the discussion will be, in some measure, of general application, we shall here concern ourselves essentially with prospecting in the pre-Cambrian shield. Furthermore, the subject is so large that it has been decided to limit it to a consideration of that portion of the pre-Cambrian rocks in which is situated the mining district of western Quebec, of which the writer can speak with more personal knowledge. This limitation need not, however, seriously detract from whatever merit the discussion may possess, since the deposits concerned cover a fairly wide range of metallic ores, including gold, copper with associated zinc, and, lastly, molybdenum.

Jan 1, 1936

By R Millar

A frequent challenge in mine water management and mine design is estimation of precipitation and extreme rainfall given a short record of site meteorological data. For remote mine projects, typically only a few years of rainfall data are available, which is far too short for estimation of design rainfall event, such as the 1-in-100 year storm. A frequency-paired approach is presented for comparing daily precipitation records from a mine site with a long-term regional station and provides the basis to transpose the long-term record to the mine site. This allows a long-term synthetic precipitation record to be developed for the mine site that can be used to undertake site water balance studies, determine pond storage requirements, assess water supply options and address other surface water management issues. Conventional approaches are based on chronologically-paired data and when applied to daily data generally yield poor correlations between stations. In the frequency-pairing approach, statistical distributions (two-parameter gamma distribution) are fit to daily data from two stations and used to calculate daily and extreme precipitation values for the short-term site (which is typically a mine or other project site). The method is demonstrated using data from two meteorological stations located along the south coast of British Columbia, Canada. Use of a fitted two-parameter gamma distribution (or other distribution) provides a sound theoretical approach to comparing precipitation data from two sites and the basis for transposing a long-term record to generate synthetic precipitation series and extreme rainfall values at mine sites.CITATION:Millar, R, 2013. A statistical approach for deriving project design rainfall, in Proceedings Water in Mining 2013 , pp 273-276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Dale Preece, Steven Case, Cassidy McAllister

Simplot Phosphates produces high quality phosphate fertilizer through open pit mining. The operation near Vernal, UT began as a three-pass mining process carried out with drill and blast followed by the combined effort of shovel-truck and dozer material removal. The first two passes removed the overburden and the final pass mined the relatively hard phosphate ore for processing at the mill. Vertical blastholes were employed in all of the mining passes.

Jan 1, 2012

By Ralph L. Rutherford

Geologists or mining engineers familiar with geology are frequently requested by mine operators to give correlation in-formation regarding some mining property with respect to an adjacent area on one at some greater distance. It is the object of this article to mention a few of the difficulties involved in securing this information and to point out some of the salient factors upon which correlation is dependent. In view of the nature of the following discussion, a brief statement of the general character of coal formations .. seems appropriate. Coal formations, by reason of their environment of deposition which is in fresh or brackish water, exhibit the features common to continental deposits, in contrast to those of marine deposits. Such deposits are characterized by rapid variation in thickness and in lithological character both later-ally and vertically. (Plate 1 A). They consist essentially of sandstones and clay shales with all gradations between them, and also a few beds of coal and frequently some conglomerates.

Jan 1, 1924

By Martin H. Stanczyk

Freezing to dewater typical Florida phosphate rock slime as demonstrated in laboratory tests appeared to have potential commercial use because of indicated moderate energy requirements, good compaction of dewatered solids, and effective recovery of usable water. After freezing, thawing, decanting, and filtering, batch freezing of gallon-size 13.7 percent solids slime samples yielded 42 percent solids products. Cationic amine, used as a process additive, yielded 46.8 percent solids product with significant filter area reduction. Semicontinuous 8 stage freezing tests also produced thickened slimes. Cooling and freezing 13.7 percent solids slime from 30° to minus 10° C required removal of 183 Btu per pound of slime; Carnot cycle calculation indicated that the theoretical minimum energy to transfer this heat was 27.8 Btu per pound. To produce 1 ton of 44 percent solids slime from 13.7 percent sol-ids slime, the calculated theoretical energy required for cooling and freezing was 52.3 kilowatt-hours. During the research heat capacity and heat of fusion data were determined for the slime at various percent solids.

Jan 1, 1971