Search Documents

By G. R. Hopkins, E. M. SEELEY

The number of natural-gasoline plants has shown a consistent decline in recent years, but the total capacity has increased steadily. The number of completed plants, as determined by a survey as of January 1, 1932, amounted to 959. Previous surveys of January 1, 1928 and 1930 showed 1,155 and 1,035 plants, respectively. Of the total plants on January 1, 1932, 859 were operating and 100 were shut down, compared with 999 operating and 36 shut down on January 1, 1930. The material gain in the number of inoperative plants in the last two years was probably due to the severe decline in prices of 1931. The low prices of 1931, which were approximately 40 per cent below 1930, made it virtually impossible for the majority of the independent plants, or plants not owned by a large integrated company, to operate at a profit. Accordingly, the majority of the plants removed from the list in 1930 and 1931 were owned by companies which were engaged solely in the manufacture of natural gasoline. The total daily capacity of the plants on January 1, 1932, amounted to 11,387,000 gallons, an increase of 871,000 gallons, or 8 per cent, in the two years 1930 and 1931. That the total capacity of the plants has increased while the number of plants has declined is due to the fact that nearly all the plants constructed in the last five years have been large plants. During 1931 the average total daily capacity of the operating plants was approximately 10,600,000 gallons, while the average daily production amounted to 4,944,000 gallons. This indicates that the plants operated during 1931 at 47 per cent of their capacity, compared with 58 per cent in 1930 and 61 per cent in 1929. Although more plants have been dismantled in Oklahoma in recent years than in any other State, it continues to rank first in number of plants. On January 1, 1932, there were 238 plants in Oklahoma, compared with 145 plants

Jun 1, 1932

By P. Trueman

A project is underway to convert a validated methodology to a system that will permit the near real time interpretation of loading data from longwall powered supports, allowing rapid adaptation of mining strategies, maintenance scheduling and set pressures for optimal roof control. Such a system has the potential to significantly reduce roof control problems and is a pre-requisite to successfully fully automating a longwall face. The development depended upon a robust methodology for interpreting the pressure sensor data coming from the face in the context of support strata interaction using a novel characteristic load cycle analysis concept. New software was developed capable of handling the large quantity of data emanating from a modern longwall with the current level of signal corruption and loss, accurately delineating load cycles and extracting the critical load cycle features essential for interpreting how the support and strata are interacting. Existing software being used to access the pressure data were found either to be incapable of delineating load cycles at all or, where they could, the accuracy was low, making it impractical to use them in combination with the new advances in load cycle analysis. The software is currently being extended from ?off line? to ?on line? in order to provide a real time response to changing strata conditions.

Jan 1, 2006

By Gabriel Plascencia

Copper was oxidized in the temperature range from 300 to 1000 GC under different pressures of oxygen. In the range from 300 to 500°C, copper oxidizes following the logarithmic rate law; while in the range from 600 to 1000°C oxidation follows the parabolic rate law. Transition from logarithmic to parabolic growth occurs at about 525°C. X-ray diffraction was performed on oxide scales to account for the CuO/Cu2O ratio at different temperatures. Activation energies found in this work are in good agreement with reported values.

Jan 1, 2003

Inn mining communities throughout the western United States, cows have always been part of the landscape as they graze on surrounding rangelands. Until recently, mining companies regarded these animals as something to be kept off their properties — especially any freshly reclaimed lands. During the last few years, though, this situation has begun to change. Today, cattle can be seen in a handful of mine settings, moving up and down the slopes of mine tailings and waste rock. These animals are being used by several companies to do some of the reclamation work once performed by large earth-moving equipment, mechanical spreaders, rippers and seed drillers. This is because cows can contour slopes more naturally and produce and spread soil nutrients in ways that tractors and ripping machines cannot.

Jan 1, 1999

By Samuel Canchaya M.

El presente trabajo señala los diferentes métodos geoestadísticos utilizados en la industría minera. Por ello, las aplicaciones de la geoestadística abarcan todas las fases de un proyecto minero que va desde la prospección hasta el tratamiento metalúrgico. Asimismo, los métodos geoestadísticos por su rigidez matemática, objetividad y eficiencia varias veces demostrada, pueden desplazar a los métodos tradicionales, cuyos errores e inexactitudes fueron poco advertidos en el pasado, debido a la bonanza y relativa accesibilidad de los depósitos minerales.

May 1, 1984

By William J. Robinson

What is the cumulative rate of recovery of copper from a sulfide leach dump? The technical answers to this frequently asked question may vary from "I don't know" to "quite good" from people of the same company. Management also poses this question because it plays a vital role in planning future production. The answer is difficult because of the many variables between different operations such as physical construction of the dump, topography of the original site, characteristics of dump material, mineralization, and water application. Each of these factors and others have a bearing on the rate of recovery. Anaconda's method of water distribution at Butte is unique in that each dump is drilled to allow physical injection of water into the dump. The injection holes are drilled vertically on 25-ft centers from the surface of the dump [(Figs. 1 and 2)]. Normally, the holes are drilled 40 ft deep and cased with 4-in. PVC perforated pipe. The pipe is perforated at 1-ft intervals with four 1 -in.-diam holes at 90° spacing on the pipe circumference. Formerly, shallow holes (20-40 ft) were alternated with deep holes (80-180 ft) in an effort to cover the entire dump and hasten oxidation. The shallow hole depth varied according to the compaction thickness. The deep hole depth varied according to the height of the dump and the original ground profile. It is preferable to have the deep holes end 20-30 ft above the original ground level. This generally allows penetration of the coarse material at the bottom of the dump. Deep holes had to be discontinued in order to cover more

Jan 1, 1974

By S. P. Sandoval

The U.S. Bureau of Mines investigated the separation of aluminum from copper dump leaching liquors using a supported liquid membrane. Aluminum was selectively transported through porous polypropylene impregnated with di (2-ethylhexyl) phosphoric acid in an aliphatic diluent. The effects of variables, such as solution composition, temperature, and extractant concentration, were measured with a three-level fractional factorial experimental design. Experimental results were used to derive equations for predicting transport rates for aluminum, iron, and copper. The major variables influencing aluminum transport were solution temperature, feed solution pH, aluminum concentration in the feed solution, and extractant concentration. Copper and iron transport rates were almost zero when aluminum transport rates were high. Measured aluminum transport rates under the best conditions of 55° C, pH 3.0, 16 g/L A13+, and 65 pct extractant solution confIrmed the predicted value of 210 f.'g/(cm2.h). Transport rates for iron and copper were less than 5 ug/(cm2.h) under these conditions. Aluminum was recovered from the stripping solutions by sparging with gaseous hydrogen chloride to crystallize aluminum chloride hexahydrate, which was calcined to alumina. Sparging crystallization regenerated the stripping acid for recycle.

Jan 1, 1989

By D. R. Pyke, R. S. Middleton

"Three main types of base metal sulphide mineralization are present in the Timmins area:(1) -Massive and stringer-type copper-zinc deposits occurring mainly in pyroclastic rocks, as typified by the mines of Kam-Kotia, Jameland and Canadian Jamieson, or within or close to possible breccia pipes as shown by the Genex and Kidd Creek mines. With the exception of the Kidd Creek mine, all of these orebodies occur northwest of Timmins (Kamiskotia area) and appear to lie within or close to a major center of volcanic activity characterized by a thick accumulation of felsic pyroclastic rocks and subordinate epizonal intrusions. The margins of the rhyolitic pile are interfingered with mafic volcanics; overlying sedi-ments mark the termination of a vol-canic cycle. The copper-zinc deposits in the Kamiskotia area are confined to a particular stratigraphic unit. Ore-bearing solutions were probably derived from the intrusive complex of the volcanic pile.(2) -Porphyry copper deposit of the Mcintyre mine. The deposit occurs in a quarz porphyry intrusion related to the volcanism in the area (Hurst, 1936). Mineralization was probably introduced at the time of intrusion, and subsequently redistributed within the porphyry during deformation. (3) -Massive and disseminated nickel mineralization, associated with serpentinized alpine-type ultramafic intrusions, as shown by the Alexo, McWatters, Hart, Inco and Texmont deposits. The nickel mineralization occurs at or near contacts of the serpentinites with felsic or mafic volcanics, or sulphide-bearing iron formations. The nickel deposits south of Timmins are confined to a particular stratigraphic unit along the margins of domical-shaped structures which appear to outline former volcanic centers. Sulphurization as pro-posed by Naldrett (1966) appears to be a workable hypothesis for the formation of some of the deposits."

Jan 1, 1971

By Hiroshi Ono

"By newly developed ICP method, trace amounts of As(III), As(V) .,Sb(III) and Sb(V) were precisely determined within accuracy of sub ng/ml. As(III) and Sb(III) were separated from As(V) and Sb(V) by extracting into ·xylene as diethyldithiocarbamate complexes using diethylammonium diethyldithiocarbamate (DDDC), and then back-extracted into nitric acid for a quantitative determiruition by ICP-AES equipped with hydridegeneration system The recoveries of As(III) and Sb(III) were satisfactory throughout the extraction with 0.04mol/l DDDC in xylene from lmol/l hydrochloric acid solution and the back-extraction with 7 mol/l nitric acid. As(V) and Sb(V) were reduced to As(III) and Sb(III) by ascorbic acid and potassium iodide, and their quantities were determined as mentioned above. The detection limits were found to be 0.58ng/ml for As(III), 0.63ng/ml for Sb(III) using 50ml of a sample. The proposed method was applied to analysis of the real sample.Introduction In drain, arsenic(AS) concentration is prescribed below 0.lmg/l, so As must be removed. As is existed at .the form of As(III) or As(V) in solution. For t1Jeir difference of chemic;µ property, it is not easy to remove As in solution. So it is an urgent necessity to develop for determining concentration of As(III) and As(V). Antimony( Sb) has resemblance .chemical property to As. So Sb was experimented the same as As.The separation and determination of As(III) and As(V) have been carried out using several methods, such as ICP after copreclpitating separation, HPLC, direct hydride generation atomic absorption. However these methods have some problems. One of main problems is that HPLC and direct hydride generation atomic absorption methods are influenced by coexisting elements."

Jan 1, 2000

By Sean Gallagher

Background. There is currently little information regarding factors associated with specific modes of motion segment failure using a fatigue failure model. Methods. Thirty-six human lumbar motion segments were fatigue tested using spinal compressive and shear loads that simulated lifting a 9 kg weight in three torso flexion angles (0°, 22.5°, and 45°). Twenty-five segments failed via fatigue prior to the 10,000 cycle maximum. These specimens were visually inspected and dissected so that the mode(s) of failure could be determined. Failure modes included endplate fractures (classified into nine varieties), vertebral body fractures, and/or zygapophysial joint disruption. Logistic regression analyses were performed to determine whether certain morphometric variables, amount of motion segment flexion, disk degeneration scores, and/or loading characteristics were associated with the occurrence of specific failure modes. Findings. Results indicated that stellate endplate fractures were associated with increased posterior shear forces (P < 0.05) and less degenerated discs (P < 0.01). Fractures running laterally across the endplate were associated with motion segments having larger volumes (P < 0.01). Endplate depression was more common in smaller specimens (P < 0.01), as well as those experiencing increased posterior shear force (P < 0.05). Zygapophysial joint damage was more likely to occur in a neutral posture (P < 0.01). Interpretation. These results suggest that prediction of failure modes (e.g., specific endplate fracture patterns) may be possible (at least for older specimens) given knowledge of the spinal loads along with certain characteristics of the lumbar spine. Published by Elsevier Ltd. Keywords: Lumbar spine; Endplate fractures; Zygapophysial joints; Morphometry; Disk degeneration; Motion segments; Aging

Jan 1, 2006

By S. D. A. Hannot, H. Knapp

"High pressure grinding rolls (HPGR’s) are an energy efficient solution for comminution of industrial minerals and metal ores. The technology is successfully applied in an expanding field of applications throughout the minerals industry. HPGR’s compress and grind the particle bed in the operating gap between two counter-rotating rolls. The equipment provides a high capacity, low energy alternative for applications with conventional tertiary and quaternary crushing and grinding, with size reduction reaching from 100mm down to 25 microns product. In this process, maintaining a controlled and evenly distributed operating pressure between the rolls is very important. Due to feed segregation, the pressure distribution along the roll’s length can become uneven, resulting in a coarser product. This paper will show that the best approach to compensate and adapt for the uneven pressure is to allow the rolls to skew relative to each other. Coarser products are also caused by an inadequate pressure distribution: the much-discussed edge effect. To minimise the consequence of the edge effect, an optimised ratio for the roll length to diameter will be calculated. Furthermore, the design philosophy behind a cheek plate will be detailed. This cheek plate is used to retain the material between the rolls, reducing the edge effect while still allowing roll skew. Together these design considerations help optimise HPGR’s performance.INTRODUCTION Initially developed for the cement industry during the energy crisis in the 1980’s , high pressure grinding has been an accepted technology for many years. It has been successfully implemented throughout the minerals industry, with applications in base and precious metals, as well as industrial minerals processing. The comminution process relies mainly on size reduction through to compression and inter-particle crushing in a particle bed in the operating gap between two counter-rotating rolls. The equipment typically has a high unit capacity and low energy consumption, and is increasingly used as an alternative to conventional tertiary and quaternary crushing and grinding, in particle size ranges reaching from 100mm down to 25 microns. It can be applied to moist ores and dry material, in open circuit arrangement or in a closed circuit with dry or wet classification (screening, air classification)."

Jan 1, 2019

By C Thompson, D Connelly

The history of mill liners has evolved over time and this paper tracks the changes and development of liner technology. It provides an overview of the primary types of liners, the design and the materials of construction. The design of a mill liner is driven by application, materials of construction, casting technology and handling issues. The choice of solid steel, grid liners, rubber or composites and magnetic liners is based on many factors.The methods used for monitoring wear and predicting eventual change out time are many and varied. The contribution of discrete element modeling (DEM) analysis in predicting wear profile is discussed.Mill trajectory and DEM software programs are used with great effect to predict the effect of lifter height, face angle, high low lifters or mill speed. In the field, trial and operational experience is used or improvements/design concepts at one operation are applied to another. Broken mill lifters, accentuated wear and other problems can be better understood using hardness testing, chemical analysis and photo micrograph analysis of pearlitic or martensitic structure along with fracture face observations. This forms a part of the typical root cause analysis. However given correct and sound liner and lifter, feed and discharge design media selection, and materials of construction, the majority of premature liner or bolting failure is normally attributed to incorrect operational methods such as excessive high ball to feed ratio, incorrect mill speed relating to lifter ball throw, incorrect media selection, "tramp" material entering the mill charge from upstream or recirculating process and understanding the specific mill operation in question.It is hoped that this paper will benefit mill operators who are faced with challenges of improving wear life and at the same time optimizing mill throughput and performance.CITATION:Connelly, D and Thompson, C, 2013. The selection design and application of mill liners for large wet grinding mills, in Proceedings MetPlant 2013 , pp 133-140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Wilson Bardales

El presente trabajo describe la experiencia de la Gestión de la Calidad en la Cía. Minera Poderosa S.A., específicamente en el rol que desempeñan los Círculos de Mejoramiento Continuo (CMC´s) como un vehículo efectivo para alcanzar los objetivos de la empresa. Los CMC´s están integrados por trabajadores de un mismo proceso, a quienes se capacita en el manejo de herramientas, técnicas y metodologías de la calidad, con la finalidad de realizar mejoras en los procesos. En ese sentido, en la compañía minera La Poderosa, la administración es participativa y el directorio difunde las políticas, para lograr la rentabilidad de la empresa. Así también, los mandos medios definen los objetivos y estrategias, desplegándola en cascada a la supervisión y estos a su vez, al personal de línea. Este concatenamiento de responsabilidades y la participación de los CMC´s aseguran el alineamiento y control de la gestión.

Sep 12, 2005

By J W. Simmons, T H. Antoun

"Rock fragmentation is an important component of explosive mining and excavation techniques andis the culmination of a damage accumulation process dominated by crack propagation. During the past 20 years, improved computer modeling of this process has resulted in new and promising computational tools for improving explosive mining and excavation procedures. This paper discusses one of these new computational tools, a computer model called BFRACT."

Jan 1, 1995

By G. B. SOUTHWARD

MECHANIZATION is being developed to some extent in every coal field in the United States and it is rather difficult to say which State or section of the country has made the greatest advancement. Statistics now being compiled for 1928 will show the tonnage mined, the amount of equipment used in each of the coal-producing States, and the comparative tonnages and percentages of total tonnage mined in each of these States, and will reveal which field is making the greatest advancement as far as quantity of production is concerned. However, while the tonnage figures are of great importance there-are other phases of coal-mine mechanization, such as the types of equipment, the mining methods and coal bed conditions, which are of equal interest. The change from hand-mining practices in all of the various operations from the face to the railroad cars is, perhaps, more indicative than any other one thing of the real progress being made.

Jan 1, 1929

By HeeDong Lee, Owen Reedy, Lawrence Matson, Naidu Seetala, Thomas Key

Spark Plasma Sintering (SPS) consolidated ZrB2+SiC composites using nano-powders (around 40 nm) showed smaller grains compared to those using micron size powders and segregation of SiC into islands is minimal but with higher oxidation of ZrB2 to form ZrO2 in nano-composites. Argon-gas purging prior to SPS consolidation at around 2000 °C and 40 MPa of ZrB2+20vol.%SiC nano-powders was used to minimize the oxidation and obtain fine granules with high densification. The densification of the Argon-gas purged nano-composites is higher compared to those consolidated without Argon gas purging. The EDX analysis showed a strong reduction in the oxygen peak for the Argon gas purged composites. The XRD spectra also support this observation with less ZrO2 phase composition in Argon gas purged composites. The Vickers micro-hardness showed slightly lower values for Argon gas purged composites though they have higher densification.

Mar 1, 2017

By Hayward B. Oblad

The effects of eight independent variables on froth flotation product yield, ash content, and coal recovery were studied using laboratory batch flotation of 0.6 am x 0 coal. The eight flotation variables investigated were air feed rate, pre-dispersion of collector oil, impeller speed, product collection time, initial solids concentration, collector conditioning time, frother (methyl isobutyl carbinol) concentration, and collector (No. 2 fuel oil) dosage. The two-level Plackett-Burman screening design and the three-level Box-Behnken design were used. Within the ranges studied, air feed rate had no effect on product yield. Pre-dispersion of collector oil, impeller speed, product collection time, initial solids concentration, and collector conditioning time showed only minor effects on the product yield and quality. Frother concentration (mg/L) in the process water and collector oil dosage (g/kg) were shown to be the dominant independent variables in coal froth flotation. Flotation experiments that vary initial solids concentration at constant frother dosage (g/kg) confound the effects of frother concentration (mg/L) and solids concentration. The dominating effects of frother concentration and oil dosage on coal recovery and froth product ash content are illustrated with three-dimensional plots. The relationship between froth product ash and coal recovery is also clearly illustrated by the flotation data.

Jan 1, 1985

By Andrew Dobson

The assessment and control of environmental noise from mines has become increasingly important in recent years, due to urbanization and population growth, increased regulation of environmental factors, and overall awareness and sensitivities to noise exposure.&nbsp;Minimizing adverse effects on communities and achieving compliance with local ordinances is now commonplace, and consideration of noise during the design and/or operation of a mine cannot be ignored. Ventilation equipment can represent the loudest and most bothersome equpiment at mines, however there are complexities when attempting to control the assocaited noise, due to the acoustical nature of&nbsp;mine vent fans. In fact, the utilization of traditional and/or&nbsp;industry standard methods can intensify&nbsp;the noise impact, or simply not work as intended. This paper provides recommendations on specific noise control methods that are suitable for mine ventilation equipment, based on recent assessment work and field experience.

Oct 1, 2024

By Stefan Stein, Jorge Davo, Adrian Villanueva, Abhay Kulkarni, Shane Hoff

Pellet sizing plays a key role in the productivity of the entire pelletization and subsequent induration processes, whereas uneven pellet sizing can increase the circulating load of the balling circuit inducing operational instability leading to production loses. The present work focuses in comparing the agglomeration kinetics, expressed as the number of pellets produced in a determined target size range, of different organic binder-bentonite binder systems. The batch experimental results show that the binder system has a great influence in the resulting pellet sizing, which could lead to advantages in terms of balling circuit efficiency and eventually operational de-bottlenecking.

Oct 1, 2019

By B. Q. Li, R. A. Mirshams

"A numerical algorithm is described for the simultaneous prediction of the thermomechanical behavior of the materials and microstructure evolption during metal forging. The numerical development is based on the finite element solution of the thermoviscoplastic deformation of metals coupled with the internal state variable model describing the microstructure evolution involving work hardening, recovery, recrystallization and grain size distribution. The finite element code for rigid viscoplastic deformation is developed based on the modification of the existing code for the thermal and fluid flow calculations. The code is tested against and compares well with the results reported in literature. The procedures for the integration of the · rnicrostructure model into the macro finite element model are described. Results are presented showing the characteristics of materials dynamics and mechanical deformation during simple metal forging processes.IntroductionIn industrial deformation processes such as hot rolling and forging, the workpiece undergoes both macroscopic plastic deformations and microstructural evolution. A computer model that allows to predict both materials dynamics and macroscopic deformation is obviously more useful for both fundamental understanding and deformation process optimization. For some industrial applications, especially those involving novel, light and high strength materials, such an integrated model is critical in that both materials and thermomechanical 'behavior during forging must be carefully controlled to obtain the products that meet the desired strength requirement [I]."

Jan 1, 2000