Search Documents

A new technology for the treatment of copper nickel-containing concentrate after high-grade matte flotation to blister copper with the production of liquid silicate slags in a vertical autogenous unit with upper oxygen blow has been considered. The copper and nickel behavior in the process of sulphide copper concentrate interaction with silicate melt containing oxide copper has been studied. The general mechanisms of such interaction are found.

Jan 1, 2003

By Toshia Ishii, Jun Kubota, Noriko Kubo

"For steel continuous castings, it is essential to control molten steel velocity at the meniscus, since the velocity is closely related to surface defects on the resultant products. Argon gas is supplied with molten steel into the mold through the submerged entry nozzle to prevent nozzle clogging. In this study, to investigate the influence of argon gas on molten steel flow, a numerical simulation was carried out by a two-phase model. Simulation results indicate that as argon gas bubbles ascend near the nozzle by their buoyancy, they induce the molten steel flow with them and resulted a meniscus molten steel flow from the nozzle to the narrow face of the mold. This flow direction is opposite to the case without argon gas. The calculated data are compared with the experimental data. The comparison shows generally good agreement between the measured and the calculated data. IntroductionIn a steelmaking process, molten steel carried by a ladle is first fed into a buffer vessel called tundish. From the tundish, it is then fed into a continuous casting mold. Molten steel solidifies gradually in the mold (the primary cooling zone) forming a solidified shell. As the solidified shell is just thick enough to support the molten steel at the mold exit, it is withdrawn through the mold by pinch rolls. It is progressively thicken as it is further cooled with water sprays in the secondary cooling zone. At the end of guide roll zone, completely solidified steel is cut into desirable lengths. Schematic view of a typical continuous casting is shown in Figure 1."

Jan 1, 1999

By A. Spearing

According to a 2000 NIOSH report, about 100 million rock anchors are installed annually in coal mines in the USA. Most coal mines have conditions that are conducive to corrosion of the rock anchor and ancillaries (such as plates), yet the effect of this on the performance of the anchors has not been adequately researched and its effects are not understood or quantified in the USA. There is considerable research into corrosion in civil engineering applications on surface and underground but the corrosion of coal mine rock anchors is not necessarily the same because: ? In underground civil structures, water ingress is usually stopped as part of the construction process. ? Many rock bolts in mines are only partially resin grouted leaving part of the reinforcing member exposed to corrosive conditions. All cable bolts in coal mines are only partially resin grouted. ? Even when mine bolts are fully grouted, shrinkage cracks occur and the rock stresses can change due to adjacent mining that can cause the resin column around the bolt to fracture further under external shear or tensile stresses. Most coal mines therefore have ideal conditions for bolt corrosion.

Jan 1, 2010

By Nathanael Wagner Sales Morais

Os aços maraging tem grande importância tecnológica devido sua aplicação nas industrias aeroespacial e nuclear. Uma das aplicações para esse material é a fabricação de cilindros de alta resistência pelo processo de estampagem profunda, logo o conhecimento da textura cristalográfica torna-se fundamental. Este trabalho investigou o efeito da laminação à frio seguida por um recozimento sobre a microestrutura, textura e anisotropia plástica no aço maraging 350. A anisotropia foi medida pelo cálculo dos coeficientes de Lankford e dos coeficientes de anisotropia normal (Rm) e planar (?R). Os resultados mostraram o aumento na deformação a frio gera um aumento na intensidade da fibra acompanhada de um aumento no valor de Rm. As análises metalográficas mostram que maiores reduções induzem à um precipitação intermetálica após o recozimento.

Aug 8, 2018

By Guan-Yong SHI, Cong Wang, Zhi-he DOU, Ting-an ZHANG, Shi-gang FAN

Based on the pre-works, this paper proposed a new short stage process of the intensify aluminothermy reduction by the stage to prepare high titanium ferroalloy with low O and Al contents. We investigated the effects of Al and Ca and Si combination reduction agent, slag type and step-up reduction conditions on the Al content and distribution in the alloy. The results show that the step-up reduction can not only reduce effectively the oxygen content in the alloy, but also reduce effectively Al content. For instance, the oxygen content in high titanium ferroalloy is within 1%~4%, and the Al content is within 1%~5%. Its quality reaches the requirement of high titanium ferroalloy prepared by remelting process.

Jan 1, 2015

By Adriano Alex de Almeida

Dois aços de grão não orientado com 2,45 e 3,3 %Si com 7 amostras para cada liga, foram estudados para compreensão do efeito do teor de silício nas perdas histeréticas. As amostras foram recozidas com diferentes temperaturas de recozimento final, resultando em diferentes tamanhos de grão. As perdas histeréticas e B50 foram medidos. Os resultados de B50 mostraram que não houve variação de textura entre as ligas com diferentes %Si. Por fim, os resultados não mostraram variações da energia dissipada pela perda histerética com adição de %Si.

Aug 7, 2018

By AIME AIME

A COMMITTEE of the American Railroad Association, consisting of Samuel Rea, president of the Pennsylvania System, Chairman; F. D. Underwood, president of the Erie Railroad; A. T. Dice, president of the Philadelphia & Reading Railroad; E. J. Pearson, president of the New York, New Haven & Hartford Railroad; and C. H. Markham, president of the Illinois Railroad (who was represented at the meeting by J. F. Porterfield of his system), met at the headquarters of the American Institute of Mining and Metallurgical Engineers, New York, on April 6 to assist in the Coal and Coke Committee's attempt to solve the bituminous coal problem. There was a full discussion of the questions of seasonal freight rates and the purchase by the railroads during the slack months of their winter's supply of coal. As the question of fuel supply for the railroads is in the hands of the Railroad Association, as well as the coal operators, it was vital that it should be represented at this important conference. The situation from the point of view of the mine operators was presented very thoroughly. No seasonal rates were considered necessary for the year 1920, and, as this matter requires considerable thought, it will be given thorough study and worked out in detail at a subsequent meeting.

Jan 1, 1920

By C. Pichler, A. Ressler, D. Gregurek, A. Spanring

In order to improve the refractory lining life at one of the RHI key customer test procedures were developed within a two years collaboration project. In the first year of cooperation detailed refractory corrosion work in the rotary kiln with Ca-ferritic slag was performed. The main results of the second year of cooperation, reported in this article, involve a detailed testing work with nickel matte and pre-selected refractory brands which was performed in TBRC. A first part of this work was a complete chemical and mineralogical characterization as well as FactSage calculations carried out on provided matte samples. According to these results testing in the TBRC was realized at different process temperatures with several magnesia-chromite bricks. Based on the mineralogical investigation a high chemothermal load caused by sulfidic matte resulted in a deep reaching infiltration of the brick microstructure and partly corrosion of main brick components.

Jan 1, 2015

By Maurício Covcevich Bagatini, Maycon Athayde

Water consumption reduction in pellet feed operation is of paramount importance. Compared with traditional ball mills, high-pressure grinding rolls (HPGR) play an important role in Blaine surface area (BSA) generation to improve agglomeration properties, although stability is still a challenge. Grindability improvement of existing operation has a direct impact on the performance of the filtering and pelletizing operation. The results of this study, as a pregrinding operation, can be applied not only in new operations but also in existing ones, helping the operator control process variation in a more effective way while ore hardness increases. 

By Mustapha A. Raji, Alafara A. Baba, Kuranga I. Ayinla, Misitura Lawal, Abdul G. F. Alabi, Aishat Y. Abdulkareem, Rafiu B. Bale, Folahan A. Adekola, Muhammed O. Muhammed

Increasing demands for pure wolframite ore in the form of ammonium paratungstate (APT), tungsten oxide cannot be over emphasized. Thus, treatment of a Nigerian wolframite ore containing admixtures of scheelite (CaWO4: 96-900-9631) and stolzite (PbWO4: 96-900-9813) by hydrometallurgical route was investigated in hydrochloric acid chelated with phosphoric acid to extract tungsten via solvent extraction. During leaching, parameters such as leachant concentration, chelate dosage and reaction temperature on ore dissolution were examined. At optimal conditions (1.5 mol/L HCl + 2.0 mol/L H3PO4 solution; 75 °C), 95.0% of the initial 10 g/L ore reacted within 120 min. The derived activation energy of 56.80 kJ/mol supported the proposed dissolution mechanism. The unreacted product analyzed by XRD was found to contain siliceous impurities. Tungsten recovery from leachate was carried out by solvent extraction with Aliquat 336 in kerosene. Pure tungsten was recovered as APT and beneficiated to produce high grade industrial tungsten oxide of industrial values.

Mar 1, 2018

By E. Mongilardi

The construction of large underground openings through cohesionless or weak cohesive soils and under the water table in particular, often requires a ground improvement to be done from the surface or ahead of the excavation face in tunnelling problems. To this purpose various injection procedures have been used in the past and new outstanding techniques have been developed recently, such as "jet-grouting", extending the feasibility range. The paper presents a review of basic principles and practical design criteria with particular reference to the newest trends of development. Case histories have been selected within the experience of specialist contractor Rodio Co. showing the variety of problems solved by manifold grouting procedures and layouts, in widely different soils ranging from the sandy-gravelly alluvia of Milan to the soft marine clays of Singapore.

Jan 1, 2010

By K. Goshtasbi

In this paper a genetic algorithm is used in a heavily jointed rock mass in order to investigate the critical circular slip surface and modification of slope surface. This method was applied to the southern wall of the 6th Golbini Jajarm bauxite mine. The mine is the largest bauxite deposit in Iran, located to the northeast of the town of Jajarm in the Khorasan province. Estimated reserve of bauxite in this deposit is about 160 million tonnes. Field and laboratory investigations were conducted in order to determine rock mass behaviour. A genetic algorithm code that uses the Simplified Bishop method as an objective function was developed for findingt he safety factor of circular slip surfaces. Sensitivity analysis was applied to determine the optimum values of the genetic algorithm variables, such as population size, selection method, crossover and mutation rates. After finding the critical circular slip surface, slope modification is carried out by removing unstable sections from marked critical slip surfaces, and this process is repeated until the last unsafe section is removed. Based on this code, modification occurred during 7 steps, by reaching a safety factor of 1.3 in the last step. Finally, the modified slope angle of the southern wall of the 6th Golbini Jajarm bauxite mine was determined to be 48.44 degrees. Keywords: Genetic algorithm, slope modification, circular slips surface, 6th Golbini Jajarm bauxite mine .

Jan 1, 2008

By Nien-Yin Chang

The contemporary seismic response analysis of structures using a finite element analysis code requires six elastic spring constants to address the six degrees of freedom ground/foundation contribution to the response of a structure to earthquake shaking. However, the ground response is nothing but linear. Thus, it is critical to address the effect of the nonlinear ground response to the performance of structures under strong earthquakes. This study specifically addresses the effect of pile foundation on building vibration using finite element analyses. The effect of single pile was first investigated and the load was applied at the pile head using the single-degree-of-freedom load at a time, including three translational loads in the x, y and z directions and three moment loads about the three respective axes. In this study, the coupling effects between two or more different loads were not investigated. A load is increased monotonically to investigate the nonlinear behavior of pile under various loads. The Mohr-Coulomb model was used to represent concrete. To explore the effect of soil models on the nonlinear spring functions, the following constitutive models of soils were used: linear elastic, Mohr-Coulomb model, Cap model, modified Cam-Clay model, and Duncan-Chang hyperbolic model.

Jan 1, 2007

Map

Jan 1, 1941

Improvement of Phosphate Ore Flotation Performance Through Sized Flotation

Sep 13, 2010

By Raja V. Ramani, Robert L. Frantz

"In response to the U.S. Bureau of Mines (USBM) Request for Proposal (RFP) for "" the establishment of a Generic Mineral Technology Center (GTC) in Respirable Dust,"" the Mining and Mineral Resources Research Institutes (MRIs) at The Pennsylvania State University (PSU) and West Virginia University (WVU) in association with participating MRIs at Massachusetts Institute of Technology (MIT), and the University of Minnesota (UMN) have prepared the comprehensive research program described herein. Michigan Technological University (MTU) joined the Center as an affiliate after its inception. This program was developed with recognition of the stated objective of the Federal Mine Safety and Health laws which is to "". . . permit each miner the opportunity to work underground during the period of his entire adult working life without incurring any disability from pneumoconiosis or any other occupation-related disease . . . .""Exposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic consequences and some others, slow and long enduring, has been a major concern for labor, management and the government. This concern has manifested itself in four mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of mines according to the best recommended practices, (3) interaction of dust and lung control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workman's compensation laws for occupation related health deterioration."

Aug 31, 1989

By S. L. Bessinger

In the design and specification of a ventilation system for an underground mine, it is necessary to make reasonably accurate estimates of the pressure losses in the various airways of the mine. These estimates can be made with little difficulty for open airways with simple geometric cross-sections, such as those cut by continuous miners or tunnel-boring machines. The situation is much different on a longwall face, where the airway's complex geometric cross-section and the presence in the airway of obstructing equipment having a variety of shapes make it difficult, if not impossible, to estimate pressure loss using traditional methods of calculation. Headlosses in mine entries are calculated using Atkinson's Equation (1). [H = (English) H = (SI) (1)] where H = pressure ,loss, in. of H20 (Pa) K = friction factor, lbf min2/ft"4(Kg/m3) P = perimeter, ft. (m) L = airway length, ft (m) Q = airflow quantity, ft3/min (m3/sec) A = flow cross sectional area, ft2 (m2)

Jan 1, 1987

By Enrique Munaretti, Vitor Rosenhaim, Jair Carlos Koppe, Joao Francisco Feijo

The B3 mine is a multiple coal seam strip mining in operation in Rio Grande do Sul, the southernmost state in Brazil. A traditional truck & excavator operation is used to remove the overburden and selectively mine coal seams, ranging in thickness from 30 cm (1 ft) to 2.5 m (8.2 ft). Blasting is required in order to excavate part of the sedimentary rock overburden where the rock is too hard for mechanical excavation, and to mine the coal seams, selectively.

Jan 1, 2012

By W. L. Dalmijn

The processing of scrap and scrap cars starts with size reduction by a hammermill, or shredder. After the liberation the magnetic fraction is removed. The remaining non¬magnetic fraction mixed with other materials is screened and each fraction is processed separately. The increased use of plastic has a negative effect on the recovery of metals and waste production. At Huron Valley, Belleville Michigen, USA, the non-ferrous fraction from 5 million obsolete cars per year, containing 200,000 tons of non-ferrous metal, is processed. Aluminium Is recovered with a heavy medium separation process and concentrated with eddy current separators. The remaining heavy non-ferrous fraction is concentrated by a new combination of eddy current separation and image processing. After this separation process the zinc fraction is melted and refined and the copper, brass, stainless steel and other high-quality concentrates are sold to the secondary industries. The recycling of car scrap has become an important source of metals and materials for the secondary. materials processing industry.

Jan 1, 1995

Tunnelling under squeezing ground conditions poses significant challenges. There are fundamental differences in the choice of support for mining as opposed to civil engineering. This paper reviews ground support strategies that have been used to control large deformations in mining excavations based on field data from five different mines in Australia and Canada. Recommendations are made for improved ground control strategies in squeezing rock conditions.

Jan 1, 2008