Search Documents

By J. Trckova, P. Prochazka

Physical models from equivalent materials satisfying geometrical and physical similarity have been constructed. A special technology of simulating the excavation of an opening at the front part of a tunnel and of measuring the deformation at the tunnel face was applied. The results yielded by the physical models were used to formulate constitution relations in the numerical solution. This coupled modelling enables us to predict the behaviour of tunnel structures more accurately. On a construit des modèles physiques, réalisés en matériaux équivalents et répondant aux conditions de ressemblance géométrique et physique. Sur ces modèles, on a utilisé une technologie intéressante de simulation du forage du tunnel et de la mesure de déformation du front de taille pendant le forage en progression. Les résultats donnés par les modèles physiques ont été utilisés pour formuler les relations de constitution dans la solution numérique. Une telle construction de modèles combinés permet de prévoir plus précisément le comportement de la structure du tunnel. Es wurden physikalische Simulierungsmodelle aus äquivalenten Werkstoffen konstruiert, welche die Bedingungen der geometrischen und physikalischen Ähnlichkeiten erfüllen. Bei diesen Modellen hat man die interessante Simulationstechnologie des Tunnelvortriebs sowie die Verformungsmessung beim Tunnelabbaustoß während des Vortriebsvorgangs eingesetzt. Die Ergebnisse der physikalischen Simulation wurden zur Formulierung von Konstitutionsrelationen in der numerischen Lösung genützt. So eine kombinierte Simulation erlaubt eine genauere Prognose des Benehmens der Tunnelstruktur.

Jan 1, 2003

By C. A. Rowland

Introduction Rod mills are horizontal, cylindrical, rotating, tumbling mills in which steel rods, that are usually about 6 in. shorter than the length of the grinding chamber, are used for grinding media. Fig. 33 shows a cutaway view of a rod mill. Rod mills were first used around 1910 because of their ability to grind in open circuit, consistently produce a uniformly sized prod¬uct, give greater continuous availability, and give lower maintenance costs. They have basically replaced roll crushers and coarse grinding ball mills in comminution flowsheets. The present 20-ft limit on rod length, based on rod manufacturing methods, and the pulp flow char¬acteristics, that influence mill capacity, have established the maximum rod mill sizes' of 15 x 21 Vs ft using 20-ft rods and drawing from 2,200 to 2,300 hp. Rod Mill Uses. The principal uses for rod mills are: preparing feed for ball or pebble mills, grinding gravel or aggregates to the size analysis required for making concrete sand, preparing coarse agitator feed for leaching operations, and for primary grinding circuits, particularly in industrial mineral applications. Wet grinding is the most frequently used grinding process for rod milling. There are a few special cases where dry rod milling is used. Preparing feed for ball or pebble mills is the most common use for rod mills. In ferrous and nonferrous ore concentrators, wet open-circuit grinding is used to prepare ball-mill feed. Figs. 34 thru 37 show the four basic grinding circuits used in these concentrators. In rod mill-ball mill grinding circuits, where the rod-mill discharge contains 25% or more of the grinding circuit product-size material, the rod-mill discharge can be fed to the ball- or pebble-mill classifier as shown in Fig. 34. This is the most frequently used rod mill-ball mill circuit in the nonferrous ore concentrators. In a few concentrators such as Anaconda's Weed concentrator,55 the rod mill discharges to one classification stage which makes the same or a slightly coarser particle-size cut as the classifiers used to close the ball- or pebble¬mill circuits, as shown in Fig. 35. In concentrators where rod mill-ball mill circuits are used to grind low grade magnetic iron ores such as Reserve Mining Co., Silver Bay, Minn.; Erie Mining Co., Hoyt Lakes, Minn.; Eveleth Taconite Co., Forbes, Minn.; US Steel, Mt. Iron, Minn. and Atlantic City, Wyo.; Inland Steel-Jackson County Iron Co., Black River Falls, Wis.; and The Cleveland-Cliffs Iron Co., Adams mine, Kirkland Lake, Ont., the rod mills discharge to rougher magnetic separators (cobbers), the concentrates from which are fed to a ball milling stage as shown in Fig. 36. The same basic circuit is also used with gravity concentra¬tion methods such as spirals (Hanna Mining Co., Groveland, Mich.), tables (St. Joe Minerals, Bonne Terre, Mo.), and jigs. When the rod-mill discharge contains less than 25% of the grind¬ing circuit product size, this indicates an ore that does not readily produce the fines needed to help carry the coarse feed into the ball charge. When this occurs, the fines in the rod-mill discharge are needed in the ball mill or pebble mill so the rod-mill discharge flows direct to the second-stage mills as shown in Fig. 37. Rod mills are used to make feed for open-circuit ball mills such as those used in wet grinding cement raw material (American Cement, Brennan Ave¬nue plant, Detroit, Mich., and Port Huron, Mich., plant, and at the South Dakota State Cement plant, Rapid City, S. Dak.). Grinding gravel or aggregates to the size analysis required for making concrete sand is used in areas where natural sand of the proper particle size gradation required to make concrete is not availa¬ble. Three-quarter inch crushed aggregate is ground to 4 mesh using center peripheral-discharge rod mills (Fig. 38) operating in open circuit. US Corps of Engineers specifications state that the sand product be 93-100% passing 4 mesh and contain no more than 3-7% passing 200 mesh. It may be necessary to classify the rod-mill discharge to remove any excess -200 mesh sand produced in the rod mill. Particu¬larly when processing aggregate with high abrasion indices, center peripheral-discharge rod mills are used instead of hammer mills, fine bowl crushers, and crushing rolls for the production of specification sand. If the -4 mesh size fraction of the rod-mill feed is removed

Jan 1, 1985

By C. H. Stockwell

THE Eastern Townships of Quebec have been the chief Canadian source of chromite. Production, however, has never been large and, except for a period of steady but small output between 1894 and 1909, mining has been active only in war time. The known deposits are too small or too low grade to compete with overseas sources in normal times. During the last war, shipping difficulties and a greatly increased demand in the United States resulted in high prices and a ready market for low-.grade material. The Quebec chromite industry flourished and played an important part in relieving the wartime shortage. Shipments in 1918 .amounted to 15,600 tons of crude ore and 6,400 tons of concentrates. At the outbreak of the present war it was natural to turn again to the Quebec field as a possible source of this strategic mineral. Some of the old properties have since been opened by private and government money and some new deposits have been found. Total mill capacity is 750 tons per day, as compared with 200 to 300 tons in 1918. During 1940, 1941, and 1942, about 85 chromite deposits were examined by the Geological Survey in a belt 100 miles long and up to 7 miles wide. A part of this belt, about 35 miles long, in which the geological features ?were not well known, was mapped on a scale of 1/2; mile to an inch.? Small ..areas around some of the deposits were mapped in detail, on scales of 20 to 200 feet to an inch. Some geophysical work was done but did not result in the discovery of ore. Prospecting by stripping and trenching was then undertaken and chromite ore was uncovered at several localities. The above work was done by the writer and by J. W. Ambrose, who has kindly contributed his results for incorporation in this paper. Y. O. Fortier actd as assistant in the geological work and, in 1942, was in charge of a sub-party engaged in geological mapping. The author is indebted to H. C. Cooke and J. W. Ambrose for reading the original manuscript and for offering many helpful suggestions for its improvement.

Jan 1, 1944

By R. S. Dean

The brief resume of the activities of the Metallurgical Division that appears annually in its progress reports series serves a useful purpose by making available a rather comprehensive but concise recapitulation of the current work, and publications of the division. An unprecedented opportunity to attack the problem of producing ferro-grade material from low-grade domestic manganese ores effectively was provided by the act designated as Public 667 of the 76th Congress of the United States, approved June 26, 1940, which made available an appropriation for "Expediting Production of Equipment and. Supplies for National Defense." Although the funds were not immediately available to the division, good progress has been made in the, solution of the many and diverse problems presented in the studies undertaken to determine the best methods for the recovery of useful products from a wide variety of manganese ores.

Jan 1, 1941

By Graeme J. Jameson

A form of column flotation cell is described in which the contact between the feed and the air stream is made in a mixing device at the top of a vertical downcomer. The air-liquid mixture flows downward to discharge into a shallow pool of pulp in the bottom of a short cylindrical column. The bubbles disengage and rise to the top of the column to overflow into a concentrate launder, while the tails are discharged from the bottom of the vessel. The main advantages of the device described are that the overall height of the column is reduced to about one metre (3 ft), and the column can be self-inducing with respect to the air supply. Experimental results are given from tests on a feed stream to a conventional zinc cleaner circuit. Using wash-water to reduce gangue entrainment, the column gave high concentrate grades and high recoveries.

Jan 1, 1988

A form of column flotation cell is described in which the contact between the feed and the air stream is made in a mixing device at the top of a vertical downcomer. The air-liquid mixture flows downward to discharge into a shallow pool of pulp in the bottom of a short cylindrical column. The bubbles disengage and rise to the top of the column to overflow into a concentrate launder, while the tails are discharged from the bottom of the vessel. The main advantages of the device described are that the overall height of the column is reduced to about 1 m (3 ft), and the column can be self-inducing with respect to the air supply. Experimental results are given from tests on a feed stream to a conventional zinc cleaner circuit. Using wash water to reduce gangue entrainment, the column gave high concentrate grades and high recoveries.

Jan 1, 1987

By Zhu Mingshan, Wu Jiang, Xu Yingqin

A mathematical model to simulate spontaneous combustion of coal in goaf was developed. Under the condition of two-dimensional flaw of air through a bed of uniform mixture of coal, gob, stone etc., the model simulates the temperature rise in the air-and-particle system associated with Arrhenius particle surface reaction. The model is developed as a set of coupled non-linear partial differential equations, which include (1)mass conservation equation for oxygen, (2)energy conservation equation for gas, (3)energy conservation for solid, and (4)velocity equation for gas, that are solved numerically. An elaborate parametric analysis is made of effect of leakage air flux and position of source and sink, parameters relating to the coal accumulating character and the kinetic properties of coal on the tendency to spontaneously combust. In addition, the dynamic process of temperature rise within goaf under several conditions is displayed with picture drawn by computer.

Jan 1, 1991

By Jianmin Qin, Raja V. Ramani

In this paper, the results of a research study on airborne dust transport in a full scale simulated longwall face are presented. The simulated longwall face was set up in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines to conduct experiments under controlled conditions. The controlled parameters in the experiments were the dust dispersion rate, dust size distribution, density of the dust, air velocity, and the rate of travel of the dust generating source. The analyses of the experimental results on mass concentrations, particle size distributions, and real-time respirable dust concentrations are discussed. There are definite spatio-temporal trends between the location of the shearer, the concentration at any location in the face, and the dust generation rates. The size-consist and density characteristics of the source dust, the air velocity in the face, and the air leakage into the gobs all affect the concentration.

Jan 1, 1995

By Manuel Gomez

The purpose of this study was to evaluate the feasibility of using statistical response surface regression analysis to predict the sulfur and ash distributions and the washability characteristics of coal along a seam in advance of mining. Prediction equations were developed with experimental data from channel, bench, and core samples from the Pittsburgh coal seam in Greene County, Pa. It was not possible, with the available experimental data, to construct mathematical models to predict ash and sulfur concentrations between sample points. In the authors' opinion, however, the good agreement between experimentally determined and predicted values at given sample points demonstrates the usefulness of the method. More input data, such as geologic information, seam characteristics (rock-to-coal ratio), petrographic analysis, and chemical data, would perhaps make it possible to predict sulfur and ash concentrations and washability characteristics between sample points.

Jan 1, 1970

By G. W. Healy

The smelting of calcium carbide has always been plagued by eruptions, too often with serious injury y or loss of life. To find their causes, the author calculated an internal energy balance using 1992 data for CaC2 and CaO, and older data for the remaining items. The heat content of the charge, and that of the hot gases formed at the reduction temperature, showed that only a fraction of its heat content can be supplied by these gases. Laboratory data on the electrical resistivity of fine mixtures of coke and non-conductive solids were extrapolated to a commercial carbide charge, and then used to calculate the heat produced by current flowing through the mix from the electrode surface to the hearth, which, under favourable conditions, sufficed to bring the charge to 1900 K and higher, at which temperatures reduction could take place.

Jan 1, 1995

By L. B. Pankratz

The Bureau of Mines determined low-and high-temperature thermodynamic properties for anhydrous ferric sulfate and anhydrous indium sulfate. Low-temperature heat capacities were measured between 50° and 298° K, and enthalpy increments above 298° K were determined. The high-temperature measurements of Fe2(S04)3 extended to 900° K and those of In2(S04)3 to about 1,000° K. A minor transition was found for Fe2(S04)3 at 800° K, with a heat of transition of 540 cal/mole. Tabulations were made of the low-temperature heat capacities and the high-temperature enthalpy and entropy increments. The 298° K entropies derived from the low-temperature measurements were 67.6±0.S ca1/deg mole for ferric sulfate and 72.2±O.5 cal/deg mole for indium sulfate. High-temperature enthalpy increments were also given in equation form.

Jan 1, 1969

By L. B. Pankratz

Enthalpies were determined for synthetic chalcopyrite (CuFeS2) between 298° and 1,050° K and for synthetic bornite (Cu5FeS4) between 298° and 1,100° K by copper-block drop calorimetry. Two transitions were found for each compound. The lower transitions were both crystal transformations from tetragonal (low-temperature form) to cubic (high-temperature form). The chalcopyrite transformation occurred at 830' K with a heat of transformation of 2,405 cal/mole; the bornite transformation was at 485° K with a heat of 1,430 cal/mole. The other transitions were of the second order and were presumed to be magnetic in character. The second-order transitions for chalcopyrite occurred at 930° K, and the one for bornite at 540° K. Enthalpy increments, entropy increments, and heat capacities are tabulated at even temperatures above 298.15° K. Equations of enthalpy are also given.

Jan 1, 1970

By Stephen A. Hare, O&apos

The melting, casting, and welding of the Raney nickel alloy (42 pct Ni-58 pct A1), a methanation catalyst useful in coal gasification, were investigated. Melting was done in graphite crucibles by heating aluminum and adding nickel using a cryolite slag cover. Casting conditions were found to be optimum when the melt temperature ranged from 1,125° to 1,200° C and the mold temperature ranged from ambient to 250° C. Suitable mold materials were found to be quartz, heat-resistant glassware, olivine, and zircon. Welding of the alloy can be accomplished using tungsten inert gas process. Tensile strength of the alloy, in the as-cast condition, was found to be 2,000 1b/sq in with an impact strength of less than 1 ft-1b. The coefficient of thermal expansion was determined to be 18.4 x 10-6/° C after heat treatment.

Jan 1, 1977

By Stephen C. Tadolini

PC-Strand tendons, commonly referred to as cable bolts, have become a major rock reinforcement device for underground mining and civil applications. The most common configuration is a 1+6 strand, which designates a center king-wire, with six outer wires wound around it to form a 0.6-in (15-mm) diameter cable. The capacity of this tendon approaches 30 tons, but the performance is largely dependent on the anchorage medium and the ability of the system to transfer stresses back into the rock mass while reinforcing and suspending the immediate roof. Recent developments to improve the transfer mechanisms of the PCstrand via the anchorage medium by impregnating the individual wires with uniquely designed deformations have resulted in improved anchorage and subsequent cable bolt performance. This paper describes a series of laboratory tests used to develop the initial indentation patterns and numerical modeling simulations that were undertaken to refine and optimize the final designs. The new, indented PC-Strands, offered in both bright and properly galvanized, have been tested in the field and are being used effectively in two new cable bolt products. The results of the laboratory, computer modeling, field testing and in-situ installations provide a glance at the next generation of cable bolts. This suite of testing shows how they will improve the safety and serviceability of openings under adverse ground conditions.

Jan 1, 2012

By W. A. D. Edwards

"The Edmonton region accounted for 40% of Alberta's sand and gravel production in 1981 (about 12 million m3). Most of this production was by commercial operations (75%) for use in essential public works projects (64% in road and asphalt production).Although the Alberta Geological Survey delineated 1157 million m3 of gravel, a number of areas are considered to be in short supply. An econometric model was used for forecast demand in the region. Predictions, based on this forecast and estimated supply, are that 15% of the region's gravel and 3% of the sand will be consumed by the year 2010.The City of Edmonton is the largest consumer of aggregate in the region. Approximately 40% of the gravel in Edmonton's current supply area (about 55 km radius) will be used by 2010. These estimates are considered optimistic because the supply figures do not account for sterilization of deposits - some has already taken place in the region. If 25% to 50% of Edmonton's current supplies (one major deposit) were sterilized it would result in $1,000 million of additional cost due to increased haulage alone.Information on the value of aggregate resources, the location of sand and gravel deposit s and forecast demand has been made available to all municipalities in the region to aid planners and regulators in effective future use of this important resource.INTRODUCTIONAlberta is the second largest producer of sand and gravel in Canada at ab out 50 million tonnes annually. Value of provincial production exceeded $120 million in 1985. In Albert a, aggregate is used primarily in road and building construction (about 50% and 15%, respectively) and is important in such activities as petroleum exploration, oil sands development and the forestry industry.The Edmonton region (Fig. I) accounts for about 40% of provincial production and has a per capita consumption rate of about 13.4 m3 of sand and gravel per annum. Although Edmonton dominates, with approximately 50% of regional production going into the city, aggregate is produced in every county and municipal district in the region.Sand and gravel is essential to the current way of life in the Edmonton region. The resource is valuable and dwindling. The Alberta Geological Survey (a department of the Alberta Research Council) has collected information on aggregate in this region for the last decade which ca n aid government planners and regulators in pre venting sterilization and misallocation of this critical resource. This paper is a summary of that information."

Jan 1, 1989

By T R. Gibbons, I Grayand

Geotechnically massive strata may lead to a host of problems during longwall mining. These include windblast on initial goaf fall, sudden loadings on powered supports, periodic weightings, fractures that may propagate to surface, and extreme subsidence problems. It is essential to identify these problems prior to mining and to appropriately deal with them. The problem is essentially that the rock mass does not breakup evenly and when it does so it tends to produce large blocks which may suddenly move. The rock types that produce these problems tend to be massive sandstones, massive siltstones and sometimes igneous sills. The fundamental problem with these is that they do not breakup readily. This is because the ratio of stress they are subject to compared to their strength is low. Thus, the shallower mines with lower stresses are more subject to this problem than deep highly stressed ones with similar strength rock.

Nov 29, 2022

By J. M. Ross

THE Homestake mine is situated in Whitewood mining district, in the northern Black Hills of South Dakota, in the city of Lead, Lawrence County. The entire property, comprising 557 lode claims with a total area of 3343 acres, is held under United States Patent. The older claims were 300 by 1500 ft. under local regulations, the newer ones 600 by 1500 ft. The Homestake was discovered April 9, 1876, by Moses and Fred Manuel, and Jake Harney, who were drawn into the northern hills, from the Custer placer district, by news of the discovery of rich placer deposits in Deadwood Gulch. They located a number of additional lode claims and, in a short time, the whole country was covered with locations. The Manuel brothers built an arrastre the following winter and took out $5000. The next year the Homestake lode was sold to Senator George Hearst and associates, who organized the Homestake Mining Co. Other companies were formed to exploit other groups of claims and at one time five companies were operating on this deposit, the Father DeSmet, the Deadwood-Terra, the Caledonia, the Highland, and. the Homestake Mining Co. These companies, however, have been merged into the Homestake Mining Company. The first stamp mill, known as the "Eighty Mill," commenced operation on July, 12, 1878, and production has been nearly continuous since that time.

Jan 2, 1925

By Fred D. DeVaney, C. W. Ambler

"Copper sulphate is a common flotation reagent for blende ores. Metallic iron also is present in the mill circuit, and a reaction between the iron and the salt would be in accord with well-known chemistry. The abundance of metallic iron in a flotation feed may be noted by even perfunctory examination. First of all the mine contributes metallic iron, then the coarse-crushing machines add their share, and finally the fine-grinding medium its portion. If the grinding is with cast-iron balls the amount of metallics is greater than when steel is used. Thus it is that much more metallic iron is present than would be indicated by noting the ball consumption. An estimate that the total amount of metallics is twice that supplied by the balls and liners might not be far amiss.That copper sulphate plates out on iron in an acid solution is well known, but since flotation is practiced commonly in solutions where acid has not been added this reaction has not been given sufficient thought.This problem has been the basis of a study undertaken jointly by the Mississippi Valley Station of the United States Bureau of Mines and the Missouri School of Mines and Metallurgy, at Rolla, Missouri. Its importance may be understood better when the tonnage of zinc ores now being treated by flotation in this country is considered. According to Gaudin4 5,536,244 tons of zinc or were treated by flotation during 1927. In these operations copper sulphate was employed as an activating agent; the amount per ton averaged 0.81 pound for straight sulphide zinc ores and 1.16 pounds for complex ores. Since such large quantities of zinc ore are treated by flotation and since metallic iron is always present, the importance of studying their reactions on each other and the effect of their reaction"

Dec 1, 1929

By W. Blake, J. Whyatt

Sixty years of rockbursting in the Coeur d’Alene district has taught painful lessons and led to a number of practical advances in controlling rockburst hazards. This paper summarizes those lessons, concentrating on practical measures that have been successfully adopted to reduce hazards. These lessons are explained in the context of district mining history and current understanding of rockburst phenomena. Overall, the paper provides the practicing mine engineer with an appreciation of rockburst hazards and an overview of practical measures that can be used to control these hazards in the context of Coeur d’Alene district experience.

Jan 1, 2002

Provide longwall operators with an alternative strategy for placement of gob gas ventholes to improve gas production.

Jan 1, 1995