Search Documents

By Katja Reinharter

Arsenic can be found in different sulfidic copper concentrates and residues, which for several years have commonly been used in copper metallurgy, as the “arsenic-free” resources are getting rare. Due to the high toxicity the removal of arsenic in the copper smelting process is a very important topic. The typical chemical slag and sulfur attack on the refractory material is getting enhanced by the presence of arsenic. This work deals with post-mortem investigations of a magnesia-chromite brick and castable used in copper smelting furnaces showing an additional and increased chemical attack by arsenic. The knowledge on the wear behaviour is not only based on a detailed chemical and mineralogical characterization, but also on thermochemical FactSageTM calculations, which are carried out on provided post-mortem samples. Post-mortem investigations on used refractory materials represent an important prerequisite for the product development, as well as for special engineered lining concepts to support our customers.

By Antony Amberg, Gonzalo Saldías, Romke Kuyvenhoven, Catherine Souza, Heriban Soto, Francisco Soto

"Vizcachitas is an advanced stage copper–molybdenum porphyry deposit, fully owned by Los Andes Copper and located in Central Chile. The property contains an indicated resource of 1,038 million tonnes grading 0.37% Cu and 0.012% Mo, and an inferred resource of 318 million tonnes grading 0.345% Cu and 0.013% Mo (Coffey & Alquimia, 2014). The deposit occurs in the same geological belt as several other giant copper-molybdenum porphyry deposits including Río Blanco-Los Bronces, Los Pelambres-Pachon and El Teniente. In 2018, the original Preliminary Economic Assessment (PEA) study from 2014 was updated; this paper presents the geometallurgical testwork that was performed to support that update. The testwork focused on the metallurgical characterization of 40 DDH samples and the development of a more profound orebody knowledge by relating geological features with metallurgical performance. The scope of work included complete chemical and mineralogical QemSCAN characterization; SAG, ball mill and abrasion testing; complete rougher and cleaner kinetics including locked-cycle-test; environmental ABA and settling tests on rougher tailings. The results show that the ore can be classified as medium-hard, with a hardness that is slightly below the average for large Cu/Mo deposits in the region. A good correlation was found between lithology and breakage characteristics, implying that the specific energy consumption (kWh/t) is well correlated to rock type. The results of the flotation tests were very encouraging and did not show significant variability. An overall Cu recovery of 91% can be expected for the flotation circuit. The use of a relatively coarse primary grind size gave good final recovery and grade for both Cu and Mo, and deserves further attention in future work, as this impacts positively both energy consumption and water recovery.INTRODUCTION Los Andes Copper Ltd. is a Canadian exploration and development company focused on the acquisition, exploration and development of advanced stage copper deposits in Latin America. The company owns 100% of the Vizcachitas project in Chile, the largest copper deposit in the Americas not controlled by the majors. Vizcachitas is a copper-molybdenum porphyry deposit, located 120 km north of Santiago, in an area of very good infrastructure."

Jan 1, 2018

By Suman Giri

Non-Intrusive Load Monitoring (NILM) is a method of extracting appliance-level power consumption information from aggregate circuit-level data with the goal of giving users feedback regarding their energy consumption so they can take control of their consumption habits. In this paper, we present a novel algorithm for classification of on and off states of appliances. We compare the performance of our algorithm in on state detection with a pervious paper that evaluated the same dataset and show that it performs up to 13% better. We also present the results of a case study where we collected data for different modes of a cooktop, microwave and dishwasher and used our algorithms to perform power estimation. The error on ten different setups in the test bed ranges from 1% to 32%. We discuss our results and lay out ideas for future work.

Aug 1, 2013

By P N. Martens

In the course of the development of the Report of the World Commission on Environment and Development (WCED) in the 1980s an expression was introduced in the public discussion on environment and development that influenced the international and national policies of the last 20 years in all areas: sustainable development. The UN decided in 1992 to implement a program with the Agenda 21 which contains the demand for developing indicators for sustainable development. In this context an indicator is understood as a quantitative or qualitative measure that can be measured or described throughout time and which moreover is able to depict the current status and changes. In order to enable for a simple holistic assessment of sustainable development, highly aggregated indicators are required, which integrate the criteria identified as relevant within a framework to be defined. In the presented paper, sustainability indicators for the mining industry are developed that account for the allowances of the sustainable development concept and the Agenda 21. The indicators are quantifiable and traceable through time so that developments can be traced and assessed. Furthermore, the indicators account for the multidimensional aspect of sustainable development. They are designed to allow for the integration of several dimensions in one indicator. The premises that are underlying the development of the indicators are the minimisation of negative impacts on the environment and society while simultaneously considering the maximisation of social and economic factors. Moreover, the participative momentum that is part of the sustainability idea is safeguarded in explicitly integrating the social acceptance of certain measures into the assessment. The indicators presented are based on the logical combination of statements through the use of Boolean algebra. Starting with basic statements for which the logical value is oriented on the sustainability paradigm, complex multidimensional statements can be constructed and assessed.  

Jan 1, 2009

By Matthew Wilcock, Kenichi Soga, Peter Wright

"This paper discusses how an existing grey cast iron segmental tunnel lining responds to construction of a new SCL tunnel transversely beneath with zero clearance; how the damage assessment for the existing tunnel was conducted for impact of longitudinal movement; how the tunnel is subsequently instrumented to observe both movement and stress manifestation at its longitudinal connections and how the results from the instruments compare with the prediction. An assessment of neutral axis of the tunnel in longitudinal flexure is also explored using interpolated horizontal displacement data from a conventional monitoring system. INTRODUCTION The Royal Mail Tunnel (RMT) (formely Post Office Tunnel or ‘Mailrail’) was constructed using semi-mechanised deep level construction techniques from 1914 and 1917 (Lee 1938). Commencing full commercial operation in 1926, the system was until 2003; conveying parcels the 6.5 miles between seven sorting offices in the center of London, and linking the system with main line rail stations, Paddington and Liverpool Street (The British Postal Museum & Archive 2013). A single tunnel of 2.74m internal diameter facilitated a bi-directional twin narrow-gauge (~611mm gauge) railway road system for electric driverless operation. The tunnel lining is segmental grey cast iron (grade 10) made up of six flanged segments and a smaller flanged key segment; constructed into a ring of width 508mm The external diameter of the tunnel is 2.971m. For further details of the tunnel lining and material properties are outlined by (Devriendt & Alhaddad 2014).London Underground Bond Street Station is a major station of the London Underground system in the very center of London; in its vicinity, the RMT runs west-east perpendicularly above the north south Jubilee Line tunnels. Historic survey record of the Jubilee Line’s (the then Fleet Line) construction in 1974 and its impact on the RMT case is documented in (Crossrail 1993): it is one of only a hand full of case-studies frequently cited when assessing the impact of new construction scenarios of this type; not least including the assessment of the same tunnel, at the same site some 40 years later, and the subject material for this paper: It noted significant vertical displacement of ~90mm to the RMT without noticeable serviceability or operational impediment."

Jan 1, 2016

By I. A. Khabarova

The paper presents the results of experimental investigations of the effect by high-power nano-second electromagnetic pulses (HPEMP) on change of surface composition, physical-chemical and flotation properties of pyrrhotite, and search of optimal combination of flotation reactants providing increase of metal extraction from disseminated copper-nickel ores. Preliminary electropulse effect on products before flotation allows to create optimal conditions for flotation separation of pentlandite and pyrrhotite owing to forming the new phases and defects on the surface of sulphides. It was established, that the yield of monomineral fractions of pyrite, pyrrhotite and chalkopyrite increases by 5%~15 %, compared with flotation with one butyl xanthenes (BX), during usage of combination of thionic carbamate (isopropylmethylthionocarbamate (ITC) or isopropylethyl- thionocarbamate (Z-200) with butyl xanthate (BX). Sorption of investigated reactants and strength of their fixing on the surface of minerals are examined; it helped to reveal the cause of rise of floatability of sulphide minerals for the case of combination of reactants. Preliminary high-pulse processing and reactant conditions with usage of combination of thionic carbamate and xanthate have been tested on the sample of disseminated copper-nickel ore from Norilsk region.

Jan 1, 2014

By Michael Arriagada, Ivan Arriagada

"As mines return to shafts to economically exploit deeper reserves, two methods mine owners use to minimize short term costs are: sinking shafts in phases and refurbishing old, existing shafts. While there may appear to be benefits to utilizing existing infrastructure, often this is not the case, resulting in missed deadlines and added costs. Similarly, if proper long term planning is not executed when sinking a shaft in phases, additional costs and downtime will be accrued. This paper will take an in depth look at both of these options with an eye towards optimizing costs, minimizing downtime, and facilitating construction. INTRODUCTION With the onset of mechanized mining and large capacity trucks, many mines turned away from shafts and began to use ramps to haul ore to surface. However, continual exploitation of mineral reserves located closer to surface, combined with the subsequent unearthing of additional resources at greater depths, forced mines to go deeper and deeper to extend the life and keep the operation running. In shallow mines, hauling ore by truck was an economical option. However, as mines get deeper, driving ramps takes additional time, and hauling over longer and longer distances becomes less economic, both in terms of cost and time. For this reason Mexico, in particular, has seen a jump in the number of shafts which have been put into production, as well as having a number of shafts in different stages of development and still more in the conceptual stages. Many of the shaft projects in Mexico are being designed in phases, with the hoist and equipment purchased capable of reaching the ultimate planned depth of the shaft, but with sinking operations stopping short at an intermediate depth. A loading pocket is then installed to start exploiting mineral at this depth sooner, with subsequent phases planned for a later date using either a rock pentice or bulkhead to separate the sinking operations from the active shaft above. Currently, we are directly involved in two such projects which are actively being deepened, as well as having seen various others already reach completion. If done properly with the long-term plan in mind, sinking in phases can be a very viable option, allowing for faster production while fully utilizing the equipment at various depths. However, there are many issues which can arise when sinking a shaft in phases that if not properly examined and planned for from the outset, have the potential to eliminate the gains hoped for when it was decided to sink in this manner."

Jan 1, 2019

By Haydn H. Murray

This paper presents the results of test work performed with a Pacific Electric Motors (PEM) high intensity magnetic separator (20 kilogauss) , a unit capable of separating weakly, as well as strongly, magnetic minerals in the particle size range of sands to clays. Tests were performed on some 40 industrial minerals. With some minerals excellent separations were attained and with others intermediate and poor separations were accomplished. This study is a preliminary survey and many of the intermediate and poor results can be improved as separation problems are worked out with additional test work. It is demonstrated that with a number of industrial minerals high intensity magnetic separation is a viable beneficiation technique that is economic ally feasible.

Jan 1, 1976

By B. Akwasi Osei

The lack of metrics to assess clamshell formation dredgeability limits the ability of engineers to predict the dredgeability of compact material and increases the risks associated with clamshell selection. Research is needed to develop metrics for predicting clamshell dredgeability. The objective of this paper is to evaluate possible metrics to predict the dredgeability of compact aggregates by hydraulically actuated clamshell dredges. Data on cylinder pressures and displacements, motor current, bucket tilt and cycle time (CT) were collected from a dredge. Work done and motor energy, potential metrics, were computed and their suitability in predicting dredgeability evaluated. Data analysis shows that; there is no correlation between tilt angle and work done or motor energy; a low correlation between CT and work done, and a strong correlation between CT and motor energy. Work done is a better measure of formation dredgeability, than motor energy, as it shows lower variability. However, in difficult digging conditions, work done alone does not accurately predict dredgeability. This work shows that, it is feasible to use cylinder pressures and motor signals data to predict dredgeability.

Jan 1, 2010

By Hrayr Agnerian

The fair market value of an exploration property is determined by its potential to host a mineral deposit. This potential is gauged by the results of previous exploration, exploration stage, meaningful past expenditures and remaining targets that are not yet tested. Values of exploration properties can be viewed as distinct points in a three-dimensional space defined by orthogonal axes, namely: Exploration Stage (x-axis); Cumulative Expenditures (y-axis); and Property Value (z-axis). In general, these values are estimated by applying activity factors on previous exploration expenditures, e.g. an activity factor of 100% for an active property with good potential and a factor of 50% for an active property but past expenditures have not upgraded the property. At certain periods, a market factor may also be applied to reflect the activity of mineral property acquisitions. For properties that do not exhibit any exploration potential, only nominal values are applied.

Jan 1, 1996

By Batric Pesic

Dissolution of gold with sodium bromate solutions of various compositions was studied by using a rotating disc technique. The role of bromide ion, acid and externally added bromine was examined. It was found that sodium bromate could not dissolve gold in the absence of either acid or bromide ion, or both. When acid was absent, no bromine necessary for gold dissolution could be produced. When bromide ion was absent, formation of soluble gold bromide species, AuBr,-, was not possible. Bromate concentration had a complex effect, and it was dependant on bromide ion concentration. For fixed initial bromide ion concentration, gold dissolution rate increased with sodium bramate concentration increase until certain level, beyond which further increase of bromate concentration decreased the gold dissolution rate. The negative effect of bromate was explained by the depletion of necessary bromide ion. Sulfuric acid concentration effect was a function of initially present bromine.

Jan 1, 1992

By E Marambio, R Brändle, G Fischer, G von Rickenbach, L Burgos, R Luis Fonseca

Ground support systems must provide safe and effective designs for underground excavations under high stress conditions. These systems must be capable to resist dynamic impacts and yielding during the loading process. In this context dynamic testing of the reinforcement and retaining elements that compose the ground support system are required to study and improve the behaviour of these elements under dynamic load events. During the last years, Geobrugg has been working on the improvement of retaining products by testing them in a large-scale impact test facility located at Walenstadt, Switzerland. The test facility is composed of a double level platform with a square-shaped pyramidal trunk geometry, in the upper level housing a loading mass that drop from a height up to 5m. The loading mass is guided by one central steel pipe, and the impact occurs in the sample to be tested located at the lower level in a slab with an area of 3.6m × 3.6m where the ground support system is installed. During the last years, this innovative facility has been used to test several configurations of ground support systems. The results of these tests have enabled to improve the understating of the behaviour of ground support systems under dynamic loads. In this manuscript, the arrangement, measurement, results, and the preliminary analysis of a single impact dynamic test performed during 2021 of a ground support system with a high-tensile steel wire mesh MINAX 80-4.6 is presented.

Apr 26, 2022

By Herbert Hoover

YOUR committee asks that I speak today on the relations of the engineering profession to public affairs. That takes in a lot of ground. This being a cheerful occasion, I will assume that I should exclude the engineer's function as a taxpayer. This being a nonpartisan occasion, I will assume that I should not refer to his voting emotions in 1940. Perhaps what was in the minds of your committee was the application of engineering thought to the confusions of the times. That is also a lot of ground. I fear, however, its boundaries disappear in mirages and rainbows on all sides. Now any entry of the engineer into public affairs involves his breaking into the fields of the sociologists, the economists, and the politicians. However I don't know why, seeing the difficulties these professions are having, they should not welcome a little help.

Jan 1, 1939

By Leandro de Arruda Santos

O objetivo deste trabalho foi avaliar o comportamento mecânico sob flexão de um instrumento endodôntico constituído de Ni-Ti M-Wire e comparar suas respostas com aquelas obtidas de um instrumento de Ni-Ti superelástico convencional com a mesma geometria, utilizando-se simulação por elementos finitos. Um instrumento ProTaper Universal F1 foi selecionado para este estudo. O modelo geométrico para a simulação numérica foi gerado através de micro-tomografia computadorizada e os dados para os modelos constitutivos foram obtidos por meio de ensaios de tração realizados em laboratório. A simulação numérica foi realizada em ABAQUS, com condições de contorno baseadas na especificação ISO 3630-1. Os resultados mostram que instrumentos de Ni-Ti M-Wire apresentam maior flexibilidade e menores valores de tensão quando submetidos à flexão, o que indica que estes instrumentos são mais resistentes à fadiga por flexão.

Aug 8, 2018

By Marcos Meyer

A pelotização é um processo de aglomeração com objetivo de agregar valor aos finos de minérios de ferro (pellet feed). A partir de 2010, a mina de Brucutu situada no Quadrilátero Ferriferro (QF) passa a ser a maior fornecedora de matéria prima para as plantas de Tubarão / Vitória-ES. O estudo avaliou a performance industrial de duas misturas com alta participação de minério de Brucutu, acima do padrão utilizado na usina de pelotização. Os minérios compostos nas misturas foram caracterizados por análise química, física, mineralógica e microestrutural. O desempenho operacional mostrou superior à mistura padrão utilizada para a produção de pelotas para redução direta, permanecendo com os parâmetros de qualidade consoantes com as especificações do produto final. O conhecimento das características geometalúrgicas destas misturas com minério de Brucutu em maior escala foi de suma importância para adequar o processo e custo das principais operações unitárias da planta envolvida (moagem e forno).

Aug 1, 2018

By Foluke Salgado de Assis

Este trabalho visa apresentar alguns resultados obtidos através de ensaios balísticos realizados em sistemas de blindagem multicamada. Seguindo as especificações da norma americana NIJ 0101.06, foram realizados ensaios utilizando munição de calibre 7,62x 51 mm, que possui velocidade acima de 800 m/s. A blindagem multicamada utilizada possui como camada frontal uma pastilha hexagonal cerâmica (alumina dopada com 4% de nióbia), segunda camada de compósito de matriz poliéster reforçada com tecido de juta e como terceira camada uma placa de alumino 5052 H34. A utilização de compósitos poliméricos reforçados com fibras naturais em substituição às fibras de aramida é de grande interesse, pois além de desempenharem a mesma função no sistema de blindagem, possuem um valor de mercado bem menor. Com os resultados obtidos do ensaio balístico, os valores foram associados com o seu comportamento dinâmico utilizando o método do casamento de impedâncias.

Aug 17, 2017

By Boo Hyun Nam, Berk Turkel, Luis G. Arboleda-Monsalve, Jorge E. Orozco-Herrera

Construction of buildings, roads, and traffic activities generate vibrations to urban infrastructure. The vibrations produced by construction activities have an impact on the soil through which they are transmitted. These effects become much more significant in granular soils. The soil conditions in Florida consist mainly of sandy soil deposits and this makes driven piles a commonly used method. In the design of deep foundation installations, it is significant to consider the potential construction issues related to the driving process. This process generates vibrations in the surrounding soils and thus, its effects on nearby soils and structures must be considered. This paper presents a web-based survey conducted among geotechnical engineers in Florida to better understand the common practice and experience regarding the effects of pile driving on surrounding soils and structures. The perception of different practitioners in the state of Florida on ground deformations and damages to adjacent structures induced by deep foundation installations are investigated. The engineers who have experienced ground vibrations and deformations were asked to define the susceptible soil conditions and main triggering factors of large ground deformations induced by pile driving. Sandy soils with loose to medium relative densities were found to be the most susceptible soil condition to generate ground deformations. Conclusions are drawn regarding the importance of considering ground vibration monitoring during the design phase of deep foundations.

Oct 1, 2022

By Leandro Rocha Lemos, Guilherme Liziero Ruggio da Silva, Iara Patricia Vieira de Oliveira, Paulo Santos Assis, Lorena Cristina Amorim Moura

O coque fica exposto a diferentes solicitações mecânicas do tipo impacto, abrasão e compressão, desde o desenfornamento até o seu consumo no Alto-Forno. Para evitar que o coque sofra uma acentuada degradação, é exigido que o mesmo apresente uma elevada resistência mecânica a frio. Para monitorar tal parâmetro, utiliza-se principalmente o teste de tambor, porém este contempla apenas a degradação por impacto e abrasão. Neste contexto, este trabalho desenvolveu uma metodologia para avaliar a resistência mecânica à compressão, inicialmente em partículas individuais de coque, apontando quais seriam as granulometrias mais resistentes. Os coques foram transformados em corpos de provas e testados em máquina de ensaio universal. Os resultados apontam que a tensão média de ruptura cresce com o aumento da granulometria. Posteriormente, foi avaliado a resistência mecânica à compressão em leito de coque, onde foi possível simular em uma prensa hidráulica, a pressão que a coluna das cargas exerce sobre o leito de coque no Alto-Forno e, posteriormente, correlacionou a compressão com o teste de tambor e se obteve excelentes resultados.

Oct 1, 2019

By Carlos Henrique Silveira Aguiar

O tubo formador de espiras é uma guia que está localizada no Laying Head, especificado de acordo com a norma ASTM 335P22, e tem por função conformar o fio-máquina na forma de espiras sobre o transportador Stelmor. O Laying Head gira continuamente, durante a operação normal, sendo que a cada revolução do tubo, uma espira é produzida, cujo diâmetro é determinado pelo raio final do tubo e pela velocidade do Laying Head, em relação à velocidade do Laminador. Estes tubos, durante a laminação dos aços BEXX, sofrem um desgaste acentuado, que é provocado pela carepa formada durante a passagem do fio máquina pelas caixas d’água, durante o processo de resfriamento. Desta forma, torna-se necessário trocá-los a cada 200t laminadas do referido aço, com tempo estimado de 30 minutos de parada. Além disso, há um desgaste físico acentuado na atividade de troca dos tubos, que coloca em risco a segurança dos funcionários. Outro efeito indesejável relaciona-se com o risco de ocorrência de sucata de linha, provocada pelo rasgamento do tubo, quando são fornecidos tubos cuja composição química se apresenta no limite inferior de especificação. Há programa de laminação que exige até 6 trocas diárias de tubo. Com a proposta de se incrementar a tonelagem laminada por canal dos discos de laminação do Bloco No Twist, tornou-se necessário desenvolver um tubo com insertos de metal duro, com vistas a aumentar a vida útil dos mesmos, como também a produtividade do Laminador 2.

Jul 30, 2018

By D. Hu, J. Xu, N. Liao, C. Wu, J. Ye

The vertical stirring mill’s fine grinding equipment is affected by the operating conditions during the grinding process. The grinding media has a great influence on the energy consumption and particle size distribution. This paper investigates the fine grinding performance of nano-ceramic balls and steel balls of the same weight for magnetite by a wet grinding process in a vertical stirring mill, where 15 mm nano-ceramic balls and 12 mm steel balls are used as grinding media to carry out batch grinding tests. We have observed that the newly qualified particle content of the nano-ceramic balls is higher than steel balls of the same weight at the same specific energy. The reason may be the advantage of a greater surface area and volume filling rate with the nano-ceramic balls. Moreover, the specific energy of nanoceramic balls is less than steel balls of the same weight under the same grinding fineness. In addition, energy efficiency indicates that the nano-ceramic ball has a higher energy efficiency than a steel ball of the same weight. This is due to the light bulk density of nano-ceramic balls. The application of a nanoceramic ball in a vertical stirring mill will improve iron ore grinding performance. Keywords: Steel balls, nano-ceramic balls, vertical stirring mills, fine grinding, particle size distribution, energy consumption

Jan 1, 2020