Search Documents

By F. H. Nehl

The U.S. Bureau of Mines investigated the selective electrowinning of Ag and Au from cyanide solutions contaminated with Cu with the goal of decreasing the amount of Cu co-deposited. Decreasing Cu co-deposited will reduce refinery costs. Direct current was applied to the cell in pulsed and square wave voltages at 0.7 A?h per 150 mL of solution. Times tested for each cycle ranged from 1 to 10,000 ms. Graphite, lead, and stainless steel were evaluated as electrode materials. Square wave e1ectrowinning at 70? C gave the best separation of Ag and Au from Cu. Applying 2.5 V during the duty cycle, 0.0 V the rest of the period, a duty cycle of 10 to 30 pct, and a period of 100 ms to 1,000 ms gave the following results: Ag concentrations decreased from 34 µ g/mL to 0.1 µ g/mL, Au concentrations decreased from 54 µ g/mL to 0.2 µ g/mL, and Cu concentrations remained almost constant at 560 µ g/mL.

Jan 1, 1993

By Tiago Bristt Gonoring

Neste trabalho foi avaliado o efeito da adição de metano e argônio sobre a redução a plasma de pós de hematita de alta pureza (com %Fe2O3> 99,00 e tamanho de partículas

Aug 8, 2018

By Alessandro Francelino Nogueira

A utilização de lasers de pulsos ultracurtos é uma alternativa para a realização de microusinagem em superfícies de metais, com aplicações diversas em inúmeros segmentos industriais, além das áreas aeronáutica, aeroespacial e naval, onde há crescente preocupação com a eletrônica embarcada. Neste trabalho foram realizadas microusinagens em superfícies de titânio utilizando laser de pulsos ultracurtos de femtossegundos. Tal processo resultou em mínima transferência de calor para o material, evitando assim e deformação superficial da chapa de titânio e a formação de material ressolidificado na região ablacionada, que são inconvenientes presentes na utilização do laser chaveado de pulsos longos da ordem de nanossegundos. Foram executados três tipos de microusinagens, com variações nas distâncias entre as linhas usinadas. Foi verificado ainda que a molhabilidade aumenta quando há o aumento da distância entre linhas usinadas. Finalmente, para a alteração da superfície com uma ínfima remoção de material, constatou-se que a utilização de lasers de pulsos ultracurtos proporcionam grandes benefícios para a integridade do material ablacionado.

Oct 30, 2017

By Jéssica Sobrinho Lopes

No presente artigo objetivou-se, principalmente, promover a síntese e caracterização de biofilmes ecológicos elaborados a partir do amido de batata doce e da crueira de mandioca, utilizando como plastificantes o glicerol e o sorbitol. O amido da batata doce foi obtido através de descascamento, trituração, filtração, decantação e secagem, respectivamente; enquanto a crueira de mandioca foi obtida por doação. Os biofilmes foram confeccionados na proporção de 3 gramas de amido/100 gramas de solução filmogênica, e 30 ou 40 % de plastificante em relação à massa de amido, as soluções foram aquecidas e agitadas à 80ºC, depositadas em placas Petri, e secas em estufa à 50ºC por 24 horas, e à temperatura ambiente. As amostras de biofilmes foram analisadas quanto aos aspectos visuais, solubilidade em água, teor de umidade, resistência química e Espectroscopia de Infravermelho por Transformada de Fourier (FTIR). Obteve-se 18,16% de rendimento na extração do amido; solubilidade em água e teor de umidade variando, respectivamente, entre 0,03-0,12, e 2,79-11,812%; os filmes mostraram-se insolúveis em clorofórmio, acetona e álcool; e as reações foram confirmadas através de Espectroscopia de Infravermelho por Transformada de Fourier.

Oct 30, 2017

By Murillo Romero da Silva

Ligas com memória de forma (LMFs) são ligas metálicas capazes de recuperar o seu formato e tamanho original após deformação plástica quando aquecidas acima de uma temperatura crítica. Diversos casos de possíveis aplicações paras as LMF têm sido justificados no campo científico, com alguns poucos casos identificados para aplicação em massa, existindo uma ausência na literatura de uma análise crítica da aplicabilidade das mesmas que leve em consideração aspectos industriais e de mercado. Dessa forma, se faz necessário um estudo mais aprofundado que correlacione as ideias científicas geradas com a produção industrial e com a comercialização de LMFs. Nesse contexto, o trabalho visa através de levantamento e análise de patentes e artigos científicos, assim como por contatos industriais, estabelecer uma relação entre o desenvolvimento científico e o comercial das LMFs. Mais de 11 mil artigos e mais de 7 mil patentes foram produzidos nos últimos 16 anos, sendo observado uma tendência crescente da criação de conhecimento de LMF, o qual já vem sendo aplicado na indústria, justificando assim os esforços observados no campo científico. A área biomédica se destaca como a mais bem estabelecida no campo das LMF, com destaque para a utilização das ligas a base de NiTi.

Aug 17, 2017

By Janeir Ribeiro Dutra

Os aços siliciosos de grão orientado (GO) e de grão não orientado (GNO) são aços ligados ao silício para aplicações elétricas. O aço silício de grão orientado possui as propriedades magnéticas otimizadas na direção de laminação, enquanto o de grão não orientado apresenta boas propriedades em qualquer direção. O aço elétrico de grão orientado tem como principais características as excelentes propriedades magnéticas, desenvolvidas especialmente para a redução das perdas magnéticas e aumento da eficiência de máquinas elétricas. Durante o processo de elaboração do aço o principal desafio é o controle de elementos como alumínio, titânio e enxofre, elementos estes provenientes da carga metálica (sucata e gusa) e adições de ligas na panela. Para este controle ser eficaz a estabilidade da composição química da escória na metalurgia secundária é de fundamental importância. O fluxo produtivo do aço GOAT na metalurgia secundária inicia-se no processo VOD(Vaccum Oxygen Decarburization) com término no forno panela. Este trabalho promoveu a adequação da escória da metalurgia secundária do aço GO através da: i. revisão do padrão de consumo de fundentes, mediante estudo de balanço de massa; ii. desenvolvimento de escória sintética para ajustar finamente a basicidade da escória. Os estudos de balanço de massa apontaram que em determinadas situações havia a necessidade da correção da escória para aquecimento no forno panela; iii. implementação de amostragem de escória ao final do processo VOD para correção da basicidade de escória para aquecimento no forno panela; iv. criação de modelo para correção da basicidade da escória. Após a implementação do projeto o controle da escória no forno panela ficou mais efetivo promovendo: i. redução dos teores finais de alumínio e titânio ao final do processo de elaboração no forno panela; ii.possibilidade de correção da quantidade de escória para aquecimento no forno panela sem comprometer a basicidade de escória requerida no processo; iii. atendimento a faixa otimizada do aço GOAT (M3, maior qualidade) passou de 33% para 65%; iv. redução do desgaste de panelas na elaboração do aço GOAT na metalurgia secundária; v. redução do risco de sucatamento por fora de faixa em alumínio e titânio do aço GOAT na aciaria que representou nos últimos 4 anos uma perda ao processo superior a R$ 1,2 milhão; vi. estabilização da basicidade binária da escória final do Forno Panela dentro da faixa desejável.

Oct 30, 2017

By Yuqi Zhao, Zhiyong Lin, Leiting Shen, Hongyang Wang

Gibbsite-type bauxite is the main material for alumina extraction by Bayer process globally, while the iron in red mud is difficult to use for the high alumina content. Therefore, the efficient separation of iron and alumina is the premise for the resource utilization of red mud. In this work, the separation of iron and alumina in red mud containing 47.45% Fe and 11.58% Al2O3 was studied through reduction roasting followed by magnetic separation. The analysis methods of XRD, VSM, SEM, and EDS were used to investigate the phase transformation of red mud during reduction roasting. Results show that hematite can be firstly reduced into magnetite, and alumogoethite into magnetite and alumina. Then, the magnetite reduction undergoes the process of Fe3O4→FeO→Fe, while alumina can react with FeO to form hercynite. The hercynite is ultimately reduced into metallic iron and alumina at elevated temperature. The specific saturation magnetization of reduced product is closely related to its main minerals, that is, the specific saturation magnetization of magnetite and metallic iron is higher than that of wustite and hercynite. The mass ratio of Fe to Al2O3 in magnetic concentrate increases with roasting temperature, from 4.55 at 600 °C to 10.27 at 1200 °C. Therefore, efficient separation of iron and alumina in red mud could be achieved through deep reduction-magnetic separation.

May 2, 2024

By Jae-Chun Lee, Sadia Ilyas

We investigate the technical feasibility of bioleaching of metals from low grade sulphidic ore. Experiments were conducted with an adapted consortium of Sulfobacillus thermosulfidooxidans and Thermoplasm acidophilum in batch bioreactors (1.5 L), small columns (10 kg ore load, 8 % S0 sludge) and large columns (80 kg ore load, 12 % S0 sludge). Approximately 83 % Ni, 85 % Cu, 55 % Fe and 81 % Zn was leached out in batch mode while 93 % Ni, 89 % Zn, 81 % Cu and 65 % Fe was leached out in column reactors. Bioleaching potential improved by acid pre-leaching, adaptation of microbial consortium and periodic bleeding of effluents.

Jan 1, 2014

By M. Tanaka, T. Oishi, K. Koyama, S. Alam

"A novel hydrometallurgical process for copper recovery from waste printed circuit boards has been proposed, which consists of selective leaching of copper metal as Cu(I) by Cu(II) in ammoniacal alkaline solution, purification, and electrowinning. The distinct feature of this process is much lower power consumption during the electrowinning than that during the conventional one from acidic copper sulfate media, because the deposition of copper metal from Cu(I) at the cathode and the oxidation of Cu(I) to Cu(II) at the anode take place in the present method. In the laboratory-scale tests using waste printed circuit boards, high purity copper which contains 1.1ppm of impurities was obtained in a chloride system. INTRODUCTIONThe recovery of various metals from waste materials is an important issue in order to conserve the environment and metal resources. Copper is used for cables, electric appliances, etc., and is currently a very important material for industries and will continue to be in the future. Among the wastes that contain copper, one of the most complex recycling materials is electronic scrap like printed circuit boards (PCB), which generally contain 10-30% copper as well as plastics, fibreglass and other metals. There are two ways to recover copper, either pyrometallurgical or hydrometallurgical. Hydrometallurgical treatments generally have more flexibilities in the process scale and control. The separation processes tend to become complicated because of the poor selectivity during the leaching in the sulphuric and hydrochloric acid media. On the other hand, the use of ammonia as a complexing agent, gave a higher selectivity for copper leaching (Nigo, Majima, Hirato, Awakura, & Iwai, 1993; Majima, Nigo, Hirato, Awakura, & Iwai, 1993; Zhou, Shinme, & Anezaki, 1995; Koyama, Tanaka, & Lee, 2006) .In this study, recycling process containing leaching, copper deposition at a cathode and oxidation of copper(I) at an anode from ammoniacal alkaline solutions containing Cu(I) or Cu(II) is introduced. Furthermore, copper recovery from a waste printed circuit boards and impurity behaviour was examined in ammonia-ammonium sulfate (sulfate system) and ammonia-ammonium chloride (chloride system) systems."

Jan 1, 2012

By R. Mishra

The validity of the concept of mine resistance in ventilation systems is examined. Mine resistance is the proportionality constant relating the head generated by a fan and the quantity flowing through it when the fan is connected to a mine circuit. It is the total effect of all branches in the mine ventilation circuit. Its importance lies in the fact that for new mine projections, and in the extensions of existing mines, ventilation calculations are usually based upon adjustments of the mine resistance. In ventilation circuits with regulation, and/or with multi-fans, simple adjustments of the mine resistance curve do not lead to correct solutions. A ventilation system consists of several interconnected subsystems where one subsystem behavior affects that of the others, and the total system. Through a series of simple but realistic examples, the authors will demonstrate the importance of the systems concept in mine ventilation, and its practical application to coal mine ventilation planning.

Jan 1, 1977

By H. Michael Breza

Texasgulf Inc. installed bucketwheel excavators and overland conveyor sysems at its Aurora, NC phosphate mine o increase the productivity and flexibilty of the surface mining operation. This ;ystem has significantly improved overrall. Its flexibility is evidenced by adapation to operation requirements, such is mining area moves, movement of xcavated overburden to designated ites, selective handling of overburden, poll placement contouring, and proiding an environmentally sound and afe operation. The system's productiv:y is evidenced by case studies relating. overall production, excavation rates nd cost-effectiveness. There are many competing alternaves available for excavating uncon)lidated overburden: truck-shovel, raglines, dredges and bucket wheel ticavators. These alternatives also may used in tandem to recover reserves icated at greater depths.

Jan 1, 1993

By D Kentwell

A resource model serves two main purposes depending on the stage of a project. The first is to provide an early indication of likely tonnages and grades at certain cut-offs so that decisions can be made on whether continued spending on the project is justified. The second is to provide a basis for mine planning, feasibility studies and reserves. Resource models are not designed for selection of actual blocks in the ground for processing. This is the purpose of a grade control model, which is created at a stage beyond both resources and reserves.Inferred, Indicated and Measured Resources contain different levels of uncertainty with respect to the accuracy of the resulting grade and tonnage curves. These uncertainties arise from three broad areas: quality of information, geological assumptions and estimation technique. This paper focuses on known problems with the ordinary kriging (OK) estimation technique. Resource estimates often produce smoothed block grade distributions with much lower block grade variability than true selective mining unit (SMU) block grade distributions. There are two main factors that are involved in this smoothing. Firstly, where the block size used for estimation is larger than the SMU block size, this will smooth the block grade distribution and move the grade and tonnage curves away from the true SMU block grade and tonnage curves. Secondly, and less well recognised, is that smoothing is inherent in the OK estimator. This also moves the grade and tonnage curves away from the true SMU grade and tonnage curves, even when the estimate is done at the SMU block size. There are a number of techniques, such as simulation, uniform conditioning and degraded search neighbourhoods that can provide a better approximation of the true SMU block grade and tonnage curves at the expense of individual block accuracy.This paper aims to explore the extent to which OK resource estimates designed to maximise individual block accuracy can differ from (an estimate of) the true resource at SMU block size in terms of grade and tonnage curves. The differences at economic cut-offs and above are examined. In some cases these differences are significant. Both the OK estimation technique and block size play a part in the differences observed. To do this we will examine a number of commodities and deposit types using real project data.The conclusion is that the current industry standard default practice of targeting maximum individual block accuracy (conditional unbiasedness) using OK at resource stage, without consideration or evaluation of the extent of associated smoothing at SMU scale, can lead to significant errors in fundamental mine planning decisions. This then has implications for resource classification if the classifications are based heavily on the OK quality without consideration of the true SMU distribution.CITATION:Kentwell, D, 2014. Aligning resource estimates with mine planning, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 185–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Alan Diaz Butron, Eng. Thierry Bernard

"In tunnel blasting the most challenging objective is definitively obtaining the maximum advanceassociated to a minimum overbreak. Achieving 100% of advance with no overbreak is the targetchallenge by Chavimochic Consortium. Chavimochic Special Project is an irrigation system that extends throughout much of the coast of the La Libertad Region, on the north coast of Peru. In 2012, it began management for construction of the third and last stage of CHAVIMOCHIC to irrigate lands of Chicama Valley, North of Trujillo. This project of 13 Km (8 mi) of various tunnels, it's a combination of technology and daily optimization by experienced people, which allow to accomplish the objective. Achieving this advance with no overbreak provide a huge saving on time. This paper describes the method, technology used, and the results obtained on more than 600 blasts done with conventional initiation system on the first 3 km (1.86 mi)."

Jan 1, 2017

By Judson G. Brown

In order to filter small amounts of fine slimy solids the reversible cake-filtration process was developed. The filterable solids contents lion in feeds can range from less than 1 ppm up to about 5%. The relative advantages of this process, are usually the greatest in the range of 0.05% to 1.0% filterable solids. Filterable solids that average in particle size about 20 microns& are non-compressible are very easy for this filtration process. Some feeds have been all sub-micron in particle size. A 1/8 inch thick cake is considered to be very thick. The usual cake is between 13/2 and 1/16 inch thick. A new line of injection molded plastic filter plates were developed for use with the reversible cake filtration process. The first commercial sized installation of this system was made 3 years ago in the Wakefield Y.M.C.A. swimming pool. Over 70 filters ranging in size from one plate to 63 plates have been produced. In addition to the process advantages there are the low cost and corrosion resistance advantages of the plastic plates.

Jan 1, 1962

By L. Barry Phelps

The application of an open-pit Materials Handling Simulator (OPMHS) to analyze mine planning and scheduling problems in large surface mines is discussed. The mine chosen for this application employed a large stripping dragline working in tandem with a shovel-truck haulback system for removing overburden. Large bottom-dump trucks were employed behind a coal loading shovel to transport the exposed coal out of the pit. Specifically, the current operations and the recommendations for short term and long term improvements were simulated on OPMHS. The effects of changing the operating parameters of the equipment on the total system were evaluated. Several alternatives were also studied for the best use of the existing equipment if the current operating parameters could not be improved upon. The results of the application are discussed.

Jan 1, 1978

By Aline Tavares

This paper describes the investigative studies carried out at Vale´s Center of Mineral Development (CDM) for a nickel sulfide deposit aiming to develop an adequate flotation flowsheet. The CDM facilities comprises of very well equipped laboratories to develop hydrometallurgical, comminution, flotation, physical separation processes, besides chemical and mineralogical laboratories, that are required to accomplish pre-feasibility studies, new process routes developments and, eventually, brownfield projects. Close association of the flotation group with the geometallurgy and the mineralogy teams play a key role during greenfield project development. Most of the information required by process engineers responsible for the flowsheet development can be provided by the mineralogy team and its mineralogical laboratory at CDM. During the flowsheet development of this nickel sulfide deposit, two ore types were identified as the most abundant in the deposit, named biotite-chlorite hydrothermalite (HID) and magnetite hydrothermalite (MAG HID). Six samples were selected for the investigative studies based on this initial information. Nickel grade varied from 0.39% to 1.95%. The main nickel-bearing minerals were millerite and pentlandite whereas the main non-sulphide gangue minerals were quartz, plagioclase, biotite, chlorite, actinolite, and/or magnetite. Electron microprobe (EMP) identified the presence of nickel in solid solution in gangue minerals such as biotite, chlorite, and actinolite. Nickel deportment in silicates varied from 3% to almost 40%. Magnesium was distributed in biotite and chlorite, except in sample MAG HID, in which talc was responsible for almost 50% of the Mg content. Liberation studies indicated that the optimum feed grind size was around 150µm and that pyrite occurred highly associated to the nickel sulfides. The flotation tests were planned based on the information provided by the mineralogical data. Rougher flotation tests indicated that the optimum P80 of the primary grind was 212µm for the HID type and 150µm for the MAG HID. From the reagents tested, amyl xanthate proved to be the most efficient in the recovery of the sulfides. In the MAG HID sample talc was well depressed by dosing 600g/t of CMC. Nickel recoveries in the rougher stage were lower than 90% due to the nickel distributed in silicates. However, sulfur recovery was around 95%, indicating high recovery of the total sulfides. Open circuit and locked cycle tests were conducted to evaluate the effect of the regrind size in the nickel grade and recovery (P80 of 44µm and 20µm). Nickel recovery decreased from 70% to 65% when finer regrind size was tested. Although nickel recovery decreased by 5%, the finer regrind size lead to a higher Ni grade (from 11% to 23%Ni) and lower fluorine grade (from 1138ppm to 700ppm) in the concentrate. Keywords: nickel sulfide, flotation, mineralogical characterization, flowsheet development

Sep 1, 2012

By J F. C L Costa, J C. Koppe, C Diedrich

Currently mineral resources evaluation is firstly expressed in terms of volume. Next the resources are transformed into tonnes by using an average bulk density applied to the whole deposit or, in some other circumstances, various different densities to distinct geological domains. Previous work in uranium, copper and nickel deposits used linear correlation between grades and bulk density to derive the density. Geophysics methods are also another good way to obtain density indirectly.These approaches do not take into account that two samples with the same grade but with different bulk densities can characterise different sample supports, leading to severe bias in grade and tonne estimates. It is important that the systematic measurements of bulk density are included into the estimation process, particularly when density is not correlated with the grades. Additionally, the extra time and costs involved in obtaining the bulk density data have made the mining industry disregard it.This study reports the impact in resource estimates by using a methodology that includes the bulk density variability. It involves the determination of a variability model for the bulk density and another model for the composite that was weighted by density as well as by its length. Next, these variables are estimated by kriging and the final grade estimates are obtained. The tonnages are obtained with the bulk density estimates. The conventional methodology was also applied and both estimates are compared to the reconciliation data from a major copper deposit. The results show a significant difference between the tonnage and grade estimates obtained from these two methodologies.The results show that considering density variability when compositing leads to a more accurate methodology resulting in better grade and tonnage estimates locally and globally.

Sep 26, 2011

By E. Farrokh

CSM and NTNU models are among the most commonly used models in TBM performance evaluation. Due to increasing application of TBM in different tunneling conditions, modification became necessary for these models. Sensitivity analyses on these two models indicate that both models are very sensitive to machine characteristics. Analyses performed on CSM database for cutter load and penetration rate prediction indicate while the r-square of the CSM model is reasonably high for the predicted cutterload, the r-square value for the penetration is low. In order to increase prediction capability of CSM model for penetration rate the model was reevaluated using non-dimensional analysis and the original database of Colorado school of mines. NTNU model is evaluated using Monte Carlo simulation and regression analysis. The results of analyses indicate that the majority of the variation of the penetration in NTNU model can be explained by only three parameters. This might indicate that the effects of other factors are overshadowed and it is worthy to reevaluate NTNU model using original database and more updated statistical methods to avoid overlapping of different parameters correlations.

Feb 23, 2014

By W Assibey-Bonsu

The paper provides a brief review of the multivariate uniform conditioning and the localised multivariate uniform conditioning techniques and presents a case study based on a porphyry copper gold deposit in Peru. Two other important scenarios have been investigated and will be particularly emphasised: The recovered selective mining unit (SMU)s depend on a combination of copper and gold content, which can be expressed by means of ænet smelter returnsÆ (NSR). Two approaches are compared. Firstly, the application of a composite cut-off on NSR on the joint distribution of each grade and the application of uniform conditioning to three variables is investigated, ie for the first approach NSR is used as the main variable. The second approach considers copper as the main variable. In the case of multiple domains the procedure used to apply the technique to process mixed panels is clarified and recommendations are made.

Sep 26, 2011