Search Documents

By Peter Kreisman

This paper and four other papers on the MEQB Regional Copper-Nickel Study, presented today at the 1980 SME-AIME Fall Meeting are based on four years of extensive inter-disciplinary research and impact analysis supported largely by the Legislative Commission on Minnesota Resources. This study produced over 180 technical reports, the results of which are summarized in an Executive Summary available from the Minnesota State Planning Agency, St. Paul, Minnesota. Those wishing to examine the many scientific, engineering, environmental, social or economic issues addressed by the study are encouraged to obtain a copy of the executive summary. The executive summary includes a bibliography of all technical reports produced by the Regional Copper-Nickel Study and describes the five-volume, 26 chapter Regional Copper-Nickel Study Report.

Jan 1, 1980

By K Lee, L Mann, J Bygrave, G Sheldon

Ausmelt is supplying commercial quantities of an alkyl hydroxamate flotation collector AM28 for flotation of oxide and supergene base metal ores and tailings. AM28 is a non-hazardous product used as a ten per cent to 50 per cent solution in dilute potassium hydroxide. It is a selective flotation collector for oxide or oxidised base metal minerals and replaces conventional sulfidisation for oxide mineral flotation. At Radio Hill, the AM28 is used in conjunction with traditional sulfide collectors, which allows simultaneous flotation of oxide and sulfide copper minerals. The Fox Resources Radio Hill copper concentrator near Karratha, Western Australia, is currently configured to treat supergene copper ore sourced from the West Whundo open pit. This Archean VMS type copper deposit has been deformed and remobilised with uplift, erosion and weathering to form a significant supergene zone. The sulfide copper minerals present in the upper zone are digenite and chalcocite with lesser chalcopyrite and covellite. Oxide copper minerals present include cuprite, with lesser malachite and azurite. Gangue minerals include quartz, talc and chlorite. Plant trials at Radio Hill are reported for supergene West Whundo ore, where the AM28 was stage added into the circuit at nominally 80 g/t. Plant data over three months shows the copper recovery increased consistently from around 50 - 60 per cent to above 70 per cent when AM28 was added. This has been proven statistically. The grade of the concentrate was consistent with and without AM28, at nominally 22 - 24 per cent copper.

Jan 1, 2007

By Libby R. Ricafort, Nonato S. Retardo, Jose B. Anievas

This paper shows the metallurgical test results that led to the design of the heap leach facilities of Philex Mining Corporation. The design incorporates a water management model as process solution circulation is excessive with high rainfall intensity in the area. This poses problems in the operations requiring stringent controls than would be necessary in a less severe environment. The corporate perspective embraces on environmentally-sound mineral development. A budget is always provided to environmental management making certain that no industrial development is moved forward at the expense of the environment.

Jan 1, 1996

By Admilson José Borges

Substituir todo o texto de orientação deste Template pelo conteúdo de seu trabalho. Inserir o texto com no máximo 1.500 caracteres (200 palavras), sem uso de parágrafos. Deve conter, de maneira concisa, o objetivo, a metodologia, os resultados e as conclusões do trabalhoO presente trabalho buscou identificar as principais oportunidades de melhoria na operação de carregamento de vagões no pátio de produtos na mina de Alegria em Mariana, com o propósito de aperfeiçoar, estabilizar e padronizar o processo, consequentemente aumentando-se a produtividade das pás carregadeiras CAT 990, minimizando o tempo de estadia do trem no pátio de produtos e o custo da operação. A elaboração do estudo no setor de expedição de produtos foi baseada em decisões orientadas pela ferramenta de melhoria contínua Seis Sigma e em análises de fatos e dados. Os resultados foram validados através da superação da meta estabelecida para o projeto, onde o objetivo inicial foi aumentar em 8,1% a produtividade do equipamento em relação ao valor atual, porém conseguiu-se atingir o valor de 23,5% com um ganho anual de R$1,34 milhões.

Oct 30, 2017

By Emre Turk, Suat Gullu, Candan Gokceoglu, Ahmet Sirri, Asli Can

In this study, the ground improvement application applied under the live railway bridge's approach embankments in Sivas, Türkiye was investigated as a case study. The soil profile is mainly composed of orangish conglomerate, clay, silty sandy clay, and under claystone, and mudstone units in the study area. As a soil improvement method, the Deep Soil Mixing (DSM) technique based on the principle of simultaneous mixing the ground while injecting with the water-cement mix, was selected. The application of DSM columns is designed to be 45 degrees horizontal, in order to reach the deepest point of the soft clay units for better improvement against settlement. The core samples were taken from the DSM columns and the compressive strength tests were performed in the laboratory. The results were higher than the minimum designed values. It means that inclined DSM columns were applied successfully, and the excessive settlement problem was solved.

Oct 1, 2022

By Wantae Kim, Jaechun Lee, Tatsuya Oki, Sungbaek Cho, Sangbae Kim

"Effect of attrition scrubbing on the recovery of platinum group metals(PGMs) from automotive catalytic converter was discussed. The attrition scrubbing as comminution and separation process was effective for the recovery of the catalyst layer, ?-alumina, from ceramic supporting matrix, cordierite, by physical impact and shearing action between particles in the scrubbing vessel. The catalyst layer was dislodged from the surface of the supporting matrix into fine particles less than 45µm by attrition scrubbing. The production of fine fraction less than 45µm increased as the residence time for attrition scrubbing increased. The fine fraction obtained at the residence time of 40min contained 19.25% CeO2, 1.93% ZrO2 and 418.8ppp PGMs. The recovery of ?-alumina in the fine fraction increased as the residence time increased. Simultaneously, the recoveries of CeO2, ZrO2 and PGMs increased and reached up to 82.9% CeO2, 78.7% ZrO2 and 78.9% PGMs at the attrition scrubbing time of 40min. The production of the fine fraction and recovery of ?- alumina increased when the solid concentration and initial feed size increased.IntroductionThe automobile catalytic converters contain appreciable amount of PGMs. Currently several million tons of used catalytic converters are disposed annually worldwide, each containing about 0.5-1g of platinum and 1-2g of all PGMs1). The recovery technologies of PGMs from spent catalytic converters have been thoroughly reviewed by numerous researchers since last decades. Two types of methods, wet and dry processes, have been commercially operated. In the wet process, the PGMs on the spent catalytic converters were dissolved mostly in the form of chlorocomplex, MCl6 2-, by contacting with aqueous solutions. Subsequently the resulting solutions are treated to concentrate and the precious metal ions are reduced by introducing metals such as Al, Fe and Zn in the concentrated system2). In the dry process, the spent catalytic converters are melted, in some case with CaO, at an elevated temperature to produce a low viscous slag. The PGMs in the melt are separated by allowing them to adsorb on Fe or Cu having high specific gravity7). Although highly pure precious metals could be obtainable, the recovery technologies of PGMs currently operated seem not to be cost-effective since PGMs embedded in these types of catalytic converters are present in very small quantities."

Jan 1, 2008

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"The use of steel screw piles has greatly increased in recent years because of the advancement in the installation mechanism and its performance under compressive, uplift and lateral loads. In a steel pile system, the strength of pile material limits the end bearing resistance of the pile due to strong subsurface conditions. The installation mechanism of screw pile can reduce the end bearing resistance due to the torque and axial force. However, if the installation mechanism does not reduce the bearing resistance of the pile, another important factor that can reduce its performance is the strength of the helix/wing plate. In this study, the effect of wing plate deformation on the performance of single helix/wing plate pile bearing resistance investigated. A model ground was used to investigate the effect of wing plate deformation. Dry Toyoura sand was used as a ground material and was compacted to denser states of 80% and 92%. The shaft and wing plate material of the pile was the same to actual piles that are used nowadays in Japan. A series of load tests were performed with different wing plate diameters and thicknesses. It was observed that deflection in the wing plate reduces the bearing resistance of the pile. The increase in the thickness of the wing plate was seen to restore the reduced pile resistance due to deflection. It was also observed from the experimental results that the ratio of wing plate diameter to shaft diameter (Dw/Ds) greatly affects the deformation of wing plates, which ultimately affects the end bearing resistance of the pile. The results obtained in this research suggest that the outstand length (Lw) of wing plate should be less than 5.6 times the thickness of wing plate for piles having a large Dw/Ds ratio under strong ground conditions.INTRODUCTIONThe first use of screw pile was almost 180 years ago by Alexander Mitchell. He patented his invention in 1833 with the name “Screw Pile”, and used it for ship moorings. The use of screw piles has since been adopted in various areas such as lighthouses, fencing for agriculture and marine structures. The use of screw piles in civil works started in 1985, after the invention of the hydraulic torque motor, as it eases the installation process. Nowadays, screw piles are used in the foundation of transmission towers, elevators, buildings and many other civil structures.Screw pile has an edge over other steel pile systems due to its high bearing, uplift and lateral resistance. The end bearing resistance of screw pile depends on installation, strength of subsurface material and the pile material. The screw pile is installed by applying torque and axial force. The pile torsional strength should be more than the applied torque and axial force to avoid deformation before reaching the final depth."

Jan 1, 2015

By R. Weideman, K. du Preez

Biological sulfate reduction has become a successful treatment alternative for acid mine drainage and Mintek is developing biological processes for treatment of highsulfate mine waters. Treatment of these high-sulfate waters is achieved by sulfatereducing bacteria that reduce sulfate to produce sulfide as a product, in the form of H2S and HS− at neutral pH. This introduces the opportunity to apply treated effluents from biological treatment processes for the recovery of metals, such as copper, from metallurgical waste streams. This study models the kinetics of copper sulfide precipitation from a complex bioleach liquor. The results indicated a rapid rate of reaction and the formation of covellite, suggesting the potential to use biogenic sulfide to recover copper as a metal sulfide product.

Jan 1, 2023

By Fábio de Oliveira Braga

A proteção balística contra projéteis de alta energia, como o 7,62 mm, é mais eficientemente realizada por meio de sistemas de blindagem multicamada (SBM). Estes são formados, em geral, por uma camada frontal de cerâmica, uma camada intermediária de tecido sintético ou de compósito, e uma camada posterior de um metal dúctil. Em trabalho recente, Monteiro et al. (2016) estudaram um SBM com camada intermediária formada por compósito reforçado com tecido de rami em substituição a um laminado tecido de aramida. Eles obtiveram resultados satisfatórios com boa redução de custo. No presente trabalho, foram investigadas fibras de rami in-natura como substituição ao tecido de rami na camada intermediária compósita. Os resultados foram comparados ao desempenho de um compósito reforçado com 30% de tecido de aramida, bem como aos resultados anteriores. Observou-se que a utilização dos compósitos reforçados com fibras de rami manteve o bom desempenho do SBM, com um custo cerca de 5 vezes menor que o SBM com aramida, e 60% menor que com tecido de rami.

Oct 30, 2017

By Bruno Valladão Fraga

Esse trabalho tem como objetivo apresentar a estratégia adotada para a migração dos sistemas de otimização de processo dos três Altos Fornos da ArcelorMittal Tubarão. O desenvolvimento dos novos sistemas é baseado no Plano Diretor de Tecnologia de Automação (PDTA) que definiu a arquitetura, tecnologias e elaborou o Framework como base das aplicações. Para a migração dos sistemas foi elaborada uma especificação detalhada de todos os módulos e funcionalidades existentes, permitindo dessa forma a criação de uma camada com as principais regras de negócios relativas ao processo para serem reutilizados em todos os Altos Fornos. Essa camada deu origem ao Framework dos Altos Fornos. Os resultados obtidos já podem ser vistos nos três sistemas migrados para a nova plataforma, com um alto desempenho e estabilidade, garantido dessa forma a segurança operacional objetivada.

Aug 17, 2017

By V. Nasri, P. Jarast, M. Bakhshi

The Montreal metro Blue Line Extension toward the northeast consists of the construction of five new underground stations. The project includes 6 kilometers of the tunnel which will be constructed using a Tunnel Boring Machine (TBM). In line with the commitment to integrating sustainability best practices, Envision verification is pursued this project. The Envision reference framework was developed to cover all the sustainable development aspects of an infrastructure project and each phase of its life cycle (planning, design, construction, operations and maintenance, and end-of-life). As a part of this endeavor, low-carbon concrete and shotcrete mixtures are proposed for the linings of TBM and SEM tunnels as well as stations and auxiliary structures. The CO2 emission of the low-carbon concrete and shotcrete mixtures were compared with their typical mixtures and the total CO2 emissions reduction related to the tunnel lining is determined. The study is of strategic significance for achieving emission reduction in the tunnel industry.

Jun 13, 2023

By Junfu Chen, Jiann-Yang Hwang, Yong Zhou, Lijun Lu, Likun Lia, Jixiong Liu

The sheet-like NiS-ZnS heterostructured composites were prepared by the microwave hydrothermal. The fabrication of the heterojunctions broadened the range of light response of ZnS. The photoexcited electrons of ZnS migrated to the redox potential of NiS/Ni2S under visible light irradiation, which can facilitate the effective separation of photogenerated electrons and holes in space. The visible photocatalytic activity towards hydrogen production for NiS/ZnS nanosheet heterostructed composites without co-catalyst achieved 0.28 mmol h–1, and the quantum efficiency was up to 18.6% under the wavelength with 420 nm visible light irradiation.

Jan 1, 2015

By J Wheeler

The benefits of fine size separation in magnetite concentration are detailed focusing on published research from various iron ore producers. Basic principles of fine sizing and advancements in screening technology are addressed. A chronological review of research is used to show the evolution of fine sizing applications in the industry, starting with studies that demonstrated the benefit of using fine screens to produce consistent lower silica concentrates, followed by improvements in fine sizing equipment that have made effi cient screen classification in ball mill circuits practical. Case studies are used to demonstrate how positive sizing with screens can be used to significantly shift concentrate ‘grind/grade’ relationships.

Jul 11, 2011

By M. Reda

Inorganic oxidizing agents of the type MeOx-z such as Chromate, Vanadate, Tungstate, and Molybdate... etc. are widely used as corrosion inhibitor. In non acidic solution these oxidizing agent are reduced on the surface of the meta, according to OX + m e + p H20 Red + n OH" In which y = (n-m)/m. The purpose of this publication is to show that for many metals the value of y for any oxidizing agent determines the possibility of that oxidizing agent being an inhibitor or activator for the corrosion process. The inhibition efficiency for other ions such as Pertecnetate and Tellurate which have not been extensively studied can be predicted. A mathematical, equation was derived to express the relationship among the concentration of oxidizing agent, degree of retardation of the corrosion process I cord cor ° (ratio of corrosion current in the solution containing inhibitor to the base solution) , ionic strength of the solution and the coefficient y. The validity of y and the mathematical, equation were verified by many experimental, works on various metals such as zinc, aluminum and steel. Al, the above research works are based on the published research works of Prof. Mikhailoviskii (from 1979 til, 1998) from the Russian Academy of Science.

Jan 1, 2010

Jan 11, 1951

By C. Geier

Our national interests are best served by having well-trained first responders available for rapid response to emergency situations in underground mines. However, recent mine disasters have indicated that focused training on hazard recognition, decision making, leadership, and incident command center protocols needs to be incorporated into a comprehensive training plan for all personnel involved in a mine rescue. Currently, there are very few training opportunities for the mining professionals responsible for making the crucial decisions needed during a mine emergency. With recent technical advances, it is now feasible to use a computer-based simulator to train mine rescue personnel for mine emergencies in their mine or any other mine at a convenient location without interrupting normal mining operations. This simulated environment teaches underground search and rescue procedures, communications, and decision making based on real-time information and hazard recognition. Since 2010, the Colorado School of Mines (CSM) has offered computer simulated mine rescue training using an incident command center (ICC) directed towards enhancing decision making and communication skills. To support this training, CSM partnered with Rite Solutions, Inc. to modify, enhance, and create simulation software for mine rescue applications. The focus of this partnership is to modify existing simulation technology to address the unique nature of underground rescue operations, make it applicable to any underground operation, create generic scenarios, and develop customized computer simulations, including scenarios, for specific sites. Need The CSM mine rescue computer simulator helps mine rescue teams train for mine disasters where they would be deployed for the rescue and recovery of a mine. It provides additional, readily accessible opportunities to train without affecting mining operations. While the simulator lacks the physical demands of a rescue situation, it is very effective for teaching mine rescue procedures as rescuers seamlessly walk through the process and work out issues before going underground. The mine rescue simulator also introduces students to coordination through an ICC which stresses the use of effective communication and hones decision making skills. Most of the mine rescue teams participating in this study had never trained with an ICC controlling the actions of the mine rescue team making this an extremely valuable training opportunity. In addition, the mine rescue computer simulator allows instructors to modify mine rescue scenarios and tailor the scenarios to each team?s individual needs resulting in a more versatile training experience. The goal is to ensure that all teams receive the maximum benefit from each training session.

Feb 27, 2013

Two new inorganic-organic hybrid polymers, Al(OH)3-polyacrylamide (Al(OH)3-PAM) and Mg(OH)2-polyacrylamide (Mg(OH)2-PAM) were synthesized and successfully applied for the treatment of oil sand tailings. The results indicate that both Mg(OH)2-PAM and Al(OH)3-PAM were unaffected by the change in pH, and could be applied to oil sand tailings with varying sand-to-fine ratio (SFR). The optimum dosages for the Mg(OH)2-PAM and Al(OH)3-PAM were about 330 g/ton and 650 g/ton, respectively for SFR 3.75. The flocculated oil sand tailings dewater quickly producing 66-68% solids. The flocculated tailings produced similar filtration rate before and after shear. Mg(OH)2-PAM treated oil sand tailings produced twice the filtration rates (220 ml/min) compared with Al(OH)3-PAM. This study clearly indicates that Mg(OH)2-PAM and Al(OH)3-PAM is a viable solution while decreasing the mass-production of tailings and increasing the rate of water-recycle.

Jan 1, 2012

MINING METHODS W. J. COULTER, Chairman P. B. BUCKY, Vice-Chairman CLYDE E. WEED, Vice-Chairman ROBERT S. PALMER, Secretary Alluvial Mining CLINTON BERNARD O. B. PERRY NORMAN CLEAVELAND C. M. ROMANOWITZ R. B. EARLING J. B. STAPLER BENERE H. GRANTCHARLES THURMAN Open-Cut Mining Iron. A. D. CHISHOLM EARL E. RUNNER G. E. DIEHL G. E. LEVEQUE P. G. HARRISON SIMPSON RICHEY W. A. STERLING

Jan 1, 1943

Jan 1, 1943

Jan 1, 1926