Search Documents

By R. I. Jaffee, C. T. Sims, C. M. Craighead

The fabrication of rhenium metal by powder metallurgy techniques is discussed. The following physical and mechanical properties have been measured and are reported: lattice constants, melting point, electrical resistivity, thermal expansion, spectral emissivity, modulus of elasticity, tensile properties and ductility at room and elevated temperatures, work hardening, recrystallization, grain growth, and oxidation resistance. IT is only occasionally that a metal reaches present-day technology with as little known about its properties as element No. 75, rhenium. Relatively scarce to date, it has been studied only infrequently and used less. Previous work on rhenium has been carried out primarily by European scientists. However, realization that rhenium occurs in commercial quantities in the United States recently has focused attention on this metal. Rhenium is a very dense high melting hexagonal-close-packed metal. Like tungsten and molybdenum, its highest oxide is volatile. However, when protected by reducing or inert atmospheres, its strength at high temperatures is greater than that of tungsten. Rhenium work hardens more than any other known pure metal, but, on annealing, becomes quite soft and ductile. Its vapor pressure is approximately that of tantalum, but it does not enter into the so-called "water cycle" nearly as readily as does tungsten. (The water cycle is a deleterious phenomenon causing blackening of lamp bulbs and vacuum tubes with subsequent failure of the filaments.) These and other properties, some already known and some found as a result of the current researches, have indicated that rhenium has many potential uses, primarily of an electrical or electronic nature. Rhenium or its alloys soon may be found in service as electron-tube filaments, cathodic emitters, or as electrical contact materials. In addition, rhenium or its alloys have potential use in such devices as high temperature thermocouples, and high wear-resistant parts such as precision instrument points. Rhenium, in the form of potassium perrhenate, was made available for this study by the Kennecott Copper Corp. The potassium perrhenate was reduced to rhenium metal in two stages, accompanied by leaching to remove potassium in the form of hydroxide. This impure metal was then oxidized to rhenium heptoxide and dissolved in water. The solution was neutralized with ammonium hydroxide to produce highly purified ammonium perrhenate, a typical analysis of which is shown in Table I. The ammonium perrhenate was ground to —325 mesh in a rubber-lined ball mill with Burundum balls. This operation caused a certain amount of impurity pickup, as reflected in the rhenium analysis shown in Table I. The fine ammonium perrhenate was reduced to metal with hydrogen. Particle size of the powder ranged from 1 to 25 microns, as illustrated by Fig. 1.

Jan 1, 1956

By H. D. Outmans

In steady vertical flow, the interface of an immiscible liquid-liquid displacement is horizontal for any flow rate below the critical. In nonvertical flow, however, the shape of the interface in the steady state does depend on the flow rate, and the purpose of this paper is to calculate the unsteady interfaces during the transition of one steady state of flow to another. A knowledge of these transient interfaces is of considerable importance in reservoir engineering where the calculation of breakthrough recovery depends on the instant the interface reaches the producing wells and on the shape of the interface at that time. Although the emphasis is put on transient interlaces, which eventually approach stable equilibrium, it is shown that if the displacement exceeds a critical rate no equilibrium is possible. The interface is then unstable and viscous fingers are formed during the displacement. The critical rate and the shape of the transient and equilibrium interfaces are affected by the effective interfacial tension; but since this effective interfacial tension appears in the calculations only in combination with the inverse square of the thickness of the medium, its effect in the reservoir would appear to be negligible compared to its significance in model experiments. INTRODUCTION Stability criteria and the early growth of interfacial disturbances in a plane parallel to the boundaries of a dipping formation in which oil is displaced by an incompressible fluid were described in a previous paper.l This type of instability is significant in thin reservoirs. However, if the reservoir has appreciable thickness, then interfacial stability in vertical planes, normal to the upper and lower boundaries, also becomes important (the displacement is supposed to be parallel to these vertical planes). The difference between the two stability problems is that, in the first case, the intersections of the interface with planes parallel to the boundaries are normal to the direction of the displacement; in the second case, the intersections, this time with vertical planes, are not normal to the displacement. Instead, they are tilted at an angle which depends on the displacement rate. The tilt of steady interfaces was calculated by Dietz2 who also determined the critical rate of displacement for stability in the vertical plane by assuming that this rate would coincide with an interfacial tilt equal to the dip of the formation. The critical rate thus calculated is the same as has been found for thin reservoirs (see Eq. 1.1 of Ref. 1 and of the present paper). Dietz's calculation of the stable tilt was verified by laboratory experiments and the agreement was found to be fairly good.3 It is doubtful, however, that stable tilts actually exist in the reservoir because a change in production rate is not followed by an instantaneous adjustment of the interface to the new rate but, rather, by a transition period during which the interface changes from one equilibrium tilt to the other. The principal objective of this paper has been to describe these transient interfaces without putting any restrictions on the flow conditions or the shape of the interface, as had been done previously. The second objective was to compute the critical velocity, taking into account capillary effects, and the third was to evaluate, at least qualitatively, the shape of the front at rates above the critical, again without making the simplifying assumptions introduced by previous investigators.2,3 In the following sections two examples are given of the calculation of interfacial motion. The first describes this motion for an initially horizontal interface in a dipping layer, and the second for a vertical interface in a horizontal layer. The mathematical formulation of the problem is nonlinear in the boundary conditions, and this prohibits its solution in closed form. Instead, the solution is obtained in the form of higher-order approximations. 1 Before proceeding to a description of the mathematical model, however, we define two quantities

By Lawrence F. Johnsen

Six case histories are presented in which tall, slender high rises are supported on high capacity minicaissons. The recent development of a high strength rebar cage has resulted in compressive loads of up to 3400 kips on 24 inch diameter minicaissons. Provisions in the pending NYC building code will allow borehole video inspection in lieu of load testing. The ?new? technology results from the marriage of several well established methods: rotary duplex well drilling, high capacity micropiles and high capacity reinforced concrete building columns.

Jan 1, 2007

By G. M. Schwartz, G. A. Thiel

THE first record of the quarrying of dimension stone in Minnesota dates back to 1820 when limestone was quarried locally for part of old Fort Snelling. Limestone quarries were operated at Stillwater, Mankato, and Winona as early as 1854. Granite was quarried first at St. Cloud in 1868, and within a few years thousands of tons were shipped to widespread points. Rough dimension stone for large buildings furnished the first important market, but beginning in 1886 paving blocks were in demand. The largest shipment was in 1888, when 1925 cars were shipped from the St. Cloud area. Quartzite was quarried first at New Ulm in 1859 and somewhat later at Pipestone and elsewhere in southwestern Minnesota: The productive dolomite quarries at Kasota were opened first in 1868 and have continued as large producers of a variety of stone to the present time. At present, the industry is controlled by relatively few operators, and for that reason detailed figures on dimension stone are not released for publication. A general idea may be obtained from the data in the Minerals Yearbook for 1948. The figures for total stone produced in Minnesota are 1,804,000 tons valued at $5,090,652. Probably the largest item in the latter figure is received from dimension stone. A better idea of the situation, in relation to the country as a whole may be gained by using the data for 1930 when more companies were operating in Minnesota, and complete figures were published. In that year Minnesota produced granite valued at $2,668,119 and ranked third among the states in value. Minnesota's production of granite was almost exclusively for dimension stone. In the same year Minnesota produced 300,000 tons of limestone (dolomite) valued at $840,860, and this likewise was mainly dimension stone. In finished limestone Minnesota ranked second among the states in 1930. Sandstone and minor amounts of quartzite are the only other dimension stones that have been produced in Minnesota, but the quarries are now inactive. The commercial stones of Minnesota have been described in two reports by Bowled and by Thiel and Dutton.2 The early history of quarrying in Minnesota and extensive notes on the various rocks are given by N. H. Winchell.3 Small limestone and dolomite quarries were numerous throughout the area of Paleozoic rocks in southeastern Minnesota. Early production was largely dimension stone. With the increased use of Portland cement, most of these ceased production, and today only those at Kasota and Winona remain in operation. In recent years many quarries have reopened and new ones started, but these are devoted to the production of crushed rock and agricultural lime. As the application of modern quarrying and finishing methods increased, small companies in the granite business have dropped out, and the remaining companies have modernized their plants, purchased old quarries, and opened up new ones, thus furnishing a wide variety of granites suitable for most of the customary uses. It is the purpose of this review to present notes on' the geology and operations of each of the quarries now operating within the state. Granites and Related Igneous Rocks The term granite as used in this report includes granites, gneisses, diorites, gabbros, and other igneous rocks. The granites of greatest economic importance are found in three widely separated regions, see Fig. 1. 1-Central Minnesota in the region of the city of St. Cloud, 2-the upper Minnesota River valley region, 3-the northeastern portion of the state, commonly referred to as the Arrowhead region. The St. Cloud Region: The rocks of the St. Cloud region are mainly granites and related rock types such as monzonites and quartz diorites. The stones may be grouped into three major types, namely, pink granite, red granite and gray granite. Most of the pink granite occurs in the area to the southwest of St. Cloud. The rock is best described as stone with large pink crystals set in a finer grained black and white background. The minerals of the matrix occur in remarkably uniform sizes, and the pink crystals are sufficiently uniform in. their dis-

Jan 1, 1952

By R. Taggart, D. H. Polonis, J. C. McMillan

Thin foil electron microscopy techniques have been used to study the micros tructure of a Ti- 7.5 wt pct vanadium alloy in the quenched and aged cond_itions. Selected area diffraction has identified a (1011) twinning mode accompanying the martens ite t9.an.sfo?rn~ation. Precipitation of the 0 phase during the aging of quenched alloys has been obsevced to occuv in the form of plates and needles with preferential growth along the (1120) direction in the a' matrix. In the present work, the micro structures of quenched and aged alloys of the 0 isomorphous Ti-V system have been investigated by means of thin-foil electron-microscopy techniques. Most of the previous studies of martensitic phases in titanium-base alloys have utilized optical microscopy and X-ray diffraction techniques. The application of transmission electron microscopy is more recent, and only a few such studies have been reported.1-5 This paper is concerned particularly with the crystallographic nature of substructures formed in the martensitic a' plates. The early stages of aging or tempering have also been examined to determine the modes of precipitation from the martensitic solid solutions. Such information is essential in studying strengthening mechanisms and in determining the feasibility of high-strength rnartensitic alloys based on titanium. Liu and Margolin6 reported several types of substructures within the martensitic plates of quenched Ti-Mn alloys. It was later suggested by Liu7 that the structure of martensitic plates might be very complex and not single crystals as normally assumed. The sub-markings could not be identified with the two possible habit-plane orientations {334}ß and {344}ß, and it was not positively determined whether they are associated with mechanical twinning. The recent studies by Armitage5 on titanium martensites in a variety of commercial alloys have indicated that twinning does not generally accompany the transformation. This observation is in accordance with the Mackenzie and Bowles model for the transformation in pure titanium8 which suggests that twinning is not to be expected. However, a number of other recent investigators have reported twinlike substructures in the martensitic plates of several titanium systems including commercia1 titanium,2,3 Ti-Cu,5,9 Ti-Ta,1 and the commercial alloy Ti-8A1-1Mo-1V. Blackburn* has reported that the structure of quenched Ti-8A1-1Mo-1V depends on the prior solution temperature. He identified two types of martensitic structures, one of which is described as a heavily faulted hcp or twinned fcc structure and the other an hcp structure with a high internal dislocation density. The latter type exhibited some twinning with a (1011) twin plane. EXPERIMENTAL PROCEDURES AND RESULTS The alloy used in the present work was a 7.5 wt pct V alloy that was prepared by conventional arc-melting techniques. This alloy composition was selected

Jan 1, 1968

By R T. A MacGillivray, S B. Curtis

Bacteriophage (phage) are viruses that infect bacteria. Protein coatings on the surface of the phage particle can be genetically engineered so that they bind to inorganic molecules. The filamentous phage particle is about 930 nanometres in length and 6.5 nanometres in diameter and consists of a single-stranded molecule of DNA surrounded by five different coat protein molecules denoted P3, P6, P7, P8 and P9. Peptide sequences in the P3 coat protein that bind to sphalerite and chalcopyrite have been identified. The binding is selective; phage with specific P3 peptide sequences bind to minerals but do not bind to silica or to pyrite. Two peptide sequences in the P8 coat protein that bind selectively to chalcopyrite and pyrite have also been identified. The amino acids in the P8 binding sequences are hydrophilic and thus a coating of a mineral particle with phage having these peptide sequences may render the particle hydrophilic. Experiments are underway to confirm this. Phage are relatively easy to grow and are not living organisms requiring an energy source to maintain life. Phage can also tolerate a range of pH and temperatures. Given this, and the ability to indentify phage coat proteins that bind selectively to a variety of inorganic molecules, phage have the potential to be useful tools in mineral processing and waste treatment.

Jan 1, 2008

By L. L. Newman

As soon as the Congress recognized the alarming rate at which our domestic oil resources were being depleted during the war, it took action to step up the rate of research and development which the Bureau of Mines had been conducting for several years on the production of synthetic liquid fuels from coals. Under Public Law 290, approved April 5, 1944, funds were authorized for the Bureau to proceed with research, development, design and construction of demonstration plants for the hydrogenation of coal, the synthesis of oil from carbon monoxide and hydrogen, and the distillation of oil from shale. During the latter part of 1944, when it became evident that the collapse of Germany was near, a Technical Oil Mission was organized to study the Ger- man techniques of synthetic oil production. Since the cost of hydrogen or synthesis gas is one of the major factors of expense in the operation of hydrogenation or synthesis gas processes, the Bureau of Mines considered it of prime importance to include on the mission gas engineers whose instructions were to examine closely the methods employed by the Germans in solving the problem of providing low- cost hydrogen or synthesis gas for their very extensive operations on synthetic liquid fuels. The Solid Fuels Mission and the Utilities Mission, as well as the Army and Navy Missions, also included teams for the study of German gas production. Although their objectives naturally differed from those of the Technical Oil Mission and from each other, it was recognized that there was considerable overlapping of their fields of investigation. Duplication of effort, however, was largely avoided through the close cooperation between the group leaders of these missions. For example, although I went to Europe as a member of the Technical Oil Mission, my first German assignment was actually made by Dr. Harry F. Yancey, leader of the Solid Fuels Mission- to investigate the brown-coal gasification methods in central Germany. The art of gasification in the United States and England, and to a large extent in the proximity of the coking-coal regions of Germany and the rest of continental Europe, depends essentially on two stages of operation; namely, carbonization and intermittent water-gas generation. As far as the United States is concerned, complete gasification in a single stage of operation is rarely practiced, except in gas-producer operations where the product is a relatively lean gas consumed close to the point of manufacture, and for water-gas production with anthracite as a generator fuel. Complete gasification of bituminous coal has been the subject of numerous investigations. Many relatively simple modifications of the water-gas generator have been tried to permit the direct gasification of low-cost bituminous coal instead of high- cost coke and anthracite for the production of water gas. Although varying degrees of success have been achieved and the water gas produced generally has been higher in calorific value, in only a few isolated in- stances has there been any sustained use of bituminous coal for water-gas production for public utility uses after the shortages of anthracite and coke have been lessened.

Jan 1, 1946

This paper summarises the influence of slurry rheology on the grinding throughput of batch laboratory and continuous plant-scale mills operating in open and closed circuit configurations. The results of controlled changes in percent solids, particle size, slurry temperature, and viscosity control chemicals are demonstrated. An underlying rheological explanation of the above factors is offered which involves tying the specific rates of breakage that are occurring in the mill with the specific rheological character that the slurry is exhibiting at any given set of operating conditions. Some industrial scale operating guidelines are presented which have proven useful in increasing the net pro- duction capability of grinding circuits.

Jan 1, 1978

By Alan Bugden

Goedehoop colliery in South Africa has experienced a number of substantial roof falls in roadways and intersections. Many of these have been associated with geological slips and/or horizontal compressive stresses. This paper describes a numerical modelling study conducted after one such fall with the objective of clarifying the roof failure mechanism associated with these falls. The fall was located at an intersection and occurred as the last cut was being made to complete the intersection. One bounding surface of the fall was formed by the geological slip; the others were formed by fresh failure surfaces. The fall took place despite the slip being identified as a hazard and additional bolts being placed by the workforce. In conjunction with the modelling work tests were conducted on samples from the roof in which the fall occurred, these gave a U.C.S. of 80 -100MPa. Several in-situ stress tests had already been conducted at the mine; a further test was conducted close to the fall site. The tests show that the largest stresses are horizontal. However, the maximum stresses of 6-12MPa are small compared to the compressive strength of the root. Computer modelling highlighted a mechanism arising from the conjunction of a geological slip and horizontal compressive stresses that could result in tensile failure of the roof leading to the fall. Sensitivity studies were conducted to identify risk factors associated with this mechanism and the modelling results used to assist in formulating a support strategy to combat falls of this nature.

Jan 1, 2003

Since production curtailment for other than engineering reasons is gradually disappearing, and more and more wells are now producing at capacity and showing declining production rates, it was considered timely to present a brief review of the development of decline-curve analysis during the past three or four decades. Several of the commoner types of decline curves were discussed in detail and the mathematical relationships between production rate, time, cumulative production and decline percentage for each case were studied. The well-known loss-ratio method was found to be an extremely valuable tool for statistical analysis and extrapolation of various types of curves. A tentative classification of decline curves, based on their loss ratios, was suggested. Some new graphical methods were introduced to facilitate estimation of the future life and the future production of producing properties where curves are plotted on semilogarithmic paper. To facilitate graphical extrapolation of hyperbolic-type decline curves, a series of decline charts was proposed, which will make straight-line extrapolation of both rate-time and rate-cumulative curves possible. Introduction During the period of severe production curtailment, which is now behind us, production-decline curves lost most of their usefulness and popularity in prorated areas because the production rates of all wells, except those in the stripper class, were constant or almost constant. While production-decline curves were thus losing in importance for estimating reserves, an increasing reservoir consciousness and a better understanding of reservoir performance developed among petroleum engineers. This fact, together with intelligent interpretation and use of electric logs, core-analysis data, bottom-hole pressure behavior and physical characteristics of reservoir fluids, eliminated a considerable part of the guesswork in previous volumetric methods and put reserve estimates, based on this method, on a sound scientific basis' At the same time, a number of ingenious substitutes were developed for the regular production-decline curve, which made it possible to obtain an independent check on volumetric estimates in appraisal work, even though the production rates were constant. with the now steadily increasing demand for oil to supply the huge requirements of this global war, proration for reasons of than prevention of underground waste is gradually disappearing. More and more wells are, or will be, producing at capacity or at their optimum rates, as determined by sound engineering practice. With this trend, the character of producing wells seems to regain, more or less, its "individuality," and the old and familiar decline curve appears to have had a comeback as a valuable tool in the hands of the petroleum engineer. It may be timely, therefore, to retrace the development of decline-curve analysis in the past by presenting a brief chronological review of bulletins and papers published during the past three or four decades, which have

Jan 1, 1945

Recent mineral exploration successes in the Proterozoic rocks of the Mount Isa Inlier are unprecedented in the regionÆs history. This new era of discovery, particularly for æblindÆ deposits, owes its origin to perseverance and advances in geoscience and exploration techniques, notably geophysics. Prospective host rocks outcrop over more than 50 000 km2 of the Mount Isa Inlier and extend a further 100 000 km2 below cover. They contain major deposits of copper, lead, zinc, silver and phosphate (Georgina Basin) and significant deposits of gold, uranium and cobalt. The discovery in 1923 of silver, lead and zinc at Mount Isa established the regionÆs world-class mineral potential. Since 1990, major orebodies have been discovered at Cannington (silver-lead-zinc), Century (zinclead-silver), Ernest Henry and Osborne (copper-gold) and extensions to known deposits at Dugald River and George Fisher (zinc-lead-silver), and Esperanza (copper). This success is of global significance and reflects a prospectivity upgrade since widespread copper mineralisation was discovered and mined in the Cloncurry district a century ago.

Jan 1, 1998

By E. A. Gulbransen, J. W. Hickman

In a previous paper' the authors have investigated the structure of the oxide films formed on most of the metals that make up the alloys of this study. The metals were studied in order to provide basic information on the structures, both physical and chemical, of the oxide films and to determine how these structures are effected by the temperature, time of oxidation, and surface preparation. It was felt that an understanding of the physical and chemical structure as well as the stability of the oxide film might furnish clues as to the nature of the reaction process and the protective quality of the film. The oxidation of the metals was studied over the temperature range 300' to 7o0°C. except for copper, wherc the range selected was 100' to 500°C. The results of these studies were presented in graphical form as existence diagrams of the oxides on a time-temperature scale. For some of the metals the existence diagrams were simple and showed few chemical transitions, but there were numerous cases where the physical state of the oxide surface was a function of time and temperature. In general the physical state of the oxide surface changed with increasing temperature so as to increase the sharpness of the diffraction patterns and to cause orientation effects to be more pronounced. Deviatiois in lattice Darameters from X-ray values were noted. In general these deviations were of positive nature and may be due to solid solution of the metal in the oxide lattice. This effect might be expected in thin oxide films. In a study of the oxidation of alloys containing two or more metals, there may arise the complicating factor of identification of the oxides formed. A thorough understanding of the oxides formed on the pure metals, therefore, was, essential before investigation of the oxidation of alloys. In this paper it is our purpose to present a study of the following problems: 1. The existence diagrams of various alloys. 2. The effect of the structure of the alloying metal on the existence diagram of iron. 3. The effect of the percentage of chromium on the oxides formed on Fe-Cr alloys. 4. The relationships, if any, between the oxides formed and the protective quality of the oxides. The following alloys are included in this study: alloys of iron with body-centered cubic, face-centered cubic and other metals, 13 Cr-Fe, 18-8 stainless steel, K4²B, Nichrome V, Hipernik, Inconel, Stellite "²I," Refractaloy, Kovar, mild steel, a series of Cr-Fe alloys and a series of Co-Fe alloys. Since many of the commercial alloys in this list contain more than two metals, various complicating factors in the identification of the oxides formed may arise.

Jan 1, 1947

By Don McColman

"Tires, although not always the largest single cost item in open-pit mining operations, will place in the top three, along with explosives and fuel. How this high-cost supply is controlled is dependent upon on an efficient tire program. The success of this program is, in turn, dependent upon the people who are directly associated with tires and their use, namely: the mine's tire personnel, the tire sales representatives and a technician for the rubber company. The technician will relay his observations and information received from the mine personnel back to the manufacturer with recommendations to overcome current problems .Haulage truck tire life and costs in a hard rock open-pit mine are governed and controlled by four important factors:I) Field control.2) Operating within manufacturer's guidelines.3) Different tire purchasing methods.4) Scrap piles.Field ControlPerhaps the most influential people involved in this program are those who live with the tire through every hour of its lifespan: the truck driver, the shovel operator, the dozer operator, the grader operator and the shift boss. Of these, the truck driver has the most control, in that he can drive over or around rock s as these situations arise. The loading area, the edge of the haul road and the dump account for most of the tire injuries.This is why shovel, dozer and grader operators must appreciate their influence on haulage tire life. Spillage cleanup must be ongoing and is not being done adequately if any of these operators are idle. The shift boss that drives by a rock on the road without removing it or calling for a cleanup has little recourse with the truck driver who runs over it-he has sanctioned the driver's actions by his own neglect."

Jan 1, 1986

By Gexin Sun

This paper overviews the recent research progress in predicting cutting performance using fracture mechanics principles. It is emphasised that rock fragmentation due to cutting is mainly a process of chip formation resulting from crack initiation and propagation or crack interaction for multi-tool cutting. This process can be simulated by using the well developed fracture mechanics criteria coupled to numerical methods. Fracture toughness is shown to be an important and useful parameter in quantifying cutting performance and in designing cutting tools. The paper concludes with discussions on the dynamic effects involved in rock cutting processes which should be taken into account for optimum cutting efficiency and tool design.

Jan 1, 1992

By M. Sagheer

This paper gives a report of the laboratory work investigating the fundamental flotation characteristics of chromite and its commonly associated mineral, serpentine. Floatability curves, showing floatability of chromite at different concentrations of sodium oleate and pH, were obtained by pick-up method. One of the difficulties encountered in flotation of chromite in presence of serpentine has been attributed to dissolved metal ions. The influence of metal ions, dissolved in pulp filtrate, on floatability of pure chromite and serpentine has been studied and it has been shown that Mg, Ca and Fe ions depress chromite. A considerable amount of work applying bubble pick-up method was carried out to counteract the depressing action of metal ions. Various methods and reagents were applied in this connection. Validity of each method and reagent has been discussed. Probably due to the abundance of high-grade chrome ores, very little has been published concerning the flotation of chromite. As improvements in mineral beneficiation are realized, more attention is being directed to low-grade ores previously considered unusable. Currently, gravity concentration is the principal process applied to upgrade chrome ores, but this cannot be used for finely disseminated ore because of the substantial losses in the fines,1,2,3 To avoid these losses, flotation can be applied to material which is too fine for satisfactory gravity concent ration, and it is probable that a combination

Jan 1, 1967

By S. K. Sharma

The present study attempts to critically review the pillar-design as required by Coal Mines Regulations of India vis-a-vis latest rockmechanics formulae, Equivalent material modelling was the approach adopted for testing the safety and stability of the pillar sizes predicted by various formulae. Two parameters, considered here for calculating pillar sizes was the stresses acting over the pillars and the strength of the pillars. Stresses acting on the pillars were calculated by the tributary area method. Based on the studies of Coates and Hustrulid, the stress obtained was reduced by 40 percent. For calculating the strength of the pillars, three formulae, namely Holland and Gaddy, Salamon and Munro and Central Mining Research Station, India, were used. The pillar widths were then determined by equating the product of recommended factor of safety and pillar stress with the pillar strength.

Jan 1, 1992

By K. M. Deen, E. Asselin

Hydrometallurgical processes, i.e., Cu extraction from a mineral concentrate and Zn electrowinning, are coupled in a battery-like system. A naturally-sourced CuFeS2 concentrate mixed with activated carbon is used as a positive slurry electrode separated by a membrane from the negative compartment. The Zn is deposited on the negative Al current collector from the circulating solution containing 100 g L–1 Zn2+ in 0.2 M H2SO4. In this battery-like system, both CuFeS2 oxidation and Zn deposition are possible during the charging cycle. The additional benefit of this setup is the energy storage if discharged by re-dissolving the Zn in the negative compartment. Cyclic charge/discharge testing revealed oxidation of the mineral concentrate supported by the Zn2+/Zn redox reaction. The coulombic and energy efficiencies increased monotonically to 95.6% and 43%, respectively, with approximately 7% Cu extraction during the first 10 charge/discharge cycles (completed in 2.4 hours). The discharge energy density also increased from 2.7 to 36.2 mWh L–1. In the following 90 cycles, the low energy (~14%) and coulombic (~33%) efficiencies that were obtained confirmed the progress of irreversible reactions e.g. Cu extraction from the mineral concentrate. Overall, approximately 16% Cu was extracted from the mineral concentrate over 100 charge/discharge cycles (or about 12.2 hours). INTRODUCTION Chalcopyrite (CuFeS2) is the main economic copper-bearing mineral, which is generally processed through pyro-metallurgical methods to produce Cu. However, environmental challenges with smelting, depletion of high-grade ores and a large number of impurities (some toxic) have resulted in continued research aimed at the development of hydrometallurgical technologies to process CuFeS2. There are a number of different proposed hydrometallurgical routes in the literature to treat CuFeS2 concentrates, but only a few have attained commercial acceptance (Dreisinger, 2006). Zn is another commercially important metal that is mainly produced via acid leaching of roasted sphalerite (ZnS). The pregnant leach solution is rigorously purified to remove all the soluble metal impurities, particularly those that are electrochemically more noble than Zn and present large kinetic activity towards H2 evolution (Hu & Piron, 1992; Mackinnon, Brannen, & Fenn, 1987; Mureşan, Maurin, Oniciu, & Gaga, 1996). Metal impurities such as Cu, Co, Ni, Cd, Pb, Sb, As, Ge and Fe etc., if they exist in the leach liquor beyond the tolerance limits, can decrease the current efficiency during electrowinning and deteriorate the deposit quality (Alfantazi & Dreisinger, 2001). A complete flow sheet, describing the process steps of Zn metal production from mine site to pure metal is presented elsewhere (Brown, Meisenhelder, & Yao, 1983).

Jan 1, 2019

By James S. Graham

Marine design and construction methods are presented on the caisson foundations for the tower piers at the Brooklyn, Ben Franklin, Delaware Memorial 1st, Tappan Zee, Walt Whitman, Throgs Neck, Verrazano Narrows, Delaware Memorial 2nd, and Newport Bridges. All of the bridges are founded on caissons, bearing on bedrock, soil, or piling. Caissons at the Tappan Zee Bridge are partially supported by piling and partially by buoyant forces. General subsurface conditions for each are provided. The purpose of this paper is inform engineers how bridge foundations using caissons were built over major waterways in the Northeastern USA in the past, anticipating a surge of new bridge construction in the near future.

Jan 1, 2013

My "outside exploration" began in November 1908, only 16 months after I had come to Bisbee as a raw engineer. The well publicized reputations of eminent engineers up to that time, including John Hayes Hammond, Herbert Hoover, James Douglas, D.C. Jack- ling, J. Park Channing, and a few others had been due to new mines they had found or brought to successful operation. And here was I, a mere youngster, given a chance to join the group. I knew there would be disappointments but I had no idea how many of them. In spite of the many prospects that turned out to be worthless I never looked at a new one without the feeling that this one might turn out to be the big success. This confidence, blind as it was, gave every arduous examination a zest and it made me climb every mountain on which the owner said there was something worth seeing, or on which T could see a distant staining that might mean ore. If I looked at every showing the owner suggested he at least would think I was honest and would bring other properties to our attention. This reputation of never refusing to go to see an outcrop, no matter how hot the desert sun or how rough the terrain, was probably one of my best assets. High as my hopes were at the start, they proved not to be exaggerated and if I were given a chance to do it again I would not hesitate, in spite of the jaundice, rheumatic fever, and other maladies that beset some of the expeditions. On the whole the results have equaled all my hopes. Toward the end of my years of active exploration I totaled up the score. Out of the prospects submitted to us about two out of three were eliminated after questioning the owner or prospector, without an examination. This left about a 1000 mines or prospects that seemed worth at least a preliminary look. One out of seven of these was worth a little development and a seventh of this seventh turned out to be a modest success or better. And nine or ten in all, or one out of 1000

Jan 1, 1976

By J. O. Marsden

The copper industry is cyclical with the price determined by market forces (i.e. the balance between supply and demand for the metal.) The period of each cycle typically varies between 6 to 9 years. These cycles drive decision making for exploration, new project and mine development, mine closures, process improvement, research and development, and technological innovation. The gold industry is fundamentally different from copper in that supply and demand do not, alone, determine metal price and many other factors play a key role, including global and regional financial conditions, political stability, and the global future economic outlook. However, the gold price experiences trends and longer term cycles that similarly drive business decision making. This paper examines developments in the copper industry that have occurred over the past few price cycles (approximately 20 years) and explores how the lessons learned can be applied to gold extraction. A number of specific examples and opportunities are discussed in detail, including; technology development and innovation, cost control and business improvement, material characterization, comminution equipment, biological heap leaching, and concentrate pressure leaching.

Jan 1, 2009