Search Documents

By E. Chiyangwa, L. Schoeman

The commercially successful electrowinning and refining of metals typically requires the optimization of the electrolyte composition and operating parameters to produce high quality compact electroplated metal. The prediction of the effect of the electrolyte composition on the structure and morphology of the plated metal remains a challenge. Initial work on the use of polarization measurements to predict and control plating behaviour in electrowinning plants involved potentiodynamic polarization but proved unsatisfactory as accurate and repeatable predictions could not be achieved. The aim of the present work was to develop a reliable galvanodynamic technique specifically applicable to the plating of zinc from sulfate electrolytes with which plant operation may be controlled and optimized. Initial results indicated that plating and nucleation potentials could be measured accurately and repeatably and that the relationship between the two could be used as a predictive tool for the effect of electrolyte composition on the quality of zinc electrodeposits.

Jan 1, 2014

By L. Maday, V. J. Perrone, M. B. Gilbert

INTRODUCTION The Brightwater conveyance system project in King County, Washington consists of constructing about 21 km (13 mile) of effluent and combined influent and effluent tunnels. The influent tunnels will collect sanitary sewerage from the service area and convey it to the new wastewater treatment plant (WTP) site at Route 9 in Woodinville, Snohomish County, Washington. The effluent tunnels will convey treated effluent from the WTP to an outfall at Puget Sound. The tunnels will be constructed primarily under residential areas, busy suburban roads and state highways. This 21 Km (13-mile) soft ground tunneling project faced many design challenges because of the geologic and hydrostatic conditions, long tunnel reaches, and large overburden depths. Boring depths typically varied from 45.7 M (150 ft) to 114 M(375 ft) with a maximum depth of 185.6 M (566 ft) deep. Conventional empirical methods for non-mountain terrain based on a 1:1 ratio of drilled footage per foot of tunnel bore (National Research Council, 1984) for evenly spaced borings provided a good start for the Phase 1 explorations. However a continuation of this approach with closer spacing was deemed inadequate by the geotechnical team for efficiently allocating geotechnical exploration resources for the final design. This paper presents a rational approach that was used to evaluate the value of a particular geotechnical exploration boring, pump test or other in-situ test. The method of analysis, which was initially developed for rock tunnels (Einstein et al., 1978), was modified for the Brightwater project. The method considers the potential construction cost risks resulting from variable geologic conditions, the cost and reliability of the geotechnical exploration and the earned value (cost risk reduction) of performing the geotechnical exploration. PROJECT DESCRIPTION In total the land portion of the conveyance system will include approximately21 Km (13 miles) of tunnels ranging in size from 3.0 to 5.2 M (10 to 17 ft) minimum inside diameter with overburden depths of 30.0 to 168 M (100 to 550 ft) and

Jan 1, 2005

By A. Wang

This paper defines the elements of a basic economic model for decision-making when considering a methane drainage system for an underground coal mine. A drainage system will require significant capital and operating expenses; hence the decision to utilize drainage must be made carefully. The model outlines the basic structure of decision-making and considers the costs and benefits when the methane is marketed and when the methane is vented to the atmosphere. The effects on mine safety and the dust levels in the mine are also considered, both in a general format and as economic variables. Sources of information for executing this decision-making are provided for an actual mine decision.

Jan 1, 1997

By C. N. Savage

An industrial minerals review involves an attempt to assemble field and statistical data which are obscure, elusive and incomplete. Often, when me statistical data are available, combining or lumping of commodity values conceals the value of specific items. Personal knowledge of the minerals known to occur in the area of concern, combined with whatever available published data may be compiled, together with careful use of several extrapolation methods, may yield an acceptable summary review of the industry. However, it is particularly hazardous to speculate on future trends and economic aspects because of the many unpredictable variables which may affect the industrial minerals business. Among these variables are the effects of diverse geological conditions, the impact of technological changes (including new uses for minerals not formerly considered industrial types), changing socio-economic factors (including growing environmental controversy), use of substitutes and even recycling of some of the industrial minerals (for example, building materials, lime, etc.). My main objectives are to reveal, as accurately as I can, the state of the in¬dustrial minerals situation, and the effects of possible future developments on this industry in Idaho. Where the words...industrial-tyke minerals, .are used in this discussion, reference is made to selected metallic and nonmetallic minerals and related materials, as well as rock (Table I). Industrial minerals known to be present in Idaho may be listed under general use categories as in Table 1. Some of these commodities are being marketed, have been marketed in the past, or occur in potentially marketable quantities. Mineral fuels are neither mentioned, nor are they considered important in Idaho. Based upon our present knowledge and lack of known, economically valuable occurrences of these commodities, they are considered insignificant (Idaho Bur. Mines and Geology, 1964). Information used for this study is from several sources. Most of the statisti¬cal information should be credited to the U.S. Bureau of Mines Minerals Yearbooks,

Jan 1, 1971

By John S. Alexander

By Elmer Palmer

As part of the Goldcorp Inc growth plan Minera Peñasquito SA de CV has developed its polymetallic deposit with a large ?state of the art? concentrator to process lead and zinc ores. The plant consists of two grinding lines including 38ft diameter SAG mills and 24ft diameter ball mills. During mid to late 2009 concentrator commissioning activities commenced. First concentrates were produced in October 2009 and now the plant is meeting its design basis of 65,000 mtpd per line. This paper describes the design and operational experience to date for its grinding circuit design, together with the recently commissioned HPGR crushing circuit.

Jan 1, 2012

By Aaron Archer, James Parkes

This paper presents design considerations for the major underground elements of the pending BCRUA Phase 2 Raw Water Delivery System Project. These elements include two Lake Taps; an 8,800 LF, minimum 10-ft OD intake tunnel; a suction chamber with 6 Pump Shafts; a 30-ft diameter, 300-ft deep Main Shaft; a 2,600 LF Transmission Tunnel with 78-inch steel liner; and a 130-ft deep shaft on the Transmission Tunnel. The tunnels and shafts will be excavated through the Glen Rose limestone. The design development included consideration for technical requirements, easements, third party commitments, previous local project experience, and constructability based on contractor outreach.

Jun 13, 2021

By Lucia Kuizon

The Morongo Wilderness Study Area (WSA) is in south central San Bernardino County, California. U.S. Bureau of Mines examined the area during the fall of 1983. No mines, prospects, leases, or mining claims were found in the WSA. There are no known mineral deposits within the study area boundaries. Sand and gravel in the area is suitable for many types of construction uses, but similar and larger deposits outside the WSA are closer to markets. No energy resources have been identified in the WSA.

Jan 1, 1984

By Alexandra P. Wright

A vital aspect of environmental impact assessment for surface mining operations is the determination of potential effects on water resources. This topic has been the subject of much recent concern, controversy and legislation. As increasing data become available regarding the types of hydrologic effects that may be anticipated, methods for safe guarding our water resources can be refined. In view of our current energy situation, the need to develop coal re- sources in a timely and economic manner is apparent. The challenge to the mining industry is to develop these resources in a manner that is also compatible with the beneficial use of water resources in mining regions. For this reason, thorough evaluation of the hydrology of potential mining areas in consideration of proposed mining processes and relevant legal criteria is essential. While pre-mining hydrologic investigations often suggest generalized potential effects, a more reliable method for evaluating specific potential effects is to establish and maintain a hydrologic monitoring program. Such a program must be carefully designed to suit the specific project and its location. This paper describes an approach for selection of criteria for designing a monitoring program for a proposed coal surface mining operation and gasification plant in southwest North Dakota. Woodward-Clyde Consultants (WCC), recently prepared an environ- mental impact report for the ANG Coal Gasification Company (ANG), a subsidiary of the American Natural Gas Company. The mining will be carried out by The North American Coal Corporation (NACCO). Preparation of the report provided the opportunity for the development of a sensitive and economical monitoring program which would function as a baseline hydrological data gathering network as well as act an an early detection system for hydrologic effects of the proposed mining.

Jan 1, 1975

By T. Xu

"The CTL-500 centrifugal extraction machine, which was independently developed by Baotou Shibo Rare Earth Extraction & Equipment Co., Ltd., is presented in this article. The machine is based on centrifugal extraction principle and has been used in P507-HCl-RECl3 extraction system. Automatic control has been utilized in the system. In this paper, a comparison is made between centrifugal extraction and conventional mixer-settler extraction and satisfactory results are shown. INTRODUCTIONCentrifugal extraction is a fast and efficient liquid-liquid extraction method. The process includes solute transfer and separation of the two liquid phases. In the CTL-500 machine, the organic and aqueous phases individually enter a lower mixing chamber in certain proportions and are mixed and dispersed and solute thereby transferred from one phase to the other. The mixed phases pass into a rotating drum and the two liquid phases are separated under centrifugal force. As it flows upward, the aqueous phase, which has a higher specific gravity, flows away from the rotating drum centre towards the drum wall and the organic phase flows towards the drum center. The two liquid phases enter into collection chambers through independent weir plates and are discharged from the machine.The centrifugal extraction machine has been widely used in liquid-liquid separation, either without solid or with small quantities of solids (Chen, Zhang, Zhuo, Chen & Li, 2008; Duan, Jing, Zhu & Chen, 2007; Duan, Zhou & Zhou, 2006). Examples of the use of the centrifugal contactor include the separation of water from crude oil, treatment of heavy oil and diesel to eliminate water and salt; the extraction of penicillin, garlic oil, malathion, and interferon; the hydrometallurgy recovery of nickel, copper and uranium; extraction of edible oil, spice, refined oil and food color; treatment and recycle of print and dyeing wastes; treatment of hydroxybenzene-contaminated sewage by multistage extraction and separation of water from oil in ship sewage."

Jan 1, 2012

By BHAMIDIPATI S. SASTRY, Pavan Kumar Kattamuri, ADITYA PANDEY

The thermal conductivity of rock surrounding the airway is one of the most important thermal properties for estimating strata heat transfer into the mine air and for designing the air-cooling strategies. Several laboratory methods are available for the determination of thermal conductivity; however, most of them are complex and cumbersome. The present study explains the working principle of Lee’s apparatus which is relatively simple, easy to fabricate and use, and provides consistent results. In the present study, thermal conductivities of sandstone cores obtained from an Indian coal mine are determined using Lee’s apparatus. An approach is discussed for determining the temperature gradient of sandstone specimens while cooling and used for calculating thermal conductivity. The thermal conductivity of different sandstone specimens attains values between 2.37 and 2.59 W m− 1 °C−1. For different sandstone cores obtained from the field, properties including specific gravity, specific heat capacity, thermal diffusivity, and porosity, along with thermal conductivity, are determined and highlighted in this study.

Jul 20, 2021

By C. Keefe, O&apos

Measurements of the quantity of entrained air within processes have challenged instrumentation developers for years. This is particularly true in the unique and demanding operating environment and applications seen in minerals processing. In minerals processing applications, entrained air plays a role in errors seen within nuclear density gauge measurements and in pumping efficiency. It is also the major component of flotation processes. The measurement of the quantity of entrained air, known as the gas void fraction, can now be performed from the outside of a process pipe through CiDRA?s patented passive sonar array-based technology. Within column cells, the need for a robust, no maintenance, accurate means of measuring the entrained air, known as gas holdup, has resulted in a submersible version of this technology. CiDRA?s meter technology calculates the gas void fraction by first measuring the speed at which naturally occurring sound in the process slurry propagates past an axial array of sensors. These sensors are incorporated in a band that is wrapped around the outside of the pipe, resulting in no process downtimes for installation and unprecedented reliability. A known relationship between this speed of sound and the entrained air captured in the form of bubbles within the slurry is then applied in CiDRA?s meter to calculate the gas void fraction. This paper will present the measurement technology, its operation, its calibration and its application in a variety of gas void fraction and gas holdup measurement situations such as pumping efficiencies, hydrocyclone operation, external sparging, and column cells.

Jan 1, 2008

By M. Bouchard, B. Cadieux et F. Goutier

Five phases of ice movement were r es pons ible f or glacial dispersion in t he study area. I ce fl ow directi on changed prog r es s ively from SE to SSW and then to the S. All observed glacial sed iments are associated with a south-southwest to south movement; t hey are grouped, on the basis of their texture, structure, morphology and composition, into four distinct lithofacies. A lithological study of the coarse-grained fraction (4-128 mm) of these lithofacies shows systematic compositional differences. These are: 1) variations in the proportions of local bed rock fragments; 2) variations in the horizontal displacement of the maximum abundance peak of a given lithology relative to its source area, and 3) variations in the length of dispersion trains associated with each lithofacies. Although dispersal trains can obviously be mapped without differentiating li thofacies, studies based on the consideration of lithofacies should give more reliable results than conventional methods.

Jan 1, 1984

By Thomas Pea, Heiner Kontrus, Jérôme Steinkühler

In tunnel condition assessment, the trend is towards comprehensive 3D measurement combined with high quality image texture to document and quantify damages to the tunnel surface and to create a cohesive data base of the structural conditions throughout its lifespan. The faster such measurements can be made on site, the less it impacts traffic conditions of the highly sophisticated subway systems. The Dibit high-speed 3D scanning system which is based on Photogrammetry and LiDAR technology enables data acquisition in tunnels at a speed of up to 60 mph. Given the high rate of speed the system can operate, tunnel shutdowns can be drastically reduced, and tunnel safety increased. The photorealistic texturing of the 3D-model allows the identification and analysis of smallest material damage (e.g., cracks ≥0.3 mm wide). The publication illustrates technical details and 3D results of the innovative system from measurements that were performed in the subway tunnels of the Bay Area Rapid Transit System in San Francisco, CA (total length 66.23 km).

Jun 13, 2021

By Immo H. Redeker

Introduction In October of 1961 Texas Gulf Sulphur Company contacted the Asheville Minerals Research Laboratory, of the North Carolina State University, and requested assistance in the development of a phosphate ore body in Beaufort County. The main: objectives of the work at Asheville were defined as follows. The Laboratory should try to determine on the basis of drill core samples, submitted by Texas Gulf Sulphur Company, the highest grade of phosphate concentrate that could be obtained with high recoveries from North Carolina ore, the thickness of the ore body that could be treated economically in one section, and the quantity of concentrate that could be obtained per acre. The results should be compared with data obtained from the treatment of Florida ores. It was important to use mineral preparation methods during the initial laboratory work that could be verified later by continuous pilot plant operation and could be scaled-up for a commercial plant. The writer was in charge of the project at the Asheville Minerals Research Laboratory and participated in the development of one of North Carolina's greatest mineral resources from the first drill core examination to the production of the first poundage and tonnage quantities of flotation concentrates. The Lee Creek phosphate mine and mill was put in operation in early 1966 and can produce three million tons of phosphate concentrate a year. Sulfuric- acid, and phosphoric acid plant, diamonium phosphate plant and triple super phosphate plants came on stream in 1967; at that time they were the world's largest. Now that a phosphate industry has been established in the State, it]

Jan 1, 1971

By C. P. Manning

This paper reports recent progress in the development of a unique metal extraction technology utilizing zirconia-based inert anodes for the electrolytic reduction of metals from their oxides. In this process, the target metal oxide is dissolved in an ionically conducting liquid solvent phase. An extended anode consisting of an oxygen-ion-conducting stabilized zirconia membrane in intimate contact with a catalytically active electronic phase and an inert electronically conducting cathode are inserted into the molten flux containing the oxide. When the appropriate electric potential is applied between the electrodes the target metal is reduced at the cathode and oxygen ions are selectively transported across the stabilized zirconia membrane and oxidized at the anode. When the process is conducted at temperatures between 1200-1400°C, the ohmic resistance drop across the stabilized zirconia membrane is low, and high current densities on the order of I A/cm2 or greater can be obtained. In addition, the process efficiency can be increased further by directly reforming hydrocarbon fuel over the anode. Laboratory experiments at Boston University have demonstrated the technical viability of employing zirconia-based inert anodes for environmentally sound production of metals such as magnesium, tantalum, aluminum, etc., directly from their oxides. Significant progress has been made in the application of this concept to the electrolytic reduction of magnesium at 1300°C. The research topics covered include stability of the zirconia membrane in the selected molten solvent (flux), volatility of the flux, electrochemical characterization of the electrolytic cell, and analysis of the metals produced.

Jan 1, 2003

By S. McPherson, M. Chalkley, R. Ellenwood, W. Nicot

"The Moa JV was formed in December 1994 as a 50/50 joint venture between Sherritt Inc. and General Nickel Company S.A. of Cuba. The joint venture consists of the mine and Pedro Sotto Alba processing plant in Moa, Cuba and the Corefco refinery in Fort Saskatchewan, Alberta, Canada. Throughout its now nearly 23-year history, the Moa Joint Venture has faced a number of global, operational and process challenges. Global challenges have included high input costs such as for fuel oil and sulphur, as well as low nickel prices. Operational and process challenges have included increasing ore haulage distances, decreasing ore Ni + Co grades, and increasing ore impurity contents. For example, increases in impurities such as Mg and SiO2 in the ore result in increasing acid demand in leaching and decreasing solids content of preheated leach feed slurry, respectively. In spite of these challenges, the mixed sulphide production capacity from the Moa Joint Venture has increased from 12,500 to 37,000 t/y Ni + Co since 1994 by judiciously targeting expansion projects and by continuously performing process and operational improvements.INTRODUCTION The Pedro Sotto Alba high pressure acid leach (HPAL) plant at Moa Bay, Cuba has a long history (Maslenitzkiy, 1969; Chalkley, 1996; Carlson, 1960; Roy, 1961; Carlson 1961). The plant was constructed by Moa Bay Mining Company and started up in late 1959 after several years of process development by Freeport Nickel Company, including operation of a 10 t/d plant in Hoskins Mound, Texas and a 50 t/d plant in Port Nickel, Louisiana (Southwick, 2004), as well as development work by Chemical Construction Company (Chemico) to precipitate metal sulphides (Roy, 1955a; Roy, 1955b). The Moa plant had an original reserve of 50,000,000 t of ore, graded at 1.35 wt% Ni, 0.146 wt% Co, 3.70 wt% Si, 1.00 wt% Mg and 4.5 wt% Al. At original design rates of 2,000 kt/y of ore, the design capacity of the plant was around 25,000 t/y Ni + Co as a mixed sulphide product, which would be shipped to the Port Nickel Refinery in Louisiana for processing. In 1960, the plant changed ownership and was restarted in 1961 under Cuban management. Between 1961 and 1989, the plant was also supported by involvement from the former USSR, supplying spare parts and consumables. In 1994, Sherritt Inc. partnered with the General Nickel Co. S.A. of Cuba and formed the Moa Joint Venture. This joint venture includes the mine and Pedro Sotto Alba HPAL processing plant in Cuba and the Corefco refinery in Fort Saskatchewan, Alberta, Canada. Under this partnership, ore is processed in Cuba to produce a nominally 55 wt% Ni and 5 wt% Co mixed sulphide product that is shipped to Canada and processed by Corefco to produce class 1 nickel, high grade cobalt and byproduct ammonium sulphate fertilizer."

Jan 1, 2017

By Robert McClure, Carlton Lehman

Rendering safe explosives in an urban environment presents a unique challenge due to the safety concerns and disruption to the general public. Potential damage to the surrounding homes, businesses, utilities and transportation infrastructure are some of the major concerns when planning the render-safe operation. Engineering controls to mitigate blast effects, such as damaging air over pressure levels, material ejection and ground borne vibration, need to be implemented as part of the operation. Monitoring of seismic and air overpressure during these operations are needed to protect against potential claims when controlled or unplanned detonations occur.

Feb 1, 2020

By F. G. Schwartz

The Bureau of Mines developed a rapid and precise method for predicting storage stability of motor gasolines. This method resulted from the investigation of many analytical techniques as well as a study of fuel composition and fuel component gum-forming mechanisms. The first section of this bulletin discusses the development of the prediction test through its several phases, including revision of the standard 110° F storage test; attempts to develop a modification of the ASTM D525 induction bomb test; and the ultimate abandonment of this procedure with the adoption of the 16-hour oven test that was both precise and rapid. The second section comprises a discussion of further studies of fuel com- position, including the reactivity of certain sulfur compounds and hydrocarbons to form gum. The compositions of various gums and inorganic deposits are reported in terms of elemental analysis and spectroscopic examinations. The reactions of tetraethyllead with selected hydrocarbons are also reported.

Jan 1, 1972

Vertical flow systems (SAPS, vertical flow wetlands) are increasingly used for passive treatment of mine drainage that is net acid. Data on 30 systems in eastern US show that well designed systems typically add about 40 g/d/m2 of alkalinity to influent net acid water. If they are designed with a conservative loading rate of 25 g/d/m2 and carefully constructed, they produce net alkaline water. Alkalinity added depends on influent acidity, Fe, pH, and retention time, and ranges widely, from 7 to 484 mg/L, so this is not a useful design criterion. Some waters may benefit from retention times longer than the conventional 12 - 16 hours, but the design must be partly based on cost-benefit considerations. Systems with fine limestone added to the compost layer perform better than average, perhaps to an alkalinity generation rate of 80 g/m2/d. A variety of problems are noted in the 30 systems and others reported in the literature. Systems with high influent Fe (> ~75 mg/L, varying with pH) tend to gradually decrease in flow rate because of precipitation and settling of Fe hydroxides on top of the compost layer. Some high-Fe systems precipitate Fe in the limestone layer, suggesting inadequate compost thickness, or short-circuiting through thin spots. Systems with Al exceeding about 10 mg/L tend to plug because of Al hydroxide precipitation in the limestone layer. Flushing only removes a small part of this precipitate, but can extend life. Some systems are ineffective because of failure of the inflow system. Some systems are uneconomic because they are oversized. A continuing program of inspection and maintenance is necessary for long-term performance.

Jan 1, 2003