Search Documents

By Jason Buenker, Molly Winston

Torque-installed piles are gaining popularity in Southern California as the go-to deep foundation element for small- to medium-capacity loads in urban environments. The torque-installed pile is a displacement- based screwed pipe pile with a closed-end conical tip welded to the bottom of the pipe. Torque-installed piles are most efficient in loose to medium dense soils with high liquefaction potential. Where used properly, torque-installed piles can be installed faster, require less clean-up, and create less onsite vibration/disturbance than other pile alternatives. However, torque-installed piles are not applicable in all soil conditions and care must be used to apply the pile effectively in the correct subsurface environment. This paper will review current Southern California state-of-the-practice for torque-installed pile design and construction, potential roadblocks to successful installation, and available capacities from load tests. INTRODUCTION Torque-installed piles are a type of full-displacement screwed pipe pile originally developed in Southern California circa 2001 by Substructure Support, Inc. The pile is unique for its proprietary closed-end conical tip shown in Fig. 1. The tip has a welded steel-helix plate and cutter teeth that allow the pile to be advanced efficiently under applied torque and down pressure (crowd). Since original development of the pile, several contractors or manufacturers have proposed similar proprietary screw-type piles with comparable conical tips. Pile installation is relatively quiet, vibration-free, does not generate spoils, and faster than comparable pile types. The pile was originally developed as an alternative to driven pile foundations and remains a critical substitute to driven foundations in urban environments. Torque-installed piles are conventionally specified as 12 ¾-inch outside diameter (OD) steel pipes with a ⅜-inch-thick wall, although larger sizes with alternative dimensions have been used outside Southern California. Pile installation lengths generally range from 30 to 50 feet but may reach 80 feet or greater where soil conditions permit. The pile is generally backfilled with concrete following installation to increase lateral pile stiffness and may incorporate rebar cages or other reinforcing steel to facilitate connections to structural elements. The pile is frequently specified using performance-based specifications that encourage contractor innovation and use of proprietary installation means and methods.

Jan 1, 2019

By H. E. Powell

The magnetic susceptibility, the geographical source, and associated minerals are given for 44 copper-, 26 lead-, and 19 zinc-bearing minerals. Of the 44 copper minerals/ all had a susceptibility of less than 15 X 10-6 cgs, and about 20 percent of them were diamagnetic. Of the 26 lead minerals, all had a susceptibility of less than 11 X 10-5 cgs, and almost half of them were diamagnetic. And, of the 19 zinc minerals, all except four had a susceptibility of less than 9 X 10-6 cgs, and about one-fourth of them were diamagnetic.

Jan 1, 1968

The Atlanta Mine is located in east central Nevada, in Lincoln County, 116 km (72 miles) south of Ely and 80 km (50 miles) northeast of the old mining town of Pioche. From this famous district, high-grade copper ore was mined and shipped to a smelter in Wales in the 1850s; an early day lead blast furnace was also in operation. The Standard Slag Company began operations in May 1975 on the well known Atlanta Mine, which was operated by Roy Hardy in the 1930s. The mill is currently processing 450 mtpd (500 stpd) of gold-silver bearing ore. Mining by open pit is in a brecciated zone occurring between limestone-dolomites on the foot wall and tertiary rhyolites on the hanging wall. The quartz breccia is considered among the most abrasive in the world - shovel teeth must be replaced every week. Stripping ratio is 3.9 to 1.0. Because of the hard abrasive ore, the crushing plant consists of four units: two jaw crushers in series, one Hydrocone, and one Gyradisc. Mine feed to the primary crusher is limited to 610 mm (24 in.) in size. The remaining crushers work in closed circuit with screens to produce a mill feed of 6 to 13 mm (0.25 and 0.50 in.). Hardness of the ore is demonstrated by the fact that the reversible liners of the primary jaw crusher had to be replaced in early 1978 after handling only 39,000 mt (44,000 st) at a cost of $0.095 per mt ($0.086 per st). Another example of the extreme abrasiveness of the breccia ore was the total cost per ton in 1977 for all wear parts in the comminution circuit, including screens and grinding media. This amounted to $2.84 per mt ($2.58 per st). The Atlanta grinding plant consists of three ball mills to grind the 7 mm (1 /4 in.) crushing plant product to 85 to 90% minus 150 microns (100 mesh). Feed rate to the primary Tricone mill is determined by maintaining a cyclone overflow at 28 to 38% solids, which controls the grind mentioned above. A mixture of 90 and 65 mm (3.5 and 2.5 in. ) balls are charged to this primary mill. Both the secondary mills are charged with 50 mm (2 in ) balls. Total ball consumption is 2 kg per mt (4 lb per st). All three ball mills use rubber liners. Primary mill cyclone underflows are fed to the secondary mills close circuited with the same cyclones.

Jan 1, 1981

By Ihsan Berk Tulu, Michael Sloan, Ted Klemetti, Michael M. Murphy, Gabriel S. Esterhuizen, Jame Sumner

"In this paper, the advantage of using numerical models with the strength reduction method (SRM) to evaluate entry stability in complex multiple-seam conditions is demonstrated. A coal mine under variable topography from the central Appalachian region is used as a case study. At this mine, unexpected roof conditions were encountered during development below previously mined panels. Stress mapping and observation of ground conditions were used to quantify the success of entry support systems in three room-andpillar panels. Numerical model analyses were initially conducted to estimate the stresses induced by the multiple-seam mining at the locations of the affected entries. The SRM was used to quantify the stability factor of the supported roof of the entries at selected locations. The SRM-calculated stability factors were compared with observations made during the site visits, and the results demonstrate that the SRM adequately identifies the unexpected roof conditions in this complex case. It is concluded that the SRM can be used to effectively evaluate the likely success of roof supports and the stability condition of entries in coal mines.INTRODUCTIONSince the introduction of roof bolts in the coal mines during the late 1940s and 1950s, roof bolts promised to dramatically reduce roof fall accidents (Mark, 2002). However, ground falls still remain a significant factor in underground coal mine injuries and fatalities. In 2013, ground falls accounted for 4 of the 14 fatalities and 166 of the 1577 reported lost-time injuries in underground coal mines (MSHA, 2015).The design of appropriate support systems requires the understanding of: 1) the variable nature of the rock mass, 2) the performance and characteristics of the roof support, 3) the interaction between the rock mass and the installed support system, and 4) the in-situ and mine-induced stress distribution around the excavation. Over the past 25 years, multiple design approaches have been used in coal mine ground control. The approaches include empirical mechanistic methods, empirical statistical analysis, rules of thumb, and numerical methods (Hebblewhite 2006). In the U.S., Analysis of Roof Bolt Systems (ARBS) can be given as an example of an empirical method. ARBS uses relatively simple equations to calculate the intensity of support provided by a roof bolt system and compares it with a suggested ARBS value (Mark et al., 2001). The suggested ARBS design equation is derived from an analysis of 100 case histories. The ARBS design equation is dependent on two parameters: depth of cover and Coal Mine Roof Rating (CMRR). More recently, a probabilistic design approach was developed by Canbulat and van der Merwe (2009) in South Africa. In this method, the variability of the rock mass, the mining geometry, and support characteristics are included in the analytical models. The major advantages of these two methods are: 1) they can be applied rapidly and easily, 2) complex rock mass/ roof support interaction mechanisms are represented with simple equations, and 3) they are supported by large databases. However, both methods generally ignore mining-induced stress distribution, details of the roof support system, details of the geological setting, and the interaction between the support system and the rock mass."

Jan 1, 2015

By E. Scheepers

Within a phosphorus producing submerged arc furnace it was found that the continuous fluctuation of the furnace between a flowrate-driven state (high throughput) and a thermodynamic-driven state (low throughput) caused both techniques to have similar overall, predictive abilities and resulted in a linear, ARX-type, adaptive prediction model as the model of choice. Secondly, this pre-diction model was developed, tested and then shown to have a reasonable, 8-hour-ahead predictive accuracy (R2, coefficient of determination) of 30% (±6%) on future Pslag values. This inherent relationship exists because, at the precise moment of a Pslag prediction, the furnace already contains the metallurgical memory (input variables to the linear model) needed to ensure that some predictive possibilities will always exists - all as a result of the long residence times in the furnace. Residence time, however, is not a directly adjustable variable but rather a fully dependent variable and a function of an array of interconnected and interactive variables. In fact, this applies to virtually all input variables, reemphasising the importance of innate metallurgical memory. Thirdly, predictive control possibilities were explored by simulating the set-points of two fully independent variables used by operators to control the process: the ratio of fixed carbon-to-P2O5 and the ratio of silica gravel-to-pellets. This linear, predictive control model showed only a slight improvement with an 8-hour-ahead predictive accuracy of 35% (±7%). This highlights how ineffective current adjustments are in optimally steering the process and how difficult even incremental improvements in feed-forward and predictive control can be. Finally, it is shown that fundamental design-, sampling- and process restrictions currently associated with the process will always limit the predictive and especially control accuracy or meaningfulness of any dynamic model. These restrictions include the size of the furnace resulting in long residence times, 8-hours sampling intervals, an extremely complex and interactive process and a 16% spatial analyses variation on the Pslag values ? the very value that the model is to predict. The point is made that, given the current status quo, even the perfect dynamic prediction model can not improve on an 8-hour-ahead prediction of 30% (±6%). This barrier can only be pierced with e.g. tidier and more frequent sampling regimes and other upfront capital investments, a decision that becomes a cost accounting exercise and that can only be taken by the management structure. An investment demanding ever-increasing attention is CFD software and it?s potential to shed more light on the complex interactions within the furnace.

Jan 1, 2014

By Jon Ike Isaacson, Michael Miller, Jarek Trela

Despite reef structures being relatively common in carbonate rocks around the world, tunneling experience in reefs is extremely rare. Impacts and risks associated with reef tunneling through these geologic features were also relatively unknown. A new reef was encountered during construction of the Lower Pogues Run Tunnel in Indianapolis, exposed over 5,000 linear feet along the alignment, resulting in adverse impacts on construction. Analysis of investigation data and construction from this encounter provide insight into the identification and characterization of reefs along tunnel alignments as well as the potential impacts on construction for future tunneling within reef structures.

Jun 23, 2024

By A. R. Mumford

During the course of an investigation conducted by the fuel section of the Bureau of Mines , on a hand- fired return- tubular boiler plant , it was found that the average cost of fuel to produce 1,000 lb. of steam was $ 0.5287 . Tests conducted after some simple changes had been made in the furnaces , and in the control of the boilers , showed the previous high cost of fuel per 1,000 lb. of steam could be reduced to the reasonable figure of $0.3540 , or the equivalent of over 30 per cent saving in fuel cost .

Mar 1, 1923

By L G. White

During 1958, prospecting parties working for the Mackenzie Syndicate in the Flat River area of the Mackenzie mountains, Northwest Territories, identified tungsten mineralization and located the property now being developed by the Canada Tungsten Mining Corporation Ltd. Scheelite mineralization, associated with pyrrhotite and minor chalcopyrite, occurs in lime silicate skarn replacement zones within a limestone-chert-argillite series intruded by granitic dykes originating from the ? main batholithic mass underlying the sedimentary beds. The results of surface outcrop sampling and 15,000 feet of grid-pattern diamond drilling have been combined to outline an orebody estimated to contain 1.32 million tons, grading 2.51 per cent WO after applying a 10 per cent dilution factor for mining purposes. T HE property of Canada Tungsten Mining Corporation Ltd. is located in the upper Flat River area of the Mackenzie mountains, Northwest Territories. Skarn-type replacement deposits containing scheelite mineralization are .situated between elevations of 4,500 and 5,500 feet above sea level along the east flank of the mountain range forming the boundary between the Yukon Territory and the Northwest Territories. The nearest supply center for the area is Watson Lake, Yukon Territory, located at Milepost 635 on the Alaska Highway.

Jan 1, 1963

By W. H. Patterson

The history and experience of early companies in the Islands is illustrated by the typical transactions of Trans-Western from 1959 to date. Trans-Western had entered into farmout agreements with companies strong enough to carry out at least the required minimum exploratory work and then such development as might be warranted. The farmee companies were required to make deposits to guarantee work performance during the first period of validity, i.e. the first 3 years of the 12-year life of the permits, and at the rate of 5 cents per acre. At that time, a good deal of geology was available, as a result of extensive exploration that had been carried on by the Geological Survey of Canada and other geological enterprises, with field parties travelling over and camping on all of those Islands. Trans-Western's farmees then selected, from Trans-Western's priority on 13.5 million acres, what they believed were the lands most prospective of producing large oil and gas discoveries, and, having the right to trim off acreage which they considered less prospective, thereby reducing the acreage of Trans-Western and its farmees to in excess of 5.5 million acres. The farmees then commenced a 3-year program carrying out geological exploration to the required minimum of 5 cents per acre, and with some permanent and many mobile camps.

Jan 1, 1969

By D. G. Leddy, J. B. Johnson, L. D. Gratz, S. T. Bagley

"Studies have been conducted at Michigan Technological University (MTU) for over twenty years on methods for characterizing and controlling particulate emissions from heavy-duty diesel engines and die resulting effects on regulated and unregulated emissions. During that time, control technologies have developed in response to more stringent EPA standards for diesel emissions. This paper is a review of: 1) modem emission control technologies, 2) emissions sampling and chemical, physical and biological characterization methods and 3) summary results from recent studies conducted al MTU on heavy-duty diesel engines with a trap and an oxidation catalytic converter (OCC) operated on three different fuels. Control technology developments discussed are particulate traps, catalysts, advances in engine design, the application of exhaust gas recirculation (EGR) and modifications of fuel formulations. Methods for dilution tunnel sampling, particle size analysis, chemical analysis with emphasis on polynuclear aromatic hydrocarbons (PAH) and nitro-PAH, and biological characterization using mutagenic activity (Ames) assays are described, along with statistical approaches to experimental design and data analysis.In studies at MTU, both particulate traps and an OCC have been shown to be effective for the reduction of total particulate mauer (TPM), with the OCC being better al reducing all forms of hydrocarbon emissions, including PAH and nitro-PAH, and with the traps being better at removing the solids (SOL). The use of low sulfur fuel (0.Ql % by mass) has led to additional reductions in TPM; the low sulfur fuel has been shown to reduce the number of small, nuclei-mode particles for one of the engines tested. PAH, nitro-PAH, and mutagenic actively levels generally decreased with use of either the traps or the OCC.INTRODUCTIONDuring the 1980s and the early 1990s there have been significant advancements in the development of technology to control diesel particulate emissions. Efforts have been focused on internal control of the engine by design, the use of after-treatment devices, and improvements in fuel formulations to reduce all the diesel emissions. The research and development activities have been driven by the need to meet the US EPA heavy-duty vehicle standards shown in Table 1. The important standards for new technology are the 1994 heavy-duty vehicle 0.1 gm/bhp-hr particulate, the new urban bus 0.05 gm/bhp-hr particulate standard for 1996 and the heavy-duty vehicle 4.0 gm/bhp-hr NOx standard for 1998."

Dec 1, 1995

By J. W. Howland

To determine their effectiveness in different climate and soil conditions, a demonstration of dozer blades specifically designed for recontouring mine spoil was conducted at an East Texas surface coal mine. The specialized equipment included a 48-foot angle blade, a modified 24-foot "U" blade, a 13-foot deep "U" blade, and a 24-foot grading bar. Both the 4b-foot and the 24-foot "U" blades were mounted in a two-tractor, single-operator configuration. To meet flotation problems common in this mining region, a 22-foot lightweight blade was developed and demonstrated for use on a 400-430 hp tractor. The demonstration involved 1,185 acres and showed a 50% reduction in reclamation costs and a 47% reduction in fuel requirements for this mine site over conventional equipment. Improved equipment, trained operators, good supervision, and improved monitoring techniques contributed to the savings. Procedures and results of the demonstration are presented and analyzed here along with guidelines for application of findings.

Jan 1, 1981

By Giovanni A. Bonita, Asher H. Peltz, Sean D. Johnson

This paper examines a complex earthwork project in the Washington DC metro area that had project delivery directly impacted by questionable instrumentation monitoring data. The case study summarizes the impacts to the project caused by questionable instrumentation data and reveals how the authors were able to utilize data to extract meaningful insights. The case study also demonstrates how clear data presentation became a key factor in maintaining stakeholder trust and facilitated progress of the project schedule. The case study highlights key points to collecting high quality instrumentation data, approaches to assess and improve value of the data collected, and techniques to reduce and interpret questionable data.

By Ron Stewart, Richard Youmaran, Andy Adler

In the current context of heightened concerns with explosives security, there is significant interest in technological controls to improve security. It is important to be able to control what is fired, by whom, where and when. This paper describes research Orica has performed to investigate and test biometric systems to address the question of "by whom". The goal of this research is to incorporate the most suitable biometric system onto the 'blaster' unit of an electronic initiation system. This approach will ensure that only authorized personnel can initiate a blast involving electronic detonators. Requirements analysis: we initially explored many different biometric technologies to evaluate them against the requirements, including security, usability, ruggedness, size, form factor, privacy, and operational temperature range, This analysis identified chip based fingerprint sensors as the best candidate. Development of prototype units: in order to test the identified sensors, we modified standard, commercially-available, electronic blast initiation units ("blaster") to incorporate a fingerprint reader. Testing and evaluation: Biometric We conducted a biometric scenario evaluation in order to determine: 1) security level (measured by false accept rate (FAR)); 2) usability (measured by failure to enroll (FTE) and false reject rates (FRR)), and to 3) discover environment specific issues and challenges (such as temperature, humidity, dirt, or those related to the usage patterns of the user group). Tests were conducted at quarry sites in eastern Ontario, Canada. Results show rates of: FAR= 0%, FTE= 1.67%, FRR= 28.81%. Overall, these results suggest that this fingerprint biometric technology has a good level of usability in this application of electronic blast initiation control.

Jan 1, 2007

By E. W. Greig

This paper is an account of exploration for bauxite in the Amazon Basin, Brazil, and particularly of the discovery, exploration and development by Alcan of the Trombetas deposit so a general account of the Trombetas Project has already been published in E/MJ (Anon. 1975) to which the reader is referred for details on owner-ship, infrastructure and construction as well as the proposal for mining and treating the bauxite. It is impossible to consider the Trombetas deposits in isolation. A regional account of bauxite in and around the Guyana Shield and the northern portion of the Brazilian Shield is included and it is suggested that these deposits all formed during Tertiary time under similar conditions.

Jan 1, 1977

By L. Diko-Makia, N. Rembuluwani

Artisanal and small-scale mining is crucial for the mineral sector in South Africa, but it also presents both opportunities and challenges. This paper presents an overview of the South African artisanal and small-scale mining sector, the socio-economic significance of artisanal and smallscale mining, the regulatory environment, and the environmental impacts, which are currently the status quo of this sector in South Africa. The paper identified ways in which artisanal and small-scale mining can support local development, create employment opportunities, and reduce poverty. The case of informatisation, ecological damage, and social insecurity has shown social conflicts, potential land degradation, and criminal behaviour. Finally, the paper discusses the future of artisanal and small-scale mining in South Africa, which will largely depend on improved legislation, enhanced personnel capacity, and more sustainable practices to ensure that the positive outcomes of the industry outweigh the negative ones. These propositions include recommendations to all stakeholders, including the government, industry, and civil society, such as stricter environmental regulations, improved working conditions for miners, and the promotion of responsible mining practices.

Dec 15, 2025

This paper talks about the experiences of groups we have worked with over the last few years in the Asia-Pacific region (Australia, Canada, New Zealand and Papua New Guinea) and the ways that they have worked to bridge the divide between traditional and introduced structures, governance at a regional level and the introduction of traditional values into monitoring and evaluation practices. In doing this these groups have created structures and processes which have helped them engage both more effectively with external stakeholders while maintaining the legitimacy of their own operations with their own constituents. These are important ideas for those involved in the mining industry that could provide a number of very tangible benefits to mining firms and their engagement with these kinds of groups.

Jan 1, 2009

By L. Yan, N. Damiano, J. Bickson, E. Bauer, D. Yantek, B. Whisner, M. Reyes, J. Srednicki

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35°C (95°F) [1]. The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by >5.6°C (10°F) in mines with elevated mine strata and air temperatures. In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35°C (95°F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy. INTRODUCTION The apparent temperature inside an occupied RA could be significantly affected by the surrounding environment’s thermal conditions, such as mine air temperature and mine strata temperature. Apparent temperature (AT) is a temperature-humidity metric for the perceived temperature caused by the combined effects of air temperature, relative humidity (RH), and air velocity. It is used to assess the perception of indoor temperatures. Depending on factors such as geographic location and season, mine air temperature, relative humidity, and mine strata, temperatures can vary significantly [2]. RAs located in cold mines may pass the 96-hour 35°C (95°F) AT limit test that poses a challenge for RAs located in hot mines. One solution in these cases is that the occupancy of the RA could be derated (i.e., the RA occupancy could be reduced) to ensure the AT limit is not reached. However, this would require mines to purchase additional RAs to accommodate all personnel in the mine. For mines with high temperatures (above 26.7°C or 80°F), the occupancy might have to be reduced so much that the necessary number of additional RAs would be impractical. In these cases, RA cooling systems could provide a solution.

Jan 1, 2019

By E. Fritz

This paper reviews the history, developments and 10 milestones of the oxygen steelmaking processes, with a special focus on conventional autothermic converters, high-speed converters with a blowing rate up to 5 m3n/t min and allothermic converters with coal addition, post combustion and the possibility to increase the scrap rate up to 50%. Related operating results are introduced. A new process route, which is based on hot metal and chromium ore, is outlined. The cost advantage for the production of 304 stainless steel grade is higher than 100 USS/t. The synthesis of EAF and oxygen converter steelmaking, a comparison of decarburization rates, refining combustion burners for optimized oxygen-management in EAF and an example for a large advanced EAF are outlined. Possibilities of flexible steelmaking and the growth and outlook of worldwide oxygen steelmaking are described.

Jan 1, 2004

By Harland E. Cofer

A computer-assisted resources and sedimentological study of the Andersonville, Georgia kaolin-bauxite district was begun in 1975 under a grant from the Office of Mineral Resources of the U.S. Geological Survey (Grant # 14-08-1110-G-173). A preliminary report on the kaolin and bauxite resources of the district has been placed on open file at the U.S.G.S. in Reston, Virginia; the Georgia-Geological Survey in Atlanta, Georgia; and Georgia Southwestern College in Americus, Georgia. In addition to a resources estimate, the objectives include the determination of the mineralogical variation, sedimentological parameters, and paleogeographic patterns of the deposition of the high alumina materials and their associated sediments. In the process of compiling data for the resources estimate, isopach maps were developed that provide information as to the shape, size, and distribution of the kaolin deposits and the kaolinitic sediments that contain them. These or similar maps developed for other districts can be useful exploration tools.

Jan 1, 1977

By Thomas A. Palmer

Free cyanide has been successfully determined in ground and surface water by isolation using a microdiffusion technique followed by a pyridine-barbituric acid photometric finish. The determinable free cyanide includes hydrocyanic acid, ionic cyanide, and the cyanide of weak complexes such as cadmium, lead, manganese, and zinc cyanide. Complexes of copper, iron, nickel, and silver are sufficiently strong so the dissociation into free cyanide does not occur at the microdiffusion pH 7. Cyanate, sulfide, and thiocyanate do not interfere. Samples containing as little as 0.005 mg/L are successfully analyzed. The relative standard deviation is <10%. Samples stored at pH >I2 in the dark are stable at least three weeks.

Jan 1, 1981