Search Documents

This report describes the new Bureau of Mines Core Repository System (CORES) and presents the methods for selecting, processing, and storing physical samples and descriptive data for future reference by earth scientists. The system preserves splits of chip samples and longitudinally sliced segments of core. A records retrieval system provides for storage of data on microfilm and magnetic tapes and uses the keysort parameters of location and commodity for the identification of data.

Jan 1, 1978

By George S. Austin

Adobe, dried mud bricks, have been used since before historic time in the construction of dwellings. Building materials are normally evaluated for thermal performance based on measurements known as R- and U-values. The R-value is an indicator of the ability of a wall to insulate effectively and the higher the R-value, the better it is as an insulating material. The U-value, or value of conductance, is the reciprocal of the R-value and reflects the rate at which heat is conducted through a material. But the "heat capacity of the wall" must also be considered. This measures the length of time that passes before a steady state of heat flow is achieved. The effective U-value measures both the resistance to the transfer of heat and the capacity to hold heat. These latter value make adobe a far more interesting as a modern building material that was formerly recognized.

Jan 1, 1983

By M. W. Pullen

It is recognized that the determination of electrical resistivity of the earth within a given area may furnish information concerning the location of certain mineralized strata of economic importance. Present knowledge of the electrical resistivity of the various rock formations is almost nil, and the geophysicist who is detailed to make a survey of an area without any data as to the relative resistivity of the underlying rocks is greatly handicapped. Such surveys are usually made within areas known to contain mineral deposits to aid in locating desirable points for drilling. Usually these areas have been prospected by diamond drilling, and drill cores of the various rocks and ores are usually obtainable. Were it possible to make resistivity tests in a laboratory of the drill cores or from pieces of the rocks and ore within an area before attempting a field survey, this would indicate not only the advisability for such a survey but would aid considerably in the interpretation of the results of such a survey. To be of most value a definite method should be used for all such tests, and as yet such a method has not been established.

Jan 1, 1929

The primary steel industry of the Prairie Provinces consists essentially of three companies whose total annual melting capacity, as of January 1, 1963, was 333,000 net tons. These companies have steel rolling facilities. In addition, there are five other companies producing steel castings by melting scrap in electric furnaces which, with the plants having rolling facilities, gives a total annual furnace melting capacity of 380,000 tons. Since 1954, the annual production of steel ingots and castings has ranged from a low of 66,588 tons, in 1954, to a high of 211,138 tons in 1961. The present facilities on the Prairies for making steel ingots from scrap, and rolling them to produce light merchant mill products, appear to be sufficient for many years ahead. Steel scrap, as electric furnace feed to make steel ingots for the present line of products, will probably continue to be available at reasonable prices either on the Prairies or from the north-central United States. It is recognized, however, that residual elements in scrap may be-come of greater significance and necessitate more rigid control of scrap quality.

Jan 1, 1963

By William Gleason

The mining industry is under immense pressure to not only meet increasing demand for minerals, but to do so in an environmentally safe and sustainable manner. Growth in electric vehicles, battery storage, renewable energy infrastructure and data centers to power artificial intelligence (AI) has led to an unprecedented demand for minerals such as copper, lithium, rare earth elements and others. The need for these minerals for national defense has only increased the pressure on the mining industry. Increased geopolitical tensions between the United States, China and Russia has added a sense of urgency as supply chains have become a focal point for the U.S. Department of Energy (DOE) and Defense (DOD) and other government agencies. The International Energy Agency (IEA) predicts that copper demand is expected to grow by 50 percent by 2040 while demand for lithium could increase eight-fold by 2040 and demand for nickel and cobalt could double. The challenges to meet the increased demand include technological, workforce, exploration and environmental issues. From Feb. 22-26, the global mining industry will converge on Salt Lake City, UT for the MINEXCHANGE 2026 SME Annual Conference & Expo where these challenges and others will be addressed by some of the leading minds in the industry. Included in this year’s conference is the Resilient Energy in Mining Symposium, a symposium with input from across SME that looks to address some of the most significant challenges the industry is facing. “Adopting environmental, social and governance (ESG) best practices has become a necessity for the mining industry, not an option. The Resilient Energy in Mining Symposium is crucial for MINEXCHANGE 2026 because it addresses the complex challenges of transforming traditional mining operations to support a sustainable and secure energy future,” Lisa Gonzales, principal engineering at Arcadias and MINEXCHANGE 2026 SME Annual Conference Chair and chair of the Resilient Energy in Mining Symposium said. “Mining is inherently energy-intensive, yet it is also foundational to the global energy transition, supplying the critical minerals needed for renewable technologies. By bringing together industry leaders, the symposium fosters collaboration and actionable change, showcasing advancements and real-world solutions that demonstrate the tangible benefits of resilient energy strategies. This unique forum enables knowledge sharing, inspires innovative thinking, and helps set the standard for sustainable practices across the sector.” The symposium was created in direct response to a SME member survey in 2023 conducted by the Responsible Mining and Underground Construction (RMUC) Strategic Committee. “The survey highlighted a strong demand for technical resources on energy transition, carbon reduction, renewable power, climate change, and ESG reporting,” Gonzales said. “To address this, I collaborated with RMUC to engage committee members from all SME Divisions, ensuring a diverse and comprehensive platform that reflects every aspect of mining. We intentionally structured the symposium to centralize key content and minimize duplication across divisions.”

Jan 1, 2026

By Sabert Oglesby, Albert L. Thomas

Until recently, probably the best means of sampling airborne dusts has been the impinger method. Dust-laden air is drawn into a sampling tube, and the particulate matters separated from the air and collected in the liquid in the impinger. A sample of the suspension is prepared on a slide and counted through a projection microscope. This method is simple and reliable, but it does suffer drawbacks. Since the collected particles must be counted visually, results of the dust count are taken. This seriously impedes studying the effectiveness of dust inhibitors, such as water sprays, or making adjustments in equipment. Greatest disadvantage of all, however, is the tedious task of counting particles in the sample. With the growing desirability of taking more samples, the effort involved in making these counts is a real factor in the cost of dust control. Finally, it is generally recognized that impinger dust counts can be related to health hazard only for specific kinds of dust and under similar conditions. This is because the rather complex mechanism of dust damage depends so much on size distribution of the dust. Counts determined by impinger samples cover a limited size range that does not necessarily correlate with retention by the lungs and upper respiratory tract.

Jan 3, 1959

By Wallace N. Thomas

The present interest in large diameter grinding mills and the rapidly rising cost of the drive in proportion to the cost of the mill establishes a need to explore the drive system in detail. The drive for a seven to eight thousand horsepower mill will cost from 1350 thousand to $600 thousand which represents nearly half the total cost of the mill package, and requires as much building space as the mill proper. Some of the drive components require a longer time to manufacture and the installation time and costs are equal to those for the mill. It is apparent that the drive has become a dominant factor in the overall mill design consideration. A new plant requires a tremendous investment in both time and money. With the high degree of competition in the mining industry, low capital cost is an exceedingly important factor in the development of a project. It is just as important, however, to insure that the equipment is going to perform satisfactorily for the anticipated life of the project without adding unplanned operating, maintenance and replacement costs. This is the position in which the engineer or designer usually finds himself and is really one of his primary functions -- establishing a realistic compromise between cost and performance.

Jan 1, 1969

By Harmon E. Keyes

Many organizations, including the Bureau of Mines, have made intensive studies of the application of leaching methods to relatively small low-grade disseminated deposits of copper ores, containing both oxide and sulphide minerals. One of the principal difficulties has been to obtain a solvent that could be made at a low cost and would effectively dissolve the copper minerals. Another drawback has been the high initial cost of a plant and the refined type of mechanism ordinarily required by standard practice for carrying out the leaching cycle. The Bureau of Mines has attempted to develop a cheap and efficient solvent that would especially meet the requirements of smaller plants. (See Bibliography.) It has been known that dilute ferric sulphate-sulphuric acid solution is an excellent solvent for most copper minerals, such as chalcocite, bornite, and oxidized forms, but not for chalcopyrite and certain silicates. A method of producing this solution from sulphurous products and waste liquors was developed by the bureau and tried successfully on a test-plant scale at the Southwest Experiment Station in cooperation with the department of mining and metallurgy, University of Arizona, Tucson, Ariz. However, this work did not involve the actual leaching of ores with the solutions thus produced or the cyclic use of the iron solutions in the regenerator cell. Except for certain laboratory tests, in which known impurities were added, no data were available to show the effect on regeneration if accumulations of impurities were built up in the leaching circuit.

Jan 1, 1930

By AIME AIME

ON the headwaters of the Hudson Riser, in a sparsely populated area of the north woods at Tahawus, N. Y., thirty miles from the nearest railroad, is the Maclntyre property of National Lead Co. Operations involve the mining and processing of titaniferous iron ore to produce ilmenite concentrate, and magnetite concentrate containing vanadium, for use in the production of iron, titanium, and vanadium in the war program. Accordingly, Maclntyre at present is classed as a war plant. More than 3000 long tons of ore is ruined daily by opencut methods and treated in an ore concentrating plant.

Jan 1, 1943

By T. A. Gray

The environmental liabilities of coal waste disposal sites can have a major impact on a mining project's economic viability. Developing a waste disposal site is no longer simply an exercise in completing paperwork to obtain a permit, with the proliferation of environmental regulations in recent years, managing disposal sites now requires design creativity, short term and long term planning and detailed monitoring to maximize the benefits to the mining company. Operating costs and future capital costs for expansion of existing sites, new site development and regulatory compliance should be reviewed periodically and considered in the overall management plan. This paper discusses various management methods that are being employed in the industry to improve waste disposal operations both environmentally and profitably.

Jan 1, 1994

By J J. Cilliers, K Hadler

Air is fundamental to flotation; not only is it required to collect the valuable particles, but it also controls the froth stability and consequently the separation performance for a given feed. Froth stability can be described and quantified in numerous ways, which are subtly different. Air recovery is one such measure of froth stability which accounts for both the stability of the bubbles and the mobility of the froth. The benefit of using air recovery as a measure of froth stability is that it exhibits a peak as air flow rate is increased, and this corresponds to the air rate at which the optimal separation performance is obtained. As such, it provides a single target value for optimising air flowrate for a given set of feed conditions. Use of air recovery, however, has one potential drawback: accurate measurement of the inlet air flow rate to a flotation cell is required. This can be problematic for operations, particularly where calibration of air flow rate is carried out infrequently or where there is no air flow rate measurement, such as for many self-aerated flotation cells. To this end, we present an alternative method for determining the peak in air recovery (PAR) air rate.We introduce a simplified method for determining the PAR air rate using trends in froth velocity and overflowing froth height, both of which are readily measured using existing froth image analysis systems. We will show, using industrial data, the application of this simple technique to find the optimal air flowrate for flotation cells. We will also discuss other alternative techniques for air rate optimisation that have the potential to improve separation performance using existing technology.CITATION:Hadler, K and Cilliers, J J, 2018. How to find the optimum air rate for flotation cells, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 377–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Thomas J. Peters

The King Mountain study area is centered about 120 air km northwest of Blackfoot, and 30 air km north of Arco, Idaho. The study area makes up the southern one-third of the northwest-trending Lost River Range--the highest mountain range in Idaho. The area is predominantly underlain by Paleozoic-age marine limestone and lesser dolostone, with a relatively small inlier of silica-rich, Ordovician-age quartzite. There are vast, unquantified resources of these industrial minerals present; however, special markets need to be developed for these resources which are near enough for transportation costs to be competitive. Five prospects were found in the study area; however, only one, the Elbow quartz silica prospect, contains resources and current claims. There has been no mineral production in the study area.

Jan 1, 1993

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars are characteristically of the "fire door" type that is frequently encountered on outside exit doors of many public and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they are required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in 'Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/ Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

By B Poborowski, A Chen

"For some time, the Australian and Chinese underground coal mining industries have evolvedindependently with minimal infl uence on each other. Despite the fact that in recent years severaltechnologies and solutions have become common to both industries, this trend has seeminglycontinued to the point that there are still many important diff erences in legislation and hazardmanagement systems in both countries. Austar Coal Mine as an Australian based and Chineseowned enterprise has a unique opportunity to benefi t from the technology and knowledge ofboth nations. This paper compares the Australian and Chinese approach towards spontaneouscombustion hazard management in order to exchange experience, identify possible improvements and learn from each other."

Jun 1, 2012

By Paweł Stefaniak, Natalia Duda-Mróz, Sergii Anufriiev, Wioletta Koperska

Due to the high environmental risks and negative impact of a failure, tailings storage facilities (TSFs) need constant monitoring. Advanced mathematical models have been developed in the past to predict the behavior of TSFs and raise alerts if needed. To be precise and reliable, such models need a spatial distribution of soil types within the dam as an input. Getting this data from laboratory measurements is time and costconsuming. In this article, we propose an ANN-powered algorithm, which allows us to accurately estimate the soil distribution based on a cone penetration test (CPT).

Jun 25, 2023

By Naeimeh Shabani, Hamid Mirzaie, Javid Sadeghi, Hoda Jafarizadeh-Malmiri, Afshin Javadi

Iron oxide nanoparticles (Fe3O4 NPs), despite their small size, are stable and have a large surface area that allows for absorption and removal of ions as well as turbidity in a short period of time. Thus, the present study addressed the synthesis and characterization of Fe3O4 NPs synthesized using the co-precipitation method and evaluated their effect on the coagulation process in water treatment. The Fe3O4 NPs characteristics were evaluated as follows: magnetic properties were measured using a vibrating sample magnetometer (VSM), surface area using Brunauer–Emmett–Teller (BET), crystal phase using X-ray diffraction (XRD), and morphology using field emission scanning electron microscopy (FESEM). In addition, the effects of the synthetic Fe3O4 NPs on the turbidity reduction of water in various pH levels were evaluated. The synthesized Fe3O4 NPs were without any impurity in the sizes of 22–32 nm, surface area of 99.6 m2/g, pores’ mean diameter size of approximately 10.6 nm, and maximum magnetic saturation of 66.21 emu/gram (emu/g). Using 0.2 g of synthetic Fe3O4 NPs with an initial turbidity of 17 NTU and pH of 6 could reduce all water turbidity (100%). Considering the cheap and facile production and separation, as well as the possibility to reuse them and reduce the sludge water content, iron oxide Fe3O4 NPs can be effectively used for turbidity reduction in the water treatment process.

Oct 26, 2020

By Robert Hopler

THE KEYSTONE NATIONAL POWDER COMPANY is an Independent organization, incorporated under the laws of the State of Pennsylvania. It has three dynamite mills near Emporium, Pa., with a daily capacity of 165,000 pounds. It maintains branch offices in practically all the largest cities east of the Rocky Mountains, and has distributing magazines located in every section where there is a demand for high explosives, with facilities for wagon deliveries. Our mills are all of modern type and are equipped with the most improved machinery for the manufacture of high explosives. The efficiency of our laboratory in conjunction with the high class of labor employed, has enabled us to put on the market an explosive, the quality of which is the result of extensive research and scientific knowledge. Our modern and complete equipment for harbor and railroad transportation insures our patrons of prompt deliveries, which is an essential feature particularly to contractors and those whose facilities for storage are limited.

Jan 1, 2013

By J. Pepin

When using alternating current submerged arc welding (SAW) to produce pipes from microalloyed linepipe steels, it is critical to balance penetration depth and deposition rates, in order to minimize the number of weld passes while still maintaining good heat affected zone (HAZ) microstructures and properties. A series of bead-on-plate (BOP) submerged arc welds were performed on X70 steel, using different waveform variable settings (i.e., balance, offset and frequency). Weld bead cross-section profile deposition and penetration areas were measured, and both Vickers hardness and Charpy V-notch impact testing were performed. Both single electrode and tandem electrode welds were evaluated.

Jan 1, 2011

By Jackson M. Langton

INTRODUCTION The Morenci-Metcalf district is located on the southern slope of the white Mountains in Greenlee County, Arizona. Both porphyry copper deposits are four to six miles northwest of Clifton, the county seat, and the new Metcalf mine is situated approximately one mile northeast of the Morenci open pit (Figure 1). Chase Creek, a south-flowing tributary of the San Francisco River, dissects the district and separates the two ore bodies. More than 1,200 exploration and development drill holes have been completed in the district and the Morenci-Metcalf ore bodies have been delineated on a 400-foot grid. Recently initiated drilling programs have revealed new data about deeper protore and associated hypogene alteration. This information, correlated with surface mapping and petrographic studies, was utilized to propose a plausible geochronologic sequence for this region. The reasoning behind this study has been helpful in locating new ore beneath leached capping indicative of only protore mineralization. The scope of this paper is to establish a practical solution to a highly theoretical problem of ore genesis and to familiarize the reader with stratigraphic, structural, and mineralogic events responsible for localizing ore in this district. Continued research will possibly alter the proposed time span and relative displacements, but it is doubtful that the order of events will vary significantly. Geochronologic conclusions are therefore presented as general hypotheses and additional geologic mapping,

Jan 1, 1972

By J. S. Brock

Magnetic, electromagnetic and gravimetric surveys have played an important role in the mineral exploration leading to the discovery of three major massive sulphide deposits in the Anvil-Vangorda area of the Yukon Territory. During 1964 and 1965 a saturation prospecting program, relying heavily on the integrated use of airborne and ground geophysical survey techniques, led to the discovery of the Faro deposit, which was subsequently proven to be a 63-millionton lead-zinc orebody. Locating the Faro deposit, the largest found to date in this overburden-covered region, involved an exploration sequence requiring the selection of a favourable geologic environment, aeromagnetic and electromagnetic surveys, property acquisition of anomalous areas and detailed ground geophysical surveys, followed by rotary drill testing, detailed gravimetric surveys and diamond core drilling.

Jan 1, 1973