Search Documents

By T. M. Morris

G. L. Simard and D. J. Salley—The authors and ourselves" independently came to similar conclusions both as to the value of tracer methods for the study of flotation and the general nature of collector-mineral interaction. The dodecylamine-quartz system appears to be simpler than the dithiophosphate-galena one, and the results therefore appear clearer. It is evident from a comparison of the two papers, however, that care must be used in extending the results to other more complicated systems. In the case of dodecylamine-quartz, the possible influence of micelle formation is of interest. There is no a priori reason why complete monolayer formation should necessarily occur at the concentration for micelle formation, since sorption depends on the nature of the substrate as well as on the properties of the solute in solution which alone determine micelle formation. Indeed, the fact that the onset of increased adsorption, point B in fig. 2, occurs at a concentration one tenth the critical value for micelles might imply that micelle formation does not have an influence. Interestingly enough, the data may be handled by the methods used for multilayer adsorption of gases on surfaces. Thus, if the amount adsorbed is plotted versus concentration, a sigmoid type curve is obtained, similar in form to a so-called Type I1 isotherm13 generally attributed to multimolecular adsorption. A monolayer value of about 0.12 mg per g may be estimated from the knee of this isotherm. On the other hand, if a plot is made according to the multilayer gas equation for adsorption to an unrestricted number of layers, eq 38,13 assuming the critical micelle concentration as the saturation concentration, the data above 120 mg per liter fall on a straight line from which a monolayer adsorption of 0.3 mg per g results. These considerations suggest that the monolayer may occupy an area somewhat less than the geometric value of 0.4 mg per g, and that micelle formation may indeed be a factor in the adsorption. the angle between the solid-liquid and liquid-gas interfaces, measured through the liquid. The value of the equilibrium contact-angle is uniquely determined by the value of the interfacial energies of the three intersecting interfaces and is independent of other forces in the system. When the liquid-gas interface intersects the solid at an edge—as was the case for all the experiments reported in this paper—the orientation of the solid-liquid interface is indeterminate or varies through 90" for a right-angle edge. Mr. Morris has called the angle between the horizontal and the liquid-gas interface for this edge condition a "static contact-angle." I feel that this term is unnecessarily misleading. In the first place, "static contact-angle" sounds too much like "equilibrium contact-angle." In the second place, the magnitude of the "static contact-angle," which I would prefer to call the "supporting angle," is determined by the forces in the system other than those derived from the interfacial energies, hence "contact angle" is misleading. If Mr. Morris had said that the "supporting-angle" is variable and depends on the weight of the particle and size of the bubble and that it has a maximum possible value equal to the equilibrium contact-angle, his discussion would have been more accurate. T. M. Morris (author's reply)—Mr. Kellogg puts forth a reasonable criticism of some of the terminology used in the paper. I agree that the term "static contact angle" may be misleading. Substitution of the term "supporting angle" or "vector angle" may be more suitable. F. X. Tartaron—In this paper the author presents a very interesting mathematical development of the forces present when a mineral particle adheres to an air bubble. Excellent concordance is obtained between mathematical formulation and experimental results. It is the writer's understanding that when the mineral surface presented to an air bubble is greater than the area of contact, the maximum contact angle is obtained. However, this contact angle represents distortion of the bubble, the normal shape of which is spherical or in cross-section, circular. This distortion produces a force that acts in opposition to the force of adhesion between the bubble and particle. Hence, at maximum contact angle, the force of adhesion between bubble and particle is at a minimum for static conditions. However, when the size of bubble is increased, the size of particle remaining the same (and all other conditions remaining the same), the contact angle decreases, the distortion of the bubble decreases and the force in opposition to adherence of bubble and particle also decreases. Thus, there is stronger attachment between bubble and particle. When this situation is applied to actual flotation conditions, it is doubtful that it has any significance. The reason is that the bubbles are normally so much larger than the particles, that in substantially all cases, it is probable that negligible distortion of the bubble takes place. In table IV, the author makes computations for bubbles from 0.50 to 2 mm diam. This is from 0.02 in. to 0.08 in. Certainly the bubbles generated in a flotation machine are far larger than this. The surfaces of the author's bubbles range from 0.79 to 12.6 sq mm. The area of contact of the glass rod (0.15 mm diam) is 0.017 sq mm. Thus, ratio of bubble surface to mineral area of contact ranges from 47 to 741 in round numbers. If we take a %-in. diam bubble and a 65-mesh (0.208 mm) particle of cubical shape, the ratio of bubble surface to mineral area of contact is 2931. Mineral particles do not readily become attached to air bubbles. Taggart has shown that in pneumatic flotation machines collector-coated particles are only temporarily attached to bubbles. They keep falling off and down in the froth but at a delayed rate as compared with gangue. Spedden and Hannan's motion pictures confirm the difficulty of attaching particles to air bubbles. In the agitation froth process, according to Taggart, air is precipitated from the water selectively on to the collector-coated particles and these

Jan 1, 1951

By R. H. Grau, C. D. Taylor, A. L. Martikainen

Utilization of belt air in underground coal mines has been discussed extensively during the last decade. The Final Report of the Technical Study Panel on the Utilization of Belt Air and the Composition and Fire Retardant Properties of Belt Materials in Underground Coal Mining formed by the Mine Improvement and New Emergency Response (MINER) Act of 2006 recommends research on leakage, use of booster fans, and escapeway safety. This paper discusses the role of ventilation modeling in evaluating primary escapeway pressurization in a three-entry development system to improve emergency escape in a coal mine using belt air. The intake entry of the National Institute for Occupational Safety and Health (NIOSH) Bruceton Experimental Mine was pressurized using a 1.1-m (42-in.) diameter, 37 kW (50 hp) fan. The work details air movement in the simulated three-entry system and the resulting leakage patterns. Three mine ventilation software packages were compared to analyze their performance in predicting the airflows and leakage conditions with different fan settings. NIOSH researchers found that the measurement results correlated well with the results of modeling.

Jan 1, 2010

By James R. Hunter, Sandra K. Zacharias, Ursula M. Franklin

Archaeometallurgical remains can be a valuable source of information about past technological activities and, by inference, the societies that undertook them. Material traces of former metal-producing or metal-working centres can include raw materials, products, or metallurgical installations such as mines, furnaces or forges. Of these remains, the most common is slag, often left undisturbed since its original production. Physical and chemical analyses of archaeological slag and metal can often reveal the processes and materials involved in their formation. Mineral composition and softening temperature of a slag, for instance, can indicate the conditions of the metallurgical operation, such as temperature and atmosphere and, thus, help identify metallurgical processes which took place at a site(1). The present report illustrates the value of such analysis. Metal-working remains from Sainte-Marie among the Hurons, near Midland, Ontario, on the south side of Georgian Bay have been analyzed in order to determine the techniques and processes used by the 17th-century blacksmith who worked at the mission headquarters from 1642 to 1649. Samples were selected from a very large collection of blacksmith refuse which was excavated from the site by archaeologist Kenneth Kidd in 1941-42(2).

Jan 1, 1999

By Rubén Alvarado

The markets and environmental protection rules are more and more exacting, both of which have determined that copper smelters should look for technological development and global management to ensure their viability and competitivity in the short and long term. The main facilities of the present and future Smelting-Converting Process at Codelco's Caletones Smelter, is based on Teniente Converter reactors with a high operational availability that have reached concentrate processing capacities near 2,000 tpd. These reactors are in operation in most of the smelters in Chile as well as in Zambia, Peru, Mexico and, in ?the near future, in Thailand. Since 1993, the Smelting-Converting process of the Caletones Smelter of Codelco-Chile has been based on one Reverberatory furnace, two Teniente Converters and four Peirce-Smith Converters. These facilities, together with the operation of two Fluidized Bed Dryers, three Slag Cleaning Furnaces, and two Oxygen Plants have allowed the smelter to reach concentrate smelting capacities and copper productions of 1,215 kt/year and 360 kt/year, respectively. This transitional operating scheme, combining together traditional and advanced technological equipment, needs further modernization to successfully face the modern world challenges, especially with relation to the environmental commitment, production costs and wide satisfaction of customers. For this reason, for the period 1997-2000, a Modernization Plan has been worked out. This plan considers an increase of the present throughput, which will permit a significant increase in productivity, as well as finding a definitive solution for meeting the environmental regulations. Among these projects, we can point out the definitive shut down of the Reverberatory Furnace, which is a contaminating piece of equipment of low energetic efficiency. Additionally, it considers the installation of two new Slag Cleaning Furnaces, one additional Oxygen Plant, and the incorporation of two new Sulphuric Acid Plants with a production capacity of 4,500 T/D, that will recover over 92% of the sulphur content, of process off-gases.

Jan 1, 1998

By Yuting Xue

Classification of rock and coal is one preliminary problem for fully automated or intelligent mining. It assists in automated rib stability analysis and enables the shearer to adjust the drums without human intervention. This paper studies the classification of rock from coal on rib images using machine learning techniques. A database of rock and coal images was created by filtering photographs taken by NIOSH researchers during site visits. Machine learning was conducted on patches, smaller images randomly extracted from each rock or coal image. After training, the classifier was validated with the testing dataset and achieved an accuracy score of 0.9.

Jan 13, 2022

By M. Moinpour, E. Liao, C. Y. Aw, D. J. Brown, P. W. Cheung

"Currently, silicon-based insulated-gate field-effect devices are being widely developed as the basic structural elements in a new generation of chemical microsensors. In this paper, we discuss some of the process considerations related to the fabrication of the Chemically Sensitive Field-Effect Transistor (CHEMFET). This ion-sensitive CHEMFET (or ISFET as it is often called) can be used for pH measurements (i.e., as a pH sensor) when the gate insulator of the electrolyte/insulator interface is made of Si3N4 obtained by the LPCVD method. Effects of processing parameters such as the Si3N4 deposition rate, gas composition, total flow rate, annealing treatment, etc. on Si/Si02, Si/Si3N4 and Si/Si02/Si3N4 structures are discussed in relation to the CHEMFET fabrication. Their effects on the electrical characteristics and chemical response of the sensor are also examined. Capacitance-Voltage (C-V) measurements and ESCA analysis have been used to interpret the results. The Si3N4/Si02 double dialectric layer provides improved ion blocking for the gate insulator in electrolyte solutions with enhanced pH sensitivity over time. The stability and performance of the fabricated CHEMFET sensors were tested by measuring the pH sensitivity in various storage conditions. The SEM analysis was used to evaluate the hydration effect at the ISFET's gate insulator with respect to different storage conditions.IntroductionThere has been a continuous interest in the development and fabrication of various chemical microsensors for chemical and biomedical applications over the last fifteen years. The application of semiconductor (particularly silicon) technology to the area of sensor fabrication has led to an emergence of a new generation of miniaturized, microelectronic, solid-state chemical sensors. There are numerous clinical situations where continuous monitoring of body electrolytes concentrations such as Na+, K+, Ca+2 , etc. and blood gases (pH, Po2 , and PC02) would be essential for the effective diagnosis and management of patients under critical conditions. Solid- state microsensors can be used for direct and continuous in vivo measurement of the above parameters in most instances."

Jan 1, 1988

By A. O. Sfriso

"Numerical modelling is becoming universal in rock engineering practice. Most applications focus on the prediction of failure loads of 2D problems, where the numerical models are useful extensions to analytical methods and experience-based design criteria. For 3D problems and problems where the assessment of serviceability indicators – displacements, ground-structure response, etc. – are of importance, the selection of the constitutive models themselves and the implications of the selection of material parameters may have a very heavy impact on the reliability of the model outcome and its predictive capability.This paper overviews basic common aspects of constitutive equations used in practical rock engineering and summarizes some challenges that are frequently observed when reviewing numerical models performed for routine problems in rock engineering. INTRODUCTIONNumerical methodsFrom a philosophical perspective models, either analytical or numerical, are idealizations of a perceived reality. For us engineers, models are just tools we use to guide our judgement and understanding of the problem in hand. When dealing with problems in rock engineering, we resort to a wide range of techniques:1. Closed form solutions like confinement-convergence methods for circular tunnels: these methods satisfy equilibrium and compatibility requirements at the cost of a crude simplification of the material behavior and geometry;2. Limit analysis methods, like bearing capacity formulas: lower bound methods satisfy equilibrium but sacrifice compatibility, and upper bound methods do the opposite. Material behavior must be simple, geometry admits limited freedom;3. Limit equilibrium methods, like method of slices for slope stability: they satisfy restricted forms of equilibrium, do not satisfy compatibility requirements, require simple material behavior but have a much greater flexibility on geometry;4. Numerical methods, where a mesh is employed to discretize the problem geometry: when properly formulated, these methods satisfy equilibrium and compatibility requirements and give reasonable approximations to the behavior of very complex geometries and construction sequences. Very little restrictions remain on geometry and material behavior, but the cost of calibrating the material parameters can be very high."

Jan 1, 2015

By M. Mohammadijoo, J. B. Wiskel, D. G. Ivey, S. Kenny, H. Henein

Cold-wire tandem submerged arc welding (CWTSAW) has recently been developed as a novel welding technique to replace the conventional tandem submerged arc welding (TSAW) process and improve the productivity of pipeline manufacturing. The process involves two electrodes with arcs and one electrically cold electrode. Since heat-input of the welding process is a key factor affecting the properties of the weld metal (WM) and the heat-affected zone (HAZ), and the additional cold-wire affects the heat introduced to the weldment, it is of interest to investigate property and geometry changes in the WM and HAZ when a cold-wire is added to the welding process. In the current research, the CWTSAW process is investigated and optimized by correlating the main welding parameters with the micro-hardness of the WM and HAZ and the geometry of the weld, i.e., the bead width (BW), penetration depth (PD), reinforcement area (RA) and coarse grained heat-affected zone (CGHAZ) area. Three statistical and mathematical methods are employed to optimize the CWTSAW process in terms of the mechanical properties and WM and HAZ geometry of a typical microalloyed steel used for pipeline manufacturing.

Jan 1, 2015

By Charles Seitz

The Bureau of Mines has modified its parts-per-billion helium-4 analyzer to improve the analytical capabilities of the instrument. The modifications resulted in the following improvements: (1) The analytical precision of the instrument for 10 consecutive analyses was improved to ±1 ppb at the 5,000-ppb helium-4 level, (2) the helium-4 sensitivity was increased almost tenfold, and (3) the minimum detectable limit for helium-4 was improved to 0.5 ppb. The modifications made to improve the instrument included replacing the ion-source control circuit with a direct-current solid-state design, controlling the temperature of the ion source, stabilizing and reducing the pumping rate of the vacuum system, and optimizing peak integration.

Jan 1, 1986

By Rhual L. Guerguerian

MINING has been practised by mankind for over sixty centuries (1). In 1876, the "ball mill" was patented, and during the century that followed rotary grinding developed to the state where individual machines are treating tens of thousands of tons of ore per day. This paper gives a brief description of design practices prior to the availability of advanced facilities, followed by modern analytical design development at Dominion over the past ten years.

Jan 1, 1978

By Alphonso Cornejo, Galen H. Clevenger

This bibliography was compiled in connection with an investigation of the Caron process for the treatment of manganese - silver ores , conducted by the T. S. Bureau of Mines in cooperation with the Netherlands East Indies Government . The object of this investigation was to develop a practicable method for treating the refractory manganese- silver ores found in these two countries . The results of the work will be published as a bulletin of the Bureau of Mines . This bibliography summarizes the available information on the subject previous to the investigative work embodied in the forthcoming bulletin, and may be useful to those metallurgists or others conducting work along this line .

Mar 1, 1923

By E. Ozberk

The copper and nickel smelting industries are important contributors to the technical and economic well-being of Canada while some of the smelters are among the largest sources of sulphur dioxide emissions in Canada. A review of the operations in six smelters - Falconbridge Limited, Falconbridge, Ontario; Hudson Bay Mining and Smelting Co. Limited, Flin Flon, Manitoba; Inco Limited, Copper Cliff, Ontario and Thompson, Manitoba; Noranda Mines Limited, Horne Division, Noranda, Quebec and Gaspe Mines Division, Murdochville, Quebec - have shown that about 80% of the total sulphur input to these smelters was emitted to the atmosphere in 1980. A simultaneous review of the existing and emerging technologies which can directly or indirectly reduce the sulphur dioxide emissions indicated that it is possible to reduce the emissions to below 20% of the sulphur input to these smelters. This can be achieved by varying degrees of modifications to the smelting operations and installing sulphur fixation facilities at significant costs which may increase the metal production costs. This would consequently make the competitiveness of the Canadian copper and nickel producers more difficult in the already tough world metals market.

Jan 1, 1983

By Nelson M. Solow

Raise boring of mine ventilation shafts in many cases offers a lower cost and higher speed method of construction in comparison to conventional shaft sinking. Where underground access is available for raise boring the potential savings indicate that raise boring should be considered as an alternative to other methods. Raise boring machines are currently in use which have the capability for reaming shafts up to twenty feet in diameter, depending on the strata and depth. These large capacity machines make it possible to consider raise bored shafts for moving large volumes of air. Although we will consider here only ventilation shafts, raise boring should also be considered for men and material shafts. When the mine planner has determined the volume of air required through a shaft at a particular location he is faced with the problem of selecting the shaft size. The principal factors in optimizing the shaft size are the construction costs for the shaft 'and the power cost to move the air through the shaft. The larger diameter the' shaft is the more it costs to construct, but for a given volume of air the power required (cost) becomes lower as the diameter increases. The construction cost is paid only once, when the shaft is constructed. The power costs, however, are paid throughout the life of the shaft. Methods of optimizing air shaft size found in the literature (References 1 and 2) amortize the construction cost and include it in the average annual cost of operating the airshaft. These methods derive a formula for the average annual cost vs. shaft size and de-rive the formula to compute the optimum size for a given air flow rate. It is, however, desirable to take into account tax considera-

Jan 1, 1977

By M. Stachowiak, M. Nowicki, K. Walas, A. Skoczylas, P. Stefaniak

In this paper the authors present a walking robot dedicated to the inspection of a belt conveyor’s transportation system in an underground mine. The developed robot can independently diagnose all of the key rotating elements of the belt conveyor (pulleys, bearings, drums, gears, engines) based on vibration and acoustic signals as well as typical RGB (red, green, blue) and thermal images. The article presents key diagnostic procedures applied to real industrial data obtained during robot testing.The work was developed as part of the ‘THING–subTerranean Haptic INvestiGator’ project. The authors presented the main assumptions of the research methodology developed for the needs of technical diagnostics of conveyor elements typical of inspection work performed by mining staff. Based on industrial data, the use of algorithms for elements such as rollers, drive stations, and the conveyor belt were shown. The main assumption of the research is to develop a robot adapted to the conditions of a deep mine, capable of carrying out an autonomous inspection of mining infrastructure. The conducted tests and the developed fault detection algorithms were aimed at preparing the robot for underground tests in the operating conditions of the mine.

Sep 1, 2021

By S Hapugoda, A Edenton, M Adam, R J. Holmes, J R. Manuel, R Smyth

Lump ore is one of the key ferrous feeds used in the blast furnace ironmaking process, normally accounting for ten to 20 per cent of the blast furnace burden. Like other feeds, the characteristics of lump ore have an important impact on the stable operation and productivity of the blast furnace. Lump ore is usually assessed chemically, physically and mineralogically to establish its likely blast furnace performance. The physical characteristics of lump ore are strongly related to the chemistry, mineralogy and texture of the ore involved. In this paper, the blast furnace ironmaking process is reviewed, with particular emphasis on the key quality requirements for the ferrous burden material. A variety of key physical characteristics of lump ore measured using standard and non-standard methods are then described and subsequently correlated with the chemical and mineralogical characteristics of the ore wherever possible. Finally, the impact of these physical characteristics on blast furnace operation is assessed.

Jan 1, 2009

By N. Giguère

Until recently, the heat treatment of pressure die cast parts has always been considered unpractical because the solution heat treatment resulted in unacceptable blistered parts. This was due to the presence of massive porosity associated with the die casting process where the inflow of metal inside the mold cavity is extremely turbulent. With the steady improvement of foundry practices and the generalization of vacuum die casting, porosity defects have been reduced to the point that a partial solutionizing heat treatment can be applied without any damage to the casting. However the solutionizing temperature must be lower than that applied to macroporosity free castings and for much shorter time. The object of the present study was to determine the optimum solutionizing temperature that can be applied to aluminum 383 die cast brackets along with the optimal temperature and time of aging resulting in the highest improvement in mechanical properties (both strength and ductility). This was done by testing strength and deformation on the casting itself using a specially designed jig; the crushing force to deformation curve was analyzed so as to quantify the improvement in both strength and ductility gained with the partial precipitation hardening heat treatment.

Jan 1, 2011

By F. E. Bedale

STUDY of several severe mine explosions that occurred during the winter of 1907 led to the belief that coal dust was a definite explosion hazard. The Consolidation Coal Co. was a pioneer in the early work to' eliminate this hazard and to combat the dangers incident to poor ventilation and the presence of methane. Maintenance of high humidity throughout the mines was one of the first measures adopted, later to be superseded by rock-dusting. In the twenty years from 1907 on, many safety measures were developed and adopted, and several prizes were won, though the practice was crude by present-day standards. But in 1927, the company went to work in earnest, and organized a Department of Safety with adequate personnel and with authority to enforce all approved rules for the prevention of accidents and the preservation of company property. All plans for new construction work, changes in mining systems, and proposals for the purchase of new mining equipment had to receive the approval of this Department. A set of operating- and safety standards was written to govern the activities of all employees, and physical examinations for them were required.

Jan 1, 1938

By V. Estrada, G. Aguilera

"Since the most of mineral processing are wet, and for more specific applications where it is necessary to increase the purity through leaching and / or concentration, the proper dispersion is the first, and perhaps more crucial stage in the whole chain of processing. This specific process is based on the formation of a dispersion or suspension of mineral, trying to make the mixture as homogeneous as possible, and with specific rheological conditions. Sometimes it is not enough agitation to make it happen, so that chemical additives are used as an aid. However, the addition of chemicals strongly alters the viscosity and other rheological properties of the suspension factor to consider for subsequent steps to ore beneficiation. In other hand, in a process where no chemicals used often employ large quantities of water to achieve dispersion. But if an efficient chemical agent, which optimizes said dispersion through a specific physicochemical effect on the particle surface is used, also it can generate rheological advantages, besides achieving rational use of water and increase the recoveries of the product main about also optimal costs. The aim of this work is to find the optimal rheological conditions for a dispersion of kaolin as study case, looking for stability, best disaggregation, viscosity and pseudoplasticity.To find the optimal additive, the evaluation parameters were: 1) Best degree of dispersion of the suspensions according to the analysis of the flow curve; 2) Best level of disaggregation of particle chemical analysis delaminated by Particle Size Distribution; and 3) Best thixotropic rheological parameters and pseudoplasticity. Finally the optimum additive as one that meets the best combination of parameters is proposed.INTRODUCTIONKaolin is a clay material formed by altering of feldspar composed mainly for kaolinite. Depending on the application, the kaolin as raw material must be refined and processed because the ores of clays contain usually a lot of impurities derived of its sedimentary source, such as feldspar, mica and quartz (Torres, et. al., 2011). According to the experience on the plant floor and the publication of several scientific papers, it is known that the dispersion is a crucial stage in mineral processing (Greene, Duke, & Hunter, 1965) (Raghavan, et. al., 2004), not only because of the disaggregation of particles, besides because of the humectation of them. Is clear that disaggregation of particles give to the suspensions rheological stability, and the humectation improves the effect of further processes like grinding or chemical treatment. The dispersion process involves making a suspension of the mineral with a solvent which is usually water, to obtain a homogeneous dispersion, with the aid of energy of stirring. Sometimes is not enough the agitation (even with high energy) for this to occur, so is necessary the use of dispersing substances which introduce ions and molecules as modifiers of chemical potential, forcing the molecules of the material to disperse. Sometimes their use even could affect the pH of the suspension in a non-desirable condition. (Flores, 2013)."

Jan 1, 2016

By Volovik A. V. Ivtan, Shelkov E. M. Ivtah

"One of the most power consumption Industrial process is production of Al from bauxites (about 45000KWt.hour electrical energy for production of 1 ton. of technical Al). This process is based at the low efficiency and productivity electrolysis technology.Last years IVTAN investigations give to .us information about possibility to use of high temperature shaft- furnaces for efficiency production of alumina (AL2O3 ) technical. aluminium and some all.oys on the base of the high temperature carbon- thermal reduction process. At this case power consumption for production of unit of last, product will be less at the 3-4 times.The carbon-thermal method is allow produce alumina (Al203 ), technical Al and its alloys not only from deficient bauxites, but practically inexhaustible reserve of other types of Al-contain row materials (cianite, sillimonite and so on/The thermal-chemical economical analises of fulfilled at the IVTAN, production of alumina. Base on facts of production and technical technology are especially for ones arguments at the high temperature shaft-furnace technical Al and its alloysIn the last decades of the 20-th century, the discharge into atmosphere of high temperature and. combustion gases places . problems before humanity more and more sharply and becomes of great importance task.But at the same time, as production of material values increases, intensity of pollution of environment increases all time. And the value of new processes and. technologies of material production, aimed at reducing the expenditure of power and pollution of· the environment, also increases."

Jan 1, 2000

By Richard Kojo Gabah

Western mining companies are entering an African critical minerals market where access is harder to secure, risk is being priced more sharply, and execution advantages are increasingly decisive. The continent holds significant reserves and production potential of cobalt, lithium, copper, graphite, manganese and rare earths critical to the energy transition, yet Chinese-aligned capital has built a structural edge in access and execution speed. Simply signing narrow offtake agreements to buy output is no longer sufficient. Western firms win when they convert quality orebodies into bankable projects by reducing aboveground risk faster than competitors through integrated infrastructure access, durable fiscal alignment, and credible local value creation. Western mining companies will break into Africa by pairing capital with partnership, building corridors enabling infrastructure and power, designing credible value addition pathways and operating in a way that is politically durable through transparency, community benefit and fiscal terms that share upside in commodity upcycles. This feature article offers a practical playbook for mining executives and investors. The core argument is straightforward. Winning in Africa requires competing on the full system around the mine. Corridors and power, processing pathways, contract durability, community benefit and regulatory execution are now decisive variables in project valuation and capital access.

Mar 1, 2026