Search Documents

By J. W. Paul

This paper deals with the second phase of an extensive research on coal-mine ventilation factors. A comprehensive report of the entire work is in course of preparation, but abstracts of the various chapters are being prepared in order to make the results public as rapidly as possible. Part 1 dealt with the resistance of unobstructed entries and was issued as Serial 2621 of the Bureau of Mines, in July 1924. Description of tests. After the resistance of an unobstructed entry to flow of air had been determined by tests in the Experiment mine, mine cars were; run into the test section in various arrangements and the increase in resistance was determined. The cars used were of the wooden type with loose end gate, and would hold about one ton of coal, level full. They were 7 feet long. 4 feet 2 inches wide above the wheels, 3 feet high, and had a cross-sectional area of approximately 10 square feet. The average area of the entry was about 57 square feet, the ratio of unobstructed to total area being about 17.6 per cent. The track gage was 42 inches and the wheel-base 20 inches.

Jan 1, 1924

By J Borthwick, M Yusi, M Douge

Feasibility studies form a vital and significant component of the project delivery cycle. They are at the heart of the valuation process. This paper focuses on variables which can affect a project and how these are assessed as part of the decision-making process through feasibility studies. Test work and site selection needs; the degree of engineering required to meet the study requirements and the quality of owner project information are discussed. Also, local factors including permitting needs, social, environmental and government relations are considered. Engineering and site factors are crucial in the estimating process. The interaction of detailed engineering, engineering assumptions and estimating methodologies are therefore examined. The ownerÆs perspective is considered along with risk analysis, which is fundamental in project feasibility study activities. The impact of this is also discussed.

Jan 1, 2009

By Rick Deschamps, Amanda Blank, Matthew W. Drewek, Michael P. Walker

The Prairie du Sac Dam, located on the Wisconsin River, northwest of Madison, Wisconsin, was constructed 1912-1914. The spillway is an Ambursen-type, consisting of a series timber pile supported pier and buttress walls and rollway slab. The timber piles supporting the spillway, numbering approximately 5,000, have deteriorated, and the spillway structure was underpinned with over 700 micropiles as part of a design-build construction project. The underpinning micropiles needed to be arranged to avoid interferences with the existing timber piles, requiring the micropiles to be installed in the open spaces between the piers and buttresses. Inevitably, the installation of the new micropiles encountered obstructions, including existing timber piles out of alignment, as well as timber piles used to support the original construction activities and sheet pile used to control water during the original construction. This paper discusses using finite element analysis to model the spillway structure to estimate the vertical and horizontal stiffness with an extensive sensitivity analysis was performed during the design phase to account for anticipated construction challenges and potential variations in the underpinning performance. The inherent rigidity of the spillway structure allowed for load distribution to the underpinning system even when new micropiles needed to be re-located and aligned to avoid interferences with existing timber piles and other abandoned foundation elements dating back to original construction.

Sep 8, 2021

By I. V. Shadrunova

Annually it is formed more than 95 Mt of clinkers in iron and steel industry of Russia, including 79 Mt of clinkers in blast-furnace, steelmaking, foundry and ferroalloy productions. Complex development of clinkers will provide not only extraction of valuable components, but also preservation of ecosystems. Processing of solid slags is realized, as a rule, in a cold condition by mechanical methods only including stage-by-stage crushing of slag on devices, working on principles of compression and shift (jaw and roll crushers). However it doesn?t provide the complete extraction of metals from clinkers. The intensification of decomposition, in our opinion, can be provided under the use of the devices working on a principle of free kick. At such influence on a material, its destruction occurs on micro cracks, sides of cohesion that is there is a selective destruction of the components possessing various resistances to impact. Decomposition of a piece on the basis of free kick about a material or metal is realized in centrifugal-shock crushers and mills of research-and-production association ?Ural Center?. The share of the joints sharply lowering the efficiency of enrichment thus is minimal. The efficiency of application is proved by morph-metrical measurements with the help of system of image analysis ?SIAMS-600? and physical-mechanical tests of clinkers and their components (impact strength, micro hardness). The experience of application the devices of centrifugal-shock crushing for processing clinkers in blast-furnace, martin and converter productions of Open Society MMC, clinkers of rough-edged copper melt of Joint-Stock Company "Karabashmed" and aluminium clinkers of Joint-Stock Company « Samara plant of aluminium alloys » has allowed to confirm the efficiency of application these devices for selective decomposition of metallurgical clinkers and the opportunity of using clinkers as resource of ferrous and nonferrous metallurgy.

Jan 1, 2014

By D. R. Babich, E. R. Bauer

National Institute for Occupational Safety and Health (NIOSH) researchers are conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry. Surface and underground limestone is one commodity recently surveyed. The sound levels of mining and processing equipment were recorded to identify noise sources. Full-shift worker noise exposures were completed to determine the exposure of various occupations. This paper presents the results of the noise research conducted in both underground and surface limestone mines, detailing the equipment likely to cause worker overexposures, and the occupations experiencing overexposures. Implications for worker noise exposure reduction are also reported.

By J. G. M. Mukoya, B. Adebayo

"This work was carried out to determine the influence of rock properties and drilling machine parameters on the penetration rate at the SJ pit of Rössing Uranium Mine, Namibia. Rock properties (uniaxial compressive strength, tensile strength, and modulus of elasticity) of samples collected were determined in the laboratory. Drilling experiments were conducted in which feed pressure, air pressure, rotary speed, weight on the bit, and torque were varied to measure their effect on the penetration rate. The uniaxial compressive strength varied from 90–180 MPa for layered marble-quartzite and banded gneiss. Increases in feed pressure, weight on the bit, and rotary speed beyond the optimum level led to a decrease in penetration rate and caused the drill bit to ‘stall’. Results of the study revealed that penetration rate increases with an increase in the feed pressure and air pressure. After reaching a maximum value, the penetration rate begins to decrease despite increasing feed pressure. A very high torque causes the drill bit to stall, since the feed pressure is too high and the air pressure is not sufficient to remove the cuttings from blast-hole at maxium bailing velocities. The average penetration rate varied from 19 to 45 m/h for phase 2 of the pit, and from 17 to 68 m/h for phase 3. The optimum drilling machine parameters obtained in phase 2 and phase 3 were slightly lower than those currently being used at the mine. The trials of the optimum machine parameters will assist in reducing the cost of drilling, which varied from N$29.48 to N$36.31 per metre for the tricone bit. IntroductionDrilling and blasting contribute most to the operational cost in opencast mining and have the potential to influence the cost of downstream operations (Aipanda, 2011). The drillability of rocks depends not only on the rock properties, but also on the drilling tools and operational variables. In rotary drilling, rotational speed, thrust, and flushing are the operational variables, and are known as the controllable parameters. Rock properties and geological conditions are the uncontrollable parameters. Although, many attempts have been made to correlate drillability with rock properties, the rock characteristics affecting rotary drilling have not been entirely defined (Hartman, 1962; Kahraman, Bilgin, and Feridunoglu, 2003). The drill bit is forced into a rock surface from the rotary power head, hence creating stresses and cracks at the bit-rock interface. The performance of a particular bit in any formation i"

May 1, 2019

By Diego Quezada, Carlos Munoz, Marco Arellano

It is well-know that the presence of fine materials in mining has a direct impact on the plant processes with a great influence in the total amount of ore production and recovery. In Cu mining heap leaching is affected negatively by the presence of fines material (< 100 # Ty) in leaching piles, where a decreasing in Cu recovery is achieved in a lot of cases. D&B practices used normally in mine operations can generate fines > 4% in blasted piles, but the principal effects are reflected in the downstream processes where pre-conditioning post-blast materials release greater quantities of fines.

Jan 1, 2010

By Willard L. Hunter

The Bureau of Mines studied the effect of temperature upon the reduction of chromite by carbon and the relative reducibility of chromites as a function of their composition. Ferric oxide was also studied to provide comparative data. Pellets weighing approximately 1 gram and containing 70 percent ferric oxide, chromic oxide, or chromite and 30 percent graphite were subjected to closely controlled temperatures under a flow of argon for 15 minutes. The amount of CO and CO2 evolved was measured, and the reduced sample was analyzed by X-ray diffraction techniques. The reduction of Fe2O3 was studied over a temperature range of 600° to 1,400° C, while the reduction of Cr2O5 and chromite was conducted from 9000 to 1,621° C. The temperature above which appreciable reduction of Cr203 by graphite took place was 1,125° C. The temperature at which significant reduction started for three of the four chromite samples was approximately the same, indicating that there was concurrent reduction of iron and chromium oxides in the chromite mineral rather than selective reduction of iron oxides followed by reduction of chromic oxide. Rhodesian chromite appeared to dissociate at a lower temperature with concurrent reduction of iron. Based on the temperature at Which chromite was 50 percent reduced in 15 minutes, Transvaal chromite reduced most easily, followed by Mouat, then by Kampersian, and finally by Rhodesian DFC material. Statistical analysis of test results indicated that the ferric iron content of chromites affects their reduction behavior more than any other constituent.

Jan 1, 1966

By SIDNEY ROLLE

ACURSORY glance through the literature on the subject reveals that the ablest minds in the land are devoting themselves to the great question of labor, of which employment is one of the fundamentals. Volumes have been written and the end is not in sight. Employment management is today about in the position that efficiency was 15 years ago. During the early days of the war, and perhaps for a year or so before, labor was plentiful. As the war progressed and Europe drew on us for munitions, employers began to compete with one another for&apos;, all, classes of labor. Labor was difficult to obtain, wages rose, the labor turnover increased, and employers began to install employment departments, welfare plans, and all sorts of schemes, but the labor efficiency dropped. As the war progressed, greater and greater production was demanded. New factors were introduced each day. The government, labor unions, industrial councils, all tended, it seemed, to make the situation almost intolerable. Wages rose to fantastic heights, the cost of living rose higher and higher, and the efficiency dropped still further.

Jan 1, 1921

By James J. Dowd

During and immediately following World War II, the heavy demands for steel required the mining of unusually large quantities of coal for the manufacture of metallurgical coke. The largest demand for metallurgical coke is in the Appalachian region, which comprises central and western Pennsylvania, Maryland, West Virginia, Virginia, eastern Kentucky, Tennessee, and Alabama. This demand is satisfied by coke made from coals within the region; consequently, the reserves of coking coal in this region are being depleted more rapidly than reserves in other coal-producing regions. The supply A&apos; high-quality coking coal during the war was inadequate, and some coke were forced to use inferior coals. The coke produced from these inferior coals adversely affected the rate of production. Another national emergency probably would produce a similar condition, and in the interest of -national security, the Munitions Board of the National Military Establishment requested the Bureau of Mines to evaluate the reserves of coals suitable for the manufacture of metallurgical coke. All bituminous coals in the Appalachian region are coking, and as the coal that produces the better metallurgical coke become depleted, other coal previously considered inferior will be used. The general trend is toward the use of lower-quality coals for metallurgical purposes.

Jan 1, 1950

By B. Wasmund, M. Parravani, M. Jastrzebski, Z. Coull

"One of the main drivers of overall profitability of pyrometallurgical vessels is refractory lining campaign life. Increased economic pressure to improve vessel life requires innovative solutions to the problem of refractory cooling. Hatch has recently developed a high-intensity, waterless cooling system that bridges the performance gap between external shell cooling and internal water-cooled copper elements. External shell cooling has a limited effectiveness in protecting the refractory lining, because it is thermally insulated from the hotface of the lining by its thickness. This situation does not improve until the lining itself has become worn near the end of the campaign. The patented technology developed by Hatch overcomes this problem by positioning high-velocity air-cooling channels within the lining, closer to the hotface where the cooling benefits can be realized throughout the entire duration of the campaign. The current paper presents the development and application of Internal Air Cooling technology as well as results from the pilot campaign in an operating commercial vessel. Various adaptations for this novel, cost-effective and inherently safe system are also discussed."

Jan 1, 2015

By R. G. Nelson

The mechanical properties of low-hafnium, arc-melted, Kroll-process zirconium are presented. The effect of temperature on the ultimate strength, yield strength, proportional limit, elongation, hardness, Young&apos;s modulus, electrical resistivity, and impact strength are shown, The effects of cold work and annealing on the tensile properties, bend radius, and formability, as determined by cupping tests, are also given, Tensile properties are compared, in part, to those obtained on earlier graphite-melted zirconium and on crystal-bar zirconium. INTRODUCTION The commercial production of high-purity, low-hafnium bearing zirconium has been achieved, and this metal is becoming available for industrial use. However, there is little published information regarding the physical and mechanical properties of this product; and, since there have been many improvements in the production and arc-melting techniques of zirconium in the past 3 years, it was considered advisable to present the properties of the vastly improved zirconium representative of current production.

Jan 1, 1954

By J. Kraemer, A. Preusse

In the federal state of North Rhine Westphalia (Germany) small and medium sized companies are beginning to extract the related gas via old shafts or boreholes and to use it as a source for the production of electricity and heat. More than 100 applications for the separate mining right on mine gas had already been filed by beginning of 2002, since mine gas is treated as a mineral resource under the Federal Mining Law. Meanwhile more than 40 mine gas concessions have been granted and first projects are being developed with encouraging results so far. To enhance the applied techniques and their efficiency Aachen University has formed a research team in this discipline. Scope and goals of this research activities are being presented in this paper. Keywords: extraction mine gas, Renewable Energy Act, Ruhr District.

Jan 1, 2003

By I. L. Jennings

In most industrialized countries, the largest element of the mining industry in physical volume is that devoted to the extraction and processing of materials for use as construction aggregates. Required for all developments in industry and commerce, power and transportation, and housing and public services, their use is so widespread that possible sources are exploited throughout all geographic regions, as close as possible to the point of use. Thus, it is also the most frequently encountered form of mining throughout the world. These materials come from four main sources:- (a) Excavation of unconsolidated deposits of sand and gravel (b) Stone quarrying. (c) Processing of slags and other mineral wastes. (d) Manufacturing from clays and shales by heat fusion. The major uses are in: (a) Portland cement concrete, that most versatile of construction materials, including the many concrete products in current use. (b) Asphalt cement concrete; widely employed for paving roads, parking lots, airfields, etc. (c) Foundation materials, such as road base, granular backfills, railway ballast, etc.

Jan 1, 1968

By Tristan Worsey, Nathan Rouse, Daykin Schnell

The authors were retained by a proposed underground metals mine operation to evaluate the potential blast vibration amplitudes that could be generated at surface structures above the proposed mine. Literature reviews of published blasting documentation gave little information, data, or models on surface blast vibrations produced by underground mines. At the client’s request, the authors contacted a number of underground mining operations to evaluate interest in sharing blast vibration data with the authors so that the authors could develop an underground-to-surface blast vibration regression equation.

Feb 1, 2020

By G Capes, L Morizzi, N Mitkas, E Jones, D Grant

This paper describes the mining setting for the sub-level open stoping (SLOS) mining method used at Olympic Dam (OD), and investigates the range of stope performance conditions encountered over 30 years of production, using a qualitative description of the factors influencing performance. Utilising a continuous improvement tool, the Plan-Do-Check-Act (PDCA) process, and a forward-looking rock mechanics program, the intent is to identify the key factors driving productivity and performance to create a stable and achievable long term mine plan.

Mar 15, 2021

By Dwayne D. Tannant

This paper presents a new mining concept for oil sands called ?hydraulic underground mining of oil sands? or HUMOS. While this mining method is still at the conceptual stage it has great promise to allow extraction of bitumen from areas that are currently uneconomical or technically infeasible using surface mining or steam assisted gravity drainage. HUMOS is founded on a combination of recently proven technologies such as directional drilling, water jet cutting of oil sands, slurry transportation, cold water extraction of bitumen, and thickened tailings. One key component in the mining concept is the caving of oil sands and the creation of an underground cavern. Scaled-down physical models will be designed and built to demonstrate water jet cutting, cave development, and insitu primary bitumen separation. These will be used as a &apos;proof of concept&apos;. On-going research will establish and prioritize issues that need to be resolved, outline key areas where further research is needed, foster establishment of research teams to divide and conquer the important questions, and create framework for future coordinated research efforts.

May 1, 2001

By H. OSBORG

THE patent literature of alloys for the last two decades or so indicates that the number of liatents referring to smaller and smaller percentages of essential alloying constituents is on the increase, whereas the number of patents relating to considerable percentages of alloying additions becomes smaller. The claims regarding physical properties indicate consistently higher and more rigid values and show the possibility of modifying the physical properties by only slight changes in the percentage of minor constituents or by applying different methods - of treatment. Alloys of the same base have been made suitable for a number of different applications by intelligently and rigid- ly controlling their composition, melting, casting, working, and heat-treatments. Other trends indicated in the development of modern alloys are higher corrosion resistance, higher fatigue limits, and "stability" in volume.

Jan 1, 1937

By M. J. McPherson, P. Mousset-Jones, G. Danko, F. Calizaya, K. You

The friction factor is one of the more difficult parameters to determine in ventilation planning. In practice, this can be estimated from published factors such as those of McElroy. The problem with this approach is that the selection requires some judgement, and the estimated values offer no more than guideline accuracy. This study, examines the effects of four factors on the coefficient of friction for a simulated mine airway. The factors are: airway cross-section, asperity height, flow direction, and cross-cut spacing. The study includes the modeling of a mine airway and the evaluation of the results from 13 experiments on flows of air over rough surfaces. The model, physically represented by a wind tunnel, includes a rough surface section which can be modified to simulate mine airways of various shape and asperity height. Most of the experiments were performed under controlled flow conditions during which the Reynolds number was varied between 50,000 and 300,0000. Based on this study, the friction factor for a mine opening was found to depend not only on the size and shape of the surface asperities but is also affected by the orientation of them in relation to the flow direction.

Jan 1, 1991

By B Waldon, M Valastro

A coal dust explosion is one of the most significant risks in the harsh and complex environment of an Underground Coal Mine (UCM). Reviewing literature, regulations and existing systems surrounding explosive dust management shows that there have been few advancements in managing this risk over the past 90 years. Legislation has remained relatively stagnant and minimal systems are implemented in the real world that can simplify, standardise and improve the effectiveness of UCM explosive dust management. To help bridge this gap, Corehesion, in collaboration with an UCM has designed, developed and implement an Explosive Dust Risk Mitigation System (EDRMS) utilising components of Business Intelligence (BI) that is capable of real-world use in industry. To do this the existing explosive dust management process at the associated research mine was evaluated to form high-level and detailed design requirements, focusing on digitally simplifying the procedure, not replicating it. The system was then iteratively and incrementally developed and implemented at the research mine to commence real-world use. The developed BI platform is compared with the existing process to highlight the advancements in performance transparency, efficiency and optimisation of UCM explosion mitigation. This comparison and evaluation of the real-world system implementation at the research mine demonstrate its success in automating procedure steps, providing a readily accessible source of data and enabling a proactive approach to planning and managing explosion risk mitigation. In addition to improvements just for the research mine, this EDRMS created directly address many Queensland regulatory audit findings. By finalising the total system and making the highlighted changes for standardisation, this BI system will have the adaptable capabilities for implementation across the UCM industry. As accurate data availability improves at UCMs, further work can be done to improve the systems’ optimisation techniques and integration of other risks.

Apr 16, 2024