Search Documents

By AIME AIME

THE first meeting" of the Iron and Steel Division was held Tuesday afternoon, Feb. 17, with nearly 100 men present and C. B. Murray as chairman. This was a round table discussion of iron ore beneficiation and of its relation to blast-furnace operations, and only one paper was presented, by Clyde E. Williams. Mr. Williams discussed the future of the Lake Superior district in its relation to the iron and steel industry. He stated that although estimates had shown that the total life of the present known iron ore reserves of the Lake Superior district was 20 to 30 years and that many believed that as a result of this depletion foreign ores would be brought to the Atlantic Seaboard, thus causing a displacement of the steel industry to the East, he believed that the Lake Superior district would continue to be the important producer of iron ore used in this country for decades beyond the predicted time before the exhaustion of the present known reserves. He described the three general types of ores that required concentration and pointed out the needs for research and the proper methods to be used in processes for the beneficiation of these low-grade materials. He discussed the effects of fine concentrates and the use of agglomerated ores in the blast furnace. This general summary led to interesting and valuable discussion on the various economic, ore-dressing, and blast-furnace problems in large-scale development of beneficiation. Perry Harrison described recent developments in sintering and the properties of iron ore sinter. T. B. Counselman and W. H. Coghill discussed the merits of classification of iron ore previous to tabling. Robert Faulkner and J. E. Little described the beneficiation plant of the Bethlehem Steel Corporation.

Jan 1, 1931

By E Nettleton, A Melkumyan

A probabilistic system for autonomous tracking of excavated ore in mining would be highly valuable. Currently, mine sites can have a vast array of sensors; examples include excavator load cells, bucket volume estimators and haul truck strut pressures which can be used to gather information about the excavated ore at different locations. These sensors can be utilised efficiently to increase the accuracy of mine estimates by introducing a real-time ore tracking system. This requires the introduction of a probabilistic ore tracking framework to consistently fuse information from any sensor input. Current modelling practices are manually intensive, deterministic (no recognition of the quality of data) and generally not a complete end-to-end system. This paper will provide a novel method for tracking extensive ore properties (mass, volume) and intensive ore properties such as chemical composition (eg Fe per cent, SiO2 per cent, Al2O3 per cent). This method is proved to ensure that correct correlations between states are conserved as material is transferred, combined and/or separated at different locations with any configuration of sensor inputs. This ensures that consistency of estimates is maintained and other benefits such as real-time probabilistic reconciliation can be implemented. A method for combining material of different mass and chemical compositions is also developed to enable accurate and efficient operation of the system. Representative experiments on a small-scale and a larger field trial which mimic the mining processes of excavation, haul and unload to ROM Stockpile will be used to verify the approach.

Sep 26, 2011

By N. A. Sareyed-Dim

Nickel ores may be classified into two major categories : sulphide ores, and oxidized lateritic ores, these latter containing nearly 80% of the known reserves of the metal (1). Two types of lateritic ores are recognized; ores high in iron but low in magnesia and silica are known as "limonitic", while ores low in iron but containing high percentages of magnesia and silica are called "silicate" (see Table I). Sulphide ores can be beneficiated readily by conventional ore dressing techniques and the technology for nickel recovery from such ores has been well tested in a number of commercial processes (1-4). Unfortunately, no economically viable process for the concentration of nickel from low-grade deposits has yet been developed, and so only the high grade ores are able to be worked profitably. Silicate ores have been treated pyrometallurgically for the production of ferronickel (2) (3) (5); limonitic ores have been processed hydrometallurgically to produce nickel metal (2) (3) (6) (7).

Jan 1, 1975

By S Brown

With oxygen conditioning routinely used in both the lead and zinc circuits at Pasminco Elura Mine a more sophisticated method of determining oxygen demand was required. It is known that different ore types have different oxygen consumption rates, however oxygen is added at a fixed rate regardless of ore type in the plant. Therefore, a simple laboratory test was devised to measure the oxygen demand of ores. The paper describes the technique employed, and provides an interpretation of the results. These data, together with pulp chemical measurements (Eh, pH and EDTA extraction data) were correlated against laboratory flotation performance to establish the relationship between oxygen demand and the position of the grade/recovery curve.

Jan 1, 2000

The presence of undetonated explosives in a rock face after firing constitutes a hazard which can result in a fatal or serious accident if undetected before drilling commences.Most accidents caused by drilling into explosives are the result of failure to examine the working face properly and lack of care in subsequent drilling operations; it is not always realized that explosive may be left in the butts of holes or may be driven into cracks or crevices in the rock.Obviously the best means of preventing accidents of this nature is to adopt methods of drilling, charging and firing which will reduce the hazard to a minimum.There are three ways in which undetonated explosives may be left in the rock face, namely:1. Misfires.2. Cut-off shots.3. Incomplete detonation or failure of the charge to propagate throughout.MisfiresNo attempt will be made in this paper to deal fully with the question of the prevention of misfires, as apart from the fact that most of the preventive methods are well known, it is believed that if the miner receives his explosives and means of initiation in good order, and proper care is taken in their use, the failure of a charge to fire will be a rare occurrence. The provision of central fuse capping stations on mines has gone a long way towards the elimination of misfires caused by the mishandling of safety fuse anddetonators.

Jan 1, 1956

By L. D. Tracy

Many bituminous coal-mining companies have inaugurated extensive safety programs, but the failure to have approved or permissible equipment or safe practice in only one part of a mine has resulted in disaster. The necessity of using only equipment bearing the U. S. Bureau of Mines approval plate is emphasized by the fact that many accidents are the direct result of carelessness on the part of trusted employees using non-permissible equipment. A concrete example is found in the case of an explosion on October 26, 1926, in a mine in the Pittsburgh district, Pennsylvania. Story of the Explosion At about 10 o'clock on the night of the explosion an examination was made in No. 2 butt left and parallel off No. 14 north, and was found to be clear of dangerous accumulations of gas. (See figure). Several hours later a crew of two men brought a self-propelling rock-dusting machine within 50 feet of the face of No. 2 butt parallel before they examined for gas. The machine operator found an accumulation of explosive gas about 13 inches from the roof. He began to wave his arms thoroughly mixing the gas and air. Undoubtedly a highly explosive mixture was created, and as the men attempted to run the machine back to fresh air as explosion occurred.

Jan 1, 1927

By D A. F Oliveira, C J. Parker

The role of the virgin in situ stress field in tunnelling projects is well known in the Sydney area. The effect of in situ stresses is mostly considered through the use of published relationships that describe the in situ stress conditions as a function of depth. Considering the significant scatter in the data, it is evident that by adopting such relationships, the designers are assuming an average distribution of stresses with depth that is generally a reasonable engineering approach; however, when building a geomechanical model, the tunnelling or geotechnical engineer needs to account for the interrelationship between ground conditions (rock mass quality – fracturing, strength and stiffness) and in situ stress, which may explain part of the stress data scatter. This paper presents an alternative approach for interpreting in situ stress conditions, valid for both Sydney sandstones and shales that focus on such interrelationship between in situ stress and ground conditions.CITATION:Oliveira, D A F and Parker, C J, 2014. An alternative approach for assessing in situ stresses in Sydney, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 189–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By James J. Gusek

Passive-treatment systems that mitigate acid-rock drainage (ARD) from coal mines have operating since the mid-1980s. Large systems at metal mines are being contemplated. A 95L/sec (1500-gpm) capacity system is planned this year at an underground lead mine in Missouri. Mine, process and environmental managers need to understand how and why passive-treatment systems work. They must understand what operational limitations to expect, as well as the economics of construction and operation compared to the alternatives, like lime precipitation. Wetlands have been recognized as nature's method of improving water quality. Contaminant reductions can occur through the precipitation of metal hydroxides, sulfides and carbonates and pH adjustments. Local conditions, oxidation state and water and soil chemistries dictate whether these natural reactions will occur under oxidizing (aerobic) or reducing (anaerobic) conditions.

Jan 1, 1995

By C. Patrick

Project scheduling is a deterministic technique utilizing single estimates of activity durations. In reality, activity durations are stochastic and can be better represented by probability distributions. This paper describes the development and utilization of a project scheduling simulation which combines analytical scheduling with stochastic activity durations. The purpose is to provide a method to analyze the sequencing of mining production processes and predict the effect of any planned changes. The simulation is demonstrated through realistic examples, such as longwall face-to-face transfer sequencing and the effect of varying advance rates on longwall development sections. Statistical data, to make more informed production decisions, are generated in the form of project activity/path criticality and project duration distributions.

Jan 1, 1995

By P. G. Vikre

Several factors have caused less emphasis to be placed on geologic mapping in mineral exploration in the last 15 years. These include opportunities for "easy" discoveries of near surface gold and silver deposits in developed countries, and of base metal deposits as well in less developed countries, a decline of emphasis on geologic mapping in many universities, and a decline of useful mapping by government agencies in many areas. Geologic mapping is simply a way of recording geologic observations on volumes of rock larger than can be seen from one place. Since most geologic processes involve systems larger than this, mapping is also essential to understand the significance of observations made on smaller volumes of rock, such as thin sections and sample taken for chemical or isotopic analysis. To be useful, the observations recorded through geologic mapping are then interpreted to arrive at an understanding of the 3D geometry and geologic history of a volume of rock, which is used to direct mineral exploration, or any number of other purposes.

Jan 1, 1995

By Q. H. Bui

The elastoplastic self-consistent model is one of the effective models to study the initial microstructure effect on the mechanical behavior of bulk materials. However, the use of this micromechanics-based model which takes into account only the Hall-Petch relationship at grain level for predicting the grain sized effects on the strength of the deformed materials is not accurate yet because of the fact that the dislocation density contributes also to the strengthening of this kind of materials. In this study, a modification made to the Hill-Hutchinson elastoplastic self-consistent model was proposed for investigating the microstructure dependence of the mechanical behavior of cold-drawn 6063 aluminium tubes. Because of the novel modification, an estimation procedure with two steps was required to identify the parameters of this micromechanical model. An acceptable agreement between experimental and theoretical stress-strain curves was achieved.

Jan 1, 2011

THE following notes simply sum up the writer's experience, which extended over a very busy period of some three years, dealing with wolfram ores and concentrates. The three methods for the estimation of tungsten that are discussed below are well known, but these results of their trials and comparison under technical conditions may be interesting. Method I. The routine procedure for the assay of rich wolfram ores or concentrates was as follows: Take 1 gram of finely-ground sample; digest with HCl and HNOs for about 2 hours, evaporating down to near dryness. To the remaining 5 cc., say, of liquid, add water, warm or boil for 1 to 1.5 hour, filter through a small filter paper, and wash the beaker and the insoluble matter with hot dilute HCl. It is best to keep the bulk of the insoluble matter (WOs, Si02, etc.) in the beaker at this stage. Then plaee a weighed porcelain dish under the filter funnel and wash the beaker and the filter paper with successive small quantities of strong NHOH, finally bringing all the insoluble matter on to the filter paper, and collecting the ammoniacal filtrates in the porcelain dish (S). Then place the filter paper with the insoluble matter in a porcelain crucible, dry and burn off the paper, cool, and brush the contents of the crucible on to an agate mortar, grind it to flour, and brush this back to the original beaker without loss. In the absence of draughts this can be done safely. Re-treat this residue with' acid and ammonia as above, running the second ammoniacal filtrate into the previous porcelain dish, which in the meantime has been heating on a water-bath.Finally evaporate to dryness on the water-bath the combined ammoniaeal filtrate, and then heat gradually to a red heat over a Bunsen burner, cool, and weigh. Then the contents of the porcelain dish give the WOs (tungstie aeid) direcvly (5).The final filter paper and insoluble matter may be ignited in a porcelain crucible, thus giving the "insoluble matter." If the ore...

Jan 1, 1922

By William M. McKewan

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Ropes of sizes ranging from 3/4 to 2 in. in diameter and from 2 to 35 ft in length were tested to determine their breaking strength, elongation, and torque. This was done to characterize the test equipment on ropes used in mine hoisting systems.

Jan 1, 1990

By C Beal

Proper understanding and management of production drilling in sublevel cave (SLC) mines is essential for meeting production targets and for avoiding inefficiencies that could lead to costly bottlenecks. In many SLC mine management models drilling is considered a derivative activity of firing and bogging. Its scheduling is considered to be implied in a firing schedule and given an arbitrary target completion, ‘several weeks’ or ‘a month’, ahead of production firing. Like development, drilling activities are most efficient when conducted separately from other production activities. Unlike development, however, it is not apparent during planning and feasibility how far in advance of firing drilling activities ought to be conducted. This paper presents a method of defining a minimum threshold of drilled stocks above which drilling, firing and bogging operations occur most efficiently. As an example, the drilling activities, procedures, and maintenance at Glencore Xstrata’s Ernest Henry Mine are presented, and the larger scale consequences of improvements to these areas are presented to illustrate their importance in the operation of an SLC mine.CITATION:Beal, C, 2014. Understanding the role of production drilling and drilled stocks in efficient operation of a sublevel cave mine, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 235–242 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By A Suwandhi, H Utama

PT. Indo Muro Kencana (PT.IMK) is a gold mine that is located in Central Kalimantan, Indonesia. Drilling and blasting activity is applied in order to support mining production. Drilling and Blasting (D&B) planning is conducted by its engineers. A drilling and blasting contractor conducts drilling and blasting activity. The objective of this paper is to evaluate the implementation of the scaled depth of burial (Chiappetta and Treleven, 1997) in explosive charging sheet application to increase blast efficiency. The function of the scaled depth of burial is to maintain stemming height above explosive charge in order to prevent the ‘over energy’ condition, to reduce the excessive fly rock possibility, to maintain rock fragmentation (digger’s productivity) and to increase blast efficiency. The focus of this paper is to implement the scaled depth of burial as a reference in D&B planning and practice, especially in designing stemming height. The purpose of this paper is to validate that the scaled depth of burial can be used as an engineering tool in D&B practice in PT.IMK. However, scaled depth of burial cannot applied as an engineering tool to determine stemming height above explosive charge for trim blastholes and secondary blasting area. In general, the implementation of the scaled depth of burial in PT.IMK is applicable for production blastholes (ore and waste blasting). In conclusion, it is clear that scaled depth of burial can be used as an engineering tool to create explosive charging sheet and also to increase blast efficiency (ore and waste blasting) in PT.IMK.

Jun 22, 2022

By Michael Gay, W. H. Hansmire, G. Rippentrop, V. S. Romero

The new Tren Urbano heavy rail transit project in San Juan, Puerto Rico has one very significant part, the Río Piedras Contract, being constructed underground. This paper will give an overview of the tunneling work that started construction in1997. Design-Build procurement for tunneling is addressed. The new and modern transit system in San Juan will be 17.2 km (10.7 mi)long and have 16 stations in its first segment of construction, which is due to open in 2001. The line connects the city center district of Santurce to the outlying suburban municipality of Bayamón. All construction is being done under design-build contracts as a demonstration project funded by the Commonwealth of Puerto Rico and the Federal Transit Administration (FTA). The Río Piedras Contract is completely underground and involves practically all types of construction in soft ground. One station is built as cut-and-cover at the University of Puerto Rico. One portion has twin tunnels to be driven with an Earth Pressure Balance Machine (EPBM) and lined with one-pass precast concrete segments. Another has four short tunnel drives at a turnout that will be constructed with an initial support of shotcrete and lattice girders (i.e., the New Austrian Tunneling Method of construction). The most complex construction is the Río Piedras Station, which is being built as a stacked drift with a total of 15 individual tunnel drifts. After being sequentially excavated and concreted, they will form the arch of the 19 m (62 ft.) wide by 16 m (53 ft.) high cavern station. This structure is excavated in soil with less than 5 m (16 ft.) of cover to overlying historic buildings.

Jan 1, 1999

By S G. Gemell

"The financial model is an integral component of any project evaluation based on mineral resources, ore reserves and (at least internally) exploration targets. Given the unity of purpose for preparing financial models for project evaluation purposes, the diversity of both format and content of the finalised models is surprising. Many models are prepared by staff or consultants who are comfortable with a particular format that may be used for other purposes, such as budget preparation or financial reporting. It is natural in these situations that the practitioner will take these models and adapt them to the purpose. The end result may or may not succeed in providing a clear, accurate and sufficiently detailed view of the project’s economic viability.When preparing a model, the practitioner should be cognisant of the interpretation and review, or audit, process. The auditor may be a consultant or employee of a bank, potential equity provider or of the project sponsor itself. Depending upon the scale of the project and the level of participation of the entity that the auditor represents, the financial model will be interrogated more or less rigorously. In any event, the end user will require the model to permit easy change of inputs and will wish to confirm that such change is appropriately and thoroughly transmitted throughout.Accordingly, there are some ‘dos and don’ts’ that can be readily applied in the creation of the financial model that will greatly assist the end user, not just in the change of inputs, but also in reviewing the model’s integrity. The less time and effort required by an auditor in this regard is reflected directly in the cost of the review process.CITATION:Gemell, S G, 2016. Financial modelling with the auditor in mind, in Proceedings Project Evaluation 2016, pp 172–180 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

Extensive testing in the past ten years has shown that where a uniform natural gamma background is present in the strata bordering the seam, the thickness of the boundary coal left in place after mining can be determined by measuring the attenuation of that radiation (Nelson and Bessinger, 1989). Measurements made by the authors in underground mines in Pennsylvania, West Virginia, Ohio, Illinois, and Kentucky, and by others in Wyoming and New Mexico, have shown the presence of such a gamma background (Nelson, 1989). Natural gamma coal thickness sensors of several configurations have been tested in mines owned and operated by the Consolidation Coal Company in Pennsylvania and west Virginia (Nelson and Bessinger, 1988).

Jan 1, 1990

In this paper, the recovery of copper minerals and molybdenite in the rougher/scavenger banks of two separate mineral processing plants is compared with recovery in laboratory (batch) cells. A number of metallurgical surveys were conducted in two plants treating porphyry copper and molyb-denum ore. Batch flotation tests were performed on plant conditioned flotation feed slurry, in parallel with the plant metallurgical surveys. The effect of flotation feed density on recovery of copper minerals and molybdenite in the plant and batch laboratory cells was investigated. Changes in flotation pulp density had little effect on copper mineral recovery, in both plant and laboratory cells. The ultimate recovery for molybdenite, on the contrary, increased considerably when the pulp density was reduced, both at plant and laboratory scale. Recovery of copper minerals in the plant and laboratory cells was comparable, while molybdenite recovery in laboratory flotation cells was 3%~13% higher than in plant. It is hypothesised that the flotation rate of molybdenite is sensitive to cell hydrodynamic conditions (i.e. local turbulent energy dissipation) more than the flotation rate of copper. The flotation behaviour of molybdenite particles is likely to be predominantly controlled by bubble-particle collision frequency, which is enhanced in high local turbulent energy dissipation environment. For chalcopyrite, the flotation recovery is mostly determined by attachment and stability efficiencies. An increase in local turbulent energy dissipation, while increasing collision efficiency, may negatively impact on attachment and stability efficiencies. The outcomes may have a considerable impact on increasing molybdenite recovery from porphyry ores.

Jan 1, 2014

By W. M. Peirce

COAL'S importance in the metallurgy of zinc may be gauged by the fact that approximately a million and a half tons is so employed annually in the United States. This brief paper will show in what way the various steps in the treatment of zinc ores utilize this fuel, either in its primary form or as coke or gas, and to what extent. The first step in zinc metallurgy that requires the use of fuel is roasting the sulphide ore, which is the type of ore in which zinc commonly occurs. Since the roasting is nearly or completely autogenous, however, this use of fuel is too minor to warrant further attention. Concentration of zinc ores is usually carried out by conventional milling methods, but a pyrometallurgical method, the Waelz process, is used to concentrate certain low-grade ores, and to recover the zinc content of certain residues in concentrate form. The Waelz process uses a continuous rotary kiln in which a mixture of coal and zinc-bearing material is heated to a

Jan 1, 1948